NOTE: An internet connection is required to set up the printer and download the
software driver.
FAQ
For frequently asked questions, go to
www.hp.com/support/colorljM454FAQ or scan the QR code.
IMPORTANT:
Follow Steps 1 - 2 on the
printer hardware setup
poster, then continue
with Step 3.
Set up the control panel
3.
After turning on the printer, wait for it to initialize. To navigate the non-touchscreen control panel, use the arrow
buttons and the OK button. To navigate the touchscreen control panel, use touch, swipe, and scroll gestures. Follow
the prompts on the control panel to congure Language, Country/Region, and Self-managed or IT-managed.
• Self-managed: Optimized default settings for most users that include guided setup and conguration steps
automaticupdates.
and
• IT-managed: Optimized default settings for eet manageability.
Follow additional prompts to complete control panel setup.
Settings are fully customizable after initial setup.
4. Download and install the software
NOTE: Do not connect the USB cable until you are prompted to do so.
Method 1: Download HP Easy Start (Windows and macOS)
HP Easy Start will detect the printer, assist with selecting the printer
connection type(USB, Wired, or Wireless), and install the software.
1. From the computer, go to 123.hp.com/laserjet, and click Download.
2. Run HP Easy Start.
3. When prompted to select a connection type, select the appropriate option
for the type of connection.
NOTE: If HP Easy Start does not detect the printer or the software does
not install automatically, go to Method 2: Manually download from printer support website (Windows).
Troubleshooting Tips Connect the printer to a wireless network (wireless models only)
The installation software might not detect the printer during wireless setup. Follow the steps below to connect the printer to the same wireless network
asthe computer.
Non-Touchscreen control panels
1. From your printer, disconnect the Ethernet cable if attached.
2. Reset Printer Network Settings from Printer Control Panel: OK >
Setup > Network setup > Restore Network Setting.
The Wireless light begins blinking.
3. Install the software using Method 1 or Method 2 above.
Method 2: Manually download from printer support website
(Windows)
1. From the computer, go to www.hp.com/support/colorljm454.
2. Select Software anddrivers.
3. Download the software for your printer model and operating system.
4. Launch the software le from the folder where the le was saved.
5. Follow the onscreen instructions to install the software.
6. When prompted to select a connection type, select the appropriate
option forthetype of connection.
Manually congure the IP address
See the printer user guide for information on how to manually congure
the IPaddress at www.hp.com/support/colorljm454.
Touchscreen control panels
1. From the Home screen on the printer control panel, swipe the tab at the
top of the screen downward to open the Dashboard, and then touch the
Wireless
2. Touch the Setup
3. Touch Wireless Settings.
4. Touch Wireless Setup Wizard.
5. Follow the display instructions to complete the setup.
6. Install the software using Method 1 or Method 2 above.
icon.
icon.
Mobile printing (Optional)
5.
Connect the mobile device to a wireless network
Print from a mobile device to a printer that is connected to a wireless router/
network. Connect the mobile device to the same wireless network as the
printer.
Use the HP Smart app to set up, print, and more.
1. Go to 123.hp.com or scan the QR code.
2. Install the HP Smart app.
3. Run the HP Smart app and follow the
onscreen instructions to connect, set up,
print, and more.
NOTE: The HP Smart app might not be available for all mobile operating
systems.
HP Roam
For information on using HP Roam mobile print app, go to
hp.com/go/roam on the mobile device.
Connect the mobile device using Wi-Fi Direct
(wireless printer models only)
Print using Wi-Fi Direct with no router/network connection needed.
1. Enable Wi-Fi Direct on your printer
Non-Touchscreen control panels
1. On the printer control panel, press the OK button, open the Setup
menu, and then open the Wi-Fi Direct
2. On the Wi-Fi Direct Details screen, open the Wi-Fi Direct Settings
menu. Press the arrow button to turn the Wi-Direct Status to On.
3. Take note of the Wi-Fi Direct name and Wi-Fi Direct password from
your printer control panel.
