D-Link DCS-2802KT Installation Guide

1

Plug the supplied Ethernet cable from your router or gateway into
the port marked 'LAN'.
Plug the power adapter into the hub. Make sure the power button is
pressed down into the 'ON' position.

2

SYNC

Once the hub has powered up, press the SYNC button on each
camera to power them on.

3

Scan the QR code above to download the mydlink app for your
Android or iOS device.

4

New Users:

Tap Sign Up to register for a mydlink account, then tap
Add a Device to install your camera. Continue to follow the

onscreen inscructions.

OR

Existing Users:

Sign in using your mydlink account and tap the icon at the
top-left, then tap Add a Device to start the setup wizard.
Continue to follow the onscreen instructions.

5

When prompted, select "Yes" to scan the QR code on the back of the
hub, then continue to follow the onscreen instructions to complete
the setup process.

Note: Please ensure that your mobile device is connected to the Wi-Fi
network of the router that you connected the hub to.

Camera Placement Precautions

Caution:

Proper Placement:

Place the camera at least 2.2 m (7 ft) or higher from the ground. The
minimum recommended viewing distance for the motion detection
is 60 cm (24 in), and the maximum is 7.5 m (25 ft).

2.2 m
(7 ft)

Improper Placement:

Do not place the camera directly on top of a surface or in a spot
where there is something directly below it, obstructing its view

Please make sure that the camera is
not directly facing the sun or a source
of heat.

64°

poor detection

60 cm
(24 in)
min

115°

good detection

7.5 m
(25 ft)
max

.

Camera Mounting Instructions

Snap Mount

Step 1:

Identify and mark the location where you want to
install the bracket, assuring that it is at least 20 cm
from the ceiling.

Step 2:

Using a 6 mm drill bit, drill a 25 mm deep hole over
the mark. For a plaster, drywall, or concrete wall,
insert the plastic anchor to support the screw rst.

Step 3:

Twist the supplied screw into the wall or anchor,
making sure to leave enough clearance between the
screw head and the wall.

Step 4:

Align the screw with the largest hole on the snap
mount. Slide the mount down to lock it into place.

Step 5:

Attach the back of the camera to the mount. Adjust
the angle as desired.

1

2

3

4

5

Camera Mounting Instructions

Threaded Mount

Step 1:

Place the mount at the desired location, assuring
that it is at least 20 cm from the ceiling. Use a pencil
to mark the holes.

Step 2:

Using a 6 mm drill bit, drill two 25 mm deep holes
over the pencil marks. For a plaster, drywall, or
concrete wall, insert the plastic anchors to support
the screws rst.

Step 3:

Place the mount over the holes that are in the wall.
Make sure to align the mount holes with the holes
in the wall. Use the supplied screws to attach the
mount to the surface of the wall.

1

2

3

Step 4:

Rotate the wing nut counterclockwise with your
ngers to slightly loosen it. Then move the bracket
to the approximate desired position.

Step 5:

Screw the camera onto the mounting screw by
tightening the plastic nger nut.

Step 6:

Adjust the angle of the arm on the mounting bracket
as required. Tighten the wing nut to lock the
camera's position into place.

4

5

6

Camera LED Information

DCS-2800LH

Status LED

Green Orange Red

Motion

detected

Pairing

complete

Currently

pairing

N/A

Behavior

Solid

Solid for

10 sec.

Blinking

every
1 sec.

Blinking

every

30 sec.

Color

Fully

charged

N/A

Charging

Less than

10% battery

Malfunction

Pairing failed /

Unpaired

Updating

firmware

Lost wireless

connection

?

Frequently Asked Questions

1) What can I do if my camera is not working properly or I’m
having problems setting it up?

Reset the hub by pressing the Reset button for 10 seconds using a
paper clip, assuring that all the LEDs turn off briefly after releasing the
button. Then try setting it up again in the mydlink app.
In addition, please verify that:

• your Internet connection is active on your router.

• your router’s Wi-Fi is turned on.

• the camera’s battery has enough power.

• your mobile device is connected to the same Wi-Fi network of the
router that you connected the hub to.

2) How do I see my camera feed or adjust its settings?

You can access your camera by tapping the menu icon
left corner of the main menu, select Devices, then select Camera. In the
selected device group page, you can select the specific camera in the
carousel by tapping its icon.

in the top-

Minimum Requirements

To install this product, you will need:

• An 802.11 g/n wireless router

• An Internet connection

• The latest version of the mydlink app from the App Store or
Google Play. Please refer to the app's store page to check whether
your device is compatible.

• An e-mail account (required to register for mydlink service)

Support

For toubleshooting tips and more information, visit:

support.dlink.com

Technical Support

Australia:
Tel: [phone]
24/7 Technical Support
Web: http://www.dlink.com.au
E-mail: [e-mail]

New Zealand:

Tel: [phone]
24/7 Technical Support
Web: http://www.dlink.co.nz
E-mail: [e-mail]

Version 1.00 (AU)_90x130

2018/09/28

Copyright ©2018 All rights reserved. D-Link and the D-Link logo are registered trademarks
of D-Link Corporation or its subsidiaries. Product specifications, size and shape are subject to
change without notice, and actual product appearance may differ from that depicted on the
packaging. Visit dlink.com for more details.

Wire-Free Camera Kit

Quick Start Guide

DCS-2802KT