795.7259#
MFL68680470
Rev.00_082917
TABLE OF CONTENTS
Warranty.................................................................. |
3 |
Product Record....................................................... |
4 |
Important Safety Instructions ........................ |
5-7 |
Electrical & Grounding Requirements ..... |
....... 7 |
Parts and Features .............................................. |
8 |
Refrigerator Installation .............................. |
9-20 |
Unpacking Your Refrigerator .......................... |
9 |
Installation ....................................................... |
10 |
Removing/Replacing Your Refrigerator and |
|
Freezer Handles, Doors and Drawers ..... |
11-19 |
Leveling and Door Alignment ...................... |
20 |
Using Your Refrigerator ............................ |
21-34 |
Setting the Controls .................................. |
21-22 |
Smart Features ............................................... |
23 |
Instruction for Smart Grid ...................... |
24-25 |
In-Door Ice Bin ................................................... |
26 |
Automatic Icemaker ............................... |
27-28 |
Food Storage Guide ........................................ |
29 |
Refrigerator Section |
|
Water Dispenser ........................................... |
30 |
Refrigerator Shelves ........................................ |
31 |
Humidity Controlled Crisper ........................ |
32 |
Temperature Controlled Pantry Drawer....... |
32 |
Door Bin ............................................................ |
32 |
Air Filter .......................................................... |
33 |
Freezer Section |
|
Extra Ice Bin ............................................. |
.......33 |
Durabase ........................................................ |
33 |
Durabase Divider....................................... |
......33 |
Water Filter ................................................ |
34-36 |
Care And Cleaning..................................... |
37-89 |
General Cleaning Tips ............................. |
......37 |
Exterior .......................................................... |
37 |
Inside Walls ................................................... |
37 |
Door Liner and Gaskets ........................... |
......37 |
Plastic Parts .................................................... |
37 |
Condenser Coils ........................................ |
......37 |
Light Bulb Replacement ........................... |
......38 |
Power Interruptions ...................................... |
38 |
When You Go On Vacation .................... |
......38 |
When You Move .......................................... |
38 |
Connecting the Water Line........................39-41
Troubleshooting Guide..............................42-49
Diagnostics ........................................................ |
50 |
2
WARRANTY
REFRIGERATOR WARRANTY
KENMORE LIMITED WARRANTY
FOR ONE YEAR from the date of sale this appliance is warranted against defects in material or workmanship when it is correctly installed, operated and maintained according to all supplied instructions. WITH PROOF OF SALE, a defective appliance will receive free repair or replacement at option of seller. For warranty coverage details to obtain free repair or replacement, visit the web page: www.kenmore.com/warranty
This warranty applies for only 90 DAYS from the sale date in the United States, and is void in Canada, if this appliance is ever used for other than private household purposes.
This warranty covers ONLY defects in material and workmanship, and will NOT pay for:
1.Expendable items that can wear out from normal use, including but not limited to filters, belts, bags or screw-in base light bulbs.
2.A service technician to clean or maintain this appliance, or to instruct the user in correct appliance installation, operation and maintenance.
3.Service calls to correct appliance installation not performed by Sears authorized service agents, or to repair problems with house fuses, circuit breakers, house wiring, and plumbing or gas supply systems resulting from such installation.
4.Damage to or failure of this appliance resulting from installation not performed by Sears authorized service agents, including installation that was not in accord with electrical, gas or plumbing codes.
5.Damage to or failure of this appliance, including discoloration or surface rust, if it is not correctly operated and maintained according to all supplied instructions.
6.Damage to or failure of this appliance, including discoloration or surface rust, resulting from accident, alteration, abuse, misuse or use for other than its intended purpose.
7.Damage to or failure of this appliance, including discoloration or surface rust, caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.
8.Damage to or failure of parts or systems resulting from unauthorized modifications made to this appliance. 9.Service to an appliance if the model and serial plate is missing, altered, or cannot easily be determined to
have the appropriate certification logo.
