Loading...
ZENMUSE H20 SERIES
User Manual v1.0
2020.05
Searching for Keywords
Search for keywords such as “battery” and “install” to find a topic. If you are using Adobe Acrobat
Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to begin a search.
Navigating to a Topic
View a complete list of topics in the table of contents. Click on a topic to navigate to that section.
Printing this Document
This document supports high resolution printing.
Using this Manual
Legend
Warning |
Important |
Tips |
DJI Pilot App Download
The DJI Pilot app is required when using Zenmuse H20 series.
Scan the QR code or visit http://www.dji.com/zenmuse-h20-seires/downloads to download and install the app.
2 © 2020 DJI All Rights Reserved.
Caution
1.Please store the camera in a dry and ventilated area at normal temperature, to avoid fogging the lenses due to excessive ambient humidity. If the lenses fog up, the water vapor will usually dissipate after turning on the device for a while. The recommended storage environment is a relative humidity less than 40% at a temperature of 20±5 .
2.Do not expose the infrared camera lenses to a strong energy source such as the sun, lava or laser beam. The temperature of the observation target should not exceed 800 , otherwise it will burn the camera and cause permanent damage.
3.Do not place the product under direct sunlight, in areas with poor ventilation, or near a heat source such as a heater.
4.Do not frequently power on/off the product. After it is turned off, wait at least 30 seconds before turning back on, otherwise the product life will be affected.
5.Under stable laboratory conditions, the Zenmuse H20 series achieves an IP44 protection rating by IEC60529 standards. However, this protection rating is not permanent and may reduce over time after long-term use.
6.Make sure the gimbal port and gimbal surface are free from any liquid before installation.
7.Make sure the gimbal is securely installed onto the aircraft, the microSD card slot cover is clean and firmly in place.
8.Make sure the gimbal surface is dry before opening the microSD card slot cover.
9.Do not plug or unplug the microSD card during use.
10.Do not touch the surface of the camera lenses and keep it away from hard objects, as doing so may lead to blurred images and affect the imaging quality.
11.Clean the surface of the camera lenses with a soft, dry, clean cloth. Do not use alkaline detergents.
© 2020 DJI All Rights Reserved. 3
Contents
Using this Manual |
2 |
Legend |
2 |
DJI Pilot App Download |
2 |
Caution |
3 |
Contents |
4 |
Introduction |
5 |
Installation |
6 |
Supported Aircraft |
6 |
Mounting the Zenmuse H20 Series |
6 |
Remote Controller Operation |
7 |
DJI Pilot App |
8 |
Basic Functions |
8 |
Intelligent Functions |
15 |
Updating Firmware |
16 |
Specifications |
17 |
4 © 2020 DJI All Rights Reserved.
Introduction
The Zenmuse H20 gimbal and camera features a zoom and wide camera. Operators can quickly switch to a high-magnification zoom image for detailed observation after recognizing the target from the wide camera view. The Zenmuse H20T also features a Longwave Infrared Thermal Camera, which can provide both infrared and visual images simultaneously. Both the Zenmuse H20 and H20T are equipped with a laser rangefinder, providing distance and location information applicable to various missions such as search and rescue, inspection, and more. For optimal performance, the Zenmuse H20 Series is compatible with the Matrice 300 RTK aircraft.
Zenmuse H20
|
8 |
|
|
|
1 |
|
|
|
|
|
2 |
1. |
Gimbal Connector |
5. Wide Camera |
|
7 |
|
2. |
Pan Motor |
6. Tilt Motor |
|
|
3 |
3. |
Zoom Camera |
7. Roll Motor |
|
6 |
|
|
|
||||
4. |
Laser Rangefinder |
8. microSD Card Slot |
5 |
4 |
|
|
|
|
|
|
|
Zenmuse H20T |
|
|
|
|
|
|
1 |
|
|
9 |
|
|
2 |
|
|
|
|
|
|
3 |
1. |
Gimbal Connector |
6. Zoom Camera |
8 |
|
4 |
2. |
Pan Motor |
7. Tilt Motor |
|
|
3. |
Wide Camera |
8. Roll Motor |
|
7 |
|
5 |
4. |
Laser Rangefinder |
9. microSD Card Slot |
|
5. |
Infrared Thermal |
|
||
|
|
|
|
||
6 |
|
|
Camera |
|
|
© 2020 DJI All Rights Reserved. 5
Installation
Supported Aircraft
Matrice 300 RTK
Mounting the Zenmuse H20 Series
The following installation display uses the Zenmuse H20 as an example. 1. Remove the gimbal cap and lens protector.
2.Rotate the gimbal connector of the Matrice 300 RTK aircraft to the unlocked position and insert the gimbal, and then rotate the gimbal connector to the locked position.
1
21
31
Hold the gimbal connector firmly and apply a steady, firm rotating force when attaching or detaching the gimbal.
Ensure the microSD card slot cover is firmly in place to prevent dust or moisture entering during usage or transportation.
The Zenmuse H20 series is a delicate instrument. Do not disassemble the gimbal or camera as this will cause permanent damage.
6 © 2020 DJI All Rights Reserved.
Loading...