Eaton Transmission TRIG0910 User Manual

Installation Guide

Eaton Automated Transmission
Engine Configuration Settings Guide

TRIG0910 EN-US

September 2015

Table of Contents

Automated Transmission Engine

Configuration Settings . . . . . . . . . . . . . . . . . . 1

Caterpillar

AutoShift Medium-Duty / Heavy-Duty . . . . . . . . 1

UltraShift ASW . . . . . . . . . . . . . . . . . . . . . . . . . 1

UltraShift Medium-Duty DM . . . . . . . . . . . . . . . 2

UltraShift Heavy-Duty DM . . . . . . . . . . . . . . . . 3

UltraShift PLUS Heavy-Duty . . . . . . . . . . . . . . . 3

Cummins

AutoShift Medium-Duty / Heavy-Duty . . . . . . . . 4

UltraShift ASW . . . . . . . . . . . . . . . . . . . . . . . . . 5

UltraShift Medium-Duty DM . . . . . . . . . . . . . . . 5

UltraShift Heavy-Duty DM . . . . . . . . . . . . . . . . . 6

Procision. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Medium-Duty Hybrid. . . . . . . . . . . . . . . . . . . . . 8

UltraShift PLUS Heavy-Duty . . . . . . . . . . . . . . . 9

Hino

Ultrashift Medium Duty DM. . . . . . . . . . . . . . . . 11

International

EPA 2007 Emission Engine HT-570

AutoShift Heavy-Duty. . . . . . . . . . . . . . . . . . 11

EPA 2007 Emission Engine Maxx Force DT (DT-466)

UltraShift ASW . . . . . . . . . . . . . . . . . . . . . . . 11

UltraShift Medium-Duty DM. . . . . . . . . . . . . 11

EPA 2010 Emission Engine MaxxForce DT (DT-466)

UltraShift Medium-Duty DM. . . . . . . . . . . . . 12

Hybrid (HEV) . . . . . . . . . . . . . . . . . . . . . . . 12

EPA 2007 Emission Engines MaxxForce 11 and 13

UltraShift Heavy-Duty DM . . . . . . . . . . . . . . 13

UltraShift PLUS Heavy-Duty. . . . . . . . . . . . . 13

EPA 2010 Emission Engines MaxxForce 11 and 13

UltraShift Heavy-Duty DM . . . . . . . . . . . . . . 14

UltraShift PLUS Heavy-Duty. . . . . . . . . . . . . 14

International MaxxForce

Hybrid (HEV) . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Detroit Diesel
Pre 2007

AutoShift Heavy-Duty . . . . . . . . . . . . . . . . . . 17

UltraShift Heavy-Duty DM . . . . . . . . . . . . . . . 17

EPA 2010 Emission Engines DD13, DD15, DD16

AutoShift - Heavy-Duty . . . . . . . . . . . . . . . . . 18

UltraShift - Heavy-Duty DM. . . . . . . . . . . . . . 19

UltraShift PLUS Heavy-Duty . . . . . . . . . . . . . 20

Detroit Diesel/Mercedes

EPA 2007 Emission Engines

AutoShift - Heavy-Duty . . . . . . . . . . . . . . . . . 19

UltraShift - Heavy-Duty DM. . . . . . . . . . . . . . 21

UltraShift PLUS Heavy-Duty . . . . . . . . . . . . . 22

Mercedes

Pre 2007

AutoShift Medium-Duty. . . . . . . . . . . . . . . . . 23

AutoShift Heavy-Duty . . . . . . . . . . . . . . . . . . 24

UltraShift ASW . . . . . . . . . . . . . . . . . . . . . . . 24

UltraShift Medium-Duty DM . . . . . . . . . . . . . 25

UltraShift Heavy-Duty . . . . . . . . . . . . . . . . . . 26

PACCAR MX 12.9L Engine

Configuration Settings . . . . . . . . . . . . . . . . . . .27

Volvo/Mack Engine Configuration

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Volvo/Mack Body Builder Module

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Change Control Log . . . . . . . . . . . . . . . . . . . . .28

Table of Contents

i

Engine Configuration

Automated Transmission Engine Configuration Settings

These engine configurations are for the following Fuller® Automated Transmissions.

• AutoShift / UltraShift Gen 2 and Gen 3

Caterpillar

AutoShift Medium-Duty / Heavy-Duty

Programmable Parameter Table Required Setting

Engine Gear Parameters (Note: Gear RPM Limits disabled in Drive.)

Transmission Style

Governor Type Min/Max

Top Gear Ratio 0.780 for 6A, 0.740 for 10B, 0.730 for 10C,

Top Gear Minus one ratio 1.00 for 6A, 1.00 for 10B & 10C, 0.860 for 18A

Top Gear Minus two ratio 1.59 for 6A, 1.36 for 10B, 1.38 for 10C, 1.00 for 18A

Data Link Parameters

Powertrain Data Link J1939

Input Selections (2007 and Later Engines) Recommended

Transmission Neutral Switch J1939

Manual Option 1 (2006 and Earlier Engines)

Manual (2007 and Later Engines)

0.730 for 18A

UltraShift ASW

Programmable Parameter Table Required Setting

Engine Gear Parameters (Note: Gear RPM Limits disabled in Drive.)

Transmission Style

Governor Type Min/Max

Top Gear Ratio 0.780 for 6A

1

Automatic Option 1 (2006 and Earlier Engines)

Automatic (2007 and Later Engines)

Engine Configuration

Programmable Parameter Table Required Setting

Top Gear Minus one ratio 1.00 for 6A

Top Gear Minus two ratio 1.59 for 6A

Data Link Parameters

Powertrain Data Link J1939

Input Selections (2007 and Later Engines)

Transmission Neutral Switch J1939

UltraShift Medium-Duty DM

Programmable Parameter Table Required Setting

Engine Gear Parameters (Note: Gear RPM Limits disabled in Drive.)