Disclaimer of implied warranties; limitation of remedies
Customer’s sole and exclusive remedy under this limited warranty shall be product repair or replacement as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
Seller shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation on the duration of implied
warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.
This warranty applies only while this appliance is used in the United States or Canada*.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
*In-home repair service is not available in all Canadian geographical areas, nor will this warranty cover user or servicer travel and transportation expenses if this product is located in a remote area
(as defined by Sears Canada Inc.) where an authorized servicer is not available.
Sears Brands Management Corporation, Hoffman Estates, IL 60179
Sears Canada Inc., Toronto, Ontario, Canada M5B 2C3
3
PRODUCT RECORD
In the space below, record the date of purchase, model and serial number of your product. You will find the model and serial number printed on an identification label located on the interior liner of the refrigerator compartment. Have these items of information available whenever you contact Sears concerning your product.
Model No.___________________ |
Date of Purchase ___________________ |
Serial No.___________________ |
|
Save these instructions and attach your sales receipt for future reference.
4
IMPORTANT SAFETY INSTRUCTIONS
BASIC SAFETY PRECAUTIONS
This guide contains many important safety messages. Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard signal word DANGER, WARNING or CAUTION. These words mean:
DANGER
WARNING
CAUTION
You will be killed or seriously injured if you do not follow instructions.
You can be killed or seriously injured if you do not follow instructions.
Indicates an imminently hazardous situation which, if not avoided, may result in minor or moderate injury, or product damage.
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
WARNING
To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety precautions should be followed, including the following.
Read all instructions before using this appliance.
•NEVER unplug your refrigerator by pulling on the power cord. Always grip the plug firmly and pull it straight out from the outlet.
•If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.
•Do not modify or extend the power cord length. It could cause electric shock or fire.
•When moving your refrigerator away from the wall, be careful not to roll over or damage the power cord.
•DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
•DO NOT allow children to climb, stand, or hang on the refrigerator doors or shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.
•Keep fingers out of pinch point areas; clearances between the doors and cabinets are necessarily small. Be careful closing doors when children are in the area.
•Unplug your refrigerator before cleaning or making any repairs.
NOTE: It is strongly recommended that any service be performed by a qualified technician.
SAVE THESE INSTRUCTIONS
5
WARNING
•Before replacing a burned-out or broken light bulb, unplug the refrigerator or turn off power at the circuit breaker or fuse box in order to avoid contact with a live wire filament. (A burned-out light bulb may break when being replaced exposing the wire filament.)
NOTE: Some models have LED interior lighting and service should be performed by a qualified technician.
WARNING: Setting either or both controls to the OFF position does not remove power to the light circuit.
•When you are finished, reconnect the refrigerator to the electrical source and reset the controls (Thermostat, Refrigerator Control, and or Freezer Control, depending on the model) to the desired setting.
•This refrigerator must be properly installed in accordance with the Attention Installer Instructions that were taped to the front of the refrigerator.
•After your refrigerator is in operation, do not touch the cold surfaces in the freezer compartment when hands are damp or wet. Skin may adhere to the extremely cold surfaces.
•DO NOT touch the automatic ice making mechanism while the refrigerator is plugged in.
•DO NOT refreeze frozen foods which have thawed completely. The United States Department of Agriculture in Home and Garden Bulletin No. 69 says:
…You may safely refreeze frozen foods that have thawed if they still contain ice crystals or if they are still cold—below 39°F (4°C).
…Thawed ground meats, poultry or fish that have any off-odor or off-color should not be refrozen and should not be eaten. Thawed ice cream should be discarded.
If the odor or color of any food is poor or questionable, dispose of it. The food may be dangerous to eat.
Even partial thawing and refreezing reduces the eating quality of foods, particularly fruits, vegetables and prepared foods. The eating quality of red meats is affected less than that of many other foods. Use refrozen foods as soon as possible to save as much of their quality as you can.
WARNING : This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. (USA only)
SAVE THESE INSTRUCTIONS
DANGER: RISK OF CHILD ENTRAPMENT
Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. If you are getting rid of your old refrigerator, please follow the instructions at right to help prevent accidents (child entrapment and suffocation).