Touchscreen control panels
1. From the Home screen on the printer control panel, swipe the tab
at the top of the screen downward to open the Dashboard, and
then touch the Wi-Fi Direct
2. On the Wi-Fi Direct Details screen, open the Wi-Fi Direct Settings
menu. Touch the switch to turn the Wi-Direct Status to On.
3. Take note of the Wi-Fi Direct name and Wi-Fi Direct password from
your printer control panel.
icon.
menu.
2. Discover the printer from your device
1. From the mobile device, go to the device Settings menu, and
search for the Wi-Fi Direct name you found from the printer
control panel.
2. Select the correct printer name, and enter the Wi-Fi Direct
password ifprompted.
Learn more about mobile printing
The product supports AirPrint and Wi-Fi Direct. For more mobile printing information, go to
www.hp.com/go/LaserJetMobilePrinting or scan the QR code.
2
6.
Use HP ePrint via email to print documents by sending them as an email attachment to the printer’s email address from any email enabled device, even
from devices that are not on the same network.
To use HP ePrint via email, the printer must meet these requirements:
• The printer must be connected to a wired or wireless network and have Internet access.
• HP Web Services must be enabled on the printer, and the printer must be registered with HP Connected.
Set up HP ePrint via email (optional)
Enable HP Web Services
Non-Touchscreen control panels
1. After the printer is connected to the network, print a conguration
page andidentify the printer IP address.
2. At the computer, open a web browser and enter the printer
IPaddress into the address line. The HP Embedded Web Server
(EWS) opens.
3. Select the HP Web Services tab, click Setup, click Continue, and
then follow the onscreen instructions. The printer congures the
connection to the Internet. An information page prints, which
contains a printer code necessary to register the HP printer at
HPConnected.
4. Go to www.hpconnected.com to create an HP ePrint account and
complete thesetup process.
Troubleshooting
User guide
The user guide includes printer usage and troubleshooting information. It is
available on the Web:
1. Go to www.hp.com/support/colorljm454.
2. Select the printer if prompted, and then click User Guides.
Touchscreen control panels
1. From the Home screen on the printer control panel, swipe the tab
at the topof the screen downward to open the Dashboard, and
then touch the HPePrint
Open the following menus:
• ePrint
• Settings
• Enable Web Services
2. Read the terms of use agreement and touch Yes. The printer
enables Web Services, and then prints an information page.
Theinformation page contains a printer code necessary to register
the HP printer at HP Connected.
3. Go to www.hpconnected.com to create an HP ePrint account and
complete thesetup process.
icon.
Control panel help (touchscreen models only)
To access help topics, touch the Help button on the printer control panel.
Check for rmware updates
1. Go to www.hp.com/support/colorljm454.
2. Select the printer if prompted, and then click Software and Drivers.
3. The operating system is auto-detected. To select a dierent operating
system, click Change.
4. Select Firmware, and click the Download button.
To learn more about the printer, go to
www.hp.com/support/colorljM454FAQ or scan the QR code.
Additional support resources
For HP’s all-inclusive help for the printer, go to:
CATATA N: Diperlukan koneksi internet untuk menyiapkan printer dan mendownload
driver perangkat lunak.
Pertanyaan Umum
Untuk pertanyaan umum, kunjungi www.hp.com/support/colorljM454FAQ
atau pindai kode QR.
PENTING:
Ikuti Langkah 1-2 pada
poster kongurasi perangkat
keras printer, lalu lanjutkan
dengan Langkah 3.
Mengkongurasi panel kontrol
3.
Setelah menghidupkan printer, tunggu proses inisialisasi. Untuk menavigasikan panel kontrol bukan layar
sentuh, gunakan tombol panah dan tombol OK. Untuk menavigasikan panel kontrol layar sentuh, gunakan
gerakan sentuh, geser, dan gulir. Ikutiperintah pada panel kontrol untuk mengkongurasi Bahasa, Negara/
Kawasan, dan Dikelola sendiri atau Dikelola TI.
• Dikelola sendiri: Pengaturan default yang dioptimalkan untuk sebagian besar pengguna yang mencakup
langkah-langkah pengaturan dan kongurasi terpandu, serta pembaruan otomatis.
