PARKSIDE PBSA 12 D3 User manual [it]

TRAPANO AVVITATORE RICARICABILE PBSA 12 D3
Traduzione delle istruzioni d’uso originali
AKKU-BOHRSCHRAUBER
Originalbetriebsanleitung
IAN 322702_1901
CORDLESS DRILL
Translation of the original instructions
Prima di leggere aprire la pagina con le immagini e prendere confidenza con le diverse funzioni dell'apparecchio.
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen des Gerätes vertraut.
IT / MT Traduzione delle istruzioni d’uso originali Pagina 1 GB / MT Translation of the original instructions Page 15 DE / AT / CH Originalbetriebsanleitung Seite 27
10a
A
Los tiempos
de carga
Tempi di
ricarica
Corrientes
de carga
La corrente
di ricarica
max. 2,4 A
Cargador
Carica-
batteria
PLGK 12 A1
max. 4,5 A
Cargador
Carica-
batteria
PLGK 12 B2
2 Ah
Acumulador
Accumulatore
PAPK 12 A1
60 min
2,4 A
60 min
2,4 A
2 Ah
Acumulador
Accumulatore
PAPK 12 A2
60 min
2,4 A
45 min
3,5 A
4 Ah
Acumulador
Accumulatore
PAPK 12 B1
120 min
2,4 A
60 min
4,5 A
Tutti gli utensili Parkside e i caricabatterie PLGK 12 A1 / B2 della serie X12V
Team sono compatibili con la batteria PAPK 12 A1 / A2 / B1.
12V max.
10,8V
Indice
Introduzione .....................................................2
Uso conforme ............................................................... 2
Dotazione .................................................................. 2
Materiale in dotazione ........................................................ 2
Dati tecnici ................................................................. 2
Indicazioni generali di sicurezza per elettroutensili .....................3
1. Sicurezza sul posto di lavoro ................................................. 4
2. Sicurezza elettrica ......................................................... 4
3. Sicurezza delle persone ..................................................... 4
4. Uso e trattamento dell’elettro utensile ........................................... 5
5. Uso e trattamento dell’utensile a batteria ....................................... 5
6. Assistenza ............................................................... 6
Avvertenze sulla sicurezza per avvitatori a batteria .................................. 6
Accessori/apparecchi addizionali originali ........................................ 6
Indicazioni relative alla sicurezza per caricabatterie ................................. 7
Prima della messa in funzione .......................................7
Prelievo / caricamento / inserimento del pacco batteria .............................. 7
Lettura dello stato di carica della batteria ......................................... 7
Sostituzione degli utensili ...................................................... 8
Trasmissione a 2 velocità ......................................................8
Rimozione del mandrino per punte da trapano ..................................... 8
Utilizzo della sede della punta .................................................. 8
Preselezione del momento torcente / livello di perforazione ........................... 8
Messa in funzione .................................................9
Cambiamento del senso di rotazione / sbloccaggio dell'apparecchio ................... 9
Accensione/spegnimento ...................................................... 9
Regolazione del velocità ...................................................... 9
Attivazione del blocco ........................................................ 9
Consigli e suggerimenti .......................................................9
Manutenzione e pulizia ...........................................10
Garanzia della Kompernass Handels GmbH ..........................10
Assistenza ......................................................12
Importatore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Smaltimento ....................................................12
Traduzione della dichiarazione di conformità originale .................13
Ordinazione di una batteria di ricambio .............................14
Ordine telefonico ...........................................................14
PBSA 12 D3
IT│MT 
 1
TRAPANO AVVITATORE
10a
RICARICABILE PBSA 12 D3
Introduzione
Ci congratuliamo per l'acquisto del vostro nuovo apparecchio. È stato scelto un prodotto di alta qualità. Il manuale di istruzioni è parte integrante del presente prodotto. Esso contiene importanti indicazioni per la sicurezza, l'uso e lo smaltimento. Prima di utilizzare il prodotto, acquisire dimesti­chezza con tutte le indicazioni relative ai comandi e alla sicurezza. Utilizzare il prodotto solo come descritto e per i campi d'impiego indicati. In caso di cessione del prodotto a terzi, consegnare anche tutta la relativa documentazione.
Uso conforme
Questo apparecchio è destinato a praticare fori e avvitare in legno, plastica e metallo. Utilizzare l'apparecchio solo nei modi descritti e per i campi di utilizzo indicati. Qualunque altro impiego e qua­lunque modifica dell'apparecchio sono da conside­rarsi non conformi alla destinazione e comportano il rischio di infortuni. Il produttore non si assume alcuna responsabilità per i danni derivanti da uso non conforme. Questo prodotto non è destinato all'uso commerciale.
Dotazione
Selettore di marcia Indicatore LED (stato di carica della batteria) Commutatore del senso di rotazione / blocco Interruttore ON/OFF Impugnatura morbida Pacco batteria Tasto per lo sbloccaggio del pacco batteria Luce di lavoro LED Preselezione momento torcente / livello di
perforazione
Mandrino per punte da trapano a serraggio
rapido Anello per mandrino per punte da trapano Sede della punta Portainserti
Figura A:
LED di controllo carica rosso LED di controllo carica verde
Caricabatterie
Materiale in dotazione
1 trapano avvitatore ricaricabile 1 caricabatterie rapido 1 pacco batteria 1 valigetta da trasporto 1 manuale di istruzioni per l'uso
Dati tecnici
Trapano avvitatore ricaricabile: PBSA 12 D3:
Tensione nominale: 12 V
Velocità nominale in folle: 1ª marcia: n
Capacità di serraggio del mandrino per punte da trapano
Diametro di foratura max.: acciaio: 8 mm
Pacco batteria: PAPK 12 A2:
Tipo: IONI DI LITIO Tensione nominale: 12 V
Celle: 3 Capacità: 2000 mAh (24 Wh)
: max Ø 10 mm
(corrente continua)
0 - 350 giri/min.
2° marcia: n0 0 - 1300 giri/min.
Legno: 20 mm
(corrente continua)
0
2 │ IT
MT
PBSA 12 D3
Caricabatterie rapido: PLGK 12 A1:
T2A
INGRESSO / input:
Tensione nominale: 220 - 240 V ~, 50-60 Hz
(tensione alternata)
Potenza assorbita nominale: 50 W
Fusibile (interno): 2 A
USCITA / output:
Tensione nominale: 12 V
(corrente continua) Corrente nominale: 2400 mA Durata del caricamento: circa 60 min
Classe di protezione: II /
(isolamento doppio)
Valore di emissione acustica:
Valore misurato relativo al rumore rilevato ai sensi della norma EN 62841. Il valore tipico del livello di rumore ponderato A dell'elettroutensile è:
Livello di pressione acustica: L Fattore di incertezza K: K Livello di potenza acustica: L Fattore di incertezza K: K
= 71,1 dB (A)
PA
= 3 dB
PA
= 82,1 dB (A)
WA
= 3 dB
WA
Valore di emissione delle vibrazioni:
Valori totali di vibrazione (somma dei vettori di tre direzioni) rilevati ai sensi della norma EN62841:
Perforazione del metallo: Valore di emissione delle
vibrazioni
= 1,987 m/s
a
h,D
Fattore di incertezza K = 1,5 m/s
2
2
Avvitatura senza percussione: Valore di emissione delle
vibrazioni ah = 0,781 m/s2 Fattore di incertezza K = 1,5 m/s
2
NOTA
Il valore complessivo delle vibrazioni e il
valore di emissione acustica indicati sono stati misurati secondo un procedimento di prova standardizzato e possono essere usati per il confronto tra due elettroutensili.
Il valore complessivo delle vibrazioni e il
valore di emissione acustica indicati possono anche essere usati per una stima provvisoria del carico.
AVVERTENZA!
Il valore di emissione delle vibrazioni e il
valore di emissione acustica possono scostarsi dai valori indicati a seconda del modo in cui l'elettroutensile viene utilizzato e, in particola
-
re, del modo in cui il pezzo viene lavorato.
Cercare di ridurre il più possibile la solle
­citazione. Provvedimenti adeguati per la riduzione della sollecitazione da vibrazioni prevedono l'uso di guanti durante l'impiego dell'elettroutensile e la limitazione dei tempi di lavoro. Occorre tenere in considerazione tutte le componenti del ciclo di esercizio (per esempio i tempi nei quali l'elettroutensile è spento e i tempi in cui è acceso ma funziona senza carico).
Indicazioni generali di sicurezza per elettroutensili
AVVERTENZA!
► Osservare tutte le indicazioni relative alla
sicurezza, le istruzioni, le illustrazioni e i dati tecnici di cui è dotato questo elettrou­tensile. Il mancato rispetto delle seguenti
istruzioni può causare scosse elettriche, incendi e/o gravi lesioni.
Conservare le indicazioni relative alla sicu­rezza e le istruzioni per uso futuro.
Il termine “elettroutensile” utilizzato nelle indicazioni relative alla sicurezza si riferisce a elettroutensili collegabili alla rete elettrica (con cavo di rete) o a elettroutensili a batteria (senza cavo di rete).
PBSA 12 D3
IT│MT 
 3
1. Sicurezza sul posto di lavoro
a) Mantenere l’area di lavoro pulita e ben illu-
minata. Il disordine e la scarsa illuminazione
dell’area di lavoro potrebbero dare luogo a infortuni.
b) Non lavorare con elettroutensili in ambienti
a rischio di esplosione, in presenza di liquidi, gas o polveri infiammabili. Gli elettroutensili
generano scintille che possono incendiare la polvere o i vapori.
c) Tenere lontani i bambini e altre persone
durante l’uso dell’elettroutensile. In caso di distrazione, si potrebbe perdere il controllo dell’elettroutensile.
2. Sicurezza elettrica
a) La spina dell’elettroutensile deve essere ido-
nea all’inserimento nella presa. La spina non deve essere assolutamente modificata. Non utilizzare connettori adattatori con elettroutensili collegati a terra. Le spine non
modificate e le prese idonee riducono il rischio di scosse elettriche.
b) Evitare il contatto corporeo con superfici col-
legate a terra, come tubi, termosifoni, fornelli e frigoriferi. Quando il corpo è a diretto contatto
col suolo, sussiste un maggiore pericolo di scosse elettriche.
c) Tenere gli elettroutensili lontano dalla pioggia
o dall’umidità. La penetrazione di acqua in un apparecchio elettrico aumenta il rischio di scosse elettriche.
d) Non utilizzare il cavo di allacciamento per
scopi non conformi, come ad es. per tra­sportare l’elettroutensile, per appenderlo o per scollegare la spina dalla presa. Tenere il cavo di allacciamento lontano dal calore, dall’olio, da angoli acuminati o da parti in movimento. Cavi di allacciamento danneggiati
o aggrovigliati aumentano il rischio di scosse elettriche.
e) Se si lavora all’aperto con un elettroutensile,
utilizzare solo prolunghe ammesse anche per uso esterno. L’utilizzo di un cavo di prolunga
idoneo all’uso esterno riduce il rischio di scosse elettriche.
f) Se è inevitabile l’uso dell’elettroutensile in
un ambiente umido, utilizzare un interruttore differenziale. L’uso di un interruttore differenziale
evita il rischio di scosse elettriche.
3. Sicurezza delle persone
a) Prestare attenzione controllando le operazioni
in corso e procedendo con cura quando si lavora con un elettroutensile. Non utilizzare l’elettroutensile se non si è concentrati o ripo­sati a sufficienza, o se si è sotto l’influsso di droghe, alcol o farmaci. Un solo momento di
disattenzione nell’uso dell’elettroutensile può dare luogo a gravi lesioni.
ndossare dispositivi di protezione individuali
b) I
e sempre occhiali di protezione. L’uso di un
dispositivo di protezione individuale come ma­scherina antipolvere, scarpe antiscivolo, casco protettivo o paraorecchi acustici, a seconda dell’uso e dell’impiego dell’elettroutensile, riduce il rischio di lesioni.
c) Evitare l’accensione involontaria. Accertarsi
che l’elettroutensile sia spento prima di col­legarlo all’alimentazione e/o alla batteria, sollevarlo o trasportarlo. Se si tiene il dito
sull’interruttore mentre si sposta l’elettroutensile o si collega l’elettroutensile alla rete elettrica con l’interruttore su ON, si possono verificare infortuni.
d) Rimuovere gli utensili di regolazione o le
chiavi per dadi prima di accendere l’elettro­utensile. Un utensile o una chiave lasciati in
una parte rotante dell’elettroutensile possono provocare lesioni.
e) Evitare posture innaturali. Provvedere a una
posizione sicura e mantenere sempre l’equi­librio. In tal modo si può controllare meglio
l’elettroutensile, soprattutto in situazioni imprevi­ste.
f) Indossare un abbigliamento idoneo. Non in-
dossare abiti larghi o gioielli. Tenere lontani i capelli e gli indumenti dalle parti in movimen­to. Gli abiti larghi e sciolti, i gioielli o i capelli
lunghi possono impigliarsi nelle parti mobili.