Transmission Style

Governor Type Min/Max

Top Gear Ratio 0.780 for 6A HV OD, 1.00 for 5A HV DIR

Top Gear Minus one ratio 1.00 for 6A HV OD, 1.59 for 5A HV DIR

Configuration

Engine

Automatic Option 1 (2006 and Earlier Engines)

Automatic (2007 and Later Engines)

Top Gear Minus two ratio 1.59 for 6A HV OD, 2.52 for 5A HV DIR

Low Idle Engine RPM 700 rpm max

Data Link Parameters

Powertrain Data Link J1939

Input Selections (2007 and Later Engines)

Transmission Neutral Switch J1939

2

UltraShift Heavy-Duty DM

Programmable Parameter Table Required Setting

Engine Gear Parameters (Note: Gear RPM Limits disabled in Drive.)

Transmission Style

Governor Type Min/Max

Top Gear Ratio 0.740 for 10B LST OD, 1.00 for 10B LST DIR,

Top Gear Minus one ratio 1.00 for 10B LST OD, 1.34 for 10B LST DIR,

Top Gear Minus two ratio 1.36 for 10B LST OD, 1.83 for 10B LST DIR,

Low Idle Engine RPM 625 rpm max (Until further notification)

Engine Configuration

Automatic Option 1 (2006 and Earlier Engines)

Automatic (2007 and Later Engines)

0.730 for 13 LHP & LEP

0.860 for 13 LHP & LEP

1.00 for 13 LHP & LEP

Data Link Parameters

Powertrain Data Link J1939

Input Selections (2007 and Later Engines)

Transmission Neutral Switch J1939

UltraShift PLUS Heavy-Duty

Programmable Parameter Table Required Setting

Engine Gear Parameters (Note: Gear RPM Limits disabled in Drive.)

Transmission Style Automatic (2007 and Later Engines)

Governor Type Min/Max

Top Gear Ratio 0.74 for 8LL VCS

0.73 for 9ALL VMS

1.00 for 10B LAS DD

0.73 for 10C LAS OD

0.73 for 13A MHP

0.73 for 18B MXP

0.73 for 18B VXP

3

Engine Configuration

Programmable Parameter Table Required Setting

Top Gear Minus one ratio 1.00 for 8LL VCS

1.00 for 9ALL VMS

1.35 for 10B LAS DD

1.00 for 10C LAS OD

0.86 for 13A MHP

0.86 for 18B MXP

0.86 for 18B VXP

Top Gear Minus two ratio 1.36 for 8LL VCS

1.38 for 9ALL VMS

1.83 for 10B LAS DD

1.38 for 10C LAS OD

1.00 for 13A MHP

1.00 for 18B MXP

1.00 for 18B VXP

Configuration

Engine

Data Link Parameters

Powertrain Data Link J1939

Cummins

AutoShift Medium-Duty / Heavy-Duty

Features and Parameters Required Setting

Accelerator (or Governor) Type

Accelerator (or Governor) Type Automotive

Adjustable Low Idle Speed

Low Idle Speed

Low Idle Speed Adjustment Switch

Transmission Setup

Clutch Pedal Position Switch Installed

Transmission Type Fully Automated with Clutch Pedal (or Fully Automated if

clutch pedal distinction not present)

Gear down transmission ratio 1.00 for 6A, 1.00 for 10B & 10C, 0.860 for 18A

Top Gear Transmission ratio 0.780 for 6A, 0.740 for 10B, 0.730 for 10C,

0.730 for 18A

4

Engine Configuration

Features and Parameters Required Setting

Switched Maximum Engine Operating Speed

Maximum Switched Engine Speed Highest allowable rpm (min of high idle) Or Disable

PTO/Remote PTO Recommended

Service Brake Override in PTO Enable

Clutch Override in PTO Enable

UltraShift ASW

Features and Parameters Required Setting

Accelerator (or Governor) Type

Accelerator (or Governor) Type Automotive

Transmission Setup

Clutch Pedal Position Switch Not Installed

Transmission Type Fully Automated without Clutch Pedal

Gear down transmission ratio 1.00 for 6A

Top Gear Transmission ratio 0.78 for 6A

Switched Maximum Engine Operating Speed

Maximum Switched Engine Speed Highest allowable rpm (min of high idle) Or Disable

UltraShift Medium-Duty DM

Features and Parameters Required Setting

Accelerator (or Governor) Type

Accelerator (or Governor) Type Automotive

Remote Accelerator Disable

5

Engine Configuration

Features and Parameters Required Setting

Adjustable Low Idle Speed

Low Idle Speed 700 rpm max

Low Idle Speed Adjustment Switch Disable

Transmission Setup

Clutch Pedal Position Switch Not Installed

Transmission Type Fully Automated without Clutch Pedal

Gear down transmission ratio 1.00 for 6A HV OD, 1.59 for 5A HV DIR

Top Gear Transmission ratio 0.780 for 6A HV OD, 1.00 for 5A HV DIR

Switched Maximum Engine Operating Speed

Maximum Switched Engine Speed Highest allowable rpm (min of high idle) Or Disable

If PTO/Remote PTO is Enabled Required

PTO/Remote PTO

Service Brake Override in PTO Enable

Configuration

Engine

PTO/Remote PTO

PTO Resume Switch Speed 1000 rpm minimum

Clutch Override in PTO Disable

UltraShift Heavy-Duty DM

Features and Parameters Required Setting

Accelerator (or Governor) Type

Accelerator (or Governor) Type Automotive

Adjustable Low Idle Speed

Recommended

6

Engine Configuration

Features and Parameters Required Setting

Low Idle Speed 625 rpm max (2009 and earlier engines)

