HP HCPL-4504, HCPL-0454, HCNW4504 Datasheet

peak for

H

High CMR, High Speed

Optocouplers

Technical Data

Features

•Short Propagation Delays for TTL and IPM Applications

•15 kV/μs Minimum Common Mode Transient Immunity at

VCM = 1500 V for TTL/Load Drive

•High CTR at TA = 25°C

>25% for HCPL-4504/0454 >23% for HCNW4504

•Electrical Specifications for Common IPM Applications

•TTL Compatible

•Guaranteed Performance from 0°C to 70°C

•Open Collector Output

•Safety Approval

UL Recognized - 2500 V rms for 1 minute (5000 V rms for 1 minute for HCPL-4504#020 and HCNW4504)per UL1577

CSA Approved

VDE 0884 Approved

-VIORM = 630 V peak for HCPL-4504#060

-VIORM = 1414 V

HCNW4504

BSI Certified (HCNW4504)

•Available in 8-Pin DIP, SO-8, Widebody Packages

Applications

•Inverter Circuits and Intelligent Power Module (IPM) interfacing -

High Common Mode Transient Immunity (> 10 kV/μs for an

IPM load/drive) and (tPLH - tPHL) Specified (See Power Inverter Dead Time section)

•Line Receivers -

Short Propagation Delays and Low Input-Output Capacitance

•High Speed Logic Ground Isolation - TTL/TTL, TTL/ CMOS, TTL/LSTTL

•Replaces Pulse Transformers -

Save Board Space and Weight

•Analog Signal Ground Isolation -

Integrated Photodetector Provides Improved Linearity over Phototransistors

HCPL-4504

HCPL-0454

HCNW4504

Description

These optocouplers are similar to HP’s other high speed transistor optocouplers but with shorter propagation delays and higher CTR. The HCPL-4504/0454 and HCNW4504 also have a guaranteed propagation delay difference (tPLH - tPHL). These features make these optocouplers an excellent solution to IPM inverter dead time and other switching problems.

Functional Diagram

NC 1		8	VCC
ANODE 2		7	NC
CATHODE	3	6	VO
NC	4	5	GND

TRUTH TABLE

LED	VO
ON	LOW
OFF	HIGH

A 0.1 μF bypass capacitor between pins 5 and 8 is recommended.

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

5965-3604E

1-33

The HCPL-4504/0454 and HCNW4504 CTR, propagation delay, and CMR are specified for both TTL and IPM load/drive conditions. Specifications and typical performance plots for both TTL and IPM conditions are provided for ease of application.

These single channel, diodetransistor optocouplers are available in 8-Pin DIP, SO-8, and Widebody package configurations. An insulating layer between a LED and an integrated photodetector provide electrical insulation between input and output. Separate connections for

the photodiode bias and outputtransistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base collector capacitance.

Selection Guide

Single Channel Packages

8-Pin DIP	Small Outline	Widebody
(300 Mil)	SO-8	(400 Mil)
HCPL-4504	HCPL-0454	HCNW4504

Ordering Information

Specify Part Number followed by Option Number (if desired).

Example:

HCPL-4504#XXX

020 = UL 5000 V rms/1 Minute Option*

060 = VDE 0884 VIORM = 630 V peak Option* 300 = Gull Wing Surface Mount Option†

500 = Tape and Reel Packaging Option

Option data sheets available. Contact your Hewlett-Packard sales representative or authorized distributor for information.

*For HCPL-4504 only. Combination of Option 020 and Option 060 is not available. †Gull wing surface mount option applies to through hole parts only.

Schematic

ICC 8

VCC

+IF

	ANODE
	2
	VF	IO	6
	–
			VO
	CATHODE
	3
	SHIELD		5
			GND

1-34

Package Outline Drawings

8-Pin DIP Package (HCPL-4504)

9.65 ± 0.25

(0.380 ± 0.010)

TYPE NUMBER

8

7

6

5

OPTION CODE*

HP XXXXZ

DATE CODE

YYWW

UR

UL

1

2

3

4

RECOGNITION

1.19 (0.047) MAX.

1.78 (0.070) MAX.

4.70 (0.185) MAX.

0.51 (0.020) MIN.

2.92 (0.115) MIN.

1.080 ± 0.320

0.65 (0.025) MAX.

(0.043 ± 0.013)

2.54 ± 0.25

(0.100 ± 0.010)

7.62 ± 0.25

(0.300 ± 0.010)

6.35 ± 0.25

(0.250 ± 0.010)

5° TYP.				0.254	+ 0.076
					- 0.051
			(0.010		+ 0.003)
					- 0.002)

DIMENSIONS IN MILLIMETERS AND (INCHES).