BEFORE YOU THROW AWAY
YOUR OLD REFRIGERATOR
OR FREEZER:
•Take off the doors.
•Leave the shelves in place so that children may not easily climb inside.
6
CFC/HCFC DISPOSAL
Your old refrigerator may have a cooling system that used CFCs or HCFCs (chlorofluorocarbons or hydrochlorofluorocarbons). CFCs and HCFCs are
believed to harm stratospheric ozone if released to the atmosphere. Other refrigerants may also cause harm to the environment if released to the atmosphere.
If you are throwing away your old refrigerator, make sure the refrigerant is removed for proper disposal by a qualified technician. If you intentionally release
refrigerant, you may be subject to fines and imprisonment under provisions of environmental legislation.
ELECTRICAL & GROUNDING REQUIREMENTS
IMPORTANT: Please read carefully.
TO CONNECT ELECTRICITY
WARNING
Electrical Shock Hazard
FOR PERSONAL SAFETY, this appliance must be properly grounded. Have the wall outlet and the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
3-prong grounding type
wall receptacle
3-prong grounding plug 
Ensure proper ground exists before use.
RECOMMENDED GROUNDING METHOD
The refrigerator should always be plugged into its own individual properly grounded electrical outlet rated for 115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. It is recommended that a separate circuit serving only this appliance be provided.
Use a receptacle that cannot be turned off with a switch or pull chain. Do not use an extension cord.
Where a standard two-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded three-prong wall outlet.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, the use of an extension cord is not recommended. However, if you still elect to use an extension cord, it is absolutely necessary that it be a UL-listed (USA), 3-wire grounding type appliance extension cord having a grounding type plug and outlet, and that the electrical rating of the cord be 15 amperes
(minimum) and 120 volts.
Use of an extension cord will increase the clearance needed for the back of the refrigerator.
7
PARTS AND FEATURES
A K B 
M
O 
P
L
D
F 
Q
C 
H G
C
H
I E J
N
Use this page to become more familiar with the parts and features of your refrigerator.
NOTE: This guide covers several different models. The refrigerator you have purchased may have some or all of the items listed below. The locations of the features shown below may not match your model.
A Refrigerator Light B Water Filter
C Fixed Door Bins
D IceComp artme nt (Icemaker and Ice Bin)
E Extra Ice Bin
F Articulat ing Mull ion G Water Tank Cover H Crisper
I Pantry Drawer
J Durabase Divider
K |
Diagnostic s Speaker |
Icemaker |
Ice Bin |
L |
Refrigerator Shelves |
|
|
|
Ice Compartment |
||
M Air Filter |
|
||
|
Door |
||
N Durabase |
|
|
|
O Door Bins |
|
|
|
P |
Dairy Bin |
|
|
Q Modular Door Bin
8
REFRIGERATOR INSTALLATION
WARNING
Excessive Weight Hazard:
Use two or more people to move and install the refrigerator. Failure to do so can result in back or other injury.
UNPACKING YOUR REFRIGERATOR
Remove tape and any temporary labels from your refrigerator before using. Do not remove any warningtype labels, the model and serial number label, or the Tech Sheet that is located under the front of the refrigerator.
To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator.
Refrigerator shelves are installed in the shipping position. Please reinstall shelves according to your individual storage needs.
WARNING
Excessive Weight Hazard:
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator when trying to move it, as floor damage could occur.
WARNING
Explosion Hazard:
Keep flammable materials and vapors, such as gasoline, away from the refrigerator. Failure to do so can result in fire, explosion, or death.
9
REFRIGERATOR INSTALLATION
PRIOR TO USE |
INSTALLATION (continued) |
1.Clean your refrigerator thoroughly and wipe off all dust that accumulated during shipping.
2.Install accessories such as ice cube bin, drawers, shelves, etc., in their proper places. They are packed together to prevent possible damage during shipment.