700 rpm max (2010 and later engines)

Low Idle Speed Adjustment Switch Disable

Transmission Setup

Clutch Pedal Position Switch Not Installed

Transmission Type Fully Automated without Clutch Pedal

Gear down transmission ratio 1.00 for 10B LST OD, 1.34 for 10B LST DIR,

0.860 for 13 LHP & LEP

Top Gear Transmission ratio 0.740 for 10B LST OD, 1.00 for 10B LST DIR,

0.730 for 13 LHP & LEP

Switched Maximum Engine Operating Speed

Maximum Switched Engine Speed Highest allowable rpm (min of high idle) Or Disable

If PTO/Remote PTO is Enabled Required

PTO/Remote PTO

Service Brake Override in PTO Enable

PTO/Remote PTO

PTO Resume Switch Speed 1000 rpm minimum

Clutch Override in PTO Disable

Procision

Features and Parameters Required Setting

Recommended

Transmission Setup

Transmission Type Duel Clutch Transmission (DCT)

Gear Down Transmission Ratio 0.76

Top Gear Ratio 0.64

7

Engine Configuration

Features and Parameters Required Setting

Aftertreatment Enable

Diesel Particulate Filter Regeneration Allowed in PTO
and Other Modes

Fan Control

Fan on with Engine Braking Disable

Fast Idle Warmup

Fast Idle Warmup Enable

Fast Idle Warmup Idle Speed 1250 RPM

Adjustable Low Idle Speed

Low Idle Speed 750 RPM

Variable Rate Vehicle Acceleration Management Disable

Disable

Recommended Setting

Configuration

Engine

Medium-Duty Hybrid

Features and Parameters Required Setting

Accelerator Options

Remote Accelerator Pedal or Lever Disable, unless Approved by Eaton Application

Governor Type

Governor Type Automotive

Transmission Setup Enable

Transmission Type Fully Automated without Clutch Pedal

Gear Down Transmission Ratio 1.00 for 6A OD

Top Gear Transmission ratio 0.780 for 6A OD

Engineering

8

Engine Configuration

Features and Parameters Required Setting

Clutch Pedal Position Switch Not Installed

Switched Maximum Engine Operating Speed

Maximum Switched Engine Speed Disable

SAE J1939 Multiplexing

Auxiliary Shutdown Switch Enable

-Source Address 239

Clutch Pedal Position Switch Disable

If PTO is Enabled

Clutch Override Disable

Remote PTO Disable

Service Brake Override Enable

UltraShift PLUS Heavy-Duty

Features and Parameters Required Setting

Governor Type

Governor Type Automotive

Powertrain Protection Disable

Transmission Setup

Clutch Pedal Position Switch Not Installed

Transmission Type Fully Automated without Clutch Pedal

Gear Down Transmission Ratio 1.00 for 8LL VCS

1.00 for 9ALL VMS

1.35 for 10B LAS DD

1.00 for 10C LAS OD

0.86 for 13A MHP

0.86 for 18B MXP

0.86 for 18B VXP

9

Engine Configuration

Features and Parameters Required Setting

Top Gear Transmission Ratio 0.74 for 8LL VCS

0.73 for 9ALL VMS

1.00 for 10B LAS DD

0.73 for 10C LAS OD

0.73 for 13A MHP

0.73 for 18B MXP

0.73 for 18B VXP

Switched Maximum Engine Operating Speed Disable

If PTO/Remote PTO is Enabled

Service Brake Override Enable

Clutch Override Disable

Configuration

Engine

Vehicle Speed Anti-Tampering (If Enabled)
8LL VCS and 9ALL VMS ONLY

Tampering Sensitivity Level Low

SmartCoast Enable, if customer has purchased feature from

Cummins

10

Engine Configuration

Hino

Ultrashift Medium Duty DM

Please work with an authorized Hino dealer to verify engine configuration.

International (EPA 2007 Emission Engine HT-570)

AutoShift Heavy-Duty

Programmable Parameter Table Required Setting

Engine Parameters

Transmission Type Manual

Engine Family Rating Code 6122-330/1150

International (EPA 2007 Emission Engine MaxxForce DT (DT-466))

UltraShift ASW

Programmable Parameter Table Required Setting

Engine Parameters

Transmission Type Allison-MD

Engine Family Rating Code 2141-255/660

2131-245/620

2132-245/660

UltraShift Medium-Duty DM

Programmable Parameter Table Required Setting

11

Engine Gear Parameters

Transmission Type Allison-MD

Engine Family Rating Code 1121-210/520

1141-225/560

Engine Configuration

Programmable Parameter Table Required Setting

1122-225/620

2141-255/660

2131-245/620

2132-245/660

International (EPA 2010 Emission Engine MaxxForce DT (DT-466))

UltraShift Medium-Duty DM

Programmable Parameter Table Required Setting

Engine Gear Parameters

Transmission Type Allison-MD

Engine Family Rating Code 1121-210/520

1141-225/560

1122-225/620

2141-255/660

2131-245/620

2132-245/660

Configuration

Engine

Hybrid (HEV)

Programmable Parameter Table Required Setting

Engine Parameters

Transmission Type Eaton Hybrid (Allison-MD in Service Tool)

EFRC: ENgine Family Rating Code 1121-210/560

PTO: Remote Pedal Off, Unless Approved by Eaton Application Engineering

1131-225/560

1141-225/620

1151-230/620

2121-245/620

2131-255/660

12

Engine Configuration

International (EPA 2007 Emission Engines MaxxForce 11 and 13)

