D-link DGS-1024A User Manual [ru]
®
D-Link
DGS-1016A
DGS-1024A
16/24-Port 10/100/1000Mbps
Gigabit Ethernet Switch
(Plastic Case)
Manual
Building Networks for People
RECYCLABLE
(May 2012)
V 1.00
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch
Information in this document is subject to change without notice.
© 2012 D-Link Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is
strictly forbidden.
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation;
Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities
claiming the marks and names or their products. D-Link Corporation disclaims any proprietary
interest in trademarks and trade names other than its own.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with this user’s guide, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference
in which case the user may be required to take adequate measures.
Warnung!
Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen
verursachen. In diesem Fall kann vom Benutzer verlangt werden, angemessene Massnahmen
zu ergreifen.
Precaución!
Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio,
en cuyo case, puede requerirse al usuario para que adopte las medidas adecuadas.
Attention!
Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer
des interférences radio, auquel cas l`utilisateur devrait prendre les mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può
causare interferenze radio, nel cui caso è possibile che l`utente debba assumere provvedimenti
adeguati.
VCCI Warning
警告使用者：
這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會
被要求採取某些適當的對策。
ii
CONTENTS
PREFACE……………………………………………………………… IV
NOTES, NOTICES, AND CAUTIONS ............................................................ IV
SAFETY INSTRUCTIONS .............................................................................. V
Protecting Against Electrostatic Discharge ..................................... vii
INTRODUCTION 8
ABOUT THIS GUIDE ................................................................................... 8
SWITCH DESCRIPTION ............................................................................... 8
Switch Features .................................................................................. 9
D-LINK GREEN TECHNOLOGY ................................................................ 10
FRONT-PANEL COMPONENTS .................................................................. 11
LED Indicators ................................................................................. 12
REAR PANEL DESCRIPTION ..................................................................... 13
INSTALLATION 14
Package Contents ............................................................................. 14
BEFORE YOU CONNECT TO THE NETWORK ............................................ 15
Mounting the Switch on a Rack ........................................................ 16
POWER ON ............................................................................................... 17
Power Failure ................................................................................... 17
CONNECTING THE SWITCH 18
Connect to an End Node ................................................................... 19
Connect to Hub or Switch ................................................................. 20
Connect to Network Backbone or Server .......................................... 21
TECHNICAL SPECIFICATIONS 22
GLOSSARY……………………………………………………………..25
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch
Preface
The DGS-1016A/DGS-1024A Manual is divided into sections that describe the
system installation and operating instructions with examples.
Section 1, Introduction - A description of the physical features of the Switch,
including LED indicators, ports and panel descriptions.
Section 2, Installation – A description of the physical installation of the Switch,
mounting the Switch in a equipment rack and powering on the Switch.
Section 3, Connecting the Switch – A description of how to connect your
Switch to an end node, hub, another switch or backbone server.
Appendix Technical Specifications - The technical specifications of the
DGS-1016A/DGS-1024A.
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information
that helps you make better use of your device.
NOTICE: A NOTICE indicates either potential
damage to hardware or loss of data and tells you
how to avoid the problem.
CAUTION: A CAUTION indicates the potential for
property damage, personal injury or death.
iv
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch
Safety Instructions
Use the following safety guidelines to ensure your own personal safety and to help protect your
system from potential damage. Throughout this safety section, the caution icon ( ) is used to
indicate cautions and precautions that you need to review and follow.
Safety Cautions
To reduce the risk of bodily injury, electrical shock, fire, and damage to the
equipment, observe the following precautions.
Observe and follow service markings. Do not service any product except as
explained in your system documentation. Opening or removing covers that are
marked with the triangular symbol with a lightning bolt may expose you to an
electrical shock. Only a trained service technician should service components inside
these compartments.
If any of the following conditions occur, unplug the product from the electrical outlet
and replace the part or contact your trained service provider:
– The power cable, extension cable, or plug is damaged.
– An object has fallen into the product.
– The product has been exposed to water.
– The product has been dropped or damaged.
– The product does not operate correctly when you follow the operating
instructions.
Keep your system away from radiators and heat sources. Also, do not block
cooling vents.
Do not place any device on top of Switch, or place the Switch on top of any
device or object that will block the free flow of air through the ventilation slots on
the sides, top, and bottom of the Switch’s case.
Keep your hand away from top and bottom of device that generates a
significant amount of heat.
Do not spill food or liquids on your system components, and never operate the
product in a wet environment. If the system gets wet, see the appropriate
section in your troubleshooting guide or contact your trained service provider.
Do not push any objects into the openings of your system. Doing so can cause
a fire or an electric shock by shorting out interior components.
Use the product only with approved equipment.
Allow the product to cool before removing covers or touching internal
components.
Operate the product only from the type of external power sourc e indicated on
the electrical ratings label. If you are not sure of the type of power source
required, consult your service provider
or local power company.
v
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch
Safety Instructions (continued)
To help avoid damaging your system, be sure the voltage selection Switch (if
provided) on the power supply is set to match the power available at your
location:
– 115 volts (V)/60 hertz (Hz) in most of North and South America and
some Far Eastern countries such as South Korea and Taiwan
– 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan.