4 │ IT
MT
PBSA 12 D3
g) Se è possibile montare dispositivi aspirapol-
vere e aspiratrucioli, occorre collegarli e utilizzarli correttamente. L’uso di un aspiratore
per polvere può ridurre i pericoli associati alla polvere.
h) Anche se si è acquisita dimestichezza con
l’apparecchio usandolo spesso, non sentirsi troppo sicuri e non mancare di rispettare le regole sulla sicurezza nell’uso di elettroutensi­li. Una piccola disattenzione può dare luogo a
gravi lesioni in una frazione di secondo.
4. Uso e trattamento dell’elettro­utensile
a) Non sovraccaricare l’elettroutensile. Utilizzare
l’elettroutensile idoneo al proprio lavoro. Con
l’elettroutensile adatto si lavora meglio e con maggiore sicurezza nell’intervallo di potenza indicato.
b) Non utilizzare elettroutensili con interruttore
guasto. Un elettroutensile che non si riesce più a spegnere o ad accendere è pericoloso e deve essere riparato.
c) Staccare la spina dalla presa di corrente
e/o rimuovere la batteria, se sfilabile, prima di eseguire impostazioni sull’apparecchio, sostituire gli utensili o riporre l’elettroutensile.
Questa misura precauzionale consente di impe­dire l’avvio involontario dell’elettroutensile.
d) Conservare gli elettroutensili non utilizzati
fuori della portata dei bambini. Non consenti­re l’uso dell’elettroutensile a persone inesperte o che non abbiano letto le presenti istruzioni.
Gli elettroutensili sono pericolosi se utilizzati da persone inesperte.
e) Trattare gli elettroutensili e gli utensili con
cura. Controllare che le parti mobili dell’appa­recchio funzionino perfettamente e non si inceppino e che non vi siano elementi rotti o danneggiati al punto da compromettere la funzione dell’elettroutensile. Fare riparare le parti danneggiate prima di utilizzare l’e­lettroutensile. Molti infortuni derivano da una
cattiva manutenzione degli elettroutensili.
f) Mantenere gli utensili da taglio ben affilati e
puliti. Gli utensili da taglio trattati con cura e con bordi di taglio affilati si inceppano meno
spesso e sono più facili da controllare.
g) Utilizzare elettroutensili, utensili, ecc. conformi
a queste istruzioni. Tenere conto delle con­dizioni di lavoro e dell’attività da eseguire.
L’uso di elettroutensili per applicazioni diverse da quelle previste può dare luogo a situazioni di pericolo.
h) Mantenere le impugnature e le superfici di
presa asciutte, pulite e prive di olio e grasso.
Impugnature e superfici di presa scivolose non consentono un controllo e un utilizzo sicuro dell’elettroutensile in situazioni impreviste.
5. Uso e trattamento dell’utensile a batteria
a) Caricare le batterie solo con i caricabatterie
che vengono consigliati dal costruttore. Se un
caricabatterie adatto a un determinato tipo di batteria viene utilizzato con batterie diverse, vi è pericolo di incendio.
b) Utilizzare solo le batterie appositamente
previste per gli elettroutensili. L’uso di batterie diverse può dare luogo a lesioni e al rischio di incendio.
c) Tenere la batteria non utilizzata lontano
da graffette, monete, chiavi, chiodi, viti o altra minuteria in metallo, poiché tali oggetti potrebbero provocare un cortocircuito fra i contatti. Un cortocircuito fra i contatti della
batteria può dare luogo a ustioni o incendio.
d) In caso di utilizzo errato, potrebbe fuoriuscire
del liquido dalla batteria. Evitare il contatto con questo liquido. In caso di contatto acci­dentale, sciacquare con acqua. Se il liquido entra a contatto con gli occhi, consultare un medico. Il liquido che fuoriesce dalla batteria
potrebbe provocare irritazioni cutanee o ustioni.
e) Non utilizzare una batteria danneggiata o
modificata. Batterie danneggiate o modificate possono comportarsi in modo imprevisto e provocare incendio, esplosione o pericolo di lesioni.
f) Non esporre mai una batteria a fuoco o alte
temperature. Fuoco o temperature superiori a 130 °C (265 °F) possono provocare un’esplo­sione.
PBSA 12 D3
IT│MT 
 5
g) Seguire tutte le indicazioni per la carica e non
caricare mai la batteria o l’utensile a batte­ria al di fuori dell’intervallo di temperatura indicato nel presente manuale di istruzioni per l’uso. Un caricamento sbagliato o il carica-
mento al di fuori dell’intervallo di temperatura consentito potrebbe distruggere la batteria e aumentare il pericolo d’incendio.
CAUTELA! PERICOLO DI ESPLOSIONE! Non caricare mai batterie non ricari­cabili.
Proteggere la batteria dal calore, per es. anche da irradiazione solare per­manente, fuoco, acqua e umidità.
Sussiste il pericolo di esplosione.
6. Assistenza
a) Fare riparare l’elettroutensile solo da persona-
le qualificato specializzato e solo con ricambi originali. In tal modo si garantisce che la sicu-
rezza dell’elettroutensile venga mantenuta.
b) Non sottoporre mai a manutenzione le batte-
rie danneggiate. Si consiglia di far eseguire la manutenzione delle batterie solo dal produttore o dal centro di assistenza clienti autorizzato.
Avvertenze sulla sicurezza per avvitatori a batteria
Avvertenze relative alla sicurezza per tutti i lavori
AVVERTENZA!
■ Tenere l’elettroutensile per le superfici
isolate dell’impugna tura qualora venissero effettuati lavori durante i quali l’utensile potrebbe venire a contatto con cavi elettrici nascosti oppure con il cavo di collegamento dell’apparecchio stesso. Il contatto della vite
o dell'utensile con una linea che conduce tensione può mettere sotto tensione anche le parti metalliche dell'apparecchio e causare così una scossa elettrica.
Indicazioni sulla sicurezza nell’uso di punte lunghe
■ Non lavorare in nessun caso con un numero
di giri maggiore di quello massimo ammissi­bile per la punta. A numeri di giri maggiori, se
la punta può girare liberamente senza contatto con il pezzo in lavorazione, può piegarsi legger­mente causando lesioni.
■ Iniziare a trapanare sempre con un numero
di giri ridotto e quando la punta è a contatto con il pezzo in lavorazione. A numeri di giri
maggiori, se la punta può girare liberamente senza contatto con il pezzo in lavorazione, può piegarsi leggermente causando lesioni.
Non esercitare una pressione eccessiva ed
esercitare la pressione solo in senso longitudi­nale rispetto alla punta. Le punte potrebbero piegarsi spezzandosi o causando una perdita di controllo ed eventuali lesioni.
6 │ IT
MT
Accessori/apparecchi addizionali originali
■ Utilizzare solo accessori e apparecchi ag-
giuntivi che sono indicati nel manuale o la cui sede sia compatibile con l’apparecchio.
PBSA 12 D3
Indicazioni relative alla sicurezza per caricabatterie
Questo apparecchio può essere
utilizzato dai bambini a partire da­gli 8anni di età e da persone con capacità fisiche, sensoriali o mentali ridotte o insufficiente esperienza o conoscenza, solo se sorvegliati o istruiti sull'uso sicuro dell'apparec­chio e qualora ne abbiano compre­so i pericoli associati. I bambini non devono giocare con l'apparecchio. La pulizia e la manutenzione a cura dell'utente non devono essere eseguite da bambini, a meno che non siano sorvegliati.
Il caricabatterie è indicato
solo per l'uso in ambienti interni.
AVVERTENZA!
In caso di danni al cavo di rete dell'appa-
recchio, farlo sostituire dal produttore, dal servizio di assistenza clienti o da personale altrettanto qualificato, per evitare danni.
ATTENZIONE!
Il presente caricabatteria è indicato sola-
mente per la ricarica delle seguenti batterie: PAPK 12 A1 / PAPK 12 A2, PAPK 12 B1.
Su www.lidl.de/akku è disponibile un elenco
aggiornato di tutte le batterie compatibili.
Prima della messa in funzione
Prelievo / caricamento / inserimento del pacco batteria
NOTA
La batteria è parzialmente carica. Idealmen-
te, caricare completamente la batteria prima dell’uso. È possibile caricare la batteria agli ioni di litio in qualsiasi momento senza che ciò ne riduca la durata utile. Un'interruzione del processo di carica non provoca danni alla batteria.
Non caricare il pacco batteria se la
temperatura ambiente è al di sotto di 10 °C o al di sopra di 40 °C. Se si intende conservare la batteria agli ioni di litio per un periodo prolungato, occorre controllarne periodicamente la carica. La carica ottimale è compresa tra il 50% e l’80%. L’ambiente di stoccaggio deve essere fresco e asciutto e avere una temperatura ambiente compresa fra 0 °C e 50 °C.
CAUTELA!
Staccare sempre la spina dalla presa di rete
prima di rimuovere o inserire il pacco batteria
nell'apparecchio.
1.) Per rimuovere il pacco batteria tasti di sblocco ed estrarre il pacco batteria
dall’apparecchio.
2.) Inserire il pacco batteria rapido .
3.) Inserire la spina nella presa. Il LED di controllo carica rosso
4.) Il LED di controllo carica verde il procedimento di carica è concluso e che il pacco batteria è pronto per l'uso.
5.) Introdurre il pacco batteria
si accende con luce rossa.
, premere i
nel caricabatterie
segnala che
nell'apparecchio.
PBSA 12 D3
Lettura dello stato di carica della batteria
Quando l'apparecchio è acceso le condizioni della batteria, ossia la carica residua, vengono vi­sualizzate sul LED di visualizzazione stato di carica batteria come segue:
IT│MT 
 7
ROSSO / ARANCIONE / VERDE = carica
10a
10a
10a
10a
massima ROSSO / ARANCIONE = carica media ROSSO = carica debole – caricare la batteria
Sostituzione degli utensili
L'avvitatore a batteria è dotato di un arresto del mandrino completamente automatico.
Con motore fermo, la trasmissione viene bloccata per consentire di aprire il mandrino per punte da trapano a serraggio rapido
tramite rotazione
. Dopo aver inserito l'utensile desiderato e aver­lo fissato tramite rotazione del mandrino per punte da trapano
, si può continuare immediatamente con il lavoro. Il blocco del mandrino si disattiva automaticamente con l'avvio del motore (aziona­mento dell'interruttore ON /OFF
).
Trasmissione a 2 velocità
CAUTELA!
Azionare il selettore di velocità
solo quan­do l'apparecchio è fermo, altrimenti l'appa­recchio potrebbe danneggiarsi.
Nella prima velocità (selettore di velocità in posizione: 1)
-1
si ottiene un numero di giri di circa 350 min
e un elevato momento torcente. Questa impostazione è adatta per tutti i lavori di avvitamento.
Nella seconda velocità (selettore di velocità in posizione: 2)
-1
si ottiene un numero di giri di circa 1300 min
per
l'esecuzione di lavori di perforazione.
Rimozione del mandrino per punte da trapano
Per utilizzare la sede della punta , occorre rimuovere il mandrino per punte da trapano a serraggio rapido .
Rimozione del mandrino per punte da trapano:
Afferrare saldamente il mandrino per punte
da trapano a serraggio rapido anteriore.
dalla parte
Tirare, spingere l'anello per mandrino per punte
da trapano
verso il mandrino per punte da trapano a serraggio rapido . A questo punto il mandrino per punte da tra­pano a serraggio rapido è sbloccato e può essere rimosso sfilandolo in avanti.
Inserimento del mandrino per punte da tra­pano a serraggio rapido:
Per inserire nuovamente il mandrino per punte
da trapano a serraggio rapido
, tirare l'anel­lo per mandrino per punte da trapano il mandrino per punte da trapano a serraggio rapido . Nel far questo infilare il mandrino per punte da trapano a serraggio rapido sulla la sede della punta . Rilasciare l'anello per mandrino per punte da trapano innestare il mandrino per punte da trapano a serraggio rapido .
NOTA
Nel caso in cui il mandrino per punte da
trapano a serraggio rapido
non si innestasse automaticamente, ruotare l’anello per mandrino per punte da trapano
Utilizzo della sede della punta
Dopo aver estratto il mandrino per punte da trapa­no a serraggio rapido , è possibile utilizzare la sede della punta .
Inserire una punta idonea nella sede della
punta
.
Spingere quindi la punta fino all'arresto nella
sede
. L’inserimento e il supporto magnetico manten­gono la punta in sede.
Per rimuovere la punta, è sufficiente sfilarla
dalla sede della punta
.
Preselezione del momento torcente / livello di perforazione
Tramite la preselezione del momento torcente si può impostare la forza di rotazione.
Selezionare un livello basso per viti piccole
ovvero materiali morbidi.
verso
per fare
.
8 │ IT
MT
PBSA 12 D3
Selezionare un livello alto per viti grandi, mate-
riali duri, o nell'estrazione di viti.
Per i lavori di perforazione, selezionare il livello
di perforazione impostando la preselezione del momento torcente
Per lavori di trapanatura spingere anche il selet-
tore di marcia
in posizione .
in avanti (posizione: 2).
Messa in funzione
Cambiamento del senso di rotazione / sbloccaggio dell'apparecchio
Sbloccare l'apparecchio e cambiare il senso di
rotazione premendo completamente il commu­tatore del senso di rotazione verso destra o verso sinistra.
