Owner's Manual
Laser Display Screen
Please read the safety information carefully before using the product.
SC105
P/NO : MFL67864905 (1307-REV01) |
www.lg.com |
2 Safety Precautions
Please take note of the safety instructions to prevent any potential accident or misuse of the product.
yySafety precautions are given in two forms, i.e. Warning and Caution as detailed below.
WARNING: Failure to follow the instructions may cause serious injury and even death.
CAUTION: Failure to follow the instructions may cause minor injury or damage to the product.
yyRead the owner's manual carefully and keep it at hand.
Installation
WARNING |
CAUTION |
yyThe product should be installed by a qualified professional specified by the retail store.
- The product installation by a nonqualified personnel is dangerous and may cause personal injury.
yyThe product should be installed where its weight can be supported.
- Otherwise, the product may fall and cause personal injury.
yyWhen moving or replacing the product after installation, contact a qualified installer specified by the retail store.
- If an unqualified person moves and installs the product, this may cause safety issues as this task requires the special technique.
yyDo not hang on the product or apply shock to the product.
- The product may fall and cause injury.
yyFollow the instructions in the manual to install the product.
- Otherwise, it may cause serious injury or damage to the product.
yyWhen installing the product or adjusting the height of the product, two or more people are needed.
- If you do it by yourself, you may drop the product causing personal injury or damage to the product.
yyWhen installing the product, check whether the wall is strong enough to hold the product and use the anchors and screws provided.
- Otherwise, the product could fall causing safety issues.
Safety Precautions |
3 |
CAUTION
yyWhen drilling the holes in the wall, make sure you use a drill and a drill bit with the specified size of diameter. Ensure that you also follow the instructions regarding the depth of the holes.
- Otherwise, the product may be installed improperly causing safety issues.
yyDo not clean the product with wet towels, and do not use a heater or humidifier underneath the product. - Moisture permeating into the product, steam or heat may result in fire, electric shock or damage to the product.
yyKeep the product away from sprinklers, sensors, high-tension wires and power sources. Do not install the product in a location where vibrations or shock impacts are likely to occur.
yyWear working gloves when installing the product. Do not use bare hands. - Otherwise, it may cause personal injury.
yyDo not place the product where it is directly exposed to the light.
- The image may look dark due to the light.
4 PREPARATION
PREPARATION
Accessories
Check the accessories provided with the product. The picture may be different from the actual product.
Accessories are subject to change without prior notice in order to improve the performance of the product. New accessories may be added or old ones may be removed.
|
|
Up |
|
|
|
Down |
|
8 anchors for |
|
|
|
attaching rings |
8 bolts for attaching |
Magnet 15 EA Paper template |
|
(Ф8) |
rings (Ф8) |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 sheet of warp |
|
|
1 piece of tape to |
||||||||||||
|
|
|
|
|
||||||||||||||
Tape 6 EA |
2 Rings |
attach the paper |
||||||||||||||||
correction sponge |
||||||||||||||||||
|
|
|
|
|
|
template |
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
18 Steel Spacers |
1 warp correction ring |
Safety lock pin |
Thread |
|
2 EA |
||||
|
|
|
Preparations
Drill (M6, M8), leveler, tapeline, driver, tape