• Dikelola TI: Pengaturan default dioptimalkan untuk kemampuan pengelolaan cepat.
Ikuti perintah tambahan untuk menyelesaikan pengaturan panel kontrol.
Pengaturan dapat disesuaikan sepenuhnya setelah kongurasi awal.
4. Mendownload dan menginstal perangkat lunak
CATATA N: Jangan sambungkan kabel USB hingga diminta untuk melakukannya.
Metode 1: Download HP Easy Start (Windows dan macOS)
HP Easy Start akan mendeteksi printer, membantu memilih jenis
sambungan printer (USB, Berkabel, atau Nirkabel), dan menginstal
perangkat lunak.
1. Dari komputer, kunjungi 123.hp.com/laserjet, dan klik Download.
2. Jalankan HP Easy Start.
3. Bila diminta untuk memilih jenis sambungan, gunakan pilihan yang
tepat untuk jenis sambungan.
CATATA N: Jika HP Easy Start tidak mendeteksi printer atau perangkat
lunak tidak terinstal otomatis, lakukan Metode 2: Secara manual download dari situs web dukungan printer (Windows).
Kiat-kiat mengatasi masalah Sambungkan printer ke jaringan nirkabel (hanya model nirkabel)
Perangkat lunak penginstalan mungkin tidak mendeteksi printer selama pengaturan nirkabel. Ikuti langkah-langkah di bawah untuk
menyambungkan printer ke jaringan nirkabel yang sama dengan komputer.
Panel kontrol bukan layar sentuh
1. Dari printer, putuskan sambungan kabel Ethernet jika terpasang.
2. Mengatur Ulang Pengaturan Jaringan Printer dari Panel Kontrol
Printer: OK > Kongurasi > kongurasi Jaringan > Pulihkan Pengaturan Jaringan. Lampu nirkabel
mulai berkedip.
3. Instal perangkat lunak menggunakan Metode 1 atau
Metode 2 di atas.
Metode 2: Secara manual download dari situs web dukungan
printer (Windows)
1. Dari komputer, kunjungi www.hp.com/support/colorljm454.
2. Pilih Software anddrivers (Perangkat lunak dan driver).
3. Download perangkat lunak untuk model printer dan sistem operasi Anda.
4. Jalankan le perangkat lunak dari folder tempat menyimpan le.
5. Ikuti petunjuk di layar untuk menginstal perangkat lunak.
6. Bila diminta untuk memilih jenis sambungan, gunakan pilihan yang
tepat untuk jenis sambungan.
Mengkongurasi alamat IP secara manual
Lihat panduan pengguna printer untuk mendapatkan informasi
tentangcara mengkongurasi alamatIP secara manual di
www.hp.com/support/colorljm454.
Panel kontrol layar sentuh
1. Dari layar Awal pada panel kontrol printer, usap tab di bagian atas
layar ke arah bawah untuk membuka Dasbor, lalu sentuh ikon
5. Ikuti petunjuk tampilan untuk menyelesaikan
pengaturan.
6. Instal perangkat lunak menggunakan Metode 1 atau
Metode 2 di atas.
.
.
7
Pencetakan seluler (Opsional)
5.
Menyambungkan perangkat seluler ke jaringan nirkabel
Cetak dari perangkat seluler ke printer yang tersambung ke router/jaringan
nirkabel. Sambungkan perangkat seluler ke jaringan nirkabel yang sama
dengan printer.
Gunakan aplikasi HP Smart untuk mengkongurasi,
mencetak, dan lainnya.
1. Kunjungi 123.hp.com atau pindai kode QR.
2. Instal aplikasi HP Smart.
3. Jalankan aplikasi HP Smart dan ikuti petunjuk
di layar untuk menyambungkan, mengkongurasi, mencetak,
dan lainnya.
CATATA N: Aplikasi HP Smart mungkin tidak tersedia untuk semua sistem
operasi seluler.
HP Roam
Untuk informasi tentang penggunaan aplikasi cetak seluler HP Roam, kunjungi
hp.com/go/roam pada perangkat seluler.