Accensione/spegnimento
Accensione:
Per mettere in funzione l'apparecchio, premere
l'interruttore ON / OFF luce di lavoro LED ruttore ON/OFF leggermente o completamen­te premuto. Essa consente in tal modo l'illumina­zione dell'area di lavoro quando l'illuminazione dell'ambiente non è favorevole.
Spegnimento:
per spegnere l'apparecchio, rilasciare l'interrut-
tore ON/OFF
e tenerlo premuto. La
si accende in caso di inter-
.
Consigli e suggerimenti
Suggerimento! Questo è il comporta-
mento corretto.
Prima della messa in funzione, controllare che
l'accessorio per l'avvitamento o la perforazione sia stato inserito correttamente, cioè centrato nel mandrino.
Le punte sono contrassegnate con dimensioni e
forma. In caso di dubbio, controllare prima che il bit entri nella vite senza gioco.
Forza di serraggio:
Viti / bit piccoli possono danneggiarsi se si
imposta un momento torcente o un numero di giri troppo elevato.
Avvitatura rigida (in metallo):
Momenti torcenti particolarmente elevati si
formano ad es. in caso di avvitamento di metalli con l'uso di inserti con chiave a bussola. Sele­zionare un numero di giri inferiore.
Avvitatura morbida (per es. in legno morbido):
Avvitare anche qui con un numero di giri infe-
riore, per ad es. non danneggiare la superficie di legno al contatto con la testa della vite in metallo. Utilizzare un allargatore.
Regolazione del velocità
L'interruttore ON/OFF è provvisto di una regolazione variabile della velocità. Una leggera pressione sull'interruttore ON/OFF velocità bassa. Aumentando la pressione aumenta anche la velocità.
NOTA
Il freno motore provvede a un arresto rapido.
genera una
Attivazione del blocco
Portare il commutatore del senso di rotazione
nella posizione centrale. L'interruttore ON/
OFF è bloccato.
PBSA 12 D3
Nella perforazione di materiali come legno, metallo e altro, tenere assolutamente presen­te quanto segue:
In caso di diametro di perforazione ridotto
utilizzare un alto numero di giri, e in caso di diametro di perforazione più ampio un numero di giri inferiore.
Per i materiali duri scegliere un numero di giri
basso, per i materiali morbidi un numero di giri alto.
Assicurare o fissare (se possibile) il pezzo da
lavorare in un dispositivo di serraggio.
Segnare il punto in cui si desidera perforare
con una punta o un chiodo. Per iniziare a forare selezionare un numero di giri ridotto.
IT│MT 
 9
Estrarre più volte la punta del trapano dal foro
in modo da rimuovere i trucioli o la segatura e per farla aerare.
Perforazione del metallo:
Utilizzare punte da metallo (HSS). Per ottenere
massimi risultati, si consiglia di raffreddare la punta con olio da taglio. La punta in metallo può essere anche utilizzata per perforare la plastica. Perforare dapprima con una punta da Ø 3 mm e poi avvicinarsi al diametro di foratura desiderato.
Perforazione in legno:
Utilizzare una punta da legno con spina di
centraggio, per perforazioni profonde utilizzare una "punta a elica", per diametri di foratura maggiori una punta Forstner. Le viti piccole nel legno morbido possono essere inserite anche senza precedente foratura.
Manutenzione e pulizia
ATTENZIONE! PERICOLO DI LESIONI!
Prima di qualsiasi lavoro sull'appa­recchio, spegnere l'apparecchio e rimuovere la batteria.
L'avvitatore a batteria non necessita di manuten­zione.
L'apparecchio dev'essere sempre pulito, asciutto
e privo di olio o grassi lubrificanti.
Impedire la penetrazione di liquidi all'interno
degli apparecchi.
Per la pulizia dell'alloggiamento, utilizzare un
panno asciutto. Non utilizzare mai benzina, solventi o detergenti in grado di aggredire la plastica.
Se si intende conservare la batteria agli ioni
di litio per un periodo prolungato, occorre controllarne periodicamente la carica. La carica ottimale è compresa tra il 50% e l'80%. L'ambiente ottimale per la conservazione deve essere fresco e asciutto.
NOTA
I pezzi di ricambio non indicati (come ad es.
batteria, interruttore) possono essere ordinati tramite la nostra hotline di assistenza.
Garanzia della Kompernass Handels GmbH
Egregio Cliente, Questo apparecchio ha una garanzia di 3 anni
dalla data di acquisto. Qualora questo prodotto presentasse vizi, Le spettano diritti legali nei con­fronti del venditore del prodotto. La garanzia qui di seguito descritta non costituisce alcun limite a tali diritti legali.
Condizioni di garanzia
Il periodo di garanzia decorre dalla data di acquisto. Si prega di conservare bene lo scontrino di cassa. Quest’ultimo è necessario come prova d’acquisto.
Qualora entro tre anni a partire dalla data d’acquisto del prodotto si presentasse un difetto del materiale o di fabbricazione, provvederemo a nostra discrezione a riparare o a sostituire gratuitamente il prodotto oppure a rimborsare il prezzo d’acquisto. Questa prestazione di garanzia ha come presupposto che l’apparecchio guasto e la prova d’acquisto (scontrino di cassa) vengano presentati entro il termine di tre anni e che si descri­va per iscritto in cosa consiste il difetto e quando si è evidenziato.
Se il vizio rientra nell’ambito della nostra garanzia, il Suo prodotto verrà riparato o sostituito da uno nuovo. Con la riparazione o la sostituzione del pro­dotto non decorre un nuovo periodo di garanzia.
Periodo di garanzia e diritti legali di rivendicazione di vizi
Il periodo di garanzia non viene prolungato da interventi in garanzia. Ciò vale anche per le parti sostituite e riparate. Danni e vizi eventualmente già presenti al momento dell’acquisto devono venire segnalati immediatamente dopo che l’apparec­chio è stato disimballato. Le riparazioni eseguite dopo la scadenza del periodo di garanzia sono a pagamento.
10 │ IT
MT
PBSA 12 D3
Ambito della garanzia
L’apparecchio è stato prodotto con cura secondo severe direttive qualitative e debitamente collauda­to prima della consegna.
La prestazione in garanzia vale per difetti del materiale o di fabbricazione. Questa garanzia non si estende a componenti del prodotto esposti a normale logorio, che possono pertanto essere considerati come componenti soggetti a usura o a danni che si verificano su componenti delicati, come ad es. interruttori, batterie o parti realizzate in vetro.
Questa garanzia decade se il prodotto è stato dan­neggiato oppure utilizzato o sottoposto a interventi di manutenzione in modo non conforme. Per un utilizzo adeguato del prodotto si devono rigorosamente rispettare tutte le istruzioni esposte nel manuale di istruzioni per l’uso. Si devono assolutamente evitare modalità di utilizzo e azioni che il manuale di istruzio­ni per l’uso sconsiglia o da cui esso mette in guardia.
Il prodotto è destinato esclusivamente all’uso do­mestico e non a quello commerciale. La garanzia decade in caso di impiego improprio o mano­missione, uso della forza e interventi non eseguiti dalla nostra filiale di assistenza autorizzata.
Trattamento dei casi di garanzia
Per garantire una rapida evasione della Sua richie­sta, La preghiamo di seguire le seguenti istruzioni:
Tenga a portata di mano per qualsiasi richiesta
lo scontrino di cassa e il codice dell’articolo (per es. IAN12345) come prova di acquisto.
Il codice dell’articolo è riportato sulla targhetta
identificativa o su un’incisione presenti sul pro­dotto, sul frontespizio del manuale di istruzioni (in basso a sinistra) o su un adesivo applicato alla parte posteriore o inferiore del prodotto.
Qualora si presentassero malfunzionamenti o
altri tipi di vizi, contatti innanzitutto il repar­to assistenza clienti qui di seguito indicato telefonicamente o via e-mail.
Una volta che il prodotto è stato registrato
come difettoso, lo può poi spedire a nostro carico, provvedendo ad allegare la prova di acquisto (scontrino di cassa), una descrizione del vizio e l’indicazione della data in cui si è presentato, all’indirizzo del servizio di assisten­za clienti che Le è stato comunicato.
NOTA
In caso di utensili Parkside e Florabest si pre-
ga di spedire esclusivamente l'articolo guasto senza accessori (per es. batteria, valigetta, attrezzi di montaggio, ecc.).
PBSA 12 D3
Sul sito www.lidl-service.com è possibile scaricare questo e molti altri manuali di istruzioni, filmati sui prodotti e software d’installazione.
Con questo codice QR si giunge direttamente al sito dell’assistenza clienti Lidl (www.lidl-service.com) e con la digitazione del codice articolo (IAN) 123456 si può aprire il manuale di istruzioni di proprio interesse.
IT│MT 
 11
Assistenza
AVVERTENZA!
► Fare riparare gli apparecchi dal centro
di assistenza o da un elettricista specia­lizzato e solo con pezzi di ricambio origi­nali. In tal modo si garantisce la sicurezza
dell'apparecchio.
► Fare eseguire sempre la sostituzione
della spina o del cavo dal produttore dell'apparecchio o dal relativo centro di as­sistenza. In tal modo si garantisce la sicurezza
dell'apparecchio.
Assistenza Italia
Tel.: 02 36003201 E-Mail: kompernass@lidl.it
Service Malta
Tel.: 80062230 E-Mail: kompernass@lidl.com.mt
IAN 322702_1901
Importatore
Badi che il seguente indirizzo non è quello del servizio di assistenza clienti. Contatti innanzitutto il servizio di assistenza clienti indicato.
KOMPERNASS HANDELS GMBH BURGSTRASSE 21 44867 BOCHUM GERMANIA www.kompernass.com
Smaltimento
L'imballaggio è costituito da materiali
ecocompatibili che possono essere smaltiti tramite gli appositi centri di raccolta e riciclaggio.
Non smaltire gli elettrodomestici
assieme ai normali rifiuti domestici!
In base alla Direttiva europea 2012/19/EU, gli elettrodomestici usati devono essere raccolti sepa­ratamente e conferiti a un centro per il riciclaggio ecologico.
Non smaltire le batterie assieme ai
normali rifiuti domestici!
Prima dello smaltimento, rimuovere le batterie dall'apparecchio. Le batterie difettose o esauste devono essere rici­clate in base alla direttiva 2006/66/EC. Riconse­gnare il pacco batteria e/o l'apparecchio presso gli appositi centri di raccolta. Per le possibilità di smaltimento relative agli elettroutensili/al pacco batteria usati, informarsi presso il municipio o l'amministrazione comunale di residenza.
Smaltire l‘imballaggio conformemente alle norme di tutela ambientale. Tenere conto dei codici presenti sui vari materiali di imballaggio ed eventualmente separare i materiali effettuando una raccolta differenziata. I materiali di imballaggio presentano codici costituiti da abbreviazioni (a) e numeri (b) con il seguente significato:
1–7: materie plastiche, 20–22: carta e cartone, 80–98: materiali compositi
12 │ IT
MT
Per lo smaltimento del prodotto una volta che ha terminato la sua funzione, informarsi presso l’amministrazione comunale.
PBSA 12 D3
Traduzione della dichiarazione di conformità originale
La Società KOMPERNASS HANDELS GMBH, responsabile della documentazione: nella persona del Sig. Semi Uguzlu, BURGSTR. 21, DE - 44867 BOCHUM, GERMANIA, dichiara con la presente che questo prodotto è conforme alle seguenti norme, documenti normativi e Direttive CE:
Direttiva macchine (2006 / 42 / EC) Direttiva CE bassa tensione
(2014 / 35 / EU) (solo caricabatterie) Compatibilità elettromagnetica (2014 / 30 / EU) Direttiva RoHS (2011 / 65 / EU)*
*Il produttore è il responsabile esclusivo del rilascio di questa dichiarazione di conformità. L'oggetto della dichiarazione sopra descritto soddisfa le prescrizioni della Direttiva 2011/65/EU del Parlamento Europeo e del Consiglio Europeo dell'8giugno 2011 sulla restrizione dell'uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche.
Norme armonizzate utilizzate:
EN 62841-1:2015 EN 62841-2-1:2018 EN 60335-1:2012/A13:2017 EN 60335-2-29:2004/A11:2018 EN 62233:2008 EN 55014-1:2017 EN 55014-2:2015 EN 61000-3-2:2014 EN 61000-3-3:2013 EN 50581:2012
Tipo / denominazione dell'apparecchio: Trapano avvitatore ricaricabile PBSA 12 D3 Anno di produzione: 05 - 2019 Numero di serie: IAN 322702_1901
Bochum, 11.06.2019
Semi Uguzlu
- Direttore qualità ­Con riserva di modifiche tecniche volte al miglioramento del prodotto.
PBSA 12 D3
IT│MT 
 13
Ordinazione di una batteria di ricambio
Se si desidera ordinare una batteria di ricambio per il proprio apparecchio, lo si può fare comodamente via Internet sul sito www.kompernass.com o telefonicamente. Dato che le scorte sono limitate, questo articolo potrebbe esaurirsi entro breve tempo.
