HP HCPL-5301, HCPL-5300, HCPL-4506, HCPL-0466, HCNW4506 Datasheet

H

Intelligent Power Module and

Gate Drive Interface Optocouplers

Technical Data

Features

•Performance Specified for Common IPM Applications

over Industrial Temperature Range: -40°C to 100°C

•Fast Maximum Propagation Delays

tPHL = 400 ns tPLH = 550 ns

•Minimized Pulse Width Distortion (PWD = 450 ns)

•15 kV/μs Minimum Common Mode Transient Immunity at VCM = 1500 V

•CTR > 44% at IF = 10 mA

•Safety Approval

UL Recognized - 2500 V rms for 1 minute (5000 V rms for 1 minute for HCNW4506 and HCPL-4506 Option 020) per UL1577

CSA Approved

VDE 0884 Approved

-VIORM = 630 V peak for HCPL-4506 Option 060

-VIORM = 1414 V peak for HCNW4506

BSI Certified (HCNW4506)

Applications

•IPM Isolation

•Isolated IGBT/MOSFET Gate Drive

•AC and Brushless DC Motor Drives

•Industrial Inverters

Description

The HCPL-4506 and HCPL-0466 contain a GaAsP LED while the HCNW4506 contains an AlGaAs LED. The LED is optically coupled to an integrated high gain photo detector. Minimized propa-

Functional Diagram

NC 1

ANODE 2

CATHODE 3

NC 4

8	VCC
20 kΩ
7	VL
6	VO
5	GND
SHIELD

HCPL-4506

HCPL-0466

HCNW4506

gation delay difference between devices make these optocouplers excellent solutions for improving inverter efficiency through reduced switching dead time.

An on chip 20 kΩ output pull-up resistor can be enabled by shorting output pins 6 and 7, thus eliminating the need for an external pull-up resistor in common IPM applications. Specifications and performance plots are given for typical IPM applications.

Truth Table

LED VO

ON L

OFF H

Selection Guide

Operating Temperature
	TA [°C]			Single Channel Packages
			8-Pin DIP	Small Outline	Widebody
Min.		Max.	(300 Mil)	SO-8	(400 Mil)	Hermetic*
-40		100	HCPL-4506	HCPL-0466	HCNW4506
-55		125				HCPL-5300
						HCPL-5301

*Technical data for these products are on separate HP publications.

The connection of a 0.1 μF bypass capacitor between pins 5 and 8 is recommended.

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

5965-3603E

1-49

Ordering Information

Specify Part Number followed by Option Number (if desired).

Example:

HCPL-4506#XXX

020 = UL 5000 V rms/1 Minute Option*

060 = VDE 0884 VIORM = 630 V peak Option* 300 = Gull Wing Surface Mount Option†

500 = Tape and Reel Packaging Option

*For HCPL-4506 only. Combination of Option 020 and Option 060 is not available.

†Gull wing surface mount option applies to through hole parts only.

Option data sheets are available. Contact your Hewlett-Packard sales representative or authorized distributor for information.

Package Outline Drawings

					9.65	± 0.25												7.62	± 0.25
													(0.300						± 0.010)
		(0.380				± 0.010)
TYPE NUMBER			8 7			6	5				OPTION CODE*							6.35		± 0.25
													(0.250							± 0.010)
											DATE CODE
					HP XXXXZ

YYWW

UR

UL

1

2

3

4

RECOGNITION

1.19 (0.047) MAX.

1.78 (0.070) MAX.

5° TYP.

0.254

+ 0.076

- 0.051

(0.010

+ 0.003)

- 0.002)

4.70 (0.185) MAX.

0.51 (0.020) MIN.

2.92 (0.115) MIN.

DIMENSIONS IN MILLIMETERS AND (INCHES).

1.080 ± 0.320

0.65 (0.025) MAX.

* MARKING CODE LETTER FOR OPTION NUMBERS.

(0.043 ± 0.013)

2.54 ± 0.25

"L" = OPTION 020

"V" = OPTION 060

(0.100 ± 0.010)

OPTION NUMBERS 300 AND 500 NOT MARKED.

Figure 1. HCPL-4506 Outline Drawing (Standard DIP Package).