Sambungkan perangkat seluler menggunakan Wi-Fi Direct
(hanya model printer nirkabel)
Cetak menggunakan Wi-Fi Direct dengan tanpa koneksi router/jaringan.
1. Aktifkan Wi-Fi Direct di printer Anda
Panel kontrol bukan layar sentuh
1. Pada panel kontrol printer, tekan tombol OK, buka menu
Pengaturan, lalu buka menu Wi-Fi Direct
2. Di layar Detail Wi-Fi Direct, buka menu Setelan Wi-Fi Direct.
Tekan tombol panah untuk mengaktifkan Status Wi-Direct ke On.
3. Catat nama Wi-Fi Direct dan kata sandi Wi-Fi Direct dari panel
kontrol printer.
Panel kontrol layar sentuh
1. Dari layar Awal pada panel kontrol printer, usap tab di bagian
atas layar ke arah bawah untuk membuka Dasbor, lalu sentuh
ikon Wi-Fi Direct
2. Di layar Detail Wi-Fi Direct, buka menu Setelan Wi-Fi Direct.
Sentuh sakelar untuk mengaktifkan Status Wi-Direct ke On.
3. Catat nama Wi-Fi Direct dan kata sandi Wi-Fi Direct dari panel
kontrol printer.
.
.
2. Temukan printer dari perangkat
1. Dari perangkat seluler, buka menu Setelan perangkat, dan cari
nama Wi-Fi Direct dari panel control printer.
2. Pilih nama printer yang benar, dan masukkan kata sandi
Wi-Fi Direct jika diminta.
Selengkapnya tentang pencetakan seluler
Produk ini mendukung AirPrint dan Wi-Fi Direct. Untuk informasi lebih lanjut tentang pencetakan
seluler, kunjungi www.hp.com/go/LaserJetMobilePrinting atau pindai kode QR.
8
6.
Gunakan HP ePrint via email untuk mencetak dokumen dengan mengirimnya sebagai lampiran email ke alamat email printer dari perangkat apa
pun yang mendukung email, bahkan dari perangkat di jaringan yang berbeda.
Untuk menggunakan HP ePrint via email, printer harus memenuhi persyaratan berikut ini:
• Printer harus disambungkan ke jaringan berkabel atau nirkabel dan memiliki akses Internet.
• HP Web Services harus diaktifkan di printer, dan printer harus terdaftar di HP Connected.
Mengkongurasi HP ePrint melalui email (opsional)
Mengaktifkan HP Web Services
Panel kontrol bukan layar sentuh
1. Setelah printer terhubung ke jaringan, cetak halaman kongurasi
dan temukan alamat IP printer.
2. Di komputer, buka browser web, lalu masukkan alamat IP printer ke
dalam baris alamat. HP Embedded Web Server (EWS) akan terbuka.
3. Pilih tab HP Web Services, klik Setup (Kongurasi), klik Continue
(Lanjutkan), lalu ikuti petunjuk di layar. Printer akan mengongurasi
koneksi ke internet. Halaman informasi berisi kode printer yang
diperlukan untuk mendaftarkan printer HP di HP Connected.
4. Buka www.hpconnected.com untuk membuat akun HP ePrint dan
selesaikan proses kongurasi.
Mengatasi masalah
Panduan pengguna
Panduan pengguna mencakup informasi tentang penggunaan dan cara
mengatasi masalah printer. Informasi ini tersedia di Web:
1. Kunjungi www.hp.com/support/colorljm454.
2. Pilih printer jika diminta, lalu klik User Guides (Panduan Pengguna).
Memeriksa pembaruan rmware
1. Kunjungi www.hp.com/support/colorljm454.
2. Pilih printer jika diminta, lalu klik Software and Drivers
(PerangkatLunak danDriver).
3. Sistem operasi terdeteksi otomatis. Untuk memilih sistem operasi
yang berbeda, klik Change (Ubah).
4. Pilih Firmware, lalu klik tombol Download.
Untuk mempelajari lebih lanjut tentang printer, kunjungi
www.hp.com/support/colorljM454FAQ atau pindai kode QR.