NOTA
In alcuni paesi non è possibile ordinare online i pezzi di ricambio. In questo caso, contattare l'hotline
di assistenza.
L’iniziativa promozionale è limitata a una batteria per cliente / apparecchio nonché a un periodo di
due mesi dopo il termine dell’iniziativa. La batteria di ricambio può essere ordinata anche dopo tale data ma a condizioni diverse.
Ordine telefonico
Assistenza Italia
Tel.: 02 36003201 E-Mail: kompernass@lidl.it
Assistenza Malta
Tel.: 80062230 E-Mail: kompernass@lidl.com.mt
Per garantire un’elaborazione rapida dell’ordine, tenere a portata di mano il numero di articolo (ad es. IAN 322702) dell’apparecchio. Il codice di articolo è indicato sulla targhetta di modello nonché sulla pagina di copertina di questo manuale di istruzioni.
14 │ IT
MT
PBSA 12 D3
Contents
Introduction .....................................................16
Intended use ............................................................... 16
Features .................................................................. 16
Package contents ...........................................................16
Technical data ............................................................. 16
General power tool safety warnings ................................17
1. Work area safety ......................................................... 17
2. Electrical safety .......................................................... 17
3. Personal safety ........................................................... 18
4. Power tool use and care ...................................................18
5. Battery tool use and care ................................................... 19
6. Service ................................................................. 19
Safety guidelines for cordless screw drivers ....................................... 19
Original accessories/auxiliary equipment ........................................ 20
Safety guidelines for battery chargers ........................................... 20
Before use ......................................................20
Removing/charging/inserting the battery pack .................................... 20
Checking the battery charge level .............................................. 20
Changing tools ............................................................. 21
2-speed gearbox ........................................................... 21
Removing the chuck .........................................................21
Using the bit adapter ........................................................ 21
Torque selection ring/drill setting ............................................... 21
Use ............................................................21
Change direction of rotation/unlock appliance .................................... 21
Switching on and off ........................................................21
Adjusting the rotational speed .................................................22
Activate lock ............................................................... 22
Tips and tricks ..............................................................22
Maintenance and cleaning .........................................22
Kompernass Handels GmbH warranty ..............................23
Service .........................................................24
Importer .......................................................24
Disposal ........................................................24
Translation of the original Conformity Declaration .....................25
Ordering a replacement battery ....................................26
Telephone ordering .........................................................26
PBSA 12 D3
GB│MT 
15
CORDLESS DRILL
10a
T2A
PBSA 12 D3
Introduction
Congratulations on the purchase of your new appli­ance. You have chosen a high-quality product. The operating instructions are part of this product. They contain important information about safety, usage and disposal. Before using the product, please familiarise yourself with all operating and safety instructions. Use the product only as described and for the range of applications specified. Please also pass these operating instructions on to any future owner.
Intended use
This appliance is designed for screwing and drilling into wood, plastic and metal. Use this product only as described and for the areas of applications specified. Any other usage of or modification to the appliance is deemed to be improper and carries a significant risk of accidents. The manufacturer accepts no responsibility for damage(s) attribut­able to misuse. This appliance is not intended for commercial use.
Features
Speed selector Battery LED (charge level indicator) Rotational direction switch/lock ON/OFF switch Soft grip Battery pack Release button for the battery pack LED working light Torque selection ring/drill setting Quick-release chuck Chuck ring Bit adapter Bit holder
Figure A:
Red charge control LED Green charge control LED
Charger
Package contents
1 cordless drill 1 high-speed battery charger 1 battery pack 1 carrying case 1 set of operating instructions
Technical data
Cordless drill: PBSA 12 D3:
Rated voltage: 12 V Rated idle speed: 1st gear: n
Chuck clamping range
Max. drill diameter: Steel: 8 mm
Battery pack: PAPK 12 A2:
Type: LITHIUM ION Rated voltage: 12 V
Cells: 3 Capacity: 2000 mAh (24 Wh)
High-speed battery charger: PLGK 12 A1:
INPUT:
Rated voltage: 220 - 240 V ~, 50-60 Hz
Rated power consumption: 50 W
Fuse (internal): 2 A
OUTPUT:
Rated voltage: 12 V Rated current: 2400 mA Charging time: approx. 60 min
Protection class: II /
: max. Ø 10 mm
(DC)
0–350 rpm
2nd gear: n0 0–1300 rpm
Wood: 20 mm
(AC)
0
(DC)
(DC)
(double insulation)
16 │ GB
MT
PBSA 12 D3
Noise emission value:
Noise measurement value determined in accor­dance with EN 62841. The A-rated noise level of the power tool is typically:
Sound pressure level: L Uncertainty K: K Sound power level: L Uncertainty K: K
= 71.1 dB(A)
PA
= 3 dB
PA
= 82.1 dB(A)
WA
= 3 dB
WA
Vibration emission value:
Total vibration values (vector total of three direc­tions) determined in accordance with EN 62841:
Drilling in metal: Vibration emission value
= 1.987 m/s2
a
h,D
Uncertainty K = 1.5 m/s
2
Screwing without impact: Vibration emission value
a
= 0.781 m/s2
h
Uncertainty K = 1.5 m/s
2
NOTE
The vibration emission values and the noise
emission values given in these instructions have been measured in accordance with a standardised test procedure and can be used for comparison of the power tool with another tool.
The specified total vibration values and the
noise emission values can also be used to make a provisional load estimate.
WARNING!
Depending on the manner in which the power
tool is being used, and in particular the kind of workpiece that is being worked, the vibration and noise emission values can deviate from the values given in these instructions during actual use of the power tool.
Try to keep the load as low as possible.
Measures to reduce the vibration load are, e.g. wearing gloves and limiting the working time. Wherein all states of operation must be included (e.g. times when the power tool is switched off and times where the power tool is switched on but running without load).
General power tool safety warnings
WARNING!
► Read all safety warnings, instructions, illust-
rations and specifications provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term „power tool“ in the warnings refers to your mains-operated (corded) power tool or bat­tery-operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or ground-
ed surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
PBSA 12 D3
GB│MT 
17
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduc-
es the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and
use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools
with your finger on the switch or energising power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
Protective equipment such
h) Do not let familiarity gained from frequent
use of tools allow you to become complacent and ignore tool safety principles. A careless
action can cause severe injury within a fraction of a second.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can­not be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detacha­ble, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool acci­dentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired be­fore use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak­ing into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
18 │ GB
MT
PBSA 12 D3
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for safe handling and control of the tool in unex­pected situations.
5. Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire when used with another battery pack.
b) Use power tools only with specifically desig-
nated battery packs. Use of any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejec-
ted from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause
irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire or temperature above 130 °C (265°F) may cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the temperature range specified in the instruc­tions. Charging improperly or at temperatures
outside the specified range may damage the battery and increase the risk of fire.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable batteries!
Protect the rechargeable battery from
heat, for example from continuous exposure to sunlight, fire, water and moisture. There is a risk of explosion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace­ment parts. This will ensure that the safety of
the power tool is maintained.
b) Never service damaged battery packs. Service
of battery packs should only be performed by the manufacturer or authorized service providers.
Safety guidelines for cordless screw drivers
Safety instructions for all work
WARNING!
■ Hold the power tool only by the insulated
handles when you are carrying out work in which the accessory tool may come into contact with concealed power cables or the tool’s own power cord. Contact between
the screw or attached tool and a live wire may cause exposed metal parts of the power tool to become live and give the operator an electric shock.
Safety information for using long drill bits
■ Do not use a higher rotational speed than
the maximum permissible speed. At higher
speeds, the drill bit can bend slightly if allowed to turn freely without being in contact with the workpiece and this can lead to injuries.
■ Always start drilling at a low speed and with
the drill bit in contact with the workpiece. At
higher speeds, the drill bit can bend slightly if allowed to turn freely without being in contact with the workpiece and this can lead to injuries.
PBSA 12 D3
GB│MT 
19
■ Do not exert excessive pressure and only
along the length of the drill bit (no lateral pressure). Drill bits can bend and break which
can lead to a loss of control and injuries.
Original accessories/auxiliary equipment
Use only the accessories and additional equip-
ment that are specified in the operating instruc­tions and are compatible with the appliance.
Safety guidelines for battery chargers
This appliance may be used by chil-
dren aged 8 years and above and by persons with limited physical, sensory or mental capabilities or lack of experience and knowledge, provided that they are under super­vision or have been told how to use the appliance safely and are aware of the potential risks. Do not allow children to use the appliance as a toy. Cleaning and user maintenance tasks may not be carried out by children unless they are supervised.
The charger is suitable for
indoor use only.
WARNING!
To avoid potential risks, damaged mains cables
should be replaced by the manufacturer, their customer service department or a similarly qualified person.
ATTENTION!
This charger can only charge the following
batteries: PAPK 12 A1 / PAPK 12 A2, PAPK 12 B1.
A current list of battery compatibility can
be found at www.lidl.de/akku.
Before use
Removing/charging/inserting the battery pack
NOTE
The battery is partially charged. Ideally, fully
charge the battery before use. You can charge the lithium-ion battery at any time without shortening its service life. Interrupting the charging process does not damage the battery.
Never charge the battery pack if the ambient
temperature is below 10°C or above 40°C. If a lithium-ion battery is to be stored for an extended period, the charge level should be checked regularly. The optimum charge level is between 50% and 80%. The storage climate should be cool and dry and the ambient temperature should be between 0°C and 50°C.
CAUTION!
Always unplug the appliance before you
remove the battery pack the battery pack to the charger.
1.) To remove the battery pack release button and pull the battery pack out of the appliance.
2.) Insert the battery pack charger .
3.) Insert the power plug into the socket. The red charge indicator LED
4.) The green charge indicator LED that the charging process is complete and the battery pack is ready for use.
5.) Push the battery pack ance.
Checking the battery charge level
When the appliance is switched on, the remaining charge will be shown on the battery LED as follows: RED/ORANGE/GREEN = maximum charge RED/ORANGE = medium charge RED = low charge – charge the battery
from or connect
, press the
into the battery
lights up.
indicates
back into the appli-
20 │ GB
MT
PBSA 12 D3
Changing tools
10a
10a
10a
10a
Your cordless screwdriver has a fully automatic spindle lock .
When the motor is stopped, the power train locks so that the quick-release chuck
can be opened by turning it . After you have attached the desired tool and tightened it by turning the chuck
, you can continue working. The spindle lock is automatically released when the motor starts (ON/OFF switch pressed).
2-speed gearbox
CAUTION!
Operate the speed selector
only when the appliance is at a standstill. Otherwise the appliance can be damaged.
In first gear (speed selector
in position: 1)
you can reach a speed of approx. 350 rpm and a high torque. This setting is suitable for all screwing jobs.
In second gear (speed selector
in position: 2)
you can reach a speed of approx. 1300 rpm for carrying out drilling work.
Removing the chuck
If you want to use the bit adapter , you must remove the quick-release chuck
.
NOTE
If the quick-release chuck
does not automatically click into place, turn the chuck ring
.
Using the bit adapter
After removing the quick release chuck , you can use the bit adapter .
Insert a suitable bit into the bit adapter Push the bit into the bit adapter
.
as far as the stop. The guidance and the magnetic holder keep the bit firmly in place.
Pull the bit out of the bit adapter
.
Torque selection ring/drill setting
You can set the torque using the torque selection ring .
Select a low level for small screws or soft
materials.
Select a high level for large screws, hard materi-
als or removing screws.
Select the drill setting for drilling work by
adjusting the torque selection ring position
Push the speed selector
.
forward for drilling
work (position: 2).
to the
Removing the chuck:
Hold the quick-release chuck
front.
Pull/push the chuck ring
the quick-release chuck . The quick-release chuck is now unlocked and can be removed towards the front.
Attaching the quick-release chuck:
To replace the quick-release chuck
chuck ring
towards the quick-release chuck
. Push the quick-release chuck over the bit
adapter
. Let go of the chuck ring
the quick-release chuck into place.
PBSA 12 D3
firmly from the
in the direction of
, pull the
to click
Use
Change direction of rotation/unlock appliance
Unlock the appliance and change the direction
of rotation by pressing the rotation direction switch
Switching on and off
Switching on:
To start the appliance, press the ON/OFF
switch ing light lights up when the ON/OFF switch
illumination of the work area in poor lighting conditions.
towards the left or right.
and keep it pressed in. The LED work-
is depressed lightly or fully. This provides
GB│MT 
21
Switching off:
Release the ON/OFF switch
appliance.
to switch off the
Adjusting the rotational speed
The ON/OFF switch has a variable speed con­trol. Press the ON/OFF switch speed. Increasing the pressure increases the speed.
NOTE
The integrated motor brake ensures rapid
stoppage.
lightly for a low
Activate lock
Push the rotation direction switch into the
middle position. The ON/OFF switch is blocked.
Tips and tricks
Tip! This symbol indicates proper behaviour.
When drilling in wood, metal and other mate­rials, observe the following:
Use a high speed for drill bits with a small
diameter and a low speed for drill bits with a large diameter.
