Installation Instructions for Top Mount Refrigerator
WARNING
To avoid electric shock, which can cause death or severe personal injury, do not connect your refrigerator to an electrical power source until you have completed Step 3 of these instructions.
Tools Necessary: |
|
|
NOTE |
|
|
|
|
(OR) |
|
OR |
These installation instructions are |
#2 Square |
|
|
provided only as a possible customer |
Bit |
|
|
option. We recommend you use a ser- |
or |
|
|
|
Quadrex Head |
Socket |
Adjustable |
vice or kitchen contracting professional |
Screwdriver |
Wrench Set |
Wrench |
to install your refrigerator. |
1 Prepare The Installation Site |
Include these minimum guidelines in your site preparation:
•Choose a place near a grounded electrical outlet.
•Do not use an extension cord or an adapter plug.
•Avoid direct sunlight and close proximity to a range, dishwasher or other heat source.
•Floor should be level and able to support a fully loaded refrigerator.
Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:
Sides & Top: 3/8 in.
Rear: 1 in.
NOTE
Information about cabinetry construction for your new appliance is available for contractors. Call 1-877-435-3287.
CAUTION
Room temperatures below 55°F (13°C) or above 110°F (43°C) will impair cooling ability of your refrigerator’s compressor.
2 Transport Refrigerator To Site
By now, you have already removed your refrigerator’s shipping carton. You may still need to use a hand truck to move it through close spaces or entrances. If the refrigerator is larger than an entrance, consider two options:
• Remove the entrance door if one exists.
• Remove the refrigerator doors (see how in your Use & Care Guide).
When using a hand truck: |
CAUTION |
• Do not run retaining straps over handles. |
|
• Load refrigerator from side of cabinet only. |
|
• Do not overtighten retaining straps. |
Shifting the refrigerator from side to |
• Never use refrigerator handles to move |
side may damage flooring. |
the refrigerator. |
|
• Remove packaging tape from doors only after the unit is in place.
3 Water Supply Connection
|
NOTE |
|
|
|
|
CAUTION |
|
Automatic ice makers are optional accessories that may |
|
|
|
||||
|
To avoid property damage: |
||||||
be installed in most at any time. Visit www.frigidaire. |
|
• |
Use a water supply line made of |
||||
com/Filters--Accessories/ Refrigerator-Accessories for |
|
||||||
information about Ice Maker Kit 117000. |
|
|
stainless steel tubing or polyline. |
||||
What you will need: |
|
|
• |
Ensure water supply complies with |
|||
House |
|
local plumbing codes. |
|||||
• Basic Tools: adjustable |
plumbing |
|
|
|
|||
line |
|
NOTE |
|||||
wrench, flat-blade screwdriver, |
|
|
|||||
and PhillipsTM screwdriver |
Water line hookup |
||||||
For homes with existing valves, Frigidaire |
|||||||
• Access to a household cold |
|||||||
|
|
|
® |
||||
water line with water pressure between 30 and 100 psi. |
recommends its Smart Choice water |
||||||
• A water supply line made of ¼ inch (6.4 mm) OD, |
line kit 5304437642 (with a 6 ft. stainless |
||||||
steel water line), and for homes without |
|||||||
copper or stainless steel tubing. To determine the |
an existing valve, Frigidaire recom- |
||||||
length of tubing needed, measure the distance |
mends its Smart Choice® water line kit |
||||||
from the ice maker inlet valve at the back of the |
5304493869 (with a 6 ft. polyline water |
||||||
refrigerator to your cold water pipe. Then add ap- |
line). Please refer to www.frigidaire.com/ |
||||||
proximately 7 feet (2.1 meters), so the refrigerator |
Filters--Accessories/Cleaning-Accessories |
||||||
can be moved out for cleaning (as shown). |
for more information. |
||||||
• A shutoff valve to connect the water supply line to |
|||||||
|
|
|
your household water system. DO NOT use a self-piercing type shutoff valve.
• Do not reuse compression fitting or use thread seal tape.
• A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve.
Not satisfied with the installation of your refrigerator?
To Connect Water Supply Line To the Ice Maker Inlet Valve:
1 Disconnect the refrigerator from the electric power source.
2Place the end of water supply line into a sink or a bucket. Turn ON the water supply and flush the supply line until the water is clear. Turn OFF the water supply at the shutoff valve.