Panel kontrol layar sentuh
1. Dari layar Awal pada panel kontrol printer, usap tab di bagian atas
layar ke arah bawah untuk membuka Dasbor, lalu sentuh ikon
HPePrint
Buka menu berikut:
• ePrint
• Settings (Pengaturan)
• Enable Web Services (Aktifkan Layanan Web)
2. Baca persyaratan perjanjian penggunaan dan sentuh Yes (Ya).
Printer mengaktifkan Web Services (Layanan Web), lalu mencetak
halaman informasi. Halaman informasi berisi kode printer yang
diperlukan untuk mendaftarkan printer HPdi HP Connected.
3. Buka www.hpconnected.com untuk membuat akun HP ePrint dan
selesaikan proses kongurasi.
.
Bantuan panel kontrol (hanya model layar sentuh)
Untuk mengakses topik bantuan, sentuh tombol Help (Bantuan) pada
panel kontrol printer.
Sumber dukungan tambahan
Untuk bantuan secara menyeluruh dari HP terkait printer, kunjungi:
자주 묻는 질문은 www.hp.com/support/colorljM454FAQ으로
이동합니다. 또는 QR 코드를 스캔합니다.
제어판 설정
3.
프린터를 켠 후 초기화될 때까지 기다립니다. 비터치스크린에서 화살표 버튼과 확인 버튼을 사용하여
이동합니다. 터치 스크린 제어판을 탐색하려면 터치, 스와이프, 스크롤 제스처를 사용합니다. 제어판의
메시지에 따라 언어, 국가/지역 및 자가 관리 또는 IT 관리를 구성합니다.
• 자가 관리: 설정 안내와 구성 단계 및
설정입니다.
•IT 관리: 장비 관리성에 최적화된 기본 설정입니다.
추가 메시지에 따라 제어판 설치를 완료합니다.
설정은 초기 설정 후 모두 사용자 요구에 맞게 설정할 수 있습니다.
자동 업데이트
를 포함하여 대부분의 사용자에게 최적화된 기본
4. 소프트웨어 다운로드 및 설치
참고: 알림이 표시되기 전까지는 USB 케이블을 연결하지 마십시오.
방법 1: HP Easy Start 다운로드(Windows 및 macOS)
HP Easy Start는 프린터를 감지하고 프린터 연결 유형(USB, 유선 또는
무선)의 선택을 지원하며, 소프트웨어를 설치합니다.
1. 컴퓨터에서 123.hp.com/laserjet으로 이동한 다음 다운로드를
클릭합니다.
2. HP Easy Start를 실행합니다.
3. 연결 유형을 선택하라는 메시지가 표시되면 연결 유형에 적합한
옵션을 선택합니다.
참고: HPEasyStart가 프린터를 감지하지 못하거나 소프트웨어가
자동으로 설치되지 않는 경우에는 방법 2: 프린터 지원 웹 사이트
(Windows)에서 수동으로 다운로드합니다.
문제 해결팁 무선 네트워크에 프린터 연결(무선 모델만 해당)
무선 설치하는 동안 설치 소프트웨어가 프린터를 감지하지 못할 수도 있습니다. 아래의 단계에 따라 프린터를 컴퓨터와 동일한 무선 네트워크
에 연결합니다.
Non-Touchscreen 제어판
1. 프린터에서 부착된 이더넷 케이블을 분리합니다.
2. 다음과 같이 프린터 제어판에서 프린터 네트워크
설정을 재설정합니다. 확인>설치>네트워크 설치>
네트워크 설정 복구. 무선 표시등이 깜박입니다.
3. 위의 방법 1 또는 방법 2를 사용하여 소프트웨어를
설치합니다.
방법 2: 프린터 지원 웹 사이트(Windows)에서 수동으로
다운로드
1. 프린터에서, www.hp.com/support/colorljm454로 이동합니다.
2. 소프트웨어및드라이버를 선택합니다.
3. 해당 프린터 모델 및 운영 체제용 소프트웨어를 다운로드합니다.