Select a low speed for hard materials and a
high speed for soft materials.
Secure or fasten the workpiece in a clamp or
vice (if possible).
Mark the spot where you want to drill using a
centre punch or nail. Select a low rotational speed when starting.
Pull the rotating drill bit from the hole repeatedly
to remove dust and chips and clear the hole.
Drilling in metal:
Use a metal drill (HSS). For optimum results,
cool the drill bit with cutting oil. Metal drill bits can also be used to drill into plastics. Start with a 3 mm diameter drill bit and then increase the size until the desired hole diameter is achieved.
Before operating the appliance, check whether
the screw or drill bit is correctly positioned, i.e. centred in the drill chuck.
Screw bits are labelled according to their di-
mensions and their shape. If you are uncertain, always check whether the bit fits tightly in the screw head without any free play.
Torque:
Smaller screws/bits can be damaged if you set
the torque or rotational speed too high.
Hard screw joints (in metal):
Particularly high torques occur, for example, in
metal screw joints made using drive sockets. Select a low rotational speed.
Soft screw joints (e.g. in soft wood):
Again, use a low rotational speed, for example
to avoid damaging the surface of the wood on contact with the screw head. Use a countersink.
22 │ GB
MT
Drilling in wood:
Use a wood drill with a lathe centre; for deep
holes, use an auger bit; for large-diameter holes, use a Forstner bit. Small screws can be screwed directly into soft wood.
Maintenance and cleaning
WARNING! RISK OF INJURY!
Always switch the appliance off and remove the battery before carrying out any work on the appliance.
The cordless screwdriver is maintenance-free.
The appliance must always be kept clean, dry
and free from oil or grease.
Never allow liquids to get into the appliance.
Use a soft, dry cloth to clean the housing.
Never use petrol, solvents or cleansers which can damage plastic.
If a lithium-ion battery is to be stored for an
extended period, the charge level should be checked regularly. The optimum charge level is between 50% and 80%. The optimum storage environment is cool and dry.
PBSA 12 D3
NOTE
Replacement parts not listed (such as batter-
ies, switches) can be ordered via our service hotline.
Kompernass Handels GmbH warranty
Dear Customer, This appliance has a 3-year warranty valid from
the date of purchase. If this product has any faults, you, the buyer, have certain statutory rights. Your statutory rights are not restricted in any way by the warranty described below.
Warranty conditions
The warranty period starts on the date of purchase. Please keep your receipt in a safe place. This will be required as proof of purchase.
If any material or manufacturing fault occurs within three years of the date of purchase of the product, we will either repair or replace the product for you or refund the purchase price (at our discretion). This warranty service requires that you present the defective appliance and the proof of purchase (re­ceipt) within the three-year warranty period, along with a brief written description of the fault and of when it occurred.
If the defect is covered by the warranty, your pro­duct will either be repaired or replaced by us. The repair or replacement of a product does not signify the beginning of a new warranty period.
Warranty period and statutory claims for defects
The warranty period is not prolonged by repairs effected under the warranty. This also applies to replaced and repaired components. Any damage and defects present at the time of purchase must be reported immediately after unpacking. Repairs carried out after expiry of the warranty period shall be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accord­ance with strict quality guidelines and inspected meticulously prior to delivery.
The warranty covers material faults or production faults. The warranty does not extend to product parts subject to normal wear and tear or to fragile parts which could be considered as consumable parts such as switches, batteries or parts made of glass.
The warranty does not apply if the product has been damaged, improperly used or improper­ly maintained. The directions in the operating instructions for the product regarding proper use of the product are to be strictly followed. Uses and actions that are discouraged in the operating instructions or which are warned against must be avoided.
This product is intended solely for private use and not for commercial purposes. The warranty shall be deemed void in cases of misuse or improper handling, use of force and modifications / repairs which have not been carried out by one of our authorised Service centres.
Warranty claim procedure
To ensure quick processing of your case, please observe the following instructions:
Please have the till receipt and the item number
(e.g.IAN12345) available as proof of purchase.
You will find the item number on the type plate
on the product, an engraving on the product, on the front page of the operating instructions (below left) or on the sticker on the rear or bottom of the product.
If functional or other defects occur, please
contact the service department listed either by telephone or by e-mail.
You can return a defective product to us free of
charge to the service address that will be pro­vided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.
NOTE
For Parkside and Florabest tools, please send
us only the defective item without the acces­sories (e.g. battery, storage case, assembly tools, etc.).
PBSA 12 D3
GB│MT 
23
You can download these instructions along with many other manuals, product videos and installation software at www.lidl-service.com.
This QR code will take you directly to the Lidl service page (www.lidl-service.com) where you can open your operating instructions by entering the item number (IAN) 123456.
Disposal
The packaging is made from environmen­tally friendly material and can be disposed of at your local recycling plant.
Do not dispose of power tools in your normal domestic waste!
Service
WARNING!
► Have the power tool repaired by the service
centre or a qualified electrician and only using genuine replacement parts. This will
ensure that the safety of the appliance is maintained.
► Always ensure that the power plug or the
mains cable is replaced only by the man­ufacturer of the appliance or its customer service. This will ensure that the safety of the
appliance is maintained.
Service Great Britain
Tel.: 0800 404 7657 E-Mail: kompernass@lidl.co.uk
Service Malta
Tel.: 80062230 E-Mail: kompernass@lidl.com.mt
IAN 322702_1901
Importer
Please note that the following address is not the service address. Please use the service address provided in the operating instructions.
KOMPERNASS HANDELS GMBH BURGSTRASSE 21 44867 BOCHUM GERMANY www.kompernass.com
European Directive 2012/19/EU requires that worn-out power tools be collected separately and recycled in an environmentally compatible manner.
Do not dispose of batteries in your normal household waste!
Before disposal, remove the batteries from the appliance. Defective or worn-out rechargeable batteries must be recycled according to Directive 2006/66/EC. Take the battery pack and/or appliance to a near­by collection facility. Please consult your local authorities regarding suitable disposal of worn out power tools/battery packs.
Dispose of the packaging in an environmentally friendly manner. Note the labelling on the packaging and separate the packaging material components for disposal if necessary. The packaging material is labelled with abbreviations (a) and numbers (b) with the following meanings:
1–7: Plastics, 20–22: Paper and cardboard, 80–98: Composites.
Your local community or municipal authorities can provide information on how to dispose of the worn-out product.
24 │ GB
MT
PBSA 12 D3
Translation of the original Conformity Declaration
We, KOMPERNASS HANDELS GMBH, document officer: Mr Semi Uguzlu, BURGSTR. 21, DE - 44867 BOCHUM, GERMANY, hereby declare that this product complies with the following standards, normative documents and EC directives:
Machinery Directive (2006/42/EC) EC Low Voltage Directive
(2014/35/EU) (only charger) EMC (Electromagnetic Compatibility) (2014/30/EU) RoHS Directive (2011/65/EU)*
*The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the declaration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic appliances.
Applied harmonised standards:
EN 62841-1:2015 EN 62841-2-1:2018 EN 60335-1:2012/A13:2017 EN 60335-2-29:2004/A11:2018 EN 62233:2008 EN 55014-1:2017 EN 55014-2:2015 EN 61000-3-2:2014 EN 61000-3-3:2013 EN 50581:2012
Type/appliance designation: Cordless drill PBSA 12 D3 Year of manufacture: 05 - 2019 Serial number: IAN 322702_1901
Bochum, 11.06.2019
Semi Uguzlu
- Quality Manager ­We reserve the right to make technical changes in the context of further product development.
PBSA 12 D3
GB│MT 
25
Ordering a replacement battery
If you want to order a replacement battery for your appliance, you can do so easily via the Internet on www.kompernass.com or by telephone. Due to limited stocks, this item may sell out in a relatively short time.
NOTE
Online ordering of replacement parts might not be possible in some countries. In this is the case,
please contact the Service hotline.
The promotion is limited to one battery per customer/appliance and also to a timeline of two months
after the promotion period. Thereafter, the replacement battery can be ordered as a replacement part under other conditions.
Telephone ordering
Service Great Britain
Tel.: 0800 404 7657 E-Mail: kompernass@lidl.co.uk
Service Malta
Tel.: 80062230 E-Mail: kompernass@lidl.com.mt
To ensure fast processing of your order, have the article number of your appliance to hand (e.g. IAN 322702) in case of questions. The article number can be found on the type plate or the title page of these instructions.
26 │ GB
MT
PBSA 12 D3
Inhaltsverzeichnis
Einleitung .......................................................28
Bestimmungsgemäßer Gebrauch ............................................... 28
Ausstattung ................................................................ 28
Lieferumfang ............................................................... 28
Technische Daten ...........................................................28
Allgemeine Sicherheitshinweise fürElektrowerkzeuge ..................29
1. Arbeitsplatzsicherheit ...................................................... 29
2. Elektrische Sicherheit ...................................................... 30
3. Sicherheit von Personen ....................................................30
4. Verwendung und Behandlung des Elektrowerkzeugs .............................31
5. Verwendung und Behandlung des Akkuwerkzeugs ...............................31
6. Service ................................................................. 32
Sicherheitshinweise für Bohrschrauber ........................................... 32
Originalzubehör / -zusatzgeräte ............................................... 32
Sicherheitshinweise für Ladegeräte ............................................. 33
Vor der Inbetriebnahme ..........................................33
Akku-Pack entnehmen /laden /einsetzen ......................................... 33
Akkuzustand ablesen ........................................................33
Werkzeuge wechseln ........................................................34
2-Gang Getriebe ........................................................... 34
Bohrfutter abnehmen ........................................................34
Bitaufnahme benutzen ....................................................... 34
Drehmomentvorwahl / Bohrstufe ...............................................34
Inbetriebnahme .................................................35
Drehrichtung umschalten/Gerätentriegeln .......................................35
Ein- / ausschalten ...........................................................35
Drehzahl einstellen .......................................................... 35
Sperre aktivieren ...........................................................35
Tipps und Tricks ............................................................35
Wartung und Reinigung ...........................................36
Garantie der Kompernaß Handels GmbH ............................36
Service .........................................................37
Importeur ......................................................38
Entsorgung .....................................................38
Original-Konformitätserklärung ....................................39
Ersatz Akku Bestellung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Telefonische Bestellung ....................................................... 40
PBSA 12 D3
DE│AT│CH 
 27
AKKU-BOHRSCHRAUBER
10a
T2A
PBSA 12 D3
Einleitung
Wir beglückwünschen Sie zum Kauf Ihres neuen Gerätes. Sie haben sich damit für ein hochwertiges Produkt entschieden. Die Bedienungsanleitung ist Teil dieses Produkts. Sie enthält wichtige Hinweise für Sicherheit, Gebrauch und Entsorgung. Machen Sie sich vor der Benutzung des Produkts mit allen Bedien­und Sicherheitshinweisen vertraut. Benutzen Sie das Produkt nur wie beschrieben und für die angegebe­nen Einsatzbereiche. Händigen Sie alle Unterlagen bei Weitergabe des Produkts an Dritte mit aus.
Bestimmungsgemäßer Gebrauch
Dieses Gerät ist zum Bohren und Schrauben in Holz, Kunststoff und Metall bestimmt. Benutzen Sie das Gerät nur wie beschrieben und für die ange­gebenen Einsatzbereiche. Jede andere Verwen­dung oder Veränderung des Gerätes gilt als nicht bestimmungsgemäß und birgt erhebliche Unfallge­fahren. Für aus bestimmungswidriger Verwendung entstandene Schäden übernimmt der Hersteller keine Haftung. Nicht für den gewerblichen Einsatz bestimmt.
Ausstattung
Gangwahlschalter Akku-LED (Zustandsanzeige) Drehrichtungsumschalter / Sperre EIN- / AUS-Schalter Softgriff Akku-Pack Taste zur Entriegelung des Akku-Packs LED-Arbeitsleuchte Vorwahl Drehmoment / Bohrstufe Schnellspannbohrfutter Bohrfutterring Bitaufnahme Bithalter
Abbildung A:
Rote Ladekontroll-LED Grüne Ladekontroll-LED
Ladegerät
Lieferumfang
1 Akku-Bohrschrauber 1 Akku-Schnellladegerät 1 Akku-Pack 1 Tragekoffer 1 Bedienungsanleitung
Technische Daten
Akku-Bohrschrauber: PBSA 12 D3:
Bemessungsspannung: 12 V Bemessungs-
Leerlaufdrehzahl: 1. Gang: n
Bohrfutterspann­bereich : max. Ø 10 mm
Max. Bohrdurchmesser: Stahl: 8 mm
Akku-Pack: PAPK 12 A2:
Typ: LITHIUM-IONEN Bemessungsspannung: 12 V
Zellen: 3 Kapazität: 2000 mAh (24 Wh)
Akku-Schnellladegerät: PLGK 12 A1
EINGANG / Input:
Bemessungsspannung: 220 – 240 V ~, 50-60 Hz
Bemessungsaufnahme: 50 W Sicherung (innen): 2 A
AUSGANG / Output:
Bemessungsspannung: 12 V Bemessungsstrom: 2400 mA Ladedauer: ca. 60 min
Schutzklasse: II /
(Gleichstrom)
0 - 350 min
2. Gang: n0 0 - 1300 min
0
Holz: 20 mm
(Gleichstrom)
(Wechselspannung)
(Gleichstrom)
(Doppelisolierung)
-1
-1
28 │ DE
│AT│
CH
PBSA 12 D3
Geräuschemissionswert:
Messwert für Geräusch ermittelt entsprechend EN 62841. Der A-bewertete Geräuschpegel des Elektrowerkzeugs beträgt typischerweise:
Schalldruckpegel: L Unsicherheit K: K Schallleistungspegel: L Unsicherheit K: K
= 71,1 dB (A)
PA
= 3 dB
PA
= 82,1 dB (A)
WA
= 3 dB
WA
Schwingungsemissionswert:
Schwingungsgesamtwerte (Vektorsumme dreier Richtungen) ermittelt entsprechend EN 62841:
Bohren in Metall: Schwingungsemissionswert
= 1,987 m/s2
a
h,D
Unsicherheit K = 1,5 m/s
2
Schrauben ohne Schlag: Schwingungsemissionswert
a
= 0,781 m/s2
h
Unsicherheit K = 1,5 m/s
2
HINWEIS
Die angegebenen Schwingungsgesamtwerte
und die angegebenen Geräuschemission­swerte sind nach einem genormten Prüfver­fahren gemessen worden und können zum Vergleich eines Elektrowerkzeugs mit einem anderen verwendet werden.