* MARKING CODE LETTER FOR OPTION NUMBERS. "L" = OPTION 020

"V" = OPTION 060

OPTION NUMBERS 300 AND 500 NOT MARKED.

8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-4504)

																													PAD LOCATION (FOR REFERENCE ONLY)
							9.65 ± 0.25																																	1.016 (0.040)
						(0.380 ± 0.010)
																																															1.194 (0.047)
			8					7							6				5
																																																										4.826					TYP.
																																																										(0.190)
																									6.350 ± 0.25
																									(0.250 ± 0.010)																																						9.398 (0.370)
																																																															9.906 (0.390)
		1				2							3					4
																																																																0.381 (0.015)
																													1.194 (0.047)																																			0.635 (0.025)
																													1.778 (0.070)
																		1.780											9.65 ± 0.25
1.19																						(0.070)																						(0.380 ± 0.010)
																								MAX.																					7.62 ± 0.25
(0.047)
																																									(0.300 ± 0.010)
MAX.																																																																			+ 0.076
																																																																	0.254
																																																																			- 0.051
																									4.19			MAX.																																			(0.010				+ 0.003)
																		(0.165)
																																																																			- 0.002)

1.080	± 0.320
(0.043	± 0.013)																								0.635 ± 0.25
																							(0.025 ± 0.010)								12° NOM.
								2.54						0.635		± 0.130
	(0.100)													(0.025		± 0.005)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

1-35

Small Outline SO-8 Package (HCPL-0454)

										8				7					6			5
																								5.842 ± 0.203
																		XXX				(0.236 ± 0.008)
3.937	± 0.127																														TYPE NUMBER
																	YWW
(0.155	± 0.005)
																															(LAST 3 DIGITS)
																															DATE CODE
										1				2					3			4
0.381	± 0.076
(0.016	± 0.003)																											1.270		BSG
																						(0.050)
											5.080 ± 0.127																			7°				45° X		0.432
											(0.200 ± 0.005)																									(0.017)

3.175 ± 0.127

(0.125 ± 0.005) 1.524

(0.060)

0.152 ± 0.051

(0.006 ± 0.002)

DIMENSIONS IN MILLIMETERS (INCHES).	0.305	MIN.
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).	(0.012)

0.228 ± 0.025

(0.009 ± 0.001)

8-Pin Widebody DIP Package (HCNW4504)

						11.15 ± 0.15																						11.00
					(0.442 ± 0.006)																							(0.433) MAX.
																											9.00 ± 0.15
	8						7				6				5								(0.354 ± 0.006)
																				TYPE NUMBER
									HP											DATE CODE
					HCNWXXXX
									YYWW
	1						2				3				4
																										10.16 (0.400)
																												TYP.

1.55

(0.061)

MAX. 7° TYP. 0.254 + 0.076 - 0.0051

+ 0.003) (0.010 - 0.002)

																																					5.10 MAX.
																																			(0.201)
																														3.10 (0.122)
																															3.90 (0.154)				0.51 (0.021) MIN.
	2.54 (0.100)
	TYP.
1.78	± 0.15																						0.40 (0.016)														DIMENSIONS IN MILLIMETERS (INCHES).
(0.070	± 0.006)																												0.56 (0.022)

1-36

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW4504)

						11.15 ± 0.15
					(0.442 ± 0.006)																	PAD LOCATION (FOR REFERENCE ONLY)
																5
	8						7				6
																																						6.15			TYP.
																																						(0.242)
																			9.00 ± 0.15
																			(0.354 ± 0.006)
																																									12.30 ± 0.30
																																									(0.484 ± 0.012)
	1						2				3				4
																																						0.9
															1.3

(0.051)	(0.035)

1.78 ± 0.15

(0.070 ± 0.006)

																			1.55														12.30 ± 0.30
																						(0.061)																		(0.484 ± 0.012)
																							MAX.																		11.00 MAX.
																																			(0.433)
																								4.00				MAX.
																							(0.158)
																																							1.00 ± 0.15
																	2.54											0.75 ± 0.25								(0.039 ± 0.006)																+ 0.076
(0.100)																												(0.030 ± 0.010)																							0.254 - 0.0051
																	BSC																																		(0.010	+ 0.003)
DIMENSIONS IN MILLIMETERS (INCHES).																																																				- 0.002)
																																																7° NOM.

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

Solder Reflow Temperature Profile

(HCPL-0454 and Gull Wing Surface Mount Option Parts)

TEMPERATURE – °C

260

240

T = 145°C, 1°C/SEC

220

T = 115°C, 0.3°C/SEC

200

180

160

140

120

100

80

T = 100°C, 1.5°C/SEC

60

40

20

0

0

1

2

3

4

5

6

7

8

9

10

11

12

TIME – MINUTES

Note: Use of nonchlorine activated fluxes is highly recommended.

1-37