					PAD LOCATION (FOR REFERENCE ONLY)
	9.65 ± 0.25				1.016 (0.040)
	(0.380 ± 0.010)				1.194 (0.047)
8	7	6	5		4.826
						TYP.
					(0.190)
			6.350 ± 0.25
			(0.250 ± 0.010)			9.398 (0.370)
						9.906 (0.390)
1	2	3	4
						0.381 (0.015)
					1.194 (0.047)	0.635 (0.025)
					1.778 (0.070)
			1.780		9.65 ± 0.25
1.19			(0.070)		(0.380 ± 0.010)
(0.047)			MAX.		7.62 ± 0.25
MAX.					(0.300 ± 0.010)
			4.19	MAX.		0.254	+ 0.076
							- 0.051
			(0.165)				+ 0.003)
						(0.010
							- 0.002)

1.080	± 0.320																							0.635 ± 0.25
(0.043	± 0.013)																							(0.025 ± 0.010)					12° NOM.
							2.54				0.635		± 0.130
	(0.100)										(0.025		± 0.005)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

Figure 2. HCPL-4506 Gull Wing Surface Mount Option #300 Outline Drawing.

1-50

8

7

6

5

5.842 ± 0.203

XXX

(0.236 ± 0.008)

3.937 ± 0.127

TYPE NUMBER

YWW

(0.155 ± 0.005)

(LAST 3 DIGITS)

DATE CODE

1

2

3

4

0.381 ± 0.076

1.270 BSG

(0.016 ± 0.003)

(0.050)

5.080 ± 0.127

7°

45° X

0.432

(0.200 ± 0.005)

(0.017)

3.175 ± 0.127

0.228 ± 0.025

(0.125 ± 0.005)

1.524

(0.060)

(0.009 ± 0.001)

0.152 ± 0.051

(0.006 ± 0.002)

DIMENSIONS IN MILLIMETERS (INCHES).

0.305

MIN.

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

(0.012)

Figure 3. HCPL-0466 Outline Drawing (8-Pin Small Outline Package).

Pin Location (for reference only)

							11.15 ± 0.15																																					11.00 MAX.
						(0.442 ± 0.006)																											(0.433)
																																	9.00 ± 0.15
				8						7							6							5							TYPE NUMBER											(0.354 ± 0.006)
													HP
																															DATE CODE
					HCNWXXXX
												YYWW
				1						2							3							4
																																									10.16 (0.400)
																										1.55																		TYP.
																								(0.061)																				7° TYP.												+ 0.076
																										MAX.																													0.254	- 0.0051
																																								(0.010																+ 0.003)
																																																								- 0.002)
																																	5.10
																																			(0.201) MAX.
																															3.10 (0.122)
																															3.90 (0.154)		0.51 (0.021) MIN.
2.54 (0.100)
TYP.
1.78 ± 0.15																									0.40 (0.016)										DIMENSIONS IN MILLIMETERS (INCHES).
(0.070 ± 0.006)																													0.56 (0.022)

Figure 4a. HCNW4506 Outline Drawing (8-Pin Widebody Package).

	11.15 ± 0.15				PAD LOCATION (FOR REFERENCE ONLY)
	(0.442 ± 0.006)
8	7	6	5
							6.15	TYP.
							(0.242)
				9.00 ± 0.15
				(0.354 ± 0.006)				12.30 ± 0.30
								(0.484 ± 0.012)
1	2	3	4
						1.3	0.9
						(0.051)	(0.035)
				1.55		12.30 ± 0.30
				(0.061)
						(0.484 ± 0.012)
				MAX.
						11.00
							MAX.
						(0.433)
				4.00	MAX.
				(0.158)
1.78 ± 0.15						1.00 ± 0.15
(0.070 ± 0.006)
				0.75 ± 0.25		(0.039 ± 0.006)		+ 0.076
		2.54
				(0.030 ± 0.010)				0.254 - 0.0051
		(0.100)
		BSC						+ 0.003)
DIMENSIONS IN MILLIMETERS (INCHES).								(0.010 - 0.002)
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).							7° NOM.

Figure 4b. HCNW4506 Outline Drawing (8-Pin Widebody Package with Gull Wing Surface Mount Option 300).

