7300 PRO
1
IMPORTANT SAFETY INSTRUCTIONS
Your 7300 sewing machine is designed and constructed for HOUSEHOLD use only. Read all
instructions before using this machine.
DANGER – To reduce the risk of electric shock:
1. Y our sewing machine should never be left unattended when plugged in. Always unplug the machine
from the electrical outlet immediately after using and before cleaning.
2. Always unplug before replacing light bulb. Replace bulb with same type rated 12 Volts, 5 watts.
3. Do not reach for the machine if it has fallen into water. Unplug immediately.
4. Do not place or store machine where it can fall or be pulled into a tub or sink. Do not place it in or
drop it into water or other liquid.
WARNING – To reduce the risk of burns, fire, electrical shock or injury:
1. Do not allow machine to be used as a toy. Supervision is necessary when this machine is used by
or near children.
2. Use this sewing machine only for its intended use as described in this manual. Only use
attachments recommended by the manufacturer as described in this manual.
3. Never operate this machine if it has a damaged cord or plug, is not working properly, has been
dropped or damaged or dropped into water. Return the machine to the nearest authorized dealer or
service center for examination, repair, electrical or mechanical adjustment.
4. This machine is equipped with a special connection cord which, if damaged, must be replaced by
an identical cord. This can be obtained from your dealer.
5. Never operate the sewing machine with any air opening blocked. Keep ventilation openings of the
sewing machine and foot control free from the accumulation of lint, dust and fibers.
6. Never drop or insert any object into any opening.
7. Do not use outdoors.
8. Do not operate where aerosol (spray) products are being used or where oxygen is being
administered.
9. To disconnect, turn machine off and remove plug from outlet.
10. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
11. Keep fingers away from all moving parts, especially the needle.
12. Always use the proper needle plate. The wrong plate can cause the needle to break.
13. Do not use bent needles.
14. Do not pull or push fabric while stitching. This may deflect the needle causing it to break.
15. Switch the sewing machine off when making any adjustment in the needle area, such as threading
needle, changing needle, threading bobbin, changing presser foot, etc.
16. Always unplug the sewing machine from the electrical outlet when removing covers, lubricating or
making any other servicing adjustments mentioned in the instruction manual.
SA VE THESE INSTRUCTIONS
IMPORTANT
Be sure to keep machine away from static electricity, heat sources, humidity and direct sunlight.
USA only
Your machine comes equipped with a polarized plug (one prong wider than the other). A polarized plug
reduces the risk of electrical shock. This plug is intended to fit into a polarized outlet. If the plug does
not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install
the proper outlet. Do not modify the plug in any way.
Use only foot control Model 21371 (UL, CSA).
2
TABLE OF CONTENTS
SECTION I – Machine Parts and Functions
Part Names.............................................................................. 3
Standard Accessories ............................................................. 4
Presser Foot and Accessory Definitions.............................. 5-6
How to Attach Stitch Chart Brackets....................................... 7
Stitch Chart .............................................................................. 7
Write ‘n Clip Board...................................................................7
Quilt Table ................................................................................ 8
Knee Lifter ............................................................................... 8
Connecting Machine to Power Supply .................................... 9
Main Function of Keys...........................................................10
Keyboard Selection Keys ................................................ 11-13
Setting Quick Resumption, Sound and
Language Modes ........................................................ 14-15
Controlling Sewing Speed.....................................................15
Foot Pressure Dial................................................................. 15
How to Drop the Feed Dog....................................................16
Presser Foot Lever ................................................................16
Additional Presser Foot Clearance ....................................... 16
Attaching and Removing Presser Feet ................................. 17
Attaching and Removing Shank............................................ 17
Setting for Dual Feed Sewing.......................................... 18-19
Seam Allowance Lines .......................................................... 20
Centimeter/Inch Quick Measurements.................................. 20
Adjusting Needle Thread Tension .........................................21
Using the Fine Adjustment Screw.........................................22
SECTION II – Getting Ready to Sew
Selecting the Correct Needle for Fabrics.............................. 23
Changing Needles ................................................................. 23
Needle Definitions .................................................................24
Winding a Bobbin ............................................................ 25-26
Inserting the Bobbin .............................................................. 27
Threading the Machine.................................................... 28-29
Built-in Needle Threader .......................................................30
Drawing Up the Bobbin Thread ............................................ 31
SECTION III – Basic Sewing
How to Select a Stitch ...........................................................32
Straight Stitch ........................................................................32
Starting to Sew ......................................................................32
Finishing Off a Seam.............................................................32
Cutting the Threads...............................................................33
Changing Sewing Direction...................................................33
Adjusting Needle Position .....................................................33
Adjusting Stitch Length ........................................................ 34
Programming My Personal Settings ................................ 34-35
Sewing on Heavy Fabrics...................................................... 36
Gathering ............................................................................... 36
Zipper Insertion ............................................................... 37-38
Rolled Hem ........................................................................... 39
Zigzag Stitch..........................................................................40
Overcasting............................................................................ 40
Satin Stitch Appliqué .............................................................41
3-Step Zigzag ........................................................................41
Mending a Tear ...................................................................... 42
Serpentine Stitch – Applying Elastic ..................................... 42
Blind Hem Stitches ................................................................ 43
Buttonhole Variations ............................................................ 44