UltraShift Heavy-Duty DM

Features and Parameters Required Setting

Engine Family / Transmission

Transmission Type 8: Eaton Ultrashift

Low Idle Engine Speed 700 rpm maximum

Low Idle Speed Adjustable Maximum 700 rpm maximum

Vehicle Configuration

Speed Governor Enable 0: Torque Governor Enabled

Engine Fan Control

Engine Fan Control Mode 3: Variable Engine Fan Speed Control

Enable the fan on with engine braking feature 1: Enable (Navistar Requirement)

UltraShift PLUS Heavy-Duty

Features and Parameters Required Setting

Engine Family / Transmission

Transmission Type 8: Eaton Ultrashift

Vehicle Configuration

Speed Governor Enable 0: Torque Governor Enabled

Engine Fan Control

Engine Fan Control Mode 3: Variable Engine Fan Speed Control

13

Enable the fan on with engine braking feature 1: Enable (Navistar Requirement)

Engine Configuration

International (EPA 2010 Emission Engines MaxxForce 11 and 13)

UltraShift Heavy-Duty DM

Features and Parameters Required Setting

Engine Family / Transmission

Transmission Type 8: Eaton Ultrashift

Low Idle Engine Speed 700 rpm maximum

Low Idle Speed Adjustable Maximum 700 rpm maximum

Engine Fan Control

Engine Fan Control Mode 1.0: On/Off Control OR

UltraShift PLUS Heavy-Duty

Features and Parameters Required Setting

Engine Family / Transmission

Transmission Type 8: Eaton Ultrashift

Vehicle Configuration

Configuration

Engine

2.0: Variable Engine Fan Speed Control

High Idle Engine Speed 2100-2200 rpm

Engine Fan Control

Engine Fan Control Mode 1.0: On/Off Control OR

2.0: Variable Engine Fan Speed Control

14

UltraShift PLUS Heavy-Duty

Engine Gear Parameters

Engine Configuration

ID Gear

Number
Calcula-

tion

Gear #

82201 1 GNCG1 18

Abbrevi-

ation

Value ID Gear

Number
Calcula-

tion

Ratio #

82431 1 GNCR1 NA NA 0.73 NA NA NA NA NA

Abbrevi-

ation

10C
LAS

10B
LAS

MXP

VXP

VMS VCS MHP 10-Sp

DM3

10B
LST

82211 2 GNCG2 17 82441 2 GNCR2 NA NA 0.86 NA NA NA NA NA

82221 3 GNCG3 16 82451 3 GNCR3 NA NA 1.00 NA NA NA NA NA

82231 4 GNCG4 15 82461 4 GNCR4 NA NA 1.17 NA NA NA NA NA

82241 5 GNCG5 14 82471 5 GNCR5 NA NA 1.38 NA NA NA NA NA

82251 6 GNCG6 13 82481 6 GNCR6 NA NA 1.62 NA NA 0.73 NA NA

82261 7 GNCG7 12 82491 7 GNCR7 NA NA 1.94 NA NA 0.86 NA NA

82271 8 GNCG8 11 82501 8 GNCR8 NA NA 2.28 0.73 NA 1.00 NA NA

82281 9 GNCG9 10 82511 9 GNCR9 0.73 1.00 2.73 1.00 0.74 1.17 0.74 1.00

82291 10 GNCG10 9 82521 10 GNCR10 1.00 1.34 3.20 1.38 1.00 1.38 1.00 1.34

82301 11 GNCG11 8 82531 11 GNCR11 1.38 1.83 3.74 1.95 1.36 1.62 1.36 1.83

82311 12 GNCG12 7 82541 12 GNCR12 1.89 2.46 4.38 2.77 1.83 1.95 1.83 2.46

82321 13 GNCG13 6 82551 13 GNCR13 2.61 3.30 5.16 3.79 2.53 2.29 2.46 3.31

82331 14 GNCG14 5 82561 14 GNCR14 3.58 4.67 6.05 5.23 3.40 3.20 3.32 4.46

82341 15 GNCG15 4 82571 15 GNCR15 4.90 6.28 7.29 7.41 4.63 4.38 4.46 6.00

82351 16 GNCG16 3 82581 16 GNCR16 6.76 8.55 8.51 11.85 6.24 6.05 6.07 8.17

82361 17 GNCG17 2 82591 17 GNCR17 9.25 11.52 12.29 16.30 9.42 8.51 8.18 11.00

82371 18 GNCG18 1 82601 18 GNCR18 12.80 15.42 14.40 26.08 14.56 12.29 10.96 14.78

82381 19 GNCG19 -2 82611 19 GNCR19 NA NA NA NA NA NA NA NA

Gear Number Values on Left Correspond to Ratio Values on Right

82391 20 GNCG20 -2 82621 20 GNCR20 NA NA NA NA NA NA NA NA

82401 21 GNCG21 -2 82631 21 GNCR21 NA NA NA NA NA NA NA NA

82411 22 GNCG22 -2 82641 22 GNCR22 NA NA NA NA NA NA NA NA

82421 23 GNCG23 -2 82651 23 GNCR23 NA NA NA NA NA NA NA NA

Note: For engine parameters not listed above, please refer to the engine manufactures programming guide.

Note: In order for Progressive Shift and Gear Down protection to work correctly, the gear number and ratio information must be

set correctly. Progressive Shift and Gear Down protection settings can effect transmission operation and should be
reviewed when diagnosing a shift complaint.

15

International MaxxForce

Hybrid (HEV)

Programmable Parameter Table Required Setting

Engine Parameters

Engine Configuration

Transmission Type Eaton Hybrid (Allison-MD in Service Tool)

EFRC: ENgine Family Rating Code 1121-210/560

1131-225/560

1141-225/620

1151-230/620

2121-245/620

2131-255/660

PTO: Remote Pedal Off, Unless Approved by Eaton Application Engineering

Configuration

Engine

16

Detroit Diesel (pre 2007)

AutoShift Heavy-Duty

Calibration Parameters Required Setting

Transmission Type 16 – AutoShift J1939 Transmission

UltraShift Heavy-Duty DM

Calibration Parameters Required Setting

Transmission Type 14 – Automatic w/magnetic speed sensor

Engine Configuration

33 – Eaton Fuller Automatic w/J1939 Speed

(Setting the listed transmission types above sets a
maximum warmup speed of 700 rpm.)