– 230 V/50 Hz in most of Europe, the Middle East, and the Far East.
Also be sure that attached devices are electrically rated to operate with the
power available in your location.
Use only approved power cable(s). If you have not been provided with a power
cable for your system or for any AC-powered option intended for your system,
purchase a power cable that is approved for use in your country. The powe r
cable must be rated for the product and for the voltage and current marked on
the product's electrical ratings label. The voltage and current rating of the cable
should be greater than the ratings marked on the product.
To help prevent an electric shock, plug the system and peripheral power cables
into properly grounded electrical outlets. These cables are equipped with threeprong plugs to help ensure proper grounding. Do not use adapter plugs or
remove the grounding prong from a cable. If you must use an extension cable,
use a 3-wire cable with properly grounded plugs.
Observe extension cable and power strip ratings. Make sure that the total
ampere rating of all products plugged into the extension cable or power strip
does not exceed 80 percent of the ampere ratings limit for the extension cable
or power strip.
To help protect your system from sudden, transient increases and decreases in
electrical power, use a surge suppressor, line conditioner, or uninterruptible
power supply (UPS).
Position system cables and power cables carefully; route cables so that they
cannot be stepped on or tripped over. Be sure that nothing rests on any cables.
Do not modify power cables or plugs. Consult a licensed electrician or your
power company for site modifications. Always follow your local/national wiring
rules.
When connecting or disconnecting power to hot-pluggable power supplies, if
offered with your system, observe the following guidelines:
– Install the power supply before connecting the power cable to the power
supply.
– Unplug the power cable before removing the power supply.
– If the system has multiple sources of power, disconnect power from the
system by unplugging all power cables from the power supplies.
Move products with care; ensure that all casters and/or stabilizers are firmly
connected to the system. Avoid sudden stops and uneven surfaces.
vi
D-Link DGS-1016A/DGS-1024A Unmanaged Gigabit Ethernet Switch
Protecting Against Electrostatic Discharge
Static electricity can harm delicate components inside your system. To prevent static
damage, discharge static electricity from your body before you touch any of the
electronic components, such as the microprocessor. You can do so by periodically
touching an unpainted metal surface on the chassis.
You can also take the following steps to prevent damage from electrostatic
discharge (ESD):
1. When unpacking a static-sensitive component from its shipping carton, do
not remove the component from the antistatic packing material until you
are ready to install the component in your system. Just before unwrapping
the antistatic packaging, be sure to discharge static electricity from your
body.
2. When transporting a sensitive component, first place it in an antistatic
container or packaging.
3. Handle all sensitive components in a static-safe area. If possible, use
antistatic floor pads, workbench pads, and an antistatic grounding strap.
vii
SECTION 1
Introduction
About This Guide
Switch Description
Switch Features
D-Link Green Technology
Ports
Front-Panel Components
LED Indicators
Power Input on Rear Panel
About This Guide
Congratulations on your purchase of the DGS-1016A/DGS-1024A
16/24-port 10/100/1000Mbps Gigabit Ethernet Switch. These devices
are using compact plastic case and are highly flexible solution for
SOHO or small office customers.
Switch Description
The 16-port DGS-1016A and 24-port DGS-1024A Switches provide
dedicated 10, 100 or 1000 Mbps Ethernet bandwidth on each port. The
ports will automatically detect the speed, duplex and MDI/MDIX status
of the device it is connecting to, and adjust these settings accordingly.
The Switch ports can be used to network computers, printers, servers,
routers, other switches or any device equipped with an Ethernet port.
For best performance, use Category 5 or better Ethernet cabling.
This stand alone Switch is very easy to set up. There is no network
management is required; simply power on the Switch and connect the
cables.
However, please keep in mind that the standard rules of available
Ethernet cable length from one device to another which cannot exceed
100 meters (or 300 feet).
8
Switch Features
The DGS-1016A 16-Port and DGS-1024A 24-port Switches do not
require any management. Both Switches are designed for easy
installation, flexibility and high performance. Connect devices to the
Switch as the scale and volume of network traffic increases.
Support 10/100/1000 Base-T on both 16 and 24 ports models
Store and Forward Switching Method
D-Link Green Technology
Auto Negotiation on Duplex Mode
Auto MDI/MDIX supported
Support Full/Half Duplex Transfer Mode on 10/100 Mbps
Support Full Duplex Transfer Mode on 1000 Mbps
Wire-Speed reception and transmission
8K absolute MAC Address (DGS-1016A) ; 16K absolute MAC
Address (DGS-1024A)
2Mbits RAM for data buffering (DGS-1016A) ; 3.5Mbits RAM for
data buffering (DGS-1024A)
IEEE 802.3x Flow Control for Full-duplex mode
Back Pressure Flow Control for Half-duplex mode
Jumbo Frame support (9216Bytes)
Support IEEE802.3az EEE & D-Link innovative EEE+ for
more power saving
9
Loading...