Sensor Buttonholes ......................................................... 45-48
Corded Buttonhole ................................................................ 49
Classic Buttonhole (4 Step Memory) .............................. 50-51
Bound Buttonhole (4 Step Memory) ............................... 52-53
How to Sew on a Button........................................................ 54
Triple Seam............................................................................55
Shell Tuck............................................................................... 55
Stretch Seam.........................................................................55
Super Overlock Stitch............................................................ 56
Super Stretch Stitch .............................................................. 56
Double Overlock Stitch.......................................................... 56
Overcast Stitch ......................................................................57
Arrowtack...............................................................................57
Bartacks.................................................................................58
Darning ..................................................................................59
Eyelets ................................................................................... 60
SECTION IV - Quilting
Piecing Fabrics Together ....................................................... 61
Perfect Start Angle Lines....................................................... 61
Quilt Stitches ......................................................................... 61
Straight Stitch (Dual Feed Foot: AD).....................................62
Quilt Guide............................................................................. 63
Straight Stitch Needle Plate .................................................. 63
Buttonhole Appliqué .............................................................. 64
Patchwork .............................................................................. 65
Free Motion Quilting or Stippling........................................... 65
Stippling Stitch....................................................................... 66
Basting Stitch......................................................................... 66
SECTION V – Heirloom
Pintucks .................................................................................67
Bridging (Fagoting)................................................................67
Hemstitches ...........................................................................68
Fringing ..................................................................................69
Drawn Work ........................................................................... 69
Smocking ............................................................................... 70
SECTION VI – Decorative Sewing
French Knots .........................................................................71
Scallop Edges........................................................................ 71
Corded T rim ........................................................................... 72
Single Cord For Gathering Heavy Fabric..............................72
Twin Needle Sewing ........................................................ 73-74
Satin Stitches – Elongation ................................................... 75
Face to Face .......................................................................... 75
Mirror Image ..........................................................................75
SECTION VII – Programming Combinations
Single Repeat with Memory Auto-Lock................................. 76
Combining a Sequence ......................................................... 77
Inserting a Second Color ................................................ 77-78
Reset Combined Sequence to Beginning............................. 78
Reset Combined Sequence to Beginning of
Incomplete Stitch .............................................................. 78
Combining Letters .................................................................79
How to Preview the Combined Sequence ............................ 80
Editing....................................................................................80
Uniformly Adjusting Stitch Width or Length .......................... 81
Individually Adjusting Stitch Width or Length ........................ 82
Alignment of Stitches within a Sequence ............................. 82
Permanent Memor y
Saving, Overwriting, Recalling and Deleting .............. 83-84
SECTION VIII – Taking Care of Your Machine
Cleaning the Hook Area and Feed Dog................................85
Replacing the Bobbin Case................................................... 86
Changing the Light Bulb........................................................86
Stitch Chart........................................................................... 87
Optional Accessories ............................................................ 88
Warning Messages .......................................................... 89-90
Troubleshooting ..................................................................... 91
NOTE: Information found in this instruction manual is current
at the time of printing. We reserve the right to change and
update specifications and information as needed.
3
SECTION I
Machine Parts and Functions
Part Names
1. Stitch chart brackets (to attach, see page 7)
2. Foot pressure dial
3. Thread take-up lever
4. Thread guide plate
5. Stitch chart
6. LCD screen brightness control
7. Retractable thread guide (pull up)
8. Bobbin winder spindle
9. Bobbin winder stop
10.LCD screen
11.Selection keys (see pages 11–13)
12.Speed control lever
13.Centimeter/inch quick measurements
14.Feed dog lever
15.Knee lifter insert channel
16.Fine adjustment screw
17.Thread tension dial
18.Bobbin cover plate release button
19.Bobbin cover plate
20.Needle plate
21.Built-in needle threader
22.Thread cutter
23.Face plate
24.Auto-thread cut key
25.Up/down needle key
26.Auto-lock key
27.Reverse key
28.Start/stop key
29.Shank
30.Thumbscrew
31.Needle clamp screw
32.Needle
33.Presser foot
34.Buttonhole lever
35. Upper feed mechanism
36.Carrying handle
37.Presser foot lever
38.Spool pins
39.Machine sockets
40.Power switch
41.Flywheel (always turn toward you)
42.Upper thread guide
43.Bobbin winding tension disc
44.Dual feed adjusting dial
45.Thread cutter
w
e
q
r
t
u
i
y
o
!0
!1
!2
!3
!4
!5
!6
!7
!8
!9
@0
@1
@2
@3
@4
@5
@6
@7
@8
@9
#0
#1
#2
#3
#6
#7
#8
#9
$0
$1
$2
$3
#5
#4
$4
$5
4
Standard Accessories
1. A:Standard metal foot (attached to machine)
2. B:Buttonhole foot (4-step)
3. C:Overlock foot
4. D:Hemmer foot
5. E:Zipper foot
6. F: Satin stitch foot
7. F-2:Open toe satin stitch foot
8. G:Blind hem foot
9. H:Multi-cord foot
10. Scant 1/4˝ foot
11. P-2:Open toe embroidery/darning foot
12. R:Automatic buttonhole foot
13. Dual feed foot
14. Quilt guide
15. Dual feed dog
15. Straight stitch needle plate
16. Screwdr iver
17. Screw key
18. Set of needles
19. Lint brush
20. Seam ripper
21. Large spool holders (2)
22. Small spool holders (2)
23. Bobbins (5 total, 1 in machine)
24. Dust cover
25. Quilt table
26. Power supply cord
27. Instruction book
28. Accessory box
29. Foot control
30. Knee lifter
123
456
789
10 11 12
13 14 15
16 17 18
22 23 24
25
26
27
28
29
30
19 20 21
5
Presser Foot and Accessory Definitions
A: Standard Metal Foot
This foot comes attached to your machine. It is
mainly used for straight stitches and zigzag
stitches longer than 1.0. The button locks the foot
in a horizontal position helping to sew over
multiple layered seams.
