Loading...
Integra® |
USER’S MANUAL |
Camino® ICP Monitor
Intracranial Pressure and Temperature Monitor
Caution
Federal (USA) law restricts this device to sale by or on the order of a physician.
|
Publication Name |
|
Integra Camino ICP Monitor User’s Manual |
|
Integra Part Number 60903733 Rev. B |
|
Effective Date September 2012 |
|
Trademark Acknowledgements |
|
Integra, the Integra logo, and Camino are registered trademarks of Integra |
|
LifeSciences Corporation or its subsidiaries in the United States and/or |
|
other countries. Delta-Cal is a trademark of Utah Medical Products, Inc. |
|
Sani-Cloth is a registered trademark of Professional Disposables |
|
International, Inc. Aptimax, Sealsure, and Sterrad are registered trademarks |
|
of Johnson and Johnson. Tyvec is a registered trademark of E.I. duPont. |
|
Kimguard and One-Step are registered trademarks of Kimberly-Clark |
|
Worldwide, Inc. |
0086 |
Copyright Information |
©2012 Integra LifeSciences Corporation. All rights reserved. |
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means—electronic, mechanical, photocopying, recording, or otherwise—without the expressed, written consent of Integra LifeSciences Corporation. Additional copies of this document can be ordered from Integra LifeSciences Corporation.
Manufacturer:
Integra LifeSciences(Ireland) Limited
IDA Business and Technology Park
Sragh, Tullamore, County Offaly, Ireland
Distributed by:
Integra LifeSciences Corporation 311 Enterprise Drive
Plainsboro, NJ 08536 USA
Tel: 1-800-654-2873 (USA only) 1-(609) 275-0500
Fax: 1-609-275-5363
Internet Address: http://www.integralife.com
Made in Ireland. Printed in Ireland.
This page is intentionally left blank.
TABLE OF CONTENTS |
|
List of Symbols and Abbreviations |
|
Packaging and Label Symbols................................................................................................................ |
v |
Software Symbols .................................................................................................................................. |
vi |
List of Abbreviations.............................................................................................................................. |
vii |
Chapter 1: System Overview |
|
Indications for Use / Intended Use .......................................................................................................... |
1 |
Contraindications .................................................................................................................................... |
1 |
Intended User.......................................................................................................................................... |
1 |
Intended Patient Population .................................................................................................................... |
1 |
Description of the Integra Camino ICP Monitor....................................................................................... |
2 |
Key Functions of Monitor................................................................................................................ |
2 |
Reviewing the User’s Manual.................................................................................................................. |
2 |
List of Warnings for Using the Monitor .................................................................................................... |
3 |
Parts of the Monitor................................................................................................................................. |
6 |
About the Front Panel..................................................................................................................... |
6 |
About the Rear Panel ..................................................................................................................... |
7 |
About the Right Panel..................................................................................................................... |
8 |
About the Bottom Panel.................................................................................................................. |
9 |
About the Left Panel ....................................................................................................................... |
9 |
Chapter 2: Setting Up System for the First Time |
|
Procedures for Initial Setup................................................................................................................... |
11 |
Chapter 3: Setting Up System for Clinical Use |
|
Setting Up System for Clinical Use ....................................................................................................... |
19 |
Positioning the Monitor ................................................................................................................. |
19 |
Attaching to Equipment Pole (if applicable).................................................................................. |
19 |
Powering the System On and Off ................................................................................................. |
20 |
Using the Battery for Power.......................................................................................................... |
21 |
Storing the Battery........................................................................................................................ |
22 |
About the Integra Catheters .................................................................................................................. |
23 |
Connecting the Integra® Camino® Fiber Optic Catheters (110-4 Series) .............................................. |
24 |
Connecting the Integra® Camino® Flex Catheters ................................................................................. |
27 |
Connecting to a Patient Bedside Monitor (if applicable) ...................................................................... |
30 |