4. 파일이 저장된 폴더에서 소프트웨어 파일을 실행합니다.
5. 화면의 안내에 따라 소프트웨어를 설치합니다.
6. 연결 유형을 선택하라는 메시지가 표시되면 연결 유형에 적합한 옵션을 선택합니다.
IP 주소 수동으로 구성
수동으로 IP 주소를 구성하는 방법에 대한 자세한 내용은 프린터 사용
설명서(www.hp.com/support/colorljm454)를 참조하십시오.
터치스크린 제어판
1. 프린터 제어판의 홈 화면에서 화면 상단의 탭을 아래로 밀어서
대시보드를 연 다음에 무선
2. 설치
3. 무선 설정를 누릅니다.
4. 무선 설정 마법사 항목을 누릅니다.
5. 디스플레이의 설명에 따라 설치를 완료합니다.
6. 위의 방법 1 또는 방법 2를 사용하여
아이콘을 누릅니다.
소프트웨어를 설치합니다.
아이콘을 누릅니다
10
모바일 인쇄(선택 사항)
5.
무선 네트워크에 모바일 장치 연결
모바일 장치에서 무선 라우터/네트워크에 연결되어 있는 프린터에
인쇄합니다. 모바일 장치를 프린터와 동일한 무선 네트워크에
연결합니다.
HPSmart 앱을 사용하여 연결, 설정 및 인쇄 등을
실시합니다.
1.123.hp.com로 이동하거나 QR 코드를
스캔합니다.
2. HP Smart 앱을 설치합니다.
3. HP Smart 앱을 실행하여 화면에 표시되는
안내에 따라 연결, 설정 및 인쇄 등을 실시합니다.
참고: HPSmart 앱을 모든 모바일 운영 체제에서 사용할 수 있는 것은
아닙니다.
HP 롬
HP Roam 모바일 인쇄 앱의 사용에 대한 내용은 모바일 장치의
hp.com/go/roam로 이동합니다.
Wi-Fi Direct를 사용하여 모바일 장치 연결
(무선 프린터 모델만 해당)
라우터/네트워크를 연결하지 않고 Wi-FiDirect를 사용하여 인쇄합니다.
1. 프린터에서 Wi-Fi Direct 기능 사용
Non-Touchscreen 제어판
1. 프린터 제어판에서 확인 버튼을 누르고 설정 메뉴를 연 다음 Wi-Fi Direct
2. Wi-Fi Direct 세부 사항 화면에서 Wi-Fi Direct 설정 메뉴를
엽니다. 화살표 버튼을 눌러 Wi-Direct Status를 켜기로
돌립니다.
3. 프린터 제어판에서 Wi-Fi Direct 이름 및 Wi-Fi Direct 암호에
주목합니다l.
터치스크린 제어판
1. 프린터 제어판 홈 화면에서 화면 상단에 있는 탭을 아래로
밀어 대시보드를 연 다음 Wi-FiDirect 아이콘 Wi-FiDirect
아이콘을 누릅니다.
2. Wi-Fi Direct 세부 사항 화면에서 Wi-Fi Direct 설정 메뉴를
엽니다. 스위치를 눌러 Wi-Direct Status를 켜기로 돌립니다.
3. 프린터 제어판에서 Wi-Fi Direct 이름 및 Wi-Fi Direct 암호에
주목합니다l.
메뉴를 엽니다.
2. 장치에서 프린터 찾기
1. 휴대장치에서 장치 설정으로 이동한 다음 프린터 제어판에서
확인한 Wi-FiDirect 이름을 검색합니다.
2. 정확한 프린터 이름을 선택한 후 메시지가 표시되면
Wi-FiDirect 암호를 입력합니다.
모바일 인쇄에 대해 자세히 알아보기
제품은 AirPrint 및 Wi-Fi Direct를 지원합니다. 자세한 모바일 인쇄 정보는
www.hp.com/go/LaserJetMobilePrinting로 이동하거나 QR 코드를 스캔합니다.
11
6.