B: Buttonhole Foot
Sew oversized buttonholes for novelty buttons or a
decorative accent. The two cutout grooves on the
underside of the foot ensure that the buttonhole
sides lie parallel to each other.
C: Overlock Foot
Prevent fabric edges from raveling by finishing the
edge with a zigzag stitch. The brush on the foot
helps the stitch lie flatter and reduces puckering.
Use with medium weight fabrics.
D: Hemmer Foot
Insert the fabric into the spiral on this foot. The
spiral rolls the fabric, creating a rolled hem. An
easy, professional way to sew hems.
E: Zipper Foot
Use when sewing zippers into place. The grooves
on the underside ensure the foot glides over the
zipper coil. Attach either to the left or right of the
needle to sew each side of the zipper.
F: Satin Stitch Foot
The cutout on the underside of the foot is
designed to accommodate dense stitch formation.
Ideal when sewing satin and decorative stitches.
F- 2: Open Toe Satin Stitch Foot
Ideal for precision embroidery, appliqué, cutwork
and monogramming. The cutout on the underside
of the foot accommodates satin stitching and the
open front ensures greater visibility while sewing.
G: Blind Hem Foot
The guide on the foot helps ensure that the needle
catches only one or two fibers of the hem,
resulting in an invisible hemline.
6
H: Multi-Cord Foot
Design your own braids or trims. Place one to
three cords in the foot and sew over cord(s) for a
simple couching method. Or sew over one cord
with a zigzag to gather heavier weight fabrics.
Scant 1/4˝ Foot
Accuracy is the key to successful patchwork/quilt
sewing. Sewn from 3.5 needle position; the edge
of the foot provides a perfect 1/4˝ seam guide. Or
use 4.5 needle position and achieve the desirable
scant 1/4˝ often requested by quilters.
P-2: Open Toe Embroidery/Darning Foot
Skipped stitches are no longer a concern when
sewing free motion embroidery, stippling, dar ning
and monogramming. The spring-loaded foot
moves up and down at the same time as the
needle. Another benefit when using this foot is the
front cutout provides maximum visibility.
R: Automatic Buttonhole Foot
Place button in foot to determine the buttonhole
size. The machine will automatically sew the
corresponding buttonhole.
Quilt Guide
The quilt guide is helpful when sewing parallel,
evenly spaced rows of stitching.
AD:Dual Feed Foot
This is a special foot for hard-to-feed materials.
This foot effectively prevents fabrics from shifting
and puckering. It is great for quilting and matching
plaids.
Straight Stitch Needle Plate
Skipped stitches or puckered fabric? The small
needle entry hole in this plate prevents the needle
from pushing your fabric underneath the needle
plate. (Must use center needle position.)
7
How to Attach Stitch Chart Brackets
Align the screws with the holes on the backside of
the machine. Firmly tighten screws with
screwdriver.
Stitch Chart
The stitch chart can be placed in two positions on
the chart bracket, store or view.
Store Position
The back slots q on the bracket are for store
position e. Slide stitch chart down between the
back slots until the stitch chart rests against
machine bed.
q
w
q
w
View Position
The front slots w on the brackets are for view
position r. Pull up and out the stitch chart from
back slots. Slide stitch chart down between the
front slots.
e
r
Write ‘n Clip Board
Need a handy place for posting information? Flip
over the stitch chart to write messages and then clip
paper or sewing instructions, notes, etc., to board.
NOTES:Do not clip multiple layers of paper or
cardboard. Slide paper under clips; do not
raise clips.
8
Quilt T able
The table provides more sewing surface to support
large fabric pieces to make sewing easier.
Assemble table by attaching six legs to underside
of quilt table with screws.