i
Procedures for Synchronizing the Two Monitors ......................................................................... |
30 |
About Pressure and Temperature Measurements on the Patient Bedside Monitor..................... |
33 |
Storing the System ............................................................................................................................... |
33 |
Chapter 4: Monitoring the Patient’s ICP and Temperature |
|
About the Touch Screen....................................................................................................................... |
35 |
About the Synchronize to Monitor Button .................................................................................... |
36 |
Reviewing the Status Bar............................................................................................................. |
36 |
Verifying Status of Battery and AC Power .................................................................................. |
36 |
Verifying Amount of Battery Charge Available............................................................................. |
37 |
About the Alarms .................................................................................................................................. |
37 |
Monitoring the Patient’s ICP and Temperature .................................................................................... |
37 |
Monitoring Trend Data.......................................................................................................................... |
39 |
Conditions that Reset Trend Data................................................................................................ |
40 |
Setting the High ICP Alarm Limit .......................................................................................................... |
41 |
Specifying the High ICP Alarm Limit ............................................................................................ |
42 |
Disabling the High ICP Alarm ...................................................................................................... |
43 |
Silencing the High ICP Alarm Temporarily................................................................................... |
43 |
Restoring Default High ICP Alarm Limit Values........................................................................... |
43 |
Customizing the User Settings ............................................................................................................. |
44 |
Chapter 5: Responding to Physiological and Technical Alarms |
|
About the Two Alarm Types ................................................................................................................. |
47 |
About the Technical Messages ............................................................................................................ |
47 |
Understanding the Alarm Symbols ....................................................................................................... |
48 |
How the Monitor Prioritizes the Alarms ............................................................................................... |
48 |
Audio and Visual Indicators for Medium and Low Priority Alarms ............................................... |
49 |
Priorities of Physiological and Technical Alarms ......................................................................... |
49 |
List of Priorities for Each Alarm.................................................................................................... |
50 |
Responding to the Physiological Alarm (ICP above alarm limit) .......................................................... |
51 |
Responding to Technical Alarms.......................................................................................................... |
51 |
Responding to Irreversible System Failure Alarms...................................................................... |
51 |
Responding to ICP Catheter Failure Alarm.................................................................................. |
52 |
Responding to Temperature Sensor Failure Alarm ..................................................................... |
52 |
Responding to Low Battery Alarm ............................................................................................... |
52 |
Responding to Monitor Overheating Alarm.................................................................................. |
53 |
Responding to Cooling Fan Failure Alarm ................................................................................... |
53 |
Responding to Accuracy Range Alarm ........................................................................................ |
54 |
Responding to Battery Failure Alarm ........................................................................................... |
55 |
ii
Chapter 6: Extracting Trend Data for Remote Evaluation |
|
About Data Extraction ........................................................................................................................... |
57 |
Extracting Data to USB Drive ............................................................................................................... |
57 |
How the Monitor Stores Trend Data for Up to 5 Days .................................................................. |
58 |
Extract Data via Digital Streaming ........................................................................................................ |
59 |
Conditions That Reset Trend Data During Recording........................................................................... |
59 |
Chapter 7: Cleaning and Sterilizing the System |
|
Cleaning the System and Components................................................................................................. |
61 |
Cleaning Guidelines ..................................................................................................................... |
