Peerless-AV LCZ-3F419B - Installation User Manual [en, es, fr]

Loading...

Installation and Assembly:

Widescreen Triple Monitor Table Stand for 14" - 19" Displays

Models: LCZ-3F419B

Max Load Capacity per display: 19.8 lb (9 kg)

2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com

ISSUED: 04-05-11 SHEET #: 090-9199-3 05-29-12

NOTE: Read entire instruction sheet before you start installation and assembly.

WARNING

Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.

This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Never exceed the Maximum Load Capacity. See page one.

Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

Be sure to use designated fasteners and tools to assemble product. If correct fasteners and tools are not used, product may fail.

Table of Contents

 

Parts List.................................................................................................................................................................................

3

Installation of Base .................................................................................................................................................................

4

Attaching Mounting Plates to Display.....................................................................................................................................

6

2 of 23

ISSUED: 04-05-11 SHEET #: 090-9199-3 05-29-12

Before you begin, make sure all parts shown are included with your product.

Parts List

 

 

Description

Qty

 

A

base

1

 

B

mounting bracket

3

 

C

pole

1

 

D

lock collar

1

 

E

crossbar

1

 

F

M4 x 12mm screw

12

 

G

M4 x 30mm screw

12

 

H

spacer

12

 

I

knob

3

 

J

cable clip

1

 

K

3mm allen wrench

1

 

L

4mm allen wrench

1

Parts may appear slightly different than illustrated.

A

B

C D F G

E

H

L

I

J

K

3 of 23

ISSUED: 04-05-11 SHEET #: 090-9199-3 05-29-12

Installation of Base

1

Remove base cover from base (A) as shown in figure 1.1.

 

Hand tighten pole (C) onto base (A) as shown in figure 1.2. Tigthen set screw to secure pole using 3mm allen

 

wrench (K) as shown in rear view.

BASE COVER

C

A

fig 1.1

2

Feed cables through base cover. Insert base cover

onto pole (C).

BASE COVER

C

fig 1.2

SET SCREW

 

REAR VIEW

3

Insert lock collar (D) onto pole (C).

 

Adjust to desired height and tighten by hand.

D

C

4 of 23

ISSUED: 04-05-11 SHEET #: 090-9199-3 05-29-12

4

Insert crossbar (E) onto pole (C) and let it rest on lock collar (D) as shown in figure 4.1.

 

Adjust rotation of crossbar and hand tighten knob as shown in figure 4.2.

fig 4.1

fig 4.2

E

C

D

KNOB

5 Cables may be routed through crossbar by removing crossbar covers.

CABLES

CROSSBAR COVERS

5 of 23

ISSUED: 04-05-11 SHEET #: 090-9199-3 05-29-12

Attaching Mounting Plates to Display

WARNING

Tighten screws so mounting plates are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

6

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the display. Place

display face side down. If display has knobs on the back, remove them to allow the mounting plates to be attached.

Place mounting plates (B) on back of display. Choose hole pattern as shown in detail 1.

FOR DISPLAYS WITH FLAT BACKS: Attach mounting plates (B) to display using four 12mm screws (F) as shown in figure 6.1.

FOR DISPLAYS WITH RECESSED BACKS: Attach mounting plates (B) to display using four 30mm screws (G) and four spacers (H) as shown in figure 6.2.

VESA 100mm

fig 6.1

VESA 75mm

 

VESA 75mm

VESA 100mm

DETAIL 1

fig 6.2

B

F

B

G

H

6 of 23

ISSUED: 04-05-11 SHEET #: 090-9199-3 05-29-12

7

Hook mounting brackets (B) onto crossbar (E).

 

Adjust position of displays horizontally to desired location and install knobs (I) into rear of mounting brackets.

Knobs (I) may be tightened using 3mm allen wrench (K).

B

E

I

 

I

8 Cables may be routed using cable clip (J).

J

CABLES

7 of 23

ISSUED: 04-05-11 SHEET #: 090-9199-3 05-29-12

+ 16 hidden pages