Attaching Table to Machine
Fit the table around the machine, as shown in the
illustration. If necessary, adjust height of legs to
level table with machine bed by tightening or
loosening leg screws.
Knee Lifter
The knee lifter allows you to raise or lower the
presser foot without using your hands. This is
especially beneficial when pivoting corners or
sewing patchwork pieces.
Insert knee lifter aligning the slots with the
notches.
The presser foot rises equal to the amount of
pressure applied to the knee lifter. Stop sewing
before moving the knee lifter to the right to raise
the presser foot. Release the knee lifter to lower
the presser foot.
CAUTION:
Do not touch the knee lifter while sewing because the
tension discs will open resulting in the upper thread
tension loosening. In addition, the fabric will not feed
properly.
9
Connecting Machine To Power Supply
Before connecting the power cord, make sure the
voltage and frequency shown on the machine are
identical to your electrical power.
To connect machine to power supply, turn off the
power switch q. Insert the foot control plug w
and machine plug e into the machine and the
power supply plug r into the wall socket.
Your machine may come equipped with a
polarized plug (one prong wider than the other). A
polarized plug reduces the risk of electrical
shock. This plug is intended to fit into a polarized
outlet. If the plug does not fit fully into the outlet,
reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do
not modify the plug in any way.
IMPORTANT: When using your sewing machine the
first few times, place waste fabric under the presser
foot and run the machine without thread for a few
minutes. Wipe away excess oil.
NOTE: After turning off the machine, wait 5 seconds
before turning it on again.
For Y our Safety
Do not use extension cords or plug adapters.
Do not touch plug with wet hands.
Always turn off the power/light switch first and then
unplug from the electrical outlet. Examples:
• when leaving the machine unattended
• when cleaning the machine
Always turn off the power/light switch:
• when attaching or removing parts such as
needle, presser foot, needle plate
• when threading needle or bobbin
Do not place anything on the foot control.
Do not place heavy items on cords. Do not subject
cords to heat. Do not use damaged cords. Have
the cord repaired immediately.
While the machine is in operation, always keep
your eye on the sewing area and do not touch any
moving parts such as the thread take-up lever,
flywheel or needle.
q
w
e
r
10
Main Function of Keys
qq
qq
q Start/Stop Key (changes color to indicate
function)
Press this (green) key to start the machine.
The first few stitches will be sewn at a slow speed
and then machine sews at the speed set by the
speed control lever. Press (red) key again to stop
machine. Press and continue to hold key down to
sew at slow speed, release key to sew at set
speed. Press key again to stop.
NOTE: The foot control must be detached to use
this key.
ww
ww
w Reverse Key
If you are sewing 1 (straight stitch), 2 (zigzag stitch) or 3 (3-step zigzag stitch), press and hold this
key. The machine will sew in reverse until you release the key while using the foot control or Start/Stop
key. If the foot control is disconnected, the machine will sew in reverse until you release the key with
or without using the Start/Stop key.
If you are sewing any other stitches, utility or decorative, the machine will immediately stop and sew a
lockstitch when you press this key.
ee
ee
e Auto-Lock Key
Press this key while sewing 1 (straight stitch), 2 (zigzag stitch) or 3 (3-step zigzag stitch) and the
machine will sew a few stitches in place and stop automatically.
Press this key while sewing utility or decorative stitches and the machine will complete the stitch,
lockstitch and stop.
rr
rr
r Up/Down Needle Key
If the needle is up when you press this key, the needle will go down to its lowest position and the LED
signal will turn on. The needle will continue to stop in the down position
If the needle is down when you press this key, the needle will go to its highest position and the LED
signal will turn off. The needle will continue to stop in the up position.
NOTE: The needle will always stop in the up position after auto thread cutting or buttonholes.
tt
tt
t Auto Thread Cut Key
When the machine has stopped sewing, press this key to cut the needle and bobbin threads. (The LED signal
blinks during auto thread cutting.)
CAUTION: Use the thread cutter on the face plate for threads heavier than 30 wt. or decorative
threads.
Clean the auto thread cut mechanism regularly. See page 85.
After auto thread cutting, pull the needle and bobbin threads up and back under the foot.
Auto thread cutting is not recommended when a thread spool is almost empty, as thread will not unwind
smoothly, causing the thread to bunch or slip.
q
w
e
r
t
11
1. LCD Screen Brightness Control
Lighten or darken the screen with this dial.
Keyboard Selection Keys
2. Stitch Width and Needle Position Key
Press “–” or “+” side of key to change setting.
Press “–” or “+” to move needle position left or right.
Straight stitches (1, 6, 011, 012, 061, 062 and 063) can be sewn from
many needle positions by pressing the “–” or “+” side of the key. Center
needle position is 3.5.
3. Stitch Length Key
Press “–” or “+” side of key to change setting. Depending on the stitch
selected, stitch length can be set between 0.0 and 5.0.
NOTE: Fine fabrics should have a stitch length between 1.5 and 2.5,
medium fabrics between 2.0 and 3.0 and heavier fabrics between 3.0 and
4.0.