Enable_VSG_switch OFF or limit below

VSG_max_rpm 650 rpm

Analog D1 510 (DDEC IV) NONE (No analog PTO input allowed)

Detroit Diesel (EPA 2010 Emission Engines DD13, DD15, DD16)

AutoShift - Heavy-Duty

Parameter Group Parameters Required Setting

MCM2 Trans Limp Home Mode 1- Automatic

2 Transmission Type DIRECT ENGINE START

2 - Eaton AutoShift Direct Start
MCM ENGINE START
5 - Eaton AutoShift MCM Start

3 Max Engine Speed 3000 rpm (to allow for engine

protection upshift)

5 LIM0, LIM1, LIM2 1800 rpm or higher

10 Eng Brk Driveline Clsd Min Spd 800 rpm

10 Min Eng Spd for Engine Brakes 1100 rpm

13 Clutch Switch Config 1 - Clutch Switch

13 4 08 DI Selection 1 - Clutch Switch

13 Trans Neutral Input Config 1 - Info from J1939

17

Engine Configuration

UltraShift - Heavy-Duty DM

Parameter Group Parameters Required Setting

MCM2 Trans Limp Home Mode 1= Automatic

2 Transmission Type DIRECT ENGINE START

2 = Eaton UltraShift Direct Start
MCM ENGINE START
5 = Eaton UltraShift MCM Start

3 Adjusted Idle Configuration 0 = Disabled

3 = Enabled if Neutral and Park Brake

3 Max Adjusted Idle Speed <700 rpm

3 Max Engine Speed 3000 rpm (to allow for engine

protection upshift)

3 Min Engine Speed <700 rpm

5 LIM0, LIM1, LIM2 1800 rpm or higher

Configuration

Engine

6 Fast Idle Spd Air Cond Input <700 rpm

7 Configuration PTO Speed Control 3 = Enable if Neutral and park brake

0 = Disable

7 Max Road Speed in PTO Mode 10.0 km/h or 6 mi/h (default)

7 PTO Droptout Serv Brk Prk Brk If PTO is enabled,

2 = PTO Drops out on Service Brake
Activation

8 Anti Tamper (Vehicle Speed Tamper) 0 = Disabled

8 Vehicle Speed Sensor 3 = J1939 (ETC1)

10 Eng Brk Driveline Clsd Min Spd 800 rpm

10 Min Eng Spd for Engine Brakes 1100 rpm

13 Clutch Switch Config 0 = Disabled (No Clutch Switch)

13 4 08 DI Selection 0 = Disabled

13 Trans Neutral Input Config 1 = Info from J1939

15 Enabled Cruise Auto Resume 3 = Resume AMT Style

UltraShift PLUS Heavy-Duty

Parameter Group Parameters Required Setting

2 Transmission Type MCM ENGINE START

5 = Eaton UltraShift MCM2 Start

3 Max Engine Speed > 2000 rpm

18

Engine Configuration

Parameter Group Parameters Required Setting

5 Limiter0 Max Eng Speed Enabled > 2000 rpm

5 Limiter1 Max Eng Speed Enabled > 2000 rpm

7 Configuration PTO Speed Control 3 = Enable if Neutral and park brake

0 = Disable

8 Vehicle Speed Sensor 3 = J1939 (ETC1)

10 Eng Brk Driveline Clsd Min Spd 800 rpm

10 Min Eng Spd for Engine Brakes 1100 rpm

13 Clutch Switch Config 0 = Disabled (No Clutch Switch)

13 4 08 DI Selection 0 = Disabled

13 Trans Neutral Input Config 1 = Info from J1939 (Multiplexed)

15 Enabled Cruise Auto Resume 3 = Resume AMT Style

MCM2
4_1_EngineConfig

Trans Limp Home Mode 1 = Automatic

Detroit Diesel/Mercedes (EPA 2007 Emission Engines)

AutoShift - Heavy-Duty

Parameter Group Parameters Required Setting

MCM Trans Limp Home Mode 1- Automatic

2 Transmission Type DIRECT ENGINE START

2 - Eaton AutoShift Direct Start
MCM ENGINE START
5 - Eaton AutoShift MCM Start

3 Max Engine Speed 3000 rpm (to allow for engine

protection upshift)

5 LIM0, LIM1, LIM2 1800 rpm or higher

10 Eng Brk Stage 1 Off Delay Time 60 ms - Series 60DD15 Engine

240ms - MBE 900/4000

10 Eng Brk Stage 2 Off Delay Time 60 ms - Series 60/DD15 Engine

240 ms - MBE 900/4000

10 Eng Brk Stage 3 Off Delay Time 60 ms - Series 60/DD15 Engine

240 ms - MBE 900/4000

10 Stage 1 Eng Brk Off Delta Spd 250 rpm - Series 60

200rpm - DD15
100rpm - MBE 900/4000

19

Engine Configuration

Parameter Group Parameters Required Setting

10 Stage 2 Eng Brk Off Delta Spd 250 rpm - Series 60

200rpm - DD15
100rpm - MBE 900/4000

10 Stage 3 Eng Brk Off Delta Spd 250 rpm - Series 60

200rpm - DD15
100rpm - MBE 900/4000

10 Eng Brk Driveline Clsd Min Spd 800 rpm

10 Min Eng Spd for Engine Brakes 1100 rpm

10 Trans Mask Engine Brake Series 60 - 81 : decompression valve

and turbo brake or Jake Brake 3rd
stage
DD15 Engine - 64: decompression
valve only or Jake Brake 1st Stage
MBE 4000 - 0: no engine brake
activation