이메일을 통한 HPePrint를 사용하면 장치가 동일한 네트워크 상에 없어도 이메일을 사용할 수 있는 모든 장치에서 프린터의 이메일 주소로
문서를 첨부 파일로 전송하여 인쇄할 수 있습니다.
이메일을 통한 HPePrint를 사용하려면 프린터가 다음 요구 사항을 충족해야 합니다.
• 프린터가 유선 또는 무선 네트워크에 연결되어 있고 인터넷에 접속되어야 합니다.
• 프린터에 HP 웹 서비스가 활성화되어 있어야 하며, HP Connected에 프린터가 등록되어 있어야 합니다.
이메일을 통한 HP ePrint 설정(선택 사항)
HP 웹 서비스 활성화
Non-Touchscreen 제어판
1. 프린터가 네트워크에 연결된 후에 구성 페이지를 인쇄하고
프린터 IP 주소를 식별합니다.
2. 컴퓨터에서 웹 브라우저를 열고 주소줄에 프린터 IP 주소를
입력합니다. HP Embedded WebServer(EWS)가 열립니다.
3. HP 웹 서비스 탭을 선택한 후 설치와 계속을 차례로 클릭한 다음
화면에 표시되는 안내에 다릅니다. 프린터가 인터넷에 대한
연결을 구성합니다. HP 프린터를 HP Connected에 등록하는
데 사용되는 프린터 코드가 포함되어 있는 정보 페이지가
인쇄됩니다.
4. www.hpconnected.com로 이동하여 HP ePrint 계정을 작성한 다음
설치 과정을 완료합니다.
문제 해결
사용 설명서
사용 설명서에 프린터 사용법 및 문제 해결 정보가 포함되어 있습니다.
웹에서 사용할 수 있습니다:
1. www.hp.com/support/colorljm454로 이동합니다.
2. 메시지가 표시되면 프린터를 선택하고 사용 설명서를 클릭합니다.
펌웨어 업데이트 확인
1. www.hp.com/support/colorljm454로 이동합니다.
2. 메시지가 표시되면 프린터를 선택하고 소프트웨어 및 드라이버를 클릭합니다.
3. 운영 체제가 자동 감지됩니다. 다른 운영 체제를 선택하려면, 변경을 클릭합니다.
4. 펌웨어를 선택하고 다운로드 버튼을 클릭합니다.
프린터에 대해 자세히 알아보려면,
www.hp.com/support/colorljM454FAQ로 이동하거나 QR 코드를
스캔합니다.
터치스크린 제어판
1. 프린터 제어판의 홈 화면에서 화면 상단의 탭을 아래로 밀어서
대시보드를 연 다음에 HPePrint 아이콘을 누릅니다.
다음 메뉴를 엽니다.
•ePrint
• 설정
• 웹 서비스 활성화
2. 사용 계약서의 조건을 읽은 다음 예를 누릅니다. 프린터에서
웹 서비스가 활성화되고 정보 페이지가 인쇄됩니다. 정보
페이지에는 HP 프린터를 HP Connected에 등록하는 데 사용되는
프린터 코드가 있습니다.
3. www.hpconnected.com로 이동하여 HP ePrint 계정을 작성한 다음
설치 과정을 완료합니다.
The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions containedherein.
Trademark Credits
Windows® is a U.S. registered trademark of Microsoft Corporation.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S.
and other countries.
macOS is a trademark of Apple Inc., registered in the U.S. and other countries.
AirPrint is a trademark of Apple Inc., registered in the U.S. and other countries.
此处包含的信息如有更改,恕不另行通知。
此类产品和服务附带的保修声明中明确规定了 HP 产品
和服务的所有保修事项。不得将本文的任何内容视为构
成附加保修。HP 不对本文档中的技术错误、编辑错误或
遗漏承担责任。
商标说明
Windows®是 Microsoft Corporation 在美国的注册商标。
Apple 和 Apple 徽标是 Apple Inc. 在美国和其它国家/地区
的注册商标
Mac OS 是 Apple Inc. 在美国和其他国家/地区的注册商标。
AirPrint 是 Apple Inc. 在美国和其他国家/地区的注册商标。
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.