Delonghi ECAM35055SB User Manual

Download

Page 1

ECAM35X.55

BEAN TO CUP ESPRESSO AND

CAPPUCCINO MACHINE

Instruction for Use

Instructions videos available at:

http://ecam35055.delonghi.com

Page 2

page 6

B10

B12

B11

B13

Page 3

A12

A13

A10

A19

A11

A16

A22

A21

A20

A14

A15

A17

A18

Page 4

2 3B

65 7 8

10 11 12

14 16116

Page 5

18 20

24A

PUSH

26 2827

24B

A B

30 31

Page 6

CONTENTS

1. FUNDAMENTAL SAFETY WARNINGS .............7

2. SAFETY WARNINGS ....................................8

2.1 Symbols used in these instructions ...............8

2.2 Designated use ..............................................8

2.3 Instruction for Use .........................................8

3. INTRODUCTION ..........................................8

3.1 Letters in brackets .........................................8

3.2 Troubleshooting and repairs ..........................8

4. DESCRIPTION.............................................9

4.1 Description of the appliance .........................9

4.2 Description of the accessories ........................9

4.3 Description of the milk container ..................9

5. BEFORE USE...............................................9

5.1 Checking the appliance .................................9

5.2 Installing the appliance .................................9

5.3 Connecting the appliance ............................10

5.4 Setting up the appliance .............................10

6. TURNING THE APPLIANCE ON....................10

7. TURNING THE APPLIANCE OFF ..................10

8. MENU SETTINGS ...................................... 11

8.1 Language ....................................................11

8.2 Maintenance ...............................................11

8.3 Program beverages .....................................11

8.4 Program My beverages................................11

8.5 General .......................................................11

8.6 Statistics ......................................................12

9. RINSING .................................................. 12

10. MAKING COFFEE .......................................13

10.1 Adjusting the coee mill .............................13

10.2 Tips for a hotter coee.................................13

10.3 Making automatic recipes using coee beans .

..................................................................13

10.4 Temporarily varying the coee aroma .........14

10.5 Making coee using pre-ground coee .......14

11. MAKING CAPPUCCINOS AND MILKBASED

COFFEES .................................................. 14

11.1 Filling and attaching the milk container ......15

11.2 Adjusting the amount of froth .....................15

11.3 Making cappuccino and milk-based coees

automatically ..............................................15

11.4 Cleaning the milk container after use .........15

12. “ ” PROGRAMMING AND SELECTING ..

............................................................... 16

13. DELIVERING HOT WATER .......................... 16

14. CLEANING................................................ 16

14.1 Cleaning the machine .................................16

14.2 Cleaning the machine's internal circuit .......16

14.3 Cleaning the coee grounds container ........17

14.4 Cleaning the drip tray and condensate tray .17

14.5 Cleaning the inside of the coee machine ...17

14.6 Cleaning the water tank ..............................17

14.7 Cleaning the coee spouts ..........................17

14.8 Cleaning the pre-ground coee funnel .......17

14.9 Cleaning the infuser ....................................17

14.10 Cleaning the milk container ........................18

14.11 Cleaning the hot water nozzle .....................18

15. DESCALING .............................................. 18

16. SETTING WATER HARDNESS ...................... 19

16.1 Measuring water hardness ..........................19

16.2 Setting water hardness ...............................19

17. WATER SOFTENER FILTER .........................19

17.1 Installing the lter ......................................20

17.2 Replacing the lter ......................................20

17.3 Removing the lter .....................................21

18. TECHNICAL DATA ...................................... 21

19. DISPOSING OF THE APPLIANCE .................21

20. DISPLAYED MESSAGES ..............................21

21. TROUBLESHOOTING ................................. 24

22. ELECTRICAL REQUIREMENTS..................... 26

Page 7

1. FUNDAMENTAL SAFETY WARNINGS

• The appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

• Designated use: this appliance is designed and made to prepare coee and milk

based beverages and hot water. Any other use is considered improper and thus dangerous. The manufacturer is not liable for damage deriving from improper use of the appliance.

• The surface of the heating element remains hot after use and the outside of the appli-

ance may retain the heat for several minutes depending on use.

• To clean, follow the instructions in the section “15. CLEANING”.

• Cleaning and user maintenance shall not be made by children without supervision.

• Never clean by immersing the appliance in water.

• CAUTION: To prevent damage to the appliance do not use alkaline cleaning agents

when cleaning, use a soft cloth and a mild detergent

• This is a household appliance only. It is not intended to be used in: sta kitchen areas in

shops, oces and other working environments; farm houses; by clients in hotels, motels and other residential type environments; bed and breakfast type environments.

• If the plug or cord is damaged, it must be replaced by Customer Services only to avoid

all risk.

• Appliances with removable cord: avoid splashes of water on the power cord connector

or socket at the back of the appliance.

FOR EUROPEAN MARKETS ONLY:

• This appliance can be used by children aged from 8 years and above if they have been

