Peerless-AV LCZ-4F4G30B User Manual [en, es, fr]
Installation and Assembly:
Quad Monitor Grommet for up to 24” Monitors
Models: LCZ-4F4G30B
Max Load Capacity per display: 19.8 lb (9 kg)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws fi rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• Be sure to use designated fasteners and tools to assemble product. If correct fasteners and tools are not used,
product may fail.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation of Base .................................................................................................................................................................4
Attaching Mounting Plates to Display .....................................................................................................................................7
2 of 26
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Before you begin, make sure all parts shown are included with your product.
y
Parts List
Description
A base cover 1
pressure clamp
B
C mounting bracket 4
D pole 1
E lock collar
F crossbar
G M4 x 12mm screw
H M4 x 30mm screw
I
spacer
J knob
K cable clip
L 3mm allen wrench
M 4mm allen wrench
Parts may appear slightly different than illustrated.
D
E
G
Qt
1
2
2
16
16
16
4
2
1
1
H
A
B
C
J
F
I
M
L
K
3 of 26
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Installation of Base
Base assembly can be attached to a mounting surface with a maximum thickness of 3-1/2" (90mm).
1
Set base (A) on mounting surface as shown in fi gure 1.1 and mark the center of the base. Drill a 3/8" (10mm) dia.
hole through mounting surface. OPTIONAL: Drill a 3/4" (19mm) dia. hole for cable management.
Remove base cover from base (A). Place base on mounting surface and secure using pressure clamp (B) as
shown in fi gure 1.2.
Hand tighten pole (D) onto base (A) as shown in fi gure 1.3. Tigthen set screw to secure pole using 3mm allen
wrench (L) as shown in rear view.
fi g 1.1
A
CABLE
MANAGEMENT
HOLE
A
B
SET SCREW
fi g 1.2
fi g 1.3
D
REAR VIEW
4 of 26
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Feed cables through base cover. Insert base cover
2 3
onto pole (D).
Insert lock collar (E) onto pole (D).
Adjust to desired height and tighten by hand.
BASE COVER
D
E
D
5 of 26
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Insert crossbar (F) onto pole (D) and let it rest on lock collar (E) as shown in fi gure 4.1.
4
Adjust rotation of crossbar and hand tighten knob as shown in fi gure 4.2.
Repeat steps 3 and 4 for second lock collar (E) and crossbar (F).
4.1
F
D
E
fi g 4.2
KNOB
Cables may be routed through crossbar by removing crossbar covers.
5
CABLES
CROSSBAR COVERS
6 of 26
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Attaching Mounting Plates to Display
WARNING
• Tighten screws so mounting plates are fi rmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
To prevent scratching the screen, set a cloth on a fl at, level surface that will support the weight of the display. Place
6
display face side down. If display has knobs on the back, remove them to allow the mounting plates to be attached.
Place mounting plates (C) on back of display.
Choose hole pattern as shown in detail 1.
FOR DISPLAYS WITH FLAT BACKS: Attach mounting plates (C) to display using four 12mm screws (G) as shown
in fi gure 6.1.
FOR DISPLAYS WITH RECESSED BACKS: Attach mounting plates (C) to display using four 30mm screws (H)
and four spacers (I) as shown in fi gure 6.2.
C
VESA 100mm
VESA 75mm
DETAIL 1
VESA 75mm
G
fi g 6.1
VESA 100mm
C
H
I
fi g 6.2
7 of 26
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Hook mounting brackets (C) onto crossbar (F).
7
Adjust position of displays horizontally to desired location and install knobs (J) into rear of mounting brackets.
Knobs (J) may be tightened using 3mm allen wrench (L).
C
F
J
Cables may be routed using cable clip (K).
8
J
K
CABLES
8 of 26
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Loading...