PEERLESS LDS 1920U, LDS 1920U-S, LDS 2527U, LDS 2527U-S, LDS 32U-S Installation And Assembly Manual

Models:

Installation and Assembly - Universal Desktop Mount

IMPORTANT! Read entire instruction sheet before you start inst allation and assembly .

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

LDS 1920U, LDS 1920U-S,
LDS 2527U, LDS 2527U-S,
LDS 32U, LDS 32U-S

Parts List

Note: Some parts may appear slightly different than illustrated.

DESCRIPTION QTY. LDS 1920U LDS 1920U-S LDS 2527U LDS 2527U-S LDS 32U LDS 32U-S

A1 tray 19" - 20" 1 090-1243 090-4243
A2 tray 25" - 27" 090-1244 090-4244
A3 tray 32" 090-1245 090-4245

B #10 x 3/4 particle board screw 8 500-9006 500-9006 500-9006 500-9006 500-9006 500-9006
C penta-pin tool 1 520-9249 520-9249 520-9249 520-9249 520-9249 520-9249
D M5 x .8 x 10 mm phillips screw 2 520-9250 520-9250 520-9250 520-9250 520-9250 520-9250
E Peerless cover plate 2 590-1046 590-4046 590-1046 590-4046 590-1046 590-4046
F 1/4-20 x 1 3/4 bolt 1 520-9204 520-9204 520-9204 520-9204 520-9204 520-9204
G spacer 3 540-9455 540-9455 540-9455 540-9455 540-9455 540-9455
H M5 x .8 x 10 mm penta-pin™ screw 2 505-9010 500-2001 505-9010 500-2001 505-9010 500-2001
I 1/4-20 3 prong T-nut 1 530-9301 530-9301 530-9301 530-9301 530-9301 530-9301
J #1 x 1-1/4 phillips pan wood screw 1 510-9157 510-9157 510-9157 510-9157 510-9157 510-9157
K swivel base 1 090-0246 090-0247 090-0246 090-0247 090-0246 090-0247

L adhesive bumper strip 1 570-1029 570-1029 570-1029 570-1029 570-1029 570-1029

B C

H

A2A1

D

I

J

E

K

A3

F

G

L

Before you start make sure all parts listed are included with your product.

1 of 5

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.

ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10

WARNING

• Do not lift more weight than you can handle. Use additional manpower or mechanical lifting equipment to safely lift
and attach the television!

For flat screenTVs, peel paper from adhesive
bumper strip (L) and place flush to the front lip
on bottom of TV .

For Zenith
adhesive bumber strip (L). Peel paper from
longer strip and place flush to the front lip on
bottom of TV as shown in figure 1. Also, peel
paper from the 1" strips and place on front feet
of TV as indicated.

Turn TV upside down and determine mounting
locations. For TV’s with a flat front, make sure that
leading edge of screen is flush with leading edge of
tray. For TV’s with a curved front, mount screen as
close to the front of leading edge of tray with tray
still being hidden. Attach tray to TV by installing
four screws (B) into TV mounting bosses.

H32F56, cut 1" strips off each side of

FRONT LIP OF TV

figure 1

L

1" STRIPS

BOTTOM OF TV

B

TOP VIEW

x

LEADING EDGE

TRAY

OF

SCREEN

OF

EDGE

LEADING

x = leading edge of tray to leading edge of screen

Note: If TV is flush with tray, x = 0.

2 of 5

Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.

ISSUED: 11-05-04 SHEET #: 090-9102-4 09-27-10