3.Allow your refrigerator to run for at least two to three hours before putting food in it. Check the flow of cold air in the freezer compartment to ensure proper cooling. Your refrigerator is now ready for use.
INSTALLATION
The refrigerator should always be plugged into its own individual properly grounded electrical outlet rated for 115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. It is recommended that a separate circuit serving only this appliance be provided.
This appliance is intended to be used in household and similar applications such as staff kitchen areas in shops, offices and other working environments; farm houses and by clients in hotels, motels and other residential type environments; bed and breakfast type
environments; catering and similar non-retail applications.
WARNING
Shock Hazard:
To reduce the risk of electric shock, do not install the refrigerator in a wet or damp area.
1.To avoid noise and vibration, the unit must be leveled and installed on a solidly constructed floor. If required, adjust the leveling legs to compensate for unevenness of the floor. The front should be slightly higher than the rear to aid in door closing. Leveling legs can be turned easily by tipping the cabinet slightly. Turn the leveling legs to the left to raise the unit or to the right to lower it. (See Leveling and door AlIgnment.)
NOTE: Installing on carpeting, soft tile surfaces, a platform or weakly supported structure is not recommended.
2.Install this appliance in an area where the temperature is between 55°F (13°C) and 110°F (43°C). If the temperature around the appliance is too low or high, cooling ability may be adversely affected.
3.Select a place where a water supply can be easily connected for the automatic icemaker.
NOTE: The water pressure must be from 20-120 psi or 138-827 kPa or 1.4-8.4 kgf/cm². If the refrigerator is installed in an area with low water pressure (below 20 psi), you can install a booster pump to compensate for the low pressure.
4.Too small of a distance from adjacent items may result in lowered freezing capability and increased electricity consumption charges. Allow at least 24 inches (61 cm) in front of the refrigerator to open the doors and at least 2 inches (5.08 cm) between the back of the refrigerator and the wall.
2" (5.08 cm) |
10
REFRIGERATOR INSTALLATION
NOTE: Removing the doors is always recommended when it is necessary to move the refrigerator through a narrow opening. If it is necessary to remove the handles, follow the directions below.
HOW TO REMOVE REFRIGERATOR
DOOR HANDLE Mounting
Fasteners
NOTE: Handle appearance may vary from the illustrations on this page.
Set Screw
Removing Refrigerator Handle
Loosen the set screws with a 3/32 in. Allen wrench and remove the handle.
NOTE: If the handle mounting fasteners need to be tightened or removed, use a ¼ in. Allen wrench.
Allen
Wrench
HOW TO REPLACE REFRIGERATOR DOOR HANDLE
NOTE: Handle appearance may vary from the illustrations on this page.
Replacing Refrigerator Door Handle
Place the handle on the door by fitting the handle footprints over the mounting fasteners and tightening the set screws with a 3/32 in Allen wrench.
NOTE: If the handle mounting fasteners need to be tightened or removed, use a ¼ in. Allen wrench.
Mounting
Fasteners
11
REFRIGERATOR INSTALLATION
NOTE: Removing the doors is always recommended when it is necessary to move the refrigerator through a narrow opening. If it is necessary to remove the handles, follow the directions below.
HOW TO REMOVE FREEZER DOOR HANDLE
NOTE: Handle appearance may vary from the illustrations on this page.
Removing Freezer Drawer Handle
Loosen the set screws located on the lower side of the handle with a ⅛/8 in. Allen wrench and remove the handle.
NOTE: If the handle mounting fasteners need to be tightened or removed, use a ¼ in. Allen wrench.
HOW TO REPLACE FREEZER DOOR HANDLE
NOTE: Handle appearance may vary from the illustrations on this page.
Replacing Freezer Drawer Handle
Place the handle on the door by fitting the handle footprints over the mounting fasteners and tightening the set screws with a 1/8 in. Allen wrench.
NOTE: If the handle mounting fasteners need to be tightened or removed, use a ¼ in. Allen wrench.