Configuration

Engine

10 Trans Factor Engine Brake 100

13 Clutch Switch Config 1 - Clutch Switch

13 4 08 DI Selection 1 - Clutch Switch

13 Trans Neutral Input Config 1 - Info from J1939

22 0 Speed Gov TSC1 Condition 0 - Series 60/DD15/MBE 4000

16 - MBE 900

22 1 Speed Gov TSC1 Condition 0 - Series 60/DD15/MBE 4000

16 - MBE 900

22 2 Speed Gov TSC1 Condition 0 - Series 60/DD15/MBE 4000

16 - MBE 900

22 3 Speed Gov TSC1 Condition 0 - Series 60/DD15/MBE 4000

16 - MBE 900

23 Acceleration Limiter Ramp Up Rate 160 rpm/sec (default) or higher (Al

Guide states S60 should be 120 rpm/
sec)

44 Mode Shift ECAN Status Enable 0 - Disable - Series 60/MBE 900/

DD15
1 - Enable - MBE 4000

UltraShift - Heavy-Duty DM

Parameter Group Parameters Required Setting

MCM Trans Limp Home Mode 1- Automatic

20

Engine Configuration

Parameter Group Parameters Required Setting

2 Transmission Type DIRECT ENGINE START

2 - Eaton UltraShift Direct Start
MCM ENGINE START
5 - Eaton UltraShift MCM Start

3 Adjusted Idle Configuration 0 - Disabled

3 - Enabled if Neutral and Park Brake

3 Max Adjusted Idle Speed <650 rpm

3 Max Engine Speed 3000 rpm (to allow for engine

protection upshift)

3 Min Engine Speed <650 rpm

5 LIM0, LIM1, LIM2 1800 rpm or higher

6 Fast Idle Spd Air Cond Input <700 rpm

7 Configuration PTO Speed Control 3 - Enable if Neutral and park brake

0 - Disable

7 Max Road Speed in PTO Mode 10.0 km/h or 6 mi/h (default)

7 PTO Droptout Serv Brk Prk Brk If PTO is enabled,

2 - PTO Drops out on Service Brake
Activation

8 Anti Tamper (Vehicle Speed Tamper) 0 - Disabled

8 Vehicle Speed Sensor 3 - J1939 (ETC1)

10 Trans Mask Engine Brake Series 60 - 81 : decompression valve

and turbo brake or Jake Brake 3rd
stage
DD15 Engine - 64: decompression
valve only or Jake Brake 1st Stage
MBE 4000 - 0: no engine brake
activation

10 Trans Factor Engine Brake 100

10 Eng Brk Stage 1 Off Delay Time 60 ms - Series 60DD15 Engine

240 ms - MBE 900/4000

10 Eng Brk Stage 2 Off Delay Time 60 ms - Series 60/DD15 Engine

240 ms - MBE 900/4000

10 Eng Brk Stage 3 Off Delay Time 60 ms - Series 60/DD15 Engine

240 ms - MBE 900/4000

10 Stage 1 Eng Brk Off Delta Spd 250 rpm - Series 60

200rpm - DD15
100rpm - MBE 900/4000

21

Engine Configuration

Parameter Group Parameters Required Setting

10 Stage 2 Eng Brk Off Delta Spd 250 rpm - Series 60

200rpm - DD15
100rpm - MBE 900/4000

10 Stage 3 Eng Brk Off Delta Spd 250 rpm - Series 60

200rpm - DD15
100rpm - MBE 900/4000

10 Eng Brk Driveline Clsd Min Spd 800 rpm

10 Min Eng Spd for Engine Brakes 1100 rpm

13 Clutch Switch Config 0 - Disabled (No Clutch Switch)

13 4 08 DI Selection 0 - Disabled

13 Trans Neutral Input Config 1 - Info from J1939

15 Enabled Cruise Auto Resume 1- Enable automatic resume function

after clutch has been released once

Configuration

Engine

22 0 Speed Gov TSC1 Condition 0 - Series 60/DD15/MBE 4000

16 - MBE 900

22 1 Speed Gov TSC1 Condition 0 - Series 60/DD15/MBE 4000

16 - MBE 900

22 2 Speed Gov TSC1 Condition 0 - Series 60/DD15/MBE 4000

16 - MBE 900

22 3 Speed Gov TSC1 Condition 0 - Series 60/DD15/MBE 4000

16 - MBE 900

23 Acceleration Limiter Ramp Up Rate 160 rpm/sec (default) or higher (Al

Guide states S60 should be 120 rpm/
sec)

23 AL Conditions 1 - No AL During Shift

44 Mode Shift ECAN Status Enable 0 - Disable - Series 60/MBE 900/

DD15
1 - Enable - MBE 4000

UltraShift PLUS Heavy-Duty

Parameter Group Parameters Required Setting

MCM Trans Limp Home Mode 1- Automatic

2 Transmission Type DIRECT ENGINE START

2 - Eaton UltraShift Direct Start
MCM ENGINE START
5 - Eaton UltraShift MCM Start

22

Engine Configuration

Parameter Group Parameters Required Setting

3 Adjusted Idle Configuration 0 - Disabled

3 - Enabled if Neutral and Park Brake

3 Maximum Engine Speed 3000 rpm (to allow for engine

protection upshift)