61 |
Sterilizing the Integra® Camino® Fiber Optic Catheter Cable ................................................................ |
63 |
Sterilizing the Integra® Camino® Flex Extension Cable ......................................................................... |
65 |
Sterilization Parameters ............................................................................................................... |
65 |
About Single-Use Only Catheters ......................................................................................................... |
66 |
Disposal of the Monitor System and Components ................................................................................ |
66 |
Chapter 8: Troubleshooting the System |
|
About the Troubleshooting Process ...................................................................................................... |
67 |
Responding to System Status Messages ............................................................................................. |
67 |
Responding to Problems During Use.................................................................................................... |
69 |
Responding to System Failure Messages............................................................................................. |
73 |
Chapter 9: Testing and Preventive Maintenance |
|
About These Procedures ...................................................................................................................... |
75 |
Use Fiber Optic Catheters for Each Test...................................................................................... |
75 |
Testing Pressure Input .......................................................................................................................... |
76 |
Using a Graduated Drainage Bag ................................................................................................ |
76 |
Using a Pressure Simulator (preferred method)........................................................................... |
78 |
Testing Pressure Output ....................................................................................................................... |
79 |
Testing Temperature Input.................................................................................................................... |
80 |
Testing Temperature Output ................................................................................................................. |
81 |
Testing High ICP Alarm Limit ................................................................................................................ |
84 |
Testing AC Power and Battery Charge ................................................................................................. |
85 |
AC Power ..................................................................................................................................... |
85 |
Low Battery Alarm ........................................................................................................................ |
85 |
Battery Charge ............................................................................................................................. |
86 |
Inserting A New Battery ........................................................................................................................ |
86 |
Determining Software Version .............................................................................................................. |
87 |
iii
Testing Synchronizing to Patient Bedside Monitor ............................................................................... |
87 |
Chapter 10: Contacting Integra for Technical Support and Annual Maintenance |
|
About Technical Support ...................................................................................................................... |
89 |
About Annual Maintenance .................................................................................................................. |
89 |
Appendix A: Technical Specifications |
|
List of Technical Specifications ............................................................................................................ |
91 |
Classifications and Standards ............................................................................................................. |
93 |
Manufacturer’s Declaration Table......................................................................................................... |
94 |
General Notes.............................................................................................................................. |
94 |
Appendix B: Integra Warranty |
|
Warranty .............................................................................................................................................. |
99 |
Index .............................................................................................................................. |
103 |
iv
LIST OF SYMBOLS AND ABBREVIATIONS
Packaging and Label Symbols
Symbol |
Definition |
|
Symbol |
Definition |
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Follow instructions for use |
|
|
|
|
|
|
|
|
|
|
|
|
Defibrillation-proof type CF applied part |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Catalogue number |
|
|
|
|
|
|
|
|
|
|
|
|
Direct current |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Caution: Federal (USA) law restricts this |
|
|
|
|
|
|
|
|
|
|
|
|
Class II equipment |
|
|
|
|
device to sale by or on the order of a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
physician. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Serial number |
|
|
|
|
|
|
|
|
|
|
|
|
Waste Electronics and Electrical |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Equipment |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Batch code |
|
|
|
|
|
|
|
|
|
|
|
|
USB connection |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Manufacturer |