Die angegebenen Schwingungsgesamtwerte
und die angegebenen Geräuschemission­swerte können auch zu einer vorläufigen Ein­schätzung der Belastung verwendet werden.
WARNUNG!
Die Schwingungs- und Geräuschemissionen
können während der tatsächlichen Benutzung des Elektrowerkzeugs von den Angabewerten abweichen, abhängig von der Art und Weise, in der das Elektrowerkzeug verwendet wird, insbesondere, welche Art von Werkstück bearbeitet wird.
Versuchen Sie, die Belastung so gering wie
möglich zu halten. Beispielhafte Maßnahmen zur Verringerung der Vibrationsbelastung sind das Tragen von Handschuhen beim Ge
­brauch des Werkzeugs und die Begrenzung der Arbeitszeit. Dabei sind alle Anteile des Betriebszyklus zu berücksichtigen (beispiels­weise Zeiten, in denen das Elektrowerkzeug abgeschaltet ist, und solche, in denen es zwar eingeschaltet ist, aber ohne Belastung läuft).
Allgemeine
Sicherheitshinweise fürElektrowerkzeuge
WARNUNG!
► Lesen Sie alle Sicherheitshinweise, Anwei-
sungen, Bebilderungen und technischen Daten, mit denen dieses Elektrowerkzeug versehen ist. Versäumnisse bei der Einhaltung
der nachfolgenden Anweisungen können elektrischen Schlag, Brand und/oder schwere Verletzungen verursachen.
Bewahren Sie alle Sicherheitshinweise und Anweisungen für die Zukunft auf.
Der in den Sicherheitshinweisen verwendete Begriff „Elektrowerkzeug“ bezieht sich auf netzbetriebene Elektrowerkzeuge (mit Netzleitung) und auf akku­betriebene Elektrowerkzeuge (ohne Netzleitung).
PBSA 12 D3
1. Arbeitsplatzsicherheit
a) Halten Sie Ihren Arbeitsbereich sauber und
gut beleuchtet. Unordnung und unbeleuchtete
Arbeitsbereiche können zu Unfällen führen.
DE│AT│CH 
 29
b) Arbeiten Sie mit dem Elektrowerkzeug nicht
in explosionsgefährdeter Umgebung, in der sich brennbare Flüssigkeiten, Gase oder Stäube befinden. Elektrowerkzeuge erzeugen
Funken, die den Staub oder die Dämpfe entzün­den können.
c) Halten Sie Kinder und andere Personen wäh-
rend der Benutzung des Elektrowerkzeugs fern. Bei Ablenkung können Sie die Kontrolle
über das Elektrowerkzeug verlieren.
2. Elektrische Sicherheit
a) Der Anschlussstecker des Elektrowerkzeugs
muss in die Steckdose passen. Der Stecker darf in keiner Weise verändert werden. Verwenden Sie keine Adapterstecker gemein­sam mit schutzgeerdeten Elektrowerkzeugen.
Unveränderte Stecker und passende Steckdo­sen verringern das Risiko eines elektrischen Schlages.
b) Vermeiden Sie Körperkontakt mit geerdeten
Oberflächen wie von Rohren, Heizungen, Herden und Kühlschränken. Es besteht ein
erhöhtes Risiko durch elektrischen Schlag, wenn Ihr Körper geerdet ist.
c) Halten Sie Elektrowerkzeuge von Regen
oder Nässe fern. Das Eindringen von Wasser in ein Elektrowerkzeug erhöht das Risiko eines elektrischen Schlages.
d) Zweckentfremden Sie die Anschlussleitung
nicht, um das Elektrowerkzeug zu tragen, aufzuhängen oder um den Stecker aus der Steckdose zu ziehen. Halten Sie die Anschluss­leitung fern von Hitze, Öl, scharfen Kanten oder sich bewegenden Teilen. Beschädigte
oder verwickelte Anschlussleitungen erhöhen das Risiko eines elektrischen Schlages.
e) Wenn Sie mit einem Elektrowerkzeug im
Freien arbeiten, verwenden Sie nur Verlän­gerungsleitungen, die auch für den Außenbe­reich geeignet sind. Die Anwendung einer für
den Außenbereich geeigneten Verlängerungs­leitung verringert das Risiko eines elektrischen Schlages.
f) Wenn der Betrieb des Elektrowerkzeugs in
feuchter Umgebung nicht vermeidbar ist, ver­wenden Sie einen Fehlerstromschutzschalter.
Der Einsatz eines Fehlerstromschutzschalters ver­mindert das Risiko eines elektrischen Schlages.
3. Sicherheit von Personen
a) Seien Sie aufmerksam, achten Sie darauf,
was Sie tun, und gehen Sie mit Vernunft an die Arbeit mit einem Elektrowerkzeug. Benutzen Sie kein Elektrowerkzeug, wenn Sie müde sind oder unter dem Einfluss von Drogen, Alkohol oder Medikamenten stehen.
Ein Moment der Unachtsamkeit beim Gebrauch des Elektrowerk zeugs kann zu ernsthaften Verletzungen führen.
ragen Sie persönliche Schutzausrüstung und
b) T
immer eine Schutzbrille. Das Tragen persönlicher
Schutzausrüstung, wie Staubmaske, rutschfeste Sicherheitsschuhe, Schutzhelm oder Gehörschutz, je nach Art und Einsatz des Elektrowerkzeugs, verringert das Risiko von Verletzungen.
c) Vermeiden Sie eine unbeabsichtigte
Inbetrieb nahme. Vergewissern Sie sich, dass das Elektrowerkzeug ausgeschaltet ist, bevor Sie es an die Stromversorgung und / oder den Akku anschließen, es aufnehmen oder tragen. Wenn Sie beim Tragen des Elektrowerk-
zeugs den Finger am Schalter haben oder das Elektrowerkzeug eingeschaltet an die Strom­versorgung anschließen, kann dies zu Unfällen führen.
d) Entfernen Sie Einstellwerkzeuge oder Schrau-
benschlüssel, bevor Sie das Elektrowerkzeug einschalten. Ein Werkzeug oder Schlüssel, der
sich in einem drehenden Teil des Elektrowerk­zeugs befindet, kann zu Verletzungen führen.
e) Vermeiden Sie eine abnormale Körperhal-
tung. Sorgen Sie für einen sicheren Stand und halten Sie jederzeit das Gleichgewicht.
Dadurch können Sie das Elektrowerkzeug in unerwarteten Situationen besser kontrollieren.
30 │ DE
│AT│
CH
PBSA 12 D3
f) Tragen Sie geeignete Kleidung. Tragen Sie
keine weite Kleidung oder Schmuck. Halten Sie Haare und Kleidung fern von sich bewe­genden Teilen. Lockere Kleidung, Schmuck
oder lange Haare können von sich bewegen­den Teilen erfasst werden.
g) Wenn Staubabsaug- und -auffangeinrich-
tungen montiert werden können, sind diese anzuschließen und richtig zu verwenden.
Die Verwendung einer Staubabsaugung kann Gefährdungen durch Staub verringern.
h) Wiegen Sie sich nicht in falscher Sicherheit
und setzen Sie sich nicht über die Sicherheits­regeln für Elektrowerkzeuge hinweg, auch wenn Sie nach vielfachem Gebrauch mit dem Elektrowerkzeug vertraut sind. Achtloses
Handeln kann binnen Sekundenbruchteilen zu schweren Verletzungen führen.
4. Verwendung und Behandlung des Elektrowerkzeugs
a) Überlasten Sie das Elektrowerkzeug nicht.
Verwenden Sie für Ihre Arbeit das dafür bestimmte Elektrowerkzeug. Mit dem passen-
den Elektrowerkzeug arbeiten Sie besser und sicherer im angegebenen Leistungsbereich.
b) Benutzen Sie kein Elektrowerkzeug, dessen
Schalter defekt ist. Ein Elektrowerkzeug, das sich nicht mehr ein- oder ausschalten lässt, ist gefährlich und muss repariert werden.
c) Ziehen Sie den Stecker aus der Steckdose
und / oder entfernen Sie den abnehmba­ren Akku, bevor Sie Geräteeinstellungen vornehmen, Einsatzwerkzeugteile wechseln oder das Elektrowerkzeug weglegen. Diese
Vorsichtsmaßnahme verhindert den unbeabsich­tigten Start des Elektrowerkzeugs.
d) Bewahren Sie unbenutzte Elektrowerkzeuge
außerhalb der Reichweite von Kindern auf. Lassen Sie keine Personen das Elektrowerk­zeug benutzen, die mit diesem nicht vertraut sind oder diese Anweisungen nicht gelesen haben. Elektrowerkzeuge sind gefährlich, wenn
sie von unerfahrenen Personen benutzt werden.
e) Pflegen Sie Elektrowerkzeuge und Einsatz-
werkzeug mit Sorgfalt. Kontrollieren Sie, ob bewegliche Teile einwandfrei funktionieren und nicht klemmen, ob Teile gebrochen oder so beschädigt sind, dass die Funktion des Elektrowerkzeugs beeinträchtigt ist. Lassen Sie beschädigte Teile vor dem Einsatz des Elektrowerkzeuges reparieren. Viele Unfälle
haben ihre Ursache in schlecht gewarteten Elektrowerkzeugen.
f) Halten Sie Schneidwerkzeuge scharf und
sauber. Sorgfältig gepflegte Schneidwerkzeuge mit scharfen Schneidkanten verklemmen sich weniger und sind leichter zu führen.
g) Verwenden Sie Elektrowerkzeug, Einsatz-
werkzeug, Einsatzwerkeuge usw. entspre­chend diesen Anweisungen. Berücksichtigen Sie dabei die Arbeitsbedingungen und die auszuführende Tätigkeit. Der Gebrauch von
Elektrowerkzeugen für andere als die vorge­sehenen Anwendungen kann zu gefährlichen Situationen führen.
h) Halten Sie Griffe und Griffflächen trocken,
sauber und frei von Öl und Fett. Rutschige Griffe und Griffflächen erlauben keine sichere Bedienung und Kontrolle des Elektrowerkzeugs in unvorhergesehenen Situationen.
5. Verwendung und Behandlung des Akkuwerkzeugs
a) Laden Sie die Akkus nur mit Ladegeräten auf,
die vom Hersteller empfohlen werden. Durch
ein Ladegerät, das für eine bestimmte Art von Akkus geeignet ist, besteht Brandgefahr, wenn es mit anderen Akkus verwendet wird.
b) Verwenden Sie nur die dafür vorgesehenen
Akkus in den Elektrowerkzeugen. Der Ge­brauch von anderen Akkus kann zu Verletzun­gen und Brandgefahr führen.
c) Halten Sie den nicht benutzten Akku fern von
Büroklammern, Münzen, Schlüsseln, Nägeln, Schrauben oder anderen kleinen Metall­gegenständen, die eine Überbrückung der Kontakte verursachen könnten. Ein Kurzschluss
zwischen den Akkukontakten kann Verbrennun­gen oder Feuer zur Folge haben.
PBSA 12 D3
DE│AT│CH 
 31
d) Bei falscher Anwendung kann Flüssigkeit aus
dem Akku austreten. Vermeiden Sie den Kon­takt damit. Bei zufälligem Kontakt mit Wasser abspülen. Wenn die Flüssigkeit in die Augen kommt, nehmen Sie zusätzlich ärztliche Hilfe in Anspruch. Austretende Akkuflüssigkeit kann
zu Hautreizungen oder Verbrennungen führen.
e) Benutzen Sie keinen beschädigten oder ver-
änderten Akku. Beschädigte oder veränderte Akkus können sich unvorhersehbar verhalten und zu Feuer, Explosion oder Verletzungsgefahr führen.
f) Setzen Sie einen Akku keinem Feuer oder
zu hohen Temperaturen aus. Feuer oder Tem­peraturen über 130 °C (265°F) können eine Explosion hervorrufen.
g) Befolgen Sie alle Anweisungen zum Laden
und laden Sie den Akku oder das Akkuwerk­zeug niemals außerhalb des in der Betriebs­anleitung angegebenen Temperaturbereichs.