5 LIMO, LIM1, LIM2 1800 rpm or higher

7 Configuration PTO Speed Control 0 - Disable

3 - Enable if Neutral and Park Brake

8 Anti-Tamper (Vehicle Speed Tamper) 0 - Disabled

8 Vehicle Speed Sensor 3 - J1939 (ETC1)

13 Clutch Switch Config 0 - Disabled (No Clutch Switch)

13 4 08 DI Selection 0 - Disabled

13 Trans Neutral Input Config 1 - Info from J1939

15 Enable Cruise Auto Resume 1 - Enable automatic resume function

after clutch has been released once

22 0 Speed Gov TSC1 Condition 0 - Series 60/DD15 Engine/MBE 4000

16 - MBE 900

22 1 Speed Gov TSC1 Condition 0 - Series 60/DD15 Engine/MBE 4000

16 - MBE 900

22 2 Speed Gov TSC1 Condition 0 - Series 60/DD15 Engine/MBE 4000

16 - MBE 900

22 3 Speed Gov TSC1 Condition 0 - Series 60/DD15 Engine/MBE 4000

16 - MBE 900

23 Acceleration Limiter Ramp Up Rate 160 rpm/sec (default) or higher

(AI Guide states S60 should be 120
rpm/sec)

23 AL Conditions 1 - No AL During Shift

44 Mode Shift

ECAN Status Enable

0 - Series 60/MBE 900/DD15 Engine
1 - MBE 4000

Mercedes (pre 2007)

AutoShift Medium-Duty

Calibration Parameters Required Setting

1 02 01 Transmission Type 1 (Automated with clutch switch)

1 05 xx LIM0, LIM1, LIM2 1800 rpm or higher

23

Engine Configuration

Calibration Parameters Required Setting

1 03 02 Maximum Engine Speed 3000 rpm (to allow for engine protection upshift)

1 10 20 Engine Brake Transmission Mask 16, if exhaust flap otherwise 64, decompression

1 13 07 Enable Transmission Neutral Input 0, J1939

Engine Brake Transmission Factor Parameter 19 = 100

1 23 06, 07 Progressive Shift Limiters No Limits (leave 3000 rpm default)

1 19 01 Enable Automatic Fan on Engine brk. 0, disable

1 23 10 Acceleration Limiter Ramp Rate 160 rpm/sec or higher

AutoShift Heavy-Duty

Calibration Parameters Required Setting

1 02 01 Transmission Type 1 (Automated with clutch switch)

1 05 xx LIM0, LIM1, LIM2 1800 rpm or higher

1 03 02 Maximum Engine Speed 3000 rpm (to allow for engine protection upshift)

1 10 20 Engine Brake Transmission Mask 16, if exhaust flap otherwise 64, decompression

1 13 07 Enable Transmission Neutral Input 0, J1939

Engine Brake Transmission Factor Parameter 19 = 100

1 23 06, 07 Progressive Shift Limiters No Limits (leave 3000 rpm default)

Configuration

Engine

1 19 01 Enable Automatic Fan on Engine brk. 0, disable

1 23 10 Acceleration Limiter Ramp Rate 160 rpm/sec or higher

UltraShift ASW

Calibration Parameters Required Setting

PLD Group 0 01 02 Manual/Automatic Trans 0 MANUAL

1 02 01 Transmission Type 2 (Automatic Trans without clutch switch)

1 03 01 Minimum Engine Speed 800-900 rpm

1 03 02 Maximum Engine Speed 3000 rpm (to allow for engine protection upshift)

(NOT 1 Automatic; engine speed may go to 1300 rpm
with CAN failure.)

Allison name may appear for this setting

24

Calibration Parameters Required Setting

1 03 10 Max Adj. Idle Speed 900 rpm

1 05 xx LIM0, LIM1, LIM2 2200 rpm or higher

1 08 10 Anti Tamper (Vehicle Speed Tamper) 0, disabled

1 13 07 Enable Transmission Neutral Input 0, J1939

1 23 06, 07 Progressive Shift Limiters No Limits (leave 3000 rpm default)

1 23 10 Acceleration Limiter Ramp Rate 160 rpm/sec or higher

UltraShift Medium-Duty DM

Calibration Parameters Required Setting

Engine Configuration

PLD Group 0 01 02 Manual/Automatic Trans 0 MANUAL

(NOT 1 Automatic; engine speed may go to 1300 rpm
with CAN failure.)

1 02 01 Transmission Type 2 (Automatic Trans without clutch switch)

Allison name may appear for this setting

1 03 02 Maximum Engine Speed 3000 rpm (to allow for engine protection upshift)

1 03 10 Max Adj. Idle Speed 650 rpm or lower

1 05 xx LIM0, LIM1, LIM2 1800 rpm or higher

1 06 01 Enable Fast Idle on AC 1, enable fast idle only in Neutral

1 07 01 Configuration PTO Speed Control 3, enable if neutral and park brake – or 2, neutral

1 07 08 PTO Max Vehicle Speed 2 mph

1 07 06 PTO Dropout on Service Brake 2, Dropout on service brake

1 08 10 Anti Tamper (Vehicle Speed Tamper) 0, disabled

1 10 20 Engine Brake Transmission Mask 16, if exhaust flap otherwise 64, decompression

Engine Brake Transmission Factor 100 (parameter 19)

25

1 13 07 Enable Transmission Neutral Input 0, J1939

1 19 01 Enable Automatic Fan on Engine brk. 0, disable

1 23 06, 07 Progressive Shift Limiters No Limits (leave 3000 rpm default)

1 23 10 Acceleration Limiter Ramp Rate 160 rpm/sec or higher

UltraShift Heavy-Duty

Calibration Parameters Required Setting

PLD Group 0 01 02 Manual/Automatic Trans 0 MANUAL

1 02 01 Transmission Type 2 (Automatic Trans without clutch switch)

1 03 02 Maximum Engine Speed 3000 rpm (to allow for engine protection upshift)

1 03 10 Max Adj. Idle Speed 650 rpm or lower

1 05 xx LIM0, LIM1, LIM2 1800 rpm or higher

1 06 01 Enable Fast Idle on AC 1, enable fast idle only in Neutral

Engine Configuration

(NOT 1 Automatic; engine speed may go to 1300 rpm
with CAN failure.)

