VM9224BT
EJECT
Installation Guide
MUTE
A/V INPUT
VM9224BT
What’s in the Box
VM9224BT Head Unit
Left and Right Double DIN
Mounting Brackets
Double DIN Half Sleeve Install Bracket
External Microphone
Two Custom Cosmetic Trim Rings
Parking Brake Wire
Hardware Bag
Speaker Output Harness
Power Input Harness
2 x Accessory Harness
Installation Guide
Tools and Supplies
You will need these tools and supplies to
install your VM9224BT:
• Torx type, fl at-head and Philips
screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screw
driver, socket wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Never install this unit where operation and viewing could interfere with
safe driving conditions.
1
Optional Equipment
• NAV102: Allows you to access navigation features. All installation and operating instructions are included
with the navigation module.
• Rear Camera
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the VM9224BT is to be installed in a car equipped with an on-board drive or navigation computer, do
not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these
conditions, use extra caution during installation to avoid causing a short circuit.
Replacing the Fuse
When replacing the fuse, use a new 20A replacement fuse. Using a fuse with an improper rating could damage
the unit and cause a fi re.
ISO-DIN Installation
This unit is designed to fi t into a 2.0 DIN dashboard opening, found in many imported cars. The unit has
threaded holes in the chassis side panels which may be used with the original factory mounting brackets of
some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard.
Please consult with your local car stereo specialty shop for assistance on this type of installation.
Remove the existing factory radio from the dashboard or
1
center console mounting. Save all hardware and brackets
as they will be used to mount the new radio.
Remove the factory mounting brackets and hardware from
2
the existing radio and attach them to the new radio.
EJECT
CAUTION: Do not exceed M5 X 6MM screw size. Longer
screws may damage components inside the chassis.
Place the radio in front of the dashboard opening so the
3
MUTE
wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape. After completing the wiring connections, plug the
ISO connectors into the mating sockets on the rear of the
chassis. Turn the unit on to confi rm operation (vehicle ignition switch must be “on”). If the unit does not
operate, re-check all wiring until the problem is corrected.
Mount the new radio assembly to the dashboard or center console using the reverse procedure in step 1.
4
CAUTION! Be careful not to damage the car wiring.
NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local,
state and federal laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.
CAUTION: Do not block the cooling fan exit. If blocked, the unit may overheat and become damaged.
2
Installation Using Half-Sleeve
Install half-sleeve in the dashboard.
1
a. Install adapter if necessary (optional).
b. Install half-sleeve into adapter or dashboard (use only
the supplied screws). Do not force the sleeve into the
opening or cause it to bend or bow.
WARNING! Only connect the unit to a 12-volt power
supply with proper grounding.
c. Locate the series of bend-tabs along the top, bottom
and sides of the mounting sleeve. With the sleeve fully
inserted into the dashboard opening, bend as many of
the tabs outward as necessary so that the sleeve is
fi rmly secured to the dashboard.
Use the M5 x 6 screws (provided) to install the mounting
2
brackets to each side of the radio using the holes indicated
in the diagram. DO NOT USE OTHER SCREWS.
Place the radio in front of the dashboard opening so the
3
wiring can be brought through the mounting sleeve.
Complete wiring as illustrated in the wiring diagram. Once
4
the wiring is complete, reconnect the battery negative
terminal. If there is no ACC available, connect the ACC lead
to the power supply with a switch.
CAUTION! Be careful not to damage the car wiring.
After completing the wiring connections, turn the unit on
5
to confi rm operation (ignition switch must be on). If unit does
not operate, recheck all wiring until problem is corrected.
Once proper operation is achieved, turn off the ignition
switch and proceed with fi nal mounting of the chassis.
a. Connect wiring adapter to existing wiring harness.
b. Connect antenna lead.
c. Carefully slide the radio into the half-sleeve, making
sure it is right-side-up. Use the supplied screws to attach the radio to the half sleeve.
Step 1-b
Step 1-c
TAB
DASHBOARD
Step 2
Step 5-c
Using the Cosmetic Trim Ring
Two cosmetic trim rings are packaged with the head unit for
installation fl exibility. This unit will fi t into most import dashes
with little or no modifi cation to the dash board/cavity. Some US
domestic vehicle dashes will accept a Double-DIN chassis, but
there is usually a small gap between the radio and dash piece after installation is complete. In this case, use the appropriate trim
ring to conceal any gaps that may be present.
NOTE: For proper operation of the CD/DVD player, the chassis
must be mounted within 30° of horizontal. Make sure the unit
is mounted within this limitation.
3
TRIM RING
MOUNTING
SLEEVE
Wiring Diagram
GPS
DVB-T
GREEN(+)
GREEN/BLACK(-)
WHITE(+)
WHITE/BLACK(-)
GREY(+)
GREY/BLACK(-)
PURPLE(+)
PURPLE/BLACK(-)
BATTERY
+
-
IGNITION SWITCH
RED
YELLOW
BLACK
BROWN
(-)
Cell Phone
GND
MUTE
BATT
ACC
REAR R
FRONT L
REAR L
FRONT R
BLUE
GREEN
YELLOW
PINK (-)
BRAKE
BLUE/WHITE
BLUE
P.CONT
ANT.CONT
BLUE
RED
WHITE
RED
WHITE
FRONT L
FRONT R
REAR L
REAR R
SUBWOOFER
GREEN/WHITE (+)
REVERSE
IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully, or
have the installation handled by an experienced technician.
Need Help? For technical assistance, call the Jensen customer support line at 1-800-323-4815.
SUBWOOFER
VIDEO OUT
BLUE
YELLOW
External PowerAmplifier
Rear Video
iPod
MICROPHONE
Steering WheelControl
(SWC) requires
SWI-PS InterfaceAdapter,
Sold Separately
PAC
3.5mm Stereo Socket
RADIO ANT
External
Microphone
Antenna Jack
NAV BUS
SWC
Cell Phone
Antenna
Auto antenna
control (connect
to antenna control
lead and power
supply of antenna
amplifier)
(-)
BROWN
(20A)
FILTER/FUSE
GREEN/WHITE (+)
FRONT R
Rear View
Video Camera
YELLOW
ANT.CONT
CAMERA-VIDEO
4
Loading...