|
|
|
|
|
|
|
|
|
|
|
|
Safety information for transporting |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
lithium ion batteries. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Date of manufacture |
|
|
|
CALIBRATION |
Due date for annual maintenance |
|||||||||
|
|
|
|
|
|
|
|
VERIFIED. |
|
|
|||||||
|
|
|
|
|
|
NEXT SCHEDULED |
|
|
|||||||||
|
|
|
|
|
MAINTENANCE DUE |
|
|
||||||||||
|
|
|
|
|
|
|
|
|
72903759 Rev 1 |
|
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
+50°C |
Temperature limitation |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
-20°Cl |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
List of Symbols and Abbreviations • v
Software Symbols
Symbol |
Description |
|
Symbol |
Definition |
|
|
|
|
|
|
|
|
|
|
|
Active alarm |
|
|
AC power not being used/available |
|
|
|
|
|
|
Audio paused |
|
|
Battery charge indicator |
|
|
|
|
|
|
Inactive alarm |
|
|
No battery connected or faulty battery |
|
|
|
|
|
|
High ICP alarm limit |
|
|
Battery being charged |
|
|
|
|
|
|
AC power being used |
|
|
System information panel |
|
|
|
|
|
|
On/Off power |
|
|
|
|
|
|
|
|
vi • List of Symbols and Abbreviations
List of Abbreviations
Abbreviation |
Definition |
|
|
|
|
AC |
Alternating Current |
|
|
ºC |
Celsius |
|
|
CAMCABL |
Preamplification cable used with Integra fiber optic catheters |
|
|
CSV |
Comma-separated values |
|
|
CT |
Computer tomography |
|
|
dB |
Decibels |
|
|
DC |
Direct Current |
|
|
DMM |
Digital Multimeter |
|
|
EtO |
Ethylene oxide |
|
|
ºF |
Fahrenheit |
FLEX |
Flex Catheter |
|
|
FLEXEXT |
Flex Extension Cable |
|
|
hPA |
Hectopascal pressure unit |
|
|
ICP |
Intracranial pressure |
|
|
ICT |
Intracranial temperature |
|
|
IPA |
Isopropyl alcohol |
|
|
LED |
Light Emmitting Diode |
|
|
mm |
Millimeters |
|
|
mmHg |
Millimeters of mercury |
|
|
MR |
Magnetic resonance |
|
|
OR |
Operating Room |
|
|
PMIO |
Patient Monitor Input Output |
|
|
TBI |
Traumatic brain injury |
|
|
USB |
Universal Serial Bus |
|
|
V |
Volt |
|
|
W |
Watt |
|
|
List of Symbols and Abbreviations • vii
This page is intentionally left blank.
viii • List of Symbols and Abbreviations
CHAPTER 1 SYSTEM OVERVIEW
Indications for Use / Intended Use................................................................. |
1 |
Contraindications ............................................................................................ |
1 |
Intended User................................................................................................... |
1 |
Intended Patient Population ........................................................................... |
1 |
Description of the Integra Camino ICP Monitor............................................ |
2 |
Reviewing the User’s Manual ......................................................................... |
2 |
List of Warnings for Using the Monitor ......................................................... |
3 |
Parts of the Monitor......................................................................................... |
6 |
Indications for Use / Intended Use
The Integra® Camino® ICP Monitor is indicated for use by qualified neurosurgeons or neurointensivists for measurement of intracranial pressure and temperature.
Contraindications
The Integra Camino ICP Monitor and its accessories are contraindicated for use in a Magnetic Resonance (MR) environment.
Intended User
The Integra Camino ICP Monitor is intended to be used by the following qualified medical and biomedical professionals:
•A qualified neurosurgeon should perform the placement and handling of the catheters.
•Designated qualified hospital staff (e.g. neurosurgeon, nurse, intensivist, trauma physician, or physician’s assistant) should perform the operation of the monitor.
Chapter 9 provides instructions for testing and maintaining the monitor. The procedures in this chapter are intended to be performed by the hospital’s biomedical engineering staff.
Intended Patient Population
Patients undergoing treatment with this monitor under the cranial applications are expected to have had a TBI, undergone a major neurosurgical procedure, or some other traumatic, ischemic or hemorrhagic incident requiring controlled monitoring of ICP and brain temperature.
Chapter 1 • System Overview • 1
Description of the Integra Camino ICP Monitor
The Integra Camino ICP Monitor is a compact, portable device that provides tools for continuously determining and monitoring intracranial pressure (ICP) and intracranial temperature (ICT) directly in the brain, depending on which catheters are connected to the system. This monitor supports the following catheters:
•Series of Integra® Camino® Fiber Optic Catheters (110-4 series) for measuring both ICP and temperature.
•Integra® Camino® Flex Catheter for measuring ICP values.
All Integra catheters measure their respective values at the tip of the catheter. This design eliminates the need for a fluid-filled system to communicate pressure (and carry pressure waves) to an external transducer.
Key Functions of Monitor
During clinical use, the Integra Camino ICP Monitor provides several key functions to facilitate the process for monitoring and analyzing patient data:
•Touch screen interface for evaluating patient ICP/ICT data and setting patient parameters (see page 35)
•Physiological alarm that activates if the patient’s Mean ICP value exceeds a user-specified limit for more than 5 seconds (see page 41)
•Rechargeable lithium ion battery that supplies power to monitor during patient transport (see page 21)
•Storage of patient’s ICP trend data for up to 5 days (see page 39)
•Outputs for transferring patient data to a patient bedside monitor (see page 30)
•Outputs for extracting patient data to remote media types via USB drive or digital streaming (see page 57)
For instructions on using the Integra catheters, see the directions for use supplied with each respective catheter.
