PEERLESS LDS 1920U, LDS 1920U-S, LDS 2527U, LDS 2527U-S, LDS 32U-S Installation And Assembly Manual
...Page 1
Models:
Installation and Assembly - Universal Desktop Mount
IMPORTANT! Read entire instruction sheet before you start inst allation and assembly .
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
LDS 1920U, LDS 1920U-S,
LDS 2527U, LDS 2527U-S,
LDS 32U, LDS 32U-S
Parts List
Note: Some parts may appear slightly different than illustrated.
DESCRIPTION QTY. LDS 1920U LDS 1920U-S LDS 2527U LDS 2527U-S LDS 32U LDS 32U-S
A1 tray 19" - 20" 1 090-1243 090-4243
A2 tray 25" - 27" 090-1244 090-4244
A3 tray 32" 090-1245 090-4245
B #10 x 3/4 particle board screw 8 500-9006 500-9006 500-9006 500-9006 500-9006 500-9006
C penta-pin tool 1 520-9249 520-9249 520-9249 520-9249 520-9249 520-9249
D M5 x .8 x 10 mm phillips screw 2 520-9250 520-9250 520-9250 520-9250 520-9250 520-9250
E Peerless cover plate 2 590-1046 590-4046 590-1046 590-4046 590-1046 590-4046
F 1/4-20 x 1 3/4 bolt 1 520-9204 520-9204 520-9204 520-9204 520-9204 520-9204
G spacer 3 540-9455 540-9455 540-9455 540-9455 540-9455 540-9455
H M5 x .8 x 10 mm penta-pin™ screw 2 505-9010 500-2001 505-9010 500-2001 505-9010 500-2001
I 1/4-20 3 prong T-nut 1 530-9301 530-9301 530-9301 530-9301 530-9301 530-9301
J #1 x 1-1/4 phillips pan wood screw 1 510-9157 510-9157 510-9157 510-9157 510-9157 510-9157
K swivel base 1 090-0246 090-0247 090-0246 090-0247 090-0246 090-0247
L adhesive bumper strip 1 570-1029 570-1029 570-1029 570-1029 570-1029 570-1029
B C
H
A2A1
D
I
J
E
K
A3
F
G
L
Before you start make sure all parts listed are included with your product.
1 of 5
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Page 2
WARNING
• Do not lift more weight than you can handle. Use additional manpower or mechanical lifting equipment to safely lift
and attach the television!
For flat screenTVs, peel paper from adhesive
bumper strip (L) and place flush to the front lip
on bottom of TV .
For Zenith
adhesive bumber strip (L). Peel paper from
longer strip and place flush to the front lip on
bottom of TV as shown in figure 1. Also, peel
paper from the 1" strips and place on front feet
of TV as indicated.
Turn TV upside down and determine mounting
locations. For TV’s with a flat front, make sure that
leading edge of screen is flush with leading edge of
tray. For TV’s with a curved front, mount screen as
close to the front of leading edge of tray with tray
still being hidden. Attach tray to TV by installing
four screws (B) into TV mounting bosses.
H32F56, cut 1" strips off each side of
FRONT LIP OF TV
figure 1
L
1" STRIPS
BOTTOM OF TV
B
TOP VIEW
x
LEADING EDGE
TRAY
OF
SCREEN
OF
EDGE
LEADING
x = leading edge of tray to leading edge of screen
Note: If TV is flush with tray, x = 0.
2 of 5
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Page 3
There are two methods of installation. Follow steps 2 and 4 for installation using four 3/4" particle board
screws or steps 3 and 5 to use one 1-3/4" bolt.
Determine position on desktop to secure mount.
See Note below. The leading edge of TV should
be flush with edge of mounting surface once TV is
installed. Once position is determined, align .281"
diameter holes in swivel base (marked 1-4 below)
with holes in race. Mark holes and drill 1/8" (3
mm) diameter pilot holes 3/4" (19 mm) into
mounting surface.
1
4
3
EDGE
1.25"
2
EDGE OF TRAY
y
For mounting to surface using one 1-3/4" bolt,
determine position on desktop to secure mount.
See Note below. The leading edge of TV should
be flush with edge of mounting surface once TV is
installed. Mark holes and drill one 5/16" (8 mm)
diameter thru hole and one 1/8" (3 mm) diameter
pilot hole 3/4" (19 mm) into mounting surface.
1/8" (3 MM)
DIA. PILOT
1
EDGE
1.25"
HOLE
5/16" (8 MM)
DIA. THRU
HOLE
EDGE OF TRAY
y
EDGE OF MOUNTING SURFACE
Note: T o figure out where to mount swivel base so TV is
flush with the edge of the mounting surface, use
the following formula:
y = x + 1.25"
Use distance x from step 1 on previous page.
EDGE OF MOUNTING SURFACE
Note: T o figure out where to mount swivel base so TV is
flush with the edge of the mounting surface, use
the following formula:
y = x + 1.25"
Use distance x from step 1 on previous page.
3 of 5
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Page 4
Align holes in race with holes 1 through 4 of swivel
base. Once position is determined, attach swivel
base to surface using four screws (B) into positions 1 through 4. If swivel restriction is needed,
use one spacer (G) and screw (B) in position 1 and
then refer to step 6. If you would like to prevent the
swivel base from swiveling at all, install one screw
(J) into back hole #1 instead of screw (B) and
spacer (G).
B
Align holes in race with holes 1 through 4 of swivel
base. Once position is determined, attach swivel
base to surface using one screw (F) and one T-nut
(I) in center of swivel base and one screw (B) and
one spacer (G) in back hole #1. If swivel restriction
is needed, use one spacer (G) and screw (B) in
position 1 and then refer to step 6. If you would like
to prevent the swivel base from swiveling at all,
install one screw (J) into back hole #1 instead of
screw (B) and spacer (G).
J
F
B
4
3
1
2
G
4
3
1
2
G
I
Swivel Restriction
Tray swivel can be stopped entirely (as described in steps 4 and 5) or restricted to either 10, 30, 60, or 90
degrees. To restrict swivel, place two screws (D) with spacers (G) into holes on lef t and on right at desired
degree.
0°
10°
30°
10°
30°
G
D
60°
90°
4 of 5
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
60°
90°
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Page 5
Attach tray , with TV mounted onto it, to swivel base by
sliding trays together. The lip of the tray (as shown) will
lock into the slot in swivel base. The slot of the two
tabs in the tray will align with the two holes on the
swivel base.
To lock trays together , be cert ain that the hole in the
swivel base is centered within the slot in the tray (see
detail below). Secure on left and right using two pentapin screws (H) with tool (C).
H
HOLE
SLOT
DETAIL
LIP
TABS
SLOT
HOLES
Finish by snapping two Peerless cover plates (E)
onto tray as shown.
E
5 of 5
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
© 2004 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10
Loading...