Integra DTR-50.1 Owner's Manual
Speaker Hookup
QUICK SETUP
Model : DTR-50.1
Thank you for purchasing this product.
This quick setup sheet shows the typical hookup method
for connecting speakers and AV components (DVD/BD player,
TV, cable/satellite receiver).
For more detailed hookup information and operating
instructions, please see the Instruction Manual.
Speaker Layout (Main Room)
Front
high right
speaker
Front
wide right
speaker
Front
right
speaker
Center
speaker
Front
left
speaker
Front
wide left
speaker
Front
high left
speaker
Sub
woofer
Sub
woofer
Front
Wide Left
Surround
Surround
Left
Left
Front
Left
Front
High
Left
TV
TV
Center
Listener
Listener
Front
Right
Front
High
Right
Front
Wide Right
Surround
Surround
Right
Right
*1
1/2''-5/8''
(12-15mm)
Surround
Surround
Back
Back
Left
Left
Surround
Surround
Back
Back
Right
Right
Powered
subwoofer
*1 The same signal is output from each jack.
Surround
right speaker
Surround back
right speaker
Surround back
left speaker
Surround
left speaker
See the other side of this sheet for the AV component hookup.
SN 29400040(C) Copyright 2009 ONKYO CORPORATION Japan. All rights reserved.
* 2 9 4 0 0 0 4 0 *
AV Component Hookup
With an HDMI cable you can send both audio and video with a single cable,
making connecting simple and keeping wires neat.
If you have an HDMI-compatible TV and players, you can connect them
to the AV receiver with HDMI cables. Digital audio signals received
at HDMI IN input are output to the speakers and headphones connected
to the AV receiver.
See the other side of this sheet for the speaker hookup.
If your TV or player doesn’t support HDMI, use the analog or digital
connections shown below.
IF NO HDMI
HDMI
OUT
HDMI
IN
DVD/BD player
TV
DIGITAL
OUT
COAXIAL
AUDIO
OUT
L
R
VIDEO
OUT
DVD player
TV
VIDEO 1
IN
Please ensure the monitor input
(VIDEO 1, VIDEO 2, VIDEO 3, etc.)
selected corresponds to actual
connection used.
HDMI
OUT
Cable/satellite
Using the HDMI Inputs
If there’s no picture on your TV, you’ll need to
assign the HDMI inputs as necessary using the
onscreen setup menus.
If you connect your DVD/BD player to the AV
receiver’s HDMI IN 1, and connect your cable
or satellite receiver to HDMI IN 3, as shown,
it’s not necessary to change the default
assignments.
Antenna input
(e.g., RF IN)
On the front panel
Coaxial feed from
TV antenna
If you are not using
cable/satellite box,
please refer to the
instruction manual.
Menu
1. Input/Output Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Remote Controller Setup
9. Lock Setup
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
1–2. HDMI Input
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
HDMI1
HDMI2
HDMI3
HDMI4
FRONT
L
R
COAXIAL
DIGITAL
OUT
VIDEO
OUT
AUDI O
OUT
Cable/
satellite
Using the Digital Inputs
If there’s no sound, you’ll need to assign the
digital inputs as necessary.
If you connect your DVD player to the AV
receiver’s DIGITAL COAXIAL IN 1, and connect
your cable/satellite receiver to the DIGITAL
COAXIAL IN 3, as shown, it’s not necessary to
change the default assignments.
If there’s no picture on your TV, set the
“Monitor Out” setting to “Analog” by pressing
the [Monitor Out] button first.
Antenna input
(e.g..RF IN)
On the front panel
Coaxial feed from
TV antenna
If you are not using
cable/satellite box,
please refer to the
instruction manual.
Menu
1. Input/Output Assign
2. Speaker Setup
3. Audio Adjust
4. Source Setup
5. Listening Mode Preset
6. Miscellaneous
7. Hardware Setup
8. Remote Controller Setup
9. Lock Setup
1. Input/Output Assign
1. Monitor Out
2. HDMI Input
3. Component Video Input
4. Digital Audio Input
1–4. Digital Audio Input
DVD/BD
VCR/DVR
CBL/SAT
GAME
AUX
COAX 1
COAX 2
COAX 3
OPT 1
FRONT
Loading...