Reviewing the User’s Manual
Integra recommends that all physicians, nurses, and technicians who will be using, operating, and maintaining the Integra Camino ICP Monitor review this user’s manual prior to using the system. If there are additional questions after reading this manual, contact Integra.
2 • Chapter 1 • System Overview
List of Warnings for Using the Monitor
Failure to observe one or more of the following warnings could compromise patient safety or result in measurement errors.
Warnings
•Use of the Integra Camino ICP Monitor is restricted to one patient at a time.
•The Integra Camino ICP Monitor and its accessories are contraindicated for use in a Magnetic Resonance (MR) environment.
•Always verify the high ICP alarm limit is set appropriately for each patient prior to treatment.
•Selecting the Alarm Off feature on the Alarm panel will disable the high ICP alarm
limit indefinitely. Use caution if this feature is selected. To re-enable this alarm, press the Alarm On and Accept buttons.
•No modification of the Integra Camino ICP Monitor is allowed.
•The Integra Camino ICP Monitor is a sensitive electronic device. When using the monitor, always handle with care. If damage is suspected, contact Integra.
•Read the user’s manual from the patient bedside monitor’s manufacturer before connecting the Integra Camino ICP Monitor to a patient bedside monitor.
•To prevent injury to the patient, user, or other persons, or damage to the monitor, always verify that the monitor is clamped securely to the equipment pole.
•To reduce the risk of electric shock, do not disassemble the Integra Camino ICP Monitor. Refer all servicing to qualified service personnel at Integra.
•To prevent electrical shock, only use the AC power adapter supplied by Integra (REF # MONPWR). Using a different AC power adapter may not provide protection against electric shock.
•Danger - Possible explosion hazard if used in the presence of flammable anaesthetics.
•Only use Integra supplied accessories on the Integra Camino ICP Monitor. This applies in particular to catheters, catheter cables, battery, AC power adapter, and USB-to-R232 adapter cable.
•If the Integra Camino ICP Monitor loses power and shuts down while it is connected to a patient bedside monitor, do not use the ICP values on the patient bedside monitor for patient measurements; the ICP values on the patient bedside monitor will be invalid.
•Connect the monitor to an AC power supply immediately if the low battery alarm is activated.
Chapter 1 • System Overview • 3
Warnings
•When using the battery:
-Do not heat above 80 °C.
-Do not open battery.
-Do not dispose of in fire.
-Do not short circuit as battery may ignite, explode, leak, or get hot causing personal injury.
-Replace battery with same part number only (REF # BAT1001).
-Use of another battery may present a risk of fire or explosion.
•To prevent injury to the patient, user, or other persons, make sure that the battery cover is closed securely during monitor use.
•Do not connect an Integra Camino Fiber Optic Catheter and an Integra Camino Flex Catheter simultaneously to the monitor. The Integra Camino ICP Monitor is designed to report ICP measurements with either the Flex Catheter or Fiber Optic Catheter connected to the monitor, but not both together.
•To prevent possible patient injury resulting from incorrect ICP measurements, always perform the steps listed on page 23 before implanting a new Integra Camino Fiber Optic Catheter into the patient. In particular, always make sure to adjust the new Fiber Optic Catheter’s ICP value to zero before implantation while the catheter is in the air. Never attempt to re-zero a catheter while the catheter is inside the patient.
•Once the Integra Camino Fiber Optic Catheter has been zeroed to the Integra Camino ICP Monitor, do not replace the Fiber Optic Catheter Cable being used for patient measurement. Replacing the Fiber Optic Catheter Cable with another cable after the catheter has already been zeroed may result in inaccurate patient measurements.