Configuration

Engine

Allison name may appear for this setting

1 07 01 Configuration PTO Speed Control 3, enable if neutral and park brake – or 2, neutral

1 07 08 PTO Max Vehicle Speed 2 mph

1 07 06 PTO Dropout on Service Brake 2, Dropout on service brake

1 08 10 Anti Tamper (Vehicle Speed Tamper) 0, disabled

1 10 20 Engine Brake Transmission Mask 16, if exhaust flap otherwise 64, decompression

Engine Brake Transmission Factor 100 (parameter 19)

1 13 07 Enable Transmission Neutral Input 0, J1939

1 19 01 Enable Automatic Fan on Engine brk. 0, disable

1 23 06, 07 Progressive Shift Limiters No Limits (leave 3000 rpm default)

1 23 10 Acceleration Limiter Ramp Rate 160 rpm/sec or higher

For engine parameters not listed above, please refer to the engine manufactures programming guide.

Other applicable documents:

1. • Maximum Engine Load in PTO

• –Eaton FUL-169 & FUL-169U requirements

2. • Maximum PTO Speed

• –Eaton FUL-169 & FUL-169U requirements

26

Engine Configuration

PACCAR MX 12.9L Engine Configuration Settings

Feature and Parameters Required Setting

Auto-Retard Vehicle Speed Offset (N014) 4 MPH, if NeutralCoast is active on Transmission

Please work with an Authorized Kenworth or Peterbilt Dealer to verify engine configuration.

Any feature change may be specified during the vehicle order process. Changing transmission features require new engine soft­ware. Dealers will need to submit a SupportNet case to the PACCAR Engine Support Center to obtain updated software.

If there is a question, the dealer can call the PACCAR Engine Support Center to determine the proper vehicle configuration.

Volvo/Mack Engine Configuration Settings

Please work with an Authorized Volvo or Mack Dealer to verify engine configuration.

The dealer can refer to the COLA system that can associate the proper sub-data set for the transmission/engine combination.
Using Professional Tech Tool (PTT) or VCADS service tool, the dealer can confirm that the vehicle is configured properly. If there
is a question, the dealer can call Volvo’s eService help desk to determine the original sub-data sets for proper vehicle configura
tion.

-

Volvo/Mack Body Builder Module Settings

Parameter ID: DXM (EngSpd Limit) must be set to 0 (OFF)

Please work with an Authorized Volvo or Mack Dealer to verify all other Body Builder Module Settings.

27

Change Control Log

Change Control Log

Change Control Log

Last Revised Date Description of Clarifications and Updates

Sep 2015 Added SmartCoast settings for Cummins UltraShift PLUS Heavy-Duty

Added Procision Transmission settings
Updated PACCAR MX 12.9L Engine Configuration Settings

Nov 2014 Changed all settings for UltraShift PLUS MHP from 13B to 13A.

Oct 2011 Added High Idle Engine Speed to the UltraShift PLUS Heavy-Duty section, along with the Engine Gear

Parameters Table
Added UltraShift PLUS Heavy-Duty Parameters Table to Detroit Diesel (EPA 2010 Emission Engines
DD13, DD15, DD16 Section
Moved the Detroit Diesel (EPA 2010 Emission Engines DD13, DD15, DD16) AutoShift - Heavy-Duty Ta­ble to be before the Detroit Diesel (EPA 2010 Emission Engines DD13, DD15, DD16) UltraShift - Heavy­Duty DM Table
Rearranged the engine Configuration types for usability

Dec 2010 Added sections for 2010 Maxxforce DT engine, Hino, and Maxxforce 11 & 13 for 2010

Sep 2010 Updated Engine Configuration Settings for Volvo and Mack

Dec 2009 Change ECA to UltraShift PLUS, minor changes to UltraShift PLUS tables, add 2010 Detroit Diesel /

Mercedes engine information, add International EPA 2007 engine information

Feb 2009 Add Heavy-Duty ECA tables for Cummins, Caterpillar, and Detroit Diesel / Mercedes

July 2008 Updated International/Maxxforce with Hybrid engine configuration settings, Added Cummins with

Hybrid engine configuration settings, Added DDEC/MBE engine configuration settings for 2007 and
later

May 2008 Changed title from Installation Guide to Engine Configuration

Jun 2007 Updated Caterpillar and Cummins engine configuration settings pages 1, 3, 4, 5, 7, and 8

Jan 2007 Update Engine Configuration Settings, Add new covers, Add Change Control Log

28

Copyright Eaton, 2015.
Eaton hereby grant their customers,
vendors, or distributors permission
to freely copy, reproduce and/or
distribute this document in printed
format. It may be copied only in
its entirety without any changes or
modifications. THIS INFORMATION
IS NOT INTENDED FOR SALE OR
RESALE, AND THIS NOTICE MUST
REMAIN ON ALL COPIES.

Note: Features and specifications
listed in this document are subject to
change without notice and represent
the maximum capabilities of the
software and products with all options
installed. Although every attempt has
been made to ensure the accuracy of
information contained within, Eaton
makes no representation about the
completeness, correctness or accuracy
and assumes no responsibility for
any errors or omissions. Features and
functionality may vary depending on
selected options.

For spec’ing or service assistance,
call 1-800-826-HELP (4357) or visit
www.eaton.com/roadranger.
In Mexico, call 001-800-826-4357.

Roadranger: Eaton and trusted partners
providing the best products and services in the
industry, ensuring more time on the road.

Eaton

Vehicle Group
P.O. Box 4013
Kalamazoo, MI 49003 USA
800-826-HELP (4357)
www.eaton.com/roadranger

Printed in USA