INSTALLATION / OWNER’S MANUAL
Avado - Pull-Out Bar Faucet
LKAV3042CR
LKAV3042NK
LKLFAV3042CR
LKLFAV3042NK
Includes:
D1
D 
D2
D3
E |
B |
C2
C
C1
F
B1
B2
B3 A
B4
NOTE: these washers are not used on this faucet model
Tools:
1/2” |
5/8” |
13/16” |
[13 mm] |
[16 mm] |
[20 mm] |
SAVE FOR CONSUMER
WARNING: please carefully read and properly follow the instructions for installation found in this manual.
STEPS:
1
A
Before inserting the single lever group in the hole of the sink, make sure that the base gasket is properly positioned in its seat and that the flexible hoses are well tightened to the body of the tap.
Place the single lever group in the hole of the sink, orienting the spout toward the sink tank.
2
B1
B3 
B2 B4 
E
For countertop thicknesses less than 1/16” thick use the rubber gasket (B1) and mounting flange
(B2), for all other installations use the rubber gasket (B1) and metal washer (B3).
Secure mounting hardware in place by tightening mounting nut (B4) with wrench (E).
3
C2 
13/16” |
C1 |
[20 mm] |
D1 
1/2” [13 mm]
Install the check valve (C1) to the outlet hose with a rubber washer (C2).
Secure with wrench.
Attach the pull-down hose to the bottom of the check valve with a rubber washer (D1).
Secure with wrench.
4 |
5 |
6 |
|
|
D3 |
D2
Attach the counterweight (D2) to the flexible hose approximately 15-3/4” [400mm] from the connection to the outlet pipe.
F
Tighten the shower (F) to the hose interposing the gasket (D3) and confirm the hose can slide smoothly through the passage hole.
Blue
5/8” |
Red |
[16 mm] |
|
Cold
Hot
Connecttheflexiblehosestothesupplyconnections with rubber gaskets.
Secure with wrench.
Turn on the water and check for leaks.
CARTRIDGE REPLACEMENT
1 |
2 |
3 |
|
|
|
13/16” |
|
|
|
[21 mm] |
|
C |
F |
E |
|
D |
||
|
|
|
|
B |
A |
|
X |
|
|
||
1/8” |
|
|
|
[2,5 mm] |
|
|
|
Before dissassembling the faucet be sure that the water supply is turned off.
Remove the finish cap (A), paying attention not to damage it. Remove the setscrew (B) with a 1/8” [2,5mm] hex wrench. Remove the handle (C). Lift the finishing ring nut (D) using the reference notch. Unscrew the cartridge nut (E) then pull out the cartridge (F). Put the new cartridge into the body of the faucet, checking that the two centering pins enter into the respective seats (X) and that the gaskets on the cartridge are well positioned.
Reassmble the handle following the instructions in reverse order.
AERATOR CLEANING / REPLACING
1 |
2 |
Before removing the aerator make sure that the faucet is turned off.
If the supply is not fluid unscrew manually the aerator-holder, remove the filter without damaging and/or loosing the gasket.
If the aerator is clogged just rinse it with running water. Do not use detergents.
Reassemble the aerator by following the instructions in reverse order.
Loading...