•Once the Integra Camino Fiber Optic Catheter has been zeroed to the Integra Camino ICP Monitor, do not transfer this zeroed catheter to any other monitor. Transferring a zeroed catheter to a different monitor may result in inaccurate ICP measurements.
•To prevent possible patient injury resulting from incorrect ICP measurements, always perform each of the steps listed on page 26 before implanting a new Integra Camino Flex Catheter into the patient. In particular, always leave the Flex Catheter in the air until the monitor completes the autozero (i.e. initialization) process successfully.
•Once the Integra Camino Flex Catheter has been initialized (autozeroed) by the Integra Camino ICP Monitor, do not replace the Integra Camino Flex Extension Cable being used for patient measurement. Replacing the Flex Extension Cable with another cable after the Flex Catheter has already been initialized may result in inaccurate ICP measurements.
•Once the Integra Camino Flex Catheter has been initialized (i.e. autozeroed) by the Integra Camino ICP Monitor, do not transfer this initialized catheter to any other monitor. Transferring an initialized catheter to a different monitor may result in inaccurate ICP measurements.
4 • Chapter 1 • System Overview
Warnings
•The Integra Camino ICP Monitor will only store the Mean ICP data from the most recent 5 days. All stored trend data older than 5 days will be lost. If monitoring is continued for more than 5 days, placement of a new catheter under sterile conditions is recommended. Note that replacing a catheter will reset the trend data. Please extract any data that you wish to retain prior to replacing the catheter.
•Do not autoclave or immerse the Integra Camino ICP Monitor in liquid as damage may occur. If the monitor is exposed to liquids, turn off the unit, remove the AC power adapter, dry the unit thoroughly, and send to biomed staff for evaluation before reapplying power.
•Only use the cleaning agents listed in Chapter 7 for cleaning and disinfecting the Integra Camino ICP Monitor system. Using solvents or cleaning agents not listed in Chapter 7 may damage the plastic exterior of the Integra Camino ICP Monitor.
Chapter 1 • System Overview • 5
Parts of the Monitor
The Integra Camino ICP Monitor contains hardware, software, and electrical components that support specific Integra catheters for monitoring the patient’s ICP and temperature. The following section provides information on the different parts of the monitor.
About the Front Panel
1
2 
3 |
4 |
|
The front panel contains:
Number |
Item |
Description |
|
|
|
|
|
|
1 |
Handle |
Handle used for carrying the monitor. |
2 |
Power Status |
Green LED button that indicates the monitor is |
|
|
being powered by the AC power adapter. Note |
|
|
that this button does not illuminate if the monitor |
|
|
is being powered by the battery. |
3 |
Power Button |
Turns the monitor on and off. This button is |
|
|
illuminated when the power is on. |
4 |
Touch Screen |
Provides software tools for viewing data and |
|
|
controlling parameters for monitoring the |
|
|
patient’s ICP and ICT levels. |
6 • Chapter 1 • System Overview
About the Rear Panel
1
5
2
6
3
4
The rear panel contains:
Number |
Item |
Description |
|
|
|
|
|
|
1 |
USB Port |
Connection port for extracting trend data via |
|
|
USB transfer or digital streaming. |
2 |
AC Power Adapter Port |
Connection port for the AC power cord. |
3 |
PMIO Port |
Connection port for PMIO cable. This cable |
|
|
is used to connect the Integra Camino ICP |
|
|
Monitor to a patient bedside monitor. |
4 |
Pole Clamp |
Clamping system for securing monitor to an |
|
|
equipment pole. |
5 |
Air Vent |
Grated opening that allows air being |
|
|
circulated by the internal cooling fan to leave |
|
|
the monitor. |
6 |
Cable Strap |
Rubber strap used to secure AC power |
|
|
adapter during transport. |
Chapter 1 • System Overview • 7
About the Right Panel
1
2
3
The right panel contains:
Number |
Item |
Description |
|
|
|
|
|
|
1 |
Temperature Port |
Connection port for the temperature connector on |
|
|
the Fiber Optic Catheter Cable. |
2 |
Pressure Port |
Connection port for the ICP connector on the |
|
|
Integra Camino Flex Extension Cable (pressure |
|
|
only). |
3 |
Pressure Port |
Connection port for the ICP connector on the |
|
|
Fiber Optic Catheter Cable. |
8 • Chapter 1 • System Overview
About the Bottom Panel
1
2
The bottom panel contains:
Number |
Item |
Description |
|
|
|
|
|
|
1 |
Battery Door Cover |
Removable cover for accessing/replacing the |
|
|
14.4V lithium ion battery. |
2 |
Air Vent |
Grated opening that allows air being circulated |
|
|
by the internal cooling fan to leave the monitor. |
About the Left Panel
The left panel does not contain any usable connector ports or buttons.