Falsches Laden oder Laden außerhalb des zugelassenen Temperaturbereichs kann den Akku zerstören und die Brandgefahr erhöhen.
VORSICHT! EXPLOSIONSGEFAHR!
Laden Sie nicht aufladbare Batterien niemals auf.
Schützen Sie den Akku vor Hitze,
z. B. auch vor dauernder Sonnenein­strahlung, Feuer, Wasser und Feuchtigkeit. Es besteht Explosionsgefahr.
Sicherheitshinweise für Bohrschrauber
Sicherheitshinweise für alle Arbeiten
WARNUNG!
■ Halten Sie das Elektrowerkzeug an den
isolierten Griffflächen, wenn Sie Arbeiten ausführen, bei denen die Schraube oder das Einsatzwerkzeug verborgene Strom­leitungen treffen kann. Der Kontakt der
Schraube oder des Einsatzwerkzeugs mit einer spannungsführenden Leitung kann auch metallene Geräteteile unter Spannung setzen und zu einem elektrischen Schlag führen.
Sicherheitshinweise bei Verwendung langer Bohrer
■ Arbeiten Sie auf keinen Fall mit einer höheren
Drehzahl als der für den Bohrer maximal zulässigen Drehzahl. Bei höheren Drehzahlen
kann sich der Bohrer leicht verbiegen, wenn er sich ohne Kontakt mit dem Werkstück frei drehen kann, und zu Verletzungen führen.
■ Beginnen Sie den Bohrvorgang immer mit
niedriger Drehzahl und während der Bohrer Kontakt mit dem Werkstück hat. Bei höhe-
ren Drehzahlen kann sich der Bohrer leicht verbiegen, wenn er sich ohne Kontakt mit dem Werkstück frei drehen kann, und zu Verletzun­gen führen.
6. Service
a) Lassen Sie Ihr Elektrowerkzeug nur von quali-
fiziertem Fachpersonal und nur mit Original­Ersatzteilen reparieren. Damit wird sicherge-
stellt, dass die Sicherheit des Elektrowerkzeugs erhalten bleibt.
b) Warten Sie niemals beschädigte Akkus. Sämt-
liche Wartung von Akkus sollte nur durch den Hersteller oder bevollmächtigte Kundendienst­steIlen erfolgen.
32 │ DE
│AT│
CH
■ Üben Sie keinen übermäßigen Druck und
nur in Längsrichtung zum Bohrer aus. Bohrer
können sich verbiegen und dadurch brechen oder zu einem Verlust der Kontrolle und zu Verletzungen führen.
Originalzubehör / -zusatzgeräte
■ Benutzen Sie nur Zubehör und Zusatzgeräte,
die in der Bedienungsanleitung angegeben sind bzw. deren Aufnahme mit dem Gerät kompatibel ist.
PBSA 12 D3
Sicherheitshinweise für Ladegeräte
Dieses Gerät kann von Kindern ab
8 Jahren und darüber sowie von Personen mit verringerten physi­schen, sensorischen oder mentalen Fähigkeiten oder Mangel an Erfah­rung und Wissen benutzt werden, wenn sie beaufsichtigt oder bezüg­lich des sicheren Gebrauchs des Gerätes unterwiesen wurden und die daraus resultierenden Gefah­ren verstehen. Kinder dürfen nicht mit dem Gerät spielen. Reinigung und Benutzer-Wartung dürfen nicht von Kindern ohne Beaufsichtigung durchgeführt werden.
Das Ladegerät ist nur für den
Betrieb im Innenbereich geeignet.
WARNUNG!
Wenn die Netzanschlussleitung dieses
Gerätes beschädigt wird, muss sie durch den Hersteller oder seinen Kundendienst oder eine ähnlich qualifizierte Person ersetzt wer­den, um Gefährdungen zu vermeiden.
ACHTUNG!
Dieses Ladegerät kann nur die folgenden
Batterien laden: PAPK 12 A1 / PAPK 12 A2 / PAPK 12 B1.
Eine aktuelle Liste der Akkukompatibilität
finden Sie unter www.lidl.de/akku.
Vor der Inbetriebnahme
Akku-Pack entnehmen /laden / einsetzen
HINWEIS
Der Akku ist teilgeladen. Laden Sie den Akku
vor Inbetriebnahme idealerweise vollständig auf. Sie können den Li-Ionen-Akku jederzeit aufladen, ohne die Lebensdauer zu verkürzen. Eine Unterbrechung des Ladevorgangs schädigt den Akku nicht.
Laden Sie den Akku-Pack nie, wenn die
Umgebungstemperatur unterhalb 10 °C oder oberhalb 40 °C liegt. Soll ein Lithium-Ionen­Akku längere Zeit gelagert werden, muss regelmäßig der Ladezustand kontrolliert werden. Der optimale Ladezustand liegt zwischen 50 % und 80 %. Das Lagerungskli­ma soll kühl und trocken sein in einer Umgebungstemperatur zwischen 0 °C und 50 °C.
VORSICHT!
Ziehen Sie immer den Netzstecker, bevor
Sie den Akku-Pack nehmen bzw. einsetzen.
1.) Zur Entnahme des Akku-Packs die Entriegelungstasten und ziehen den Akku-Pack aus dem Gerät.
2.) Stecken Sie den Akku-Pack
3.) Stecken Sie den Netzstecker in die Steckdose. Die rote Ladekontroll-LED
4.) Die grüne Ladekontroll-LED dass der Ladevorgang abgeschlossen und der Akku-Pack
5.) Schieben Sie den Akku-Pack
einsatzbereit ist.
Akkuzustand ablesen
Der Zustand bzw. die Restleistung wird bei ein­geschaltetem Gerät in der Akku-LED wie folgt angezeigt:
ROT / ORANGE / GRÜN = maximale Ladung ROT / ORANGE = mittlere Ladung ROT = schwache Ladung – Akku aufladen
aus dem Ladegerät
drücken Sie
in das Ladegerät .
leuchtet rot.
signalisiert Ihnen,
in das Gerät ein.
PBSA 12 D3
DE│AT│CH 
 33
Werkzeuge wechseln
10a
10a
10a
10a
Ihr Akku-Bohrschrauber hat eine vollautomatische Spindelarretierung .
Beim Stillstand des Motors wird der Antriebsstrang verriegelt, so dass Sie das Schnellspannbohrfutter
durch Drehen öffnen können. Nachdem Sie das gewünschte Werkzeug eingesetzt und durch Drehen des Bohrfutters festgespannt haben, können Sie sofort weiter arbeiten. Die Spindelarre­tierung löst sich automatisch mit Starten des Motors (Betätigung des EIN- / AUS-Schalters ).
2-Gang Getriebe
VORSICHT!
Betätigen Sie den Gangwahlschalter
nur bei Stillstand des Gerätes. Ansonsten droht Beschädigung des Gerätes.
Im ersten Gang (Gangwahlschalter
in
Position: 1)
-1
erreichen Sie eine Drehzahl von ca. 350 min
und ein hohes Drehmoment. Diese Einstellung eignet sich für alle Schraubarbeiten.
Im zweiten Gang (Gangwahlschalter
in
Position: 2)
-1
erreichen Sie eine Drehzahl von ca. 1300 min
zur
Durchführung von Bohrarbeiten.
Bohrfutter abnehmen
Um die Bitaufnahme zu benutzen, müssen Sie das Schnellspannbohrfutter
Bohrfutter abnehmen:
Halten Sie das Schnellspannbohrfutter
vorne fest.
Ziehen / schieben Sie den Bohrfutterring
Richtung Schnellspannbohrfutter . Das Schnellspannbohrfutter ist nun entriegelt und kann nach vorne abgezogen werden.
abnehmen.
von
in
Schnellspannbohrfutter aufsetzen:
Um das Schnellspannbohrfutter
wieder aufzusetzen, ziehen Sie den Bohrfutterring Richtung Schnellspannbohrfutter . Schieben Sie dabei das Schnellspannbohrfutter über die Bitaufnahme . Lassen Sie den Bohrfutter­ring
los, um das Schnellspannbohrfutter
einzurasten.
HINWEIS
Sollte das Schnellspannbohrfutter
nicht von selbst einrasten, drehen Sie den Bohrfutterring
.
Bitaufnahme benutzen
Nach Abnahme des Schnellspannbohrfutters können Sie die Bitaufnahme benutzen.
Stecken Sie einen geeigneten Bit in die Bitauf-
nahme
.
Schieben Sie den Bit bis zum Anschlag in die
Bitaufnahme
ein. Durch die Führung und die magnetische Halte­rung sitzt der Bit fest.
Zum Entfernen des Bits ziehen Sie den Bit aus
der Bitaufnahme
heraus.
Drehmomentvorwahl / Bohrstufe
Sie können über die Drehmomentvorwahl die Drehkraft einstellen.
Wählen Sie eine niedrige Stufe für kleine
Schrauben, bzw. weiche Werkstoffe.
Wählen Sie eine hohe Stufe für große Schrau-
ben, harte Werkstoffe, bzw. beim Herausdrehen von Schrauben.
Wählen Sie für Bohrarbeiten die Bohrstufe,
indem Sie die Drehmomentvorwahl Position einstellen.
Schieben Sie für Bohrarbeiten auch den Gang-
wahlschalter
nach vorne (Position: 2).
in die
in
34 │ DE
│AT│
CH
PBSA 12 D3
Inbetriebnahme
Drehrichtung umschalten/ Gerätentriegeln
Entriegeln Sie das Gerät und wechseln Sie die
Drehrichtung, indem Sie den Drehrichtungsum­schalter nach rechts bzw. links durchdrücken.
Ein- / ausschalten
Einschalten:
Drücken Sie zur Inbetriebnahme des Gerätes
den EIN- / AUS-Schalter gedrückt. Die LED-Arbeitsleuchte leicht oder vollständig gedrücktem EIN- / AUS­Schalter des Arbeitsbereiches bei ungünstigen Lichtver­hältnissen.
Ausschalten:
Lassen Sie zum Ausschalten des Gerätes den
EIN- / AUS-Schalter
. Sie ermöglicht so das Ausleuchten
Drehzahl einstellen
Der EIN- / AUS-Schalter verfügt über eine vari­able Geschwindigkeitsregelung. Leichter Druck auf den EIN- / AUS-Schalter Drehzahl. Mit zunehmendem Druck erhöht sich die Drehzahl.
HINWEIS
Die integrierte Motorbremse sorgt für einen
schnellen Stillstand.
Sperre aktivieren
Drücken Sie den Drehrichtungsumschalter in
die Mittelposition. Der EIN- / AUS-Schalter ist blockiert.
Tipps und Tricks
und halten Sie ihn
leuchtet bei
los.
bewirkt eine niedrige
Schraub-Bits sind mit ihren Maßen und der Form
gekennzeichnet. Falls Sie sich unsicher sind probieren Sie immer zuerst aus, ob das Bit ohne Spiel im Schraubenkopf sitzt.
Drehmoment:
Kleinere Schrauben / Bits können beschädigt
werden, wenn Sie ein zu hohes Drehmoment bzw. eine zu hohe Drehzahl einstellen.
Harter Schraubfall (in Metall):
Besonders hohe Drehmomente entstehen z.B.
bei Metallverschraubungen unter Verwendung von Steckschlüsseleinsätzen. Wählen Sie eine niedrige Drehzahl.
Weicher Schraubfall (z.B. in Weichholz):
Schrauben Sie auch hier mit geringer Drehzahl,
um z.B. die Holzoberfläche beim Kontakt mit dem Schraubenkopf aus Metall nicht zu beschä­digen. Verwenden Sie einen Senker.
Beim Bohren in Holz, Metall und anderen Materialien unbedingt berücksichtigen:
Benutzen Sie bei kleinem Bohrer-Durchmesser
eine hohe Drehzahl und bei großem Bohrer­Durchmesser eine niedrige Drehzahl.
Wählen Sie bei harten Materialien eine niedrige
Drehzahl, bei weichem Material eine hohe Drehzahl.
Sichern oder befestigen Sie (wenn möglich) das
Werkstück in einer Spannvorrichtung.
Markieren Sie die Stelle, an der gebohrt werden
soll mit einem Körner oder einem Nagel. Wählen Sie zum Anbohren eine niedrige Drehzahl.
Ziehen Sie den drehenden Bohrer mehrmals
aus dem Bohrloch, um Späne oder Bohrmehl zu entfernen und es zu lüften.
Tipp! So verhalten Sie sich richtig.
Überprüfen Sie vor dem Betrieb, ob der
Schraub bzw. Bohreinsatz korrekt angebracht ist, d.h. zentriert im Bohrfutter sitzt.