4. Bobbin Winding Key
Press this key to wind a bobbin. The machine features a separate motor for
bobbin winding making it possible to sew and wind a bobbin at the same
time.
5. Twin Needle Key
Press this key to reduce the width of an individual stitch. The twin needle
symbol is shown on the LCD screen when it is activated. Press the key
again to cancel twin needle function.
6. Elongation Key
Satin stitches 081 to 089 can be lengthened up to five times their regular
size without the stitch length varying. Press this key to change the
elongation. The LCD screen displays the elongated size: X1, X2, X3, X4
or X5.
7. Select Mode Key
When you switch on the machine, the Direct Select Mode is active. You can
select the first ten stitches (illustrated on the keyboard) with a single touch
of the key.
Touch the “MODE” key to activate the 3 Digit Mode. You can select all
stitches by entering the 3 digits for the desired stitch.
Touch “MODE” key again to reactivate the Direct Select Mode.
q
w
e r t y u i o !0
!1 !2 !3 !4 !5 !6 !7
!8
!9
12
8. Memory Save/Recall Key
The 3 Digit Mode has four separate memories for saving a sequence of
stitches. Press this key to activate memory 1 (M1). Press key again to
activate M2. Continue to press this key to access M3, M4 or to exit memory.
Once a memory is activated, press the “ENTER” key to save the sequence.
To recall a saved memory, press “M” key until desired memory appears.
To activate the saved sequence, press “Mirror Image” key.
9. Enter Key
Press this key after selecting a stitch in the 3 Digit Mode and that stitch will
be memorized. Up to 50 stitches can be combined together.
These stitches cannot be memorized into a sequence: 010, 011, 071 – 076,
078 and 079.
10. Memory Auto-Lock Key
After combining a sequence of stitches in the 3 Digit Mode press this key to
add a locking stitch at the end.
Begin sewing; at the end of the sequence the machine will automatically
lock the last stitch and stop.
• symbol will appear in LCD screen.
11. Face to Face Key
When this key is pressed after selecting a stitch, the stitch will be flipped
vertically (as it appears on the stitch chart) and a symbol will appear in the
LCD screen.
Stitches that are compatible with this key are identified on the stitch chart
with an “F” directly following the stitch number.
12. Mirror Image Key
When this key is pressed after selecting a stitch, the stitch will be flipped
horizontally (as it appears on the stitch chart) and a symbol will appear in
the LCD screen.
If you have activated the permanent memories (M1, M2, M3, M4), press
this key to recall the saved sequence.
13. My Personal Setting Key
Select a stitch in Direct Select Mode or 3 Digit Mode and override the
factory settings by changing width/needle position, length, face to face,
mirror image or elongation. Press this key after changing settings. Press
“ENTER” key. New settings will now be saved as the default settings with
PS symbol on LCD screen.
14. Clear Key
When this key is pressed, the last memorized stitch or the stitch that is
above the cursor will be cleared. Press and hold the “C” key; the entire
sequence is cleared. If this key is pressed after sewing a sequence, the
sequence will be deleted.
15. Review Memory Left Key
Use this key to review stitches in a memorized sequence when all stitches
do not appear on the screen.
OR
Press this key to move the cursor left until it is under the stitch that will be
edited.
13
18. Stitch Selection Keys
You can select a stitch in the Direct Select Mode
by pressing the key that is illustrated with the
desired stitch.
To select stitches in the 3 Digit Mode, simply
press the three digits for the desired stitch. To
cancel the stitch you selected, press the “C” key or
select a different stitch.
16. Review Memory Right Key
Use this key to review stitches in a memorized sequence when all stitches do
not appear on the screen.
OR
Press this key to move the cursor right until it is under the stitch that will be
edited.
17. Memory Auto Thread Cut Key
Press this key after selecting a stitch and when the Auto-Lock key is pressed
the machine will automatically cut threads after lockstitching is completed.
Press this key after the last stitch in a sequence and when the sequence
finishes sewing, the machine will automatically cut the threads.
NOTE:After this key is pressed, the Auto Thread Cut Key LED signal turns on.
19. Symbols on the LCD Screen
q Selected stitch. (The number 1 to the right of
the stitch illustration means only one stitch will
be sewn if used in a sequence.)
w Recommended range for setting needle thread
tension dial.
e Elna recommends using this presser foot for
best sewing results.
r Stitch width or needle position – computer
automatically sets width or needle position after
a stitch is selected.
t Stitch length – computer automatically sets
length after a stitch is selected.
y Quick Resumption Mode. Switch off the
machine. The last stitch(es) that were sewn will
appear when machine is switched on.
See page 14.
u Twin or single needle. See page 11.
i Sound Mode. Machine beeps after touching
any key. See page 14.
Other symbols that can appear:
a. My Personal Settings are applied to this
stitch.
b. Face to Face is active for this stitch.
c. Mirror Image is active for this stitch.
d. Face to Face and Mirror Image are active
for this stitch.
e. Elongation is available for this stitch.
q
w e r t
y
u
i
a.
b.
c.
d.
e.