Chapter 1 • System Overview • 9
This page is intentionally left blank.
10 • Chapter 1 • System Overview
CHAPTER 2 SETTING UP SYSTEM FOR THE FIRST TIME
Procedures for Initial Setup
Step 1: Unpack the System (REF # CAM02)
Remove the contents from the Integra® Camino® ICP Monitor shipping box and verify the following items are included.
Warning
Only use Integra supplied accessories on the Integra Camino ICP
Monitor. This applies in particular to catheters, catheter cables, battery,
AC power adapter, and USB-to-R232 adapter cable.
Content Description
•Integra Camino ICP Monitor
•Quantity = 1
•AC power adapter (18 V DC 
, 1.67 A, 30 W)
•REF # MONPWR
•Quantity = 1
•14.4 V lithium ion battery
•REF # BAT1001
•Quantity = 1
Chapter 2 • Setting Up System for the First Time • 11
Content Description
•Integra® PMIO patient bedside monitor cable
•REF # PMIOMPM
•Quantity = 1
•Integra® Camino® Fiber Optic Catheter Cable
•REF # CAMCABL
•Quantity = 1
•Integra® Camino® Flex Extension Cable
•REF # FLEXEXT
•Quantity = 1
•USB-to-RS232 adapter cable
•REF # EXPORTCAB
•Quantity = 1
•User manual
•REF # UM-CAM02XX
(where XX refers to the country’s language code)
•Quantity = 1
After unpacking the contents, inspect the shipment for any signs of damage or loss. If any damages are discovered, notify the carrier, the supplier, and retain all shipping cartons for examination.
12 • Chapter 2 • Setting Up System for the First Time
Step 2: Install the Battery
Perform the following steps with a Phillips screwdriver and the Integra-supplied 14.4 V lithium ion battery.
1.Make sure the monitor is unplugged and turned off.
2.Turn the monitor upside down so the handle is facing downward.
3.Remove the 2 screws to take off the battery cover.
4.Verify the Integra logo on the battery is facing up and insert the battery:
A. Align the battery’s connectors on the front of the battery to the connector slots on the monitor.
B. Slide the battery’s connector into the monitor’s connector slots until the battery is fully inserted into place.
5. Secure the battery cover to the monitor by re-inserting the two small screws.
Chapter 2 • Setting Up System for the First Time • 13
Step 3: Prepare the AC Power Adapter with Region-Specific Plug
1.Remove the AC power adapter from the package and attach the region-specific adapter plug to the backside of the AC power adapter.
|
|
|
|
|
|
|
US |
UK |
Europe |
Australia |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Region-Specific Adapter Plugs
Backside of AC power adapter
A.Align the two slots on the adapter plug over the two prongs on the AC power adapter.
Slots on |
|
adapter plug |
Prongs on AC power adapter |
|
B. Push the adapter plug down over the two prongs until the entire base of the plug sits flush against the AC power adapter.
14 • Chapter 2 • Setting Up System for the First Time
C. Gently slide the adapter plug forward until it snaps into place.
2.To remove the adapter plug, press the release button on the AC power adapter and pull the plug away from the adapter.