1-51

Solder Reflow Temperature Profile

	260
	240
																																																					T = 145°C, 1°C/SEC
	220
				T = 115°C, 0.3°C/SEC
	200
°C
	180
–	160
TEMPERATURE
	60
	140
	120
	100
	80
								T = 100°C, 1.5°C/SEC
	40
	20
	0
	0			1	2			3		4									5									6			7							8							9							10							11							12

TIME – MINUTES

Note: Use of nonchlorine activated fluxes is recommended.

Regulatory Information	CSA
The devices contained in this data	Approved under CSA Component
sheet have been approved by the	Acceptance Notice #5, File CA
following organizations:	88324.

UL	VDE
Recognized under UL 1577,	Approved according to VDE
Component Recognition	0884/06.92 (HCNW4506 and
Program, File E55361.	HCPL-4506 Option 060 only).

BSI

Certification according to BS451:1994

(BS EN60065:1994); BS EN60950:1992 (BS7002:1992) and

EN41003:1993 for Class II applications (HCNW4506 only).

Insulation and Safety Related Specifications

		8-Pin DIP		Widebody
		(300 Mil)	SO-8	(400 Mil)
Parameter	Symbol	Value	Value	Value	Units	Conditions
Minimum External	L(101)	7.1	4.9	9.6	mm	Measured from input terminals
Air Gap (External						to output terminals, shortest
Clearance)						distance through air.
Minimum External	L(102)	7.4	4.8	10.0	mm	Measured from input terminals
Tracking (External						to output terminals, shortest
Creepage)						distance path along body.
Minimum Internal		0.08	0.08	1.0	mm	Through insulation distance,
Plastic Gap						conductor to conductor, usually
(Internal Clearance)						the direct distance between the
						photoemitter and photodetector
						inside the optocoupler cavity.
Minimum Internal		NA	NA	4.0	mm	Measured from input terminals
Tracking (Internal						to output terminals, along
Creepage)						internal cavity.
Tracking Resistance	CTI	200	200	200	Volts	DIN IEC 112/VDE 0303 Part 1
(Comparative
Tracking Index)
Isolation Group		IIIa	IIIa	IIIa		Material Group
						(DIN VDE 0110, 1/89, Table 1)

Option 300 - surface mount classification is Class A in accordance with CECC 00802.

1-52

VDE 0884 Insulation Related Characteristics

(HCPL-4506 OPTION 060 ONLY)

Description	Symbol		Characteristic	Units
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage £ 300 V rms			I-IV
for rated mains voltage £ 450 V rms			I-III
Climatic Classification			55/100/21
Pollution Degree (DIN VDE 0110/1.89)			2
Maximum Working Insulation Voltage	VIORM		630	V peak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,	VPR		1181	V peak
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = VPR, Type and sample test,	VPR		945	V peak
tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec)	VIOTM		6000	V peak
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 18, Thermal Derating curve.)				°C
Case Temperature	TS		175
Input Current	IS,INPUT		230	mA
Output Power	PS,OUTPUT		600	mW
Insulation Resistance at T , V = 500 V	R	S	³ 109	W
S IO

VDE 0884 Insulation Related Characteristics (HCNW4506 ONLY)

Description	Symbol	Characteristic	Units
Installation classification per DIN VDE 0110/1.89, Table 1
for rated mains voltage £ 600 V rms		I-IV
for rated mains voltage £ 1000 V rms		I-III
Climatic Classification		55/100/21
Pollution Degree (DIN VDE 0110/1.89)		2
Maximum Working Insulation Voltage	VIORM	1414	V peak
Input to Output Test Voltage, Method b*
VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec,	VPR	2652	V peak
Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
VIORM x 1.5 = VPR, Type and sample test,	VPR	2121	V peak
tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec)	VIOTM	8000	V peak
Safety Limiting Values
(Maximum values allowed in the event of a failure,
also see Figure 18, Thermal Derating curve.)			°C
Case Temperature	TS	150
Input Current	IS,INPUT	400	mA
Output Power	PS,OUTPUT	700	mW
Insulation Resistance at TS, VIO = 500 V	RS	³ 109	W

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section (VDE 0884), for a detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.

1-53