14
Setting Quick Resumption, Sound and
Language Modes
These three modes/functions can be set according
to your preferences. Each new setting requires
you to turn OFF the power switch. Turn ON the
power switch while pressing “ENTER” key.
Message screen appears. Press “1” key to change
quick resumption or “2” key to change sound or “3”
key to change language.
Quick Resumption – The last stitch or
memorized sequence of stitches that were sewn
will appear when machine is switched on.
z Press “1” key.
x Press “1” or “2” key to change setting between
Normal Set and Resumption Set.
c Press “ENTER” key.
Sound – Turn off the beep sound (warning beep
sounds will not be turned off) or change the beep
volume.
z Press “2” key.
x Press “1”, “2”, “3”, or “4” key to change among
settings.
c Press “ENTER” key.
Language – Choose one of the 10 languages:
English, Spanish, French, Danish, German, Italian,
Dutch, Russian, Slovenian, or Swedish.
z Press “3” key.
x Press “Review Memory Right” key or “Review
Memory Left” key to change among languages.
c Press “ENTER” key.
~
~
z
x
c
z
x
c
z
x
c
15
Reset to Factory Default
It is possible to reset the machine to the factory
defaults with English language as default.
Turn OFF the power switch. Press “ENTER” key
while turning power switch ON. Message screen
appears.
Press “0” key. Message screen appears.
Press “ENTER” key to confirm and reset to factory
default.
OR
Turn off power switch to cancel the reset.
Controlling Sewing Speed
Sewing speed can be varied with the foot control.
The harder you press on the foot control, the
faster the machine runs.
The maximum sewing speed can be varied by
sliding the speed control lever. For a faster speed,
slide it to the right; for a slower speed, slide it to
the left.
Foot Pressure Dial
Change the pressure on the presser foot by rotating
the foot pressure dial q to move the indicator w.
Set the pressure at “3” for regular sewing.
Reduce the pressure to “2” for appliqué, cutwork,
drawn work, basting and embroidery.
Velours and knits with a lot of stretch may require a
“1” setting.
NOTE: Never reduce the pressure below “0”.
q
w
16
How To Drop the Feed Dog
The feed dog can be dropped out of position for
special sewing techniques: free motion embroidery,
stippling, button sewing, etc.
The feed dog must always be up for regular sewing.
The machine will run with the feed dog down if the
following stitches are selected: 1, 2, 3, 4, 011, 014,
015, 016, 017, 042, 061 and 062. The machine will not
sew with the feed dog down if any other stitches are
selected.
NOTE: The foot displayed on the LCD screen
changes to the open toe embroidery/darning foot
when the feed dog is down, except after selecting
stitch 2.
Locate the feed dog lever on the front right side of
the machine. Slide the lever either to the right
(down) q or to the left (up) w. To bring up the feed
dog, hand turn the flywheel after sliding lever to the
left.
If the feed dog is down, a message illustration will
appear in the LCD screen when sewing begins.
Presser Foot Lever
Raise and lower the foot with this lever q.
Before sewing can occur the presser foot must be
lowered to close the tension discs. If you attempt to
sew with the foot in the up position, the LCD screen
will show this message illustration to remind you to
lower the foot.
q
w
q
q
Additional Presser Foot Clearance
You can raise the presser foot about 6.5 mm (1/4˝)
higher than the normal up position for easy removal
of the presser foot or to place heavy fabrics under
the presser foot or setting the dual feed device. Pull
the presser foot lever q up beyond the normal up
position.
17
Attaching and Removing Presser Feet
Press the “Up/Down Needle” key until the needle
is in the raised position.
Turn OFF the power switch. Raise the presser foot
and press the red button q on back of the shank.
The presser foot will drop off.
Place the selected presser foot so the pin e on
the foot lies just under the groove w of the shank.
Lower the presser bar and attach the foot.
Attaching and Removing Shank
Turn OFF the power switch. Raise the presser
bar.
Turn the thumbscrew q counterclockwise with the
screwdriver to remove the shank.
To attach, loosen the thumbscrew q counterclockwise
with the screwdriver. Attach the presser foot w to the
presser bar e. Tighten the thumbscrew by turning it
clockwise.
q
w
e
q
w
e
18
q
r
t
w
q
Loosen the thumbscrew w and remove the foot holder
e.
Attach the Dual feed foot r to the pressure bar t, and
tighten thumbscrew lightly. Lower the presser foot lifter
and tighten the thumbscrew securely.
To attach the Dual feed foot:
To engage the dual feed device
When you use the Dual feed, attach the Dual feed as
follows.
The attaching and detaching Dual feed procedures will
be reviewed in LCD screen accordingly as you press
the key when stitch 1 is selected.
Press the key to exit the reviewing Dual feed
procedure.
Setting for Dual Feed Sewing
Raise the needle and presser foot q.
Raise the presser foot lifter to its extra lift position q.