Press the release button to remove adapter plug
Step 4: Plug the Monitor into AC Power
Perform the following steps with the Integra-supplied AC power adapter:
1.Place the monitor on a flat surface.
2.Connect the AC power adapter to the Integra Camino ICP Monitor:
A.On the back of the monitor, attach the connector end of the AC power adapter into the port labeled Input: 18 V 
.
Connector end of
AC power adapter
B. Insert the plug end of the AC power adapter into a grounded AC wall outlet.
3.Turn on the monitor. On the front of the monitor, press the power button; the Integra Camino ICP Monitor will display the Integra logo before initiating the monitor setup process.
Chapter 2 • Setting Up System for the First Time • 15
4.After the initial setup process completes, the Integra Camino ICP Monitor sounds a one-second startup tone and displays the Main panel on the touch screen.
Caution
The purpose of the startup tone verifies that the audio alarms are functioning correctly. If this tone does not sound during the startup process, contact Integra for service.
Step 5: Set the Time and Date
1. On the touch screen, press the Settings tab and select Set Time and Date.
2.On the displayed panel, press the desired field (hour, minutes, date, month, or year) and use the arrows to specify the appropriate setting. Note that you may adjust each of these settings prior to accepting them in the following step.
3.Press Accept; the Integra Camino ICP Monitor will display the selected time/date on the touch screen.
Step 6: Specify the Language
1. On the touch screen, press the Settings tab (fourth tab from the left)
Settings tab
2. Press Set Language.
Set Language button 
16 • Chapter 2 • Setting Up System for the First Time
3.In the displayed Language: menu, use the arrows to select the desired language.
4.Press Accept; the Integra Camino ICP Monitor will display all of the text that appears on the touch screen in the selected language.
Step 7: Use AC Power to Charge the Battery to Full Capacity
1.Turn off the monitor. On the front of the monitor, press the power button.
2.Keep the Integra Camino ICP Monitor on AC power with the monitor turned off for 5 hours. This will re-charge the battery to full capacity.
3.After 5 hours, turn on the monitor by pressing the power button.
4.On the touch screen, view the battery power symbol on the status bar to verify the symbol displays four green bars; this indicates the battery has full charge.
Chapter 2 • Setting Up System for the First Time • 17
This page is intentionally left blank.
18 • Chapter 2 • Setting Up System for the First Time
CHAPTER 3 SETTING UP SYSTEM FOR CLINICAL USE
Setting Up System for Clinical Use.............................................................. |
19 |
About the Integra Catheters ......................................................................... |
23 |
Connecting the Integra® Camino® Fiber Optic Catheters (110-4 Series) 24 |
|
Connecting the Integra® Camino® Flex Catheters .................................... |
27 |
Connecting to a Patient Bedside Monitor (if applicable) ........................... |
30 |
Storing the System ........................................................................................ |
33 |
Setting Up System for Clinical Use
The following section contains instructions for positioning the monitor, powering the monitor, and connecting catheters to the monitor prior to clinical use.
Positioning the Monitor
The Integra® Camino® ICP Monitor is intended to be positioned on a hard flat surface or securely clamped to an equipment pole or bed support next to the patient. The distance between the patient and the monitor is restricted by the length of the Integra catheter cable. It is not permitted to extend the Integra catheter cable with non-Integra extension cables.
Caution
To prevent the monitor from overheating:
•Do not block the air vents on the rear and bottom of the unit
•Do not place the monitor on a soft or uneven surface, which may result in blockage of the monitor’s air vents. For example, do not place the monitor on the bed during patient transport.
Attaching to Equipment Pole (if applicable)
The Integra Camino ICP Monitor includes a clamp for attaching the monitor to an equipment pole. To attach:
1. On the rear of the monitor, fit the pole clamp around the equipment pole.
Chapter 3 • Setting Up System for Clinical Use • 19
Loading...