PBSA 12 D3
DE│AT│CH 
 35
Bohren in Metall:
Verwenden Sie Metallbohrer (HSS). Für beste
Ergebnisse sollten Sie den Bohrer mit Schneidöl kühlen. Metallbohrer können Sie auch zum Bohren in Kunststoff verwenden. Bohren Sie zunächst mit einem Ø 3 mm Bohrer vor und nähern Sie sich dem gewünschten Bohrdurch­messer.
Bohren in Holz:
Verwenden Sie einen Holzbohrer mit Zentrier-
spitze, für tiefe Bohrungen verwenden Sie einen „Schlangenbohrer”, für große Bohr-Durchmes­ser einen Forstner-Bohrer. Kleine Schrauben in weichem Holz können Sie auch ohne Vorboh­ren direkt eindrehen.
Wartung und Reinigung
WARNUNG! VERLETZUNGSGEFAHR!
Schalten Sie vor allen Arbeiten am Gerät das Gerät aus und entnehmen Sie den Akku.
Der Akku-Bohrschrauber ist wartungsfrei.
Das Gerät muss stets sauber, trocken und frei
von Öl oder Schmierfetten sein.
Es dürfen keine Flüssigkeiten in das Innere der
Geräte gelangen.
Verwenden Sie zum Reinigen des Gehäuses ein
trockenes Tuch. Verwenden Sie niemals Benzin, Lösungsmittel oder Reiniger, die Kunststoff angreifen.
Soll ein Lithium-Ionen-Akku längere Zeit gela-
gert werden, muss regelmäßig der Ladezustand kontrolliert werden. Der optimale Ladezustand liegt zwischen 50 % und 80 %. Das optimale Lagerungsklima ist kühl und trocken.
HINWEIS
Nicht aufgeführte Ersatzteile (wie z. B.
Akku, Schalter) können Sie über unsere Service - Hotline bestellen.
Garantie der Kompernaß Handels GmbH
Sehr geehrte Kundin, sehr geehrter Kunde, Sie erhalten auf dieses Gerät 3 Jahre Garantie ab
Kaufdatum. Im Falle von Mängeln dieses Produkts stehen Ihnen gegen den Verkäufer des Produkts gesetzliche Rechte zu. Diese gesetzlichen Rechte werden durch unsere im Folgenden dargestellte Garantie nicht eingeschränkt.
Garantiebedingungen
Die Garantiefrist beginnt mit dem Kaufdatum. Bitte bewahren Sie den Kassenbon gut auf. Dieser wird als Nachweis für den Kauf benötigt.
Tritt innerhalb von drei Jahren ab dem Kaufdatum dieses Produkts ein Material- oder Fabrikationsfeh­ler auf, wird das Produkt von uns – nach unserer Wahl – für Sie kostenlos repariert, ersetzt, oder der Kaufpreis erstattet. Diese Garantieleistung setzt vo­raus, dass innerhalb der Dreijahresfrist das defekte Gerät und der Kaufbeleg (Kassenbon) vorgelegt und schriftlich kurz beschrieben wird, worin der Mangel besteht und wann er aufgetreten ist.
Wenn der Defekt von unserer Garantie gedeckt ist, erhalten Sie das reparierte oder ein neues Produkt zurück. Mit Reparatur oder Austausch des Produkts beginnt kein neuer Garantiezeitraum.
Garantiezeit und gesetzliche Mängelansprüche
Die Garantiezeit wird durch die Gewährleistung nicht verlängert. Dies gilt auch für ersetzte und reparierte Teile. Eventuell schon beim Kauf vorhan­dene Schäden und Mängel müssen sofort nach dem Auspacken gemeldet werden. Nach Ablauf der Garantiezeit anfallende Reparaturen sind kostenpflichtig.
36 │ DE
│AT│
CH
PBSA 12 D3
Garantieumfang
Das Gerät wurde nach strengen Qualitätsricht­linien sorgfältig produziert und vor Auslieferung gewissen haft geprüft.
Die Garantieleistung gilt für Material- oder Fabrika­tionsfehler. Diese Garantie erstreckt sich nicht auf Produktteile, die normaler Abnutzung ausgesetzt sind und daher als Verschleißteile angesehen wer­den können oder für Beschädigungen an zerbrechli­chen Teilen, z. B. Schalter, Akkus oder Teile, die aus Glas gefertigt sind.
Diese Garantie verfällt, wenn das Produkt beschä­digt, nicht sachgemäß benutzt oder gewartet wur­de. Für eine sachgemäße Benutzung des Produkts sind alle in der Bedienungsanleitung aufgeführten Anweisungen genau einzuhalten. Verwendungs­zwecke und Handlungen, von denen in der Bedie­nungsanleitung abgeraten oder vor denen gewarnt wird, sind unbedingt zu vermeiden.
Das Produkt ist nur für den privaten und nicht für den gewerblichen Gebrauch bestimmt. Bei missbräuchlicher und unsachgemäßer Behandlung, Gewaltanwendung und bei Eingriffen, die nicht von unserer autorisierten Serviceniederlassung vorge­nommen wurden, erlischt die Garantie.
Abwicklung im Garantiefall
Um eine schnelle Bearbeitung Ihres Anliegens zu ge­währleisten, folgen Sie bitte den folgenden Hinweisen:
Bitte halten Sie für alle Anfragen den Kassen-
bon und die Artikelnummer (z.B.IAN123456) als Nachweis für den Kauf bereit.
Die Artikelnummer entnehmen Sie bitte dem Ty-
penschild am Produkt, einer Gravur am Produkt, dem Titelblatt der Bedienungsanleitung (unten links) oder dem Aufkleber auf der Rück- oder Unterseite des Produktes.
Sollten Funktionsfehler oder sonstige Mängel
auftreten, kontaktieren Sie zunächst die nachfol­gend benannte Serviceabteilung telefonisch oder per E-Mail.
Ein als defekt erfasstes Produkt können Sie dann
unter Beifügung des Kaufbelegs (Kassenbon) und der Angabe, worin der Mangel besteht und wann er aufgetreten ist, für Sie portofrei an die Ihnen mitgeteilte Serviceanschrift übersenden.
HINWEIS
Bei Parkside und Florabest Werkzeugen
senden Sie bitte ausschließlich den defekten Artikel ohne Zubehör (z. B. Akku, Aufbewah­rungskoffer, Montagewerkzeuge, etc) ein.
Auf www.lidl-service.com können Sie diese und viele weitere Handbücher, Produktvideos und Installationssoft­ware herunterladen.
Mit diesem QR-Code gelangen Sie direkt auf die Lidl-Service-Seite (www.lidl-service.com) und können mittels der Eingabe der Artikelnummer (IAN) 123456 Ihre Bedienungsanleitung öffnen.
Service
WARNUNG!
► Lassen Sie Ihre Geräte von der Servicestelle
oder einer Elektrofachkraft und nur mit Original-Ersatzteilen reparieren. Damit wird
sichergestellt, dass die Sicherheit des Gerätes erhalten bleibt.
► Lassen Sie den Austausch des Steckers
oder der Netzleitung immer vom Hersteller des Gerätes oder seinem Kundendienst ausführen. Damit wird sichergestellt, dass die
Sicherheit des Gerätes erhalten bleibt.
Service Deutschland
Tel.: 0800 5435 111 (Kostenfrei aus dem dt. Festnetz/Mobilfunknetz) E-Mail: kompernass@lidl.de
Service Österreich
Tel.: 0820 201 222 (0,15 EUR/Min.) E-Mail: kompernass@lidl.at
Service Schweiz
Tel.: 0842 665566 (0,08 CHF/Min., Mobilfunk max. 0,40 CHF/Min.) E-Mail: kompernass@lidl.ch
IAN 322702_1901
PBSA 12 D3
DE│AT│CH 
 37
Importeur
Bitte beachten Sie, dass die folgende Anschrift keine Serviceanschrift ist. Kontaktieren Sie zunächst die benannte Servicestelle.
KOMPERNASS HANDELS GMBH BURGSTRASSE 21 44867 BOCHUM GERMANY www.kompernass.com
Entsorgen Sie die Verpackung umwelt­gerecht. Beachten Sie die Kennzeichnung auf den verschiedenen Verpackungs­materialien und trennen Sie diese gegebenenfalls gesondert. Die Ver­packungs materialien sind gekenn­zeichnet mit Abkürzungen (a) und Ziffern (b) mit folgender Bedeutung: 1–7: Kunststoffe, 20–22: Papier und Pappe, 80–98: Verbundstoffe
Entsorgung
Die Verpackung besteht aus umweltfreund-
lichen Materialien, die Sie über die örtlichen Recyclingstellen entsorgen können.
Werfen Sie Elektrowerkzeuge nicht
in den Hausmüll!
Gemäß Europäischer Richtlinie 2012/19/EU müssen verbrauchte Elektrowerkzeuge getrennt gesammelt und einer umweltgerechten Wiederver­wertung zugeführt werden.
Werfen Sie Akkus nicht in den
Hausmüll!
Entfernen Sie die Akkus vor der Entsorgung aus dem Gerät. Defekte oder verbrauchte Akkus müssen gemäß Richtlinie 2006/66/EG recycelt werden. Geben Sie Akku-Pack und / oder das Gerät über die an­gebotenen Sammeleinrichtungen zurück. Über Entsorgungsmöglichkeiten für ausgediente Elektrowerkzeuge / Akku-Pack informieren Sie sich bitte bei Ihrer Gemeinde- oder Stadtverwaltung.
Möglichkeiten zur Entsorgung des ausgedienten Produkts erfahren Sie bei Ihrer Gemeinde- oder Stadtver­waltung.
38 │ DE
│AT│
CH
PBSA 12 D3
Original-Konformitätserklärung
Wir, KOMPERNASS HANDELS GMBH, Dokumentenverantwortlicher: Herr Semi Uguzlu, BURGSTR. 21, DE - 44867 BOCHUM, DEUTSCHLAND, erklären hiermit, dass dieses Produkt mit den folgenden Normen, normativen Dokumenten und EG-Richtlinien übereinstimmt:
Maschinenrichtlinie (2006 / 42 / EG)
EG-Niederspannungsrichtlinie (2014 / 35 / EU) (Nur Ladegerät)
Elektromagnetische Verträglichkeit (2014 / 30 / EU)
RoHS Richtlinie (2011 / 65 / EU)*
*Die alleinige Verantwortung für die Ausstellung dieser Konformitätserklärung trägt der Hersteller. Der oben beschriebene Gegenstand der Erklärung erfüllt die Vorschriften der Richtlinie 2011/65/EU des Europäischen Parlaments und des Rates vom 8. Juni 2011 zur Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten.
Angewandte harmonisierte Normen:
EN 62841-1:2015 EN 62841-2-1:2018 EN 60335-1:2012/A13:2017 EN 60335-2-29:2004/A11:2018 EN 62233:2008 EN 55014-1:2017 EN 55014-2:2015 EN 61000-3-2:2014 EN 61000-3-3:2013 EN 50581:2012
Typ / Gerätebezeichnung: Akku-Bohrschrauber PBSA 12 D3 Herstellungsjahr: 05 - 2019 Seriennummer: IAN 322702_1901
Bochum, 11.06.2019
Semi Uguzlu
- Qualitätsmanager ­Technische Änderungen im Sinne der Weiterentwicklung sind vorbehalten.
PBSA 12 D3
DE│AT│CH 
 39
Ersatz Akku Bestellung
Wenn Sie einen Ersatz-Akku für Ihr Gerät bestellen möchten, so können Sie dies entweder bequem im Internet unter www.kompernass.com oder telefonisch abwickeln. Dieser Artikel kann aufgrund begrenzter Vorratsmenge nach kurzer Zeit ausverkauft sein.
HINWEIS
Die Bestellung von Ersatzteilen kann in einigen Ländern nicht online vorgenommen werden.
Kontaktieren Sie in diesem Fall bitte die Service-Hotline.
Die Aktion ist begrenzt auf einen Akku pro Kunde / Gerät, sowie auf eine Laufzeit von zwei Monaten
nach dem Aktionszeitraum. Danach kann der Ersatzakku als Ersatzteil zu anderen Konditionen weiter­hin bestellt werden.
Telefonische Bestellung
Service Deutschland
Tel.: 0800 5435 111 (kostenfrei aus dem dt. Festnetz/Mobilfunknetz)
Service Österreich
Tel.: 0820 201 222 (0,15 EUR/Min.) E-Mail: kompernass@lidl.at
Service Schweiz
Tel.: 0842 665566 (0,08 CHF/Min., Mobilfunk max. 0,40 CHF/Min.) E-Mail: kompernass@lidl.ch
Um eine schnelle Bearbeitung Ihrer Bestellung zu gewährleisten, halten Sie bitte für alle Anfragen die Artikelnummer (z. B. IAN 322702) des Gerätes bereit. Die Artikelnummer entnehmen Sie bitte dem Typenschild oder dem Titelblatt dieser Anleitung.
40 │ DE
│AT│
CH
PBSA 12 D3
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21 44867 BOCHUM GERMANY www.kompernass.com
Versione delle informazioni · Last Information Update · Stand der Informationen: 07 / 2019 · Ident.-No.: PBSA12D3-062019-1
IAN 322702_1901
Loading...