Lower the Dual feed device w slowly and swing
forward to the under side of the Dual feed foot until
they engage.
w
e
19
w
q
r
y
u
r
To disengage the Dual Feed Device
Pull down the Dual feed device w and swing it to
the rear to disengage. Push up the Dual feed
device until the notch of the Dual feed device
catches the pin e.
Detaching the Dual Feed Foot
Raise the needle and the presser foot lifter q
to its extra lift position.
Loosen the thumb screw r and remove the Dual feed
foot t.
Attach the presser foot holder y to the presser
bar u.
Tighten the thumbscrew by turning it clockwise
lightly.
Lower the presser bar.
Depress the foot against the needle plate, and
loosen the thumbscrew slightly.
Tighten the thumbscrew firmly.
t
Set the presser foot lifter to normal position.
z
x
z
x
z
x
c
z
x
c
e
q
20
Seam Allowance Lines
The lines on the needle plate and bobbin cover plate
help you measure seam width.
The numbers indicate the distance (in millimeters
and inches) between the center needle position 3.5
q and the seam allowance line w. Use the seam
allowance line as a guide for the fabric edge e.
Centimeter/Inch Quick Measurements
Use this handy tool located on the machine base
for quick measurements.
q
e
w
21
Adjusting the Needle Thread Tension
Choosing the Correct Tension - Straight Stitch
The ideal straight stitch will have threads locked
between the two layers of fabric.
According to the LCD screen, needle thread tension
can range from 2 – 6 q and is normally set on 4.
Align the number 4 on the tension dial with the
setting mark w.
If you look at the needle thread e (top thread) and
bobbin thread r (bottom thread), you will notice
that there are no gaps. Each stitch is smooth and
even.
Occasionally the needle thread tension needs to be
adjusted. Examples:
— stiff or heavy fabric
— sewing more than two layers of fabric
— type of stitch
— thread
When adjusting needle thread tension, the higher
numbers tighten, the lower numbers loosen.
q
w
e
r
• Tension is too tight
The bobbin thread shows through on the topside of
the fabric and it will feel bumpy.
Turn the dial to a lower number to loosen the needle
thread tension.
•Tension is too loose
The needle thread shows through on the underside
of the fabric and it will feel bumpy.
Turn the dial to a higher number to tighten the
needle thread tension.
• Adjusting Tension for Zigzag and Satin Stitches
The upper thread tension should be slightly looser
when sewing a zigzag or a satin stitch. The upper
thread should appear slightly on the underside of
the fabric.
22
Using the Fine Adjustment Screw
Choice of fabrics and threads may affect the stitch
formation when sewing decorative stitches, letters
and numbers or classic 4 step memory buttonhole
(071). The fine adjustment screw can be used to
either lengthen or shorten the stitch.
q Fine adjustment screw
w Standard mark
e Setting mark
To fine tune, use a screwdriver to move the setting
mark.
w
q
e
rt
y
u
(+) (–)
(+) (–)
• If stitches are too short r, correct by turning the
screw in the direction of “+”.
• If stitches are too long t, correct by turning the
screw in the direction of “–”.
• If letters are overlapped y, correct by turning the
screw in the direction of “+”.
• If letters are too spread out u, correct by turning the
screw in the direction of “–”.
071 Classic 4 Step Memory Buttonhole
(Applies only to this style.)
Always mak e the adjustment according to the left side.
When adjustment screw is turned, it changes both
sides of the buttonhole.
• If left side of buttonhole is less dense (too open) i
compared to right side, corrected by turning screw in
direction of “+”.
• If left side of buttonhole is more dense (too closed)
o compared to right side, corrected by turning
screw in direction of “–”.
NOTE: After making an y fine tuning adjustment press
“Enter” key or reselect buttonhole to reset machine.
(+) (–)
io
23
SECTION II
Getting Ready to Sew
Selecting the Correct Needle for Fabrics
There are many kinds of fabrics, threads and
needles. It is important to use the correct ones
together.
Always purchase good quality thread. It should be
strong, smooth and even in thickness. Use the
same thread for needle and bobbin. Always test
thread and needle size on a scrap piece of fabric.
In general, fine threads (the larger the number, the
finer the thread) and needles (the smaller the
number, the finer the needle) are used for sewing
lightweight fabrics and heavier threads and larger
needles are used for sewing heavyweight fabrics.
There are many specialty needles available from
your sewing machine dealer.
Check your needles frequently for rough or blunt
tips. Snags and runs in knits, fine silks and silklike
fabrics are permanent and are often caused
by damaged needles.