WARNING
When assembling or disassembling the handles:
• Grasp the handle firmly to ensure it will not drop or cause injury.
•Prevent the handle from swinging toward nearby people or animals.
•Insert the bracket hole of the handle into the stopper bolt of the door exactly, then assemble the set screws to fix the handle in place.
•Check for any gap between the door and handle after the handle is fixed in place.
12
REMOVING AND REPLACING
REFRIGERATOR DOORS
WARNING
Excessive Weight Hazard:
Use two or more people to remove and install the refrigerator doors. Failure to do so can result in back or other injury.
WARNING
Electrical Shock Hazard
•Disconnect the electrical supply to the refrigerator before installing. Failure to do so could result in serious injury or death.
•Do not put hands, feet or other objects into the air vents or bottom of the refrigerator. You may be injured or receive an electrical shock.
To remove the left refrigerator door:
1The water supply is connected to the upper
right part of the rear surface of the refrigerator. Remove the ring in the joint area. Hold the water supply connection and gently push the collet (1)to detach the water supply line (2) as shown.
2Remove the screw (1) from the hinge cover at the top of the refrigerator. Lift the hook (not visible), located at the bottom of the front side of the cover
(2) with a flat-heat screwdriver.
REFRIGERATOR INSTALLATION
3Remove the cover and pull out the tube (1). Disconnect all wire harnesses (2). Unscrew the ground wire (3).
4Rotate the hinge lever counterclockwise (1). Lift the top hinge (2) free of the hinge lever latch.
Hinge Lever Latch
(1)
(2)
CAUTION
When lifting the hinge free of the latch, be careful that the door does not fall forward.
5Lift the door from the middle hinge pin and remove the door.
CAUTION
Place the door, inside facing up, on a nonscratching surface.
13
REFRIGERATOR INSTALLATION
NOTE
Disassembling/Assembling the Water Lines
Collet |
|
Tube |
|
Insert line |
|
Clip |
(Correct) |
|
Removing the Right Refrigerator Door
1Remove the top hinge cover screw (1). Lift
the hook (not visible), located at the bottom of the front side of the cover (2), with a flat-head screwdriver.
2 Detach the wire harness (1).
3Rotate the hinge lever (1) clockwise. Lift the top hinge (2) free of the hinge lever latch.
Hinge Lever Latch
CAUTION
When lifting the hinge free of the latch, be careful that the door does not fall forward.
4Lift the door from the middle hinge pin and remove the door.
CAUTION
Place the door, inside facing up, on a nonscratching surface.
Assembling the Right Refrigerator Door
Install the right-side door first.
1Make sure that the plastic sleeve is inserted in the bottom of the door. Lower the door onto the middle hinge pin as shown in the figure.
2Fit the hinge (1) over the hinge lever latch and slot it into place. Rotate the lever (2) counterclockwise to secure the hinge.
Hinge Lever Latch
3 Connect the wire harness (1).
14
4Place the cover (1) in its place. Insert and tighten the cover screw (2).
Assembling the Left Refrigerator Door
Install the left refrigerator door after the right door is installed.
1Make sure that the plastic sleeve is inserted in
the bottom of the door. Install the refrigerator door onto the middle hinge.
2Fit the hinge (1) over the hinge lever latch and slot it into place. Rotate the lever clockwise (2) and fasten the hinge.
Hinge Lever Latch
3 Connect all the wire harnesses.
REFRIGERATOR INSTALLATION
4Push the water supply tube into the hole on the top case and pull it through the backplate.
5Hold the water supply connection and gently push in the collet (1) to connect the water supply line
(2) as shown. Insert the tube at least 5/8 inch (15 mm) into the connector. Insert the clip on the joint to fasten the tube in place.
Collet
6Place the cover (1) in place. Insert and tighten the cover screw (2).
NOTE
Disassembling/Assembling the Water Lines
Collet
Tube
Insert line |
|
Clip |
(Correct) |
|
Gently press the collet and insert the tube until only one line shows on the tube.
(Correct) |
(Incorrect) |
15
Loading...