3Remove the plastic cap from water valve inlet and discard the cap.
4If you use copper tubing, slide brass compression nut, and then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ in. / 6.4 mm). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another ½ turn with a wrench; DO NOT overtighten. See below.
If you use braided flexible stainless steel tubing, the nut is already assembled on the tubing. Slide nut onto valve inlet and finger tighten nut onto valve. Tighten another ½ turn with a wrench; DO NOT overtighten. See below.
5With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.
6Coil excess water supply line (copper tubing only), about 2½ turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.
7To turn ice maker on, press the ice maker’s On/Off power switch so the LED is steadily illuminated.
8Turn ON the water supply at the shutoff valve and tighten any connections that leak.
9 Reconnect refrigerator to an electrical power source.
Plastic Water |
|
Tubing |
|
Maker |
|
|
Brass |
|
Compression |
|
Nut |
|
Water Line |
|
Water Valve |
|
Bracket |
|
Valve Inlet |
|
Water Valve |
|
6 ft minimum (1.8 m) |
braided flexible stainless steel |
|
water line from household water supply |
|
Plastic Water |
Clamp |
Tubing to Ice |
Brass |
Maker Fill Tube |
|
|
Compression |
|
Nut |
|
Ferrule |
|
Sleeve |
|
Copper |
|
Line |
|
Water |
|
Valve |
|
Bracket |
|
Water |
|
Valve Inlet |
|
Water |
|
Valve |
|
Copper water line |
from household water supply |
NOTE
•The ice maker’s fill valve may operate noisily if the household water supply is shut off.
•After ensuring no water leaks exist at any connection, be sure to check for leaks again in 24 hours.
4 Final Positioning of Refrigerator
If possible, use a hand truck to position the refrigerator directly in front of its cabinet enclosure. Be careful not to move the refrigerator beyond its water supply (copper tubing) connections. Plug in the power cord, and push the refrigerator straight back into place.
|
|
|
|
|
|
|
CAUTION |
|
|
|
IMPORTANT |
|
|
||
|
|
|
|
|
|||
|
|
|
|
• |
Shifting the refrigerator from side to |
||
|
|
|
|
|
|||
If you are installing your refrigerator without |
|
|
side may damage flooring. |
||||
connecting it to a water supply (some models), |
|
• |
Do not block the lower front of your |
||||
make sure the ice maker’s power switch is turned |
|
|
refrigerator. Sufficient air circulation |
||||
Off (see the Use & Care Guide for more details). |
|
|
is essential for proper operation. |
•All 4 corners of the cabinet must rest firmly on the floor.
•The cabinet should be level at the front and rear.
•The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator.
Setting the Anti-tip device:
The Anti-tip brackets are located on the lower front corners of the cabinet. Lower the Anti-tip on each side clockwise until they contact the floor. Do not raise the cabinet.
Lower
Anti-Tip Bracket
WARNING
The anti-tip device must be installed according to the instructions in your Use & Care Manual. Failure to do so will result in injury.
B |
Hinge |
Pin |
|
|
Screws |
Hinge |
Center |
|
Door |
Hinge |
Door |
Stopper |
|
Hole |
|
||
Plug |
|
Stopper |
Screw |
Bottom Hinge
Pin
8 Installation Check off List |
Doors |
Ice Maker |
ȽȽ Handles are secure and tight (some models) ȽȽ Door seals completely to cabinet on all sides ȽȽ Freezer door is level across the top
Leveling
ȽȽ Refrigerator is level, side to side and tilted ¼ in. (6 mm) front to back
ȽȽ Cabinet is setting solid on all corners ȽȽ Anti-tip bracket set
Electrical Power
ȽȽ House power turned on ȽȽ Refrigerator plugged in
ȽȽ House water supply connected to refrigerator (ice maker installed)
ȽȽ No water leaks present at all connections - recheck in 24 hours
ȽȽ Ice Maker is turned ON (ice maker installed)
Final Checks
ȽȽ Shipping material removed
ȽȽ Fresh Food and Freezer controls set ȽȽ Crisper Humidity controls set
ȽȽ Registration Card sent in
Please contact the store from which you purchased your refrigerator. |
P/N: A14328801 |