NOTE: A universal needle size 14/90 comes
inserted in your machine
Weight
Fabric Needle T ype
Needle
Size
Very Chiffon, Fine Lace, Universal 9 (65)
Light Organdy Ball Point 9 (65)
Light
Batiste, Lawn, Crepe
Stretch 11 (75)
de Chine, Challis,
Handkerchief Linen,
Crepe, Taffeta, Satin
Universal 11 (75)
12 (80)
Single Knits, Jersey, Stretch 11 (75)
Swimwear, Tricot Ball Point 11 (75)
Leather, Suede Leather 11(75)
Medium
Flannel, V elour , Velvet,
Universal 14 (90)
Velveteen, Corduroy,
Linen, Gabardine,
Wool, Terry, Burlap
Double Knits, Stretch
Ball Point 14 (90)
Velour, Stretch Terry,
Sweater Knits
Leather, Vinyl, Suede
Leather 14 (90)
Heavy
Denim, Sailcloth,
Denim 16 (100)
Ticking
Coating, Polar Fleece,
Universal 16 (100)
Drapery, and
Upholstery Fabrics
Leather, Suede
Leather 16 (100)
Very
Canvas, Duck,
Universal 18 (110)
Heavy
Upholstery Fabrics
Topstitching for
Topstitching 11 (75)
Special Finish
14 (90)
zx
c
q
w
Changing Needles
z Turn ON the power switch. Press the “Up/Down
Needle” key to raise the needle. Lower the presser
foot. Turn OFF the power switch.
Turn the needle clamp screw q counterclockwise
to loosen. Remove the needle from the clamp.
x Insert the new needle into needle clamp with the
flat side to the back, pushing it up as far as it will go
w. Tighten the clamp screw firmly.
c To determine if the needle is defective, place the
flat side of the needle on something flat (a needle
plate, piece of glass, etc.). The gap between the
needle and the flat surface should be consistent.
Never use a bent or blunt needle, as it may cause
skipped stitches or thread breakage. Defective
needles can ruin the fabric. Always purchase good
quality needles. Change needles often.
24
Needle Definitions
The illustration identifies the main parts of a
sewing machine needle.
q Body
w Shaft
e Long groove (round side of needle)
r Short groove (flat side of needle)
t Eye
y Point
q
w
e
r
t
y
A
B
C
D
E
F
G
A: Universal – an all-purpose needle that handles
most woven and knit fabrics.
B: Ball point – the point spreads the fibers,
preventing tears and is especially suited for loose
knits and interlock knits. Not recommended for
embroidery.
C: Denim – the sharp point effectively pierces
densely woven fabrics such as denim and canvas.
D: Stretch – specially designed to prevent skipped
stitches in synthetic suedes and elasticized knits
(swimwear).
E: Leather – the cutting point creates small holes in
leather and suede. Holes remain after stitching is
removed.
F: T opstitching – the extra sharp point penetrates
layers of fabrics; extra large eye and large groove
accommodate heavyweight topstitching thread.
G: T win/Double – 2 needles are joined on a crossbar
and share a single shaft. Sews two parallel rows
of stitching. Available in universal and ballpoint.
25
Winding a Bobbin
To remove bobbin, slide bobbin cover plate release
button q to the right and lift away the bobbin cover
plate w.
q
w
e
r
y
u
t
y
io
Lift out the bobbin e.
Turn ON the power switch.
Always use bobbin type supplied with machine.
Pull up the retractable thread guide r.
Place the spool of thread t on the right side spool
pin y with the thread coming off the spool as shown.
Attach the spool holder u and press it firmly against
the spool of thread.
NOTE: Spool holder needs to be changed according
to the type of thread spool.
i Large spool
o Small spool
Avoid using a spool if it is almost empty, as thread may
tangle.
26
Pull the thread up and through the right retractable
thread guide q from behind.
Pull the thread under and around the bobbin winding
tension disc w.
Pass the thread through the hole in the bobbin e
from inside to the outside. Place the bobbin on the
bobbin winder spindle r.
Push bobbin winder stop t to the left.
Holding the free end of the thread, press the
“Bobbin Winding” key y. (A separate motor winds
the bobbin, allowing you to sew at the same time
bobbin winding occurs.)
Press the “Bobbin Winding” key to STOP bobbin
winding after the bobbin has made a few turns. Cut
the thread tail close to the hole in the bobbin.
Press the “Bobbin Winding” key again. When the
bobbin is fully wound, bobbin winding is stopped
and bobbin winder stop will automatically move
right. If you do not wind a full bobbin, stop bobbin
winding and return bobbin winder stop to the right.
Cut thread.
q
w
e
r
t
y
27
Inserting the Bobbin
Place the bobbin in the bobbin case with the
thread running counterclockwise.
q
Guide the thread into notch q on the front side of
the bobbin case.
Hold the bobbin with your right hand and pull the
thread to the left, through the tension spring
blades w.
Continue pulling the thread lightly until the thread
slips into notch e.
Pull out about 15 cm (6˝) of thread.
Replace the bobbin cover plate.
Refer to the chart shown on the bobbin cover
plate to check the threading.
w
e
28
Threading the Machine
Raise the presser foot. Press the “Up/down Needle”
key until the needle is in an up position.
Place the spool of thread on the left spool pin with
the thread coming off the spool as shown and
attach the spool holder.
Pull the thread up and through the left retractable
thread guide q from behind.
Pull the thread under the upper thread guide w.
e
r
e
q
w
r
Using both hands, firmly insert the thread under the
thread guide plate e.
Pull thread forward under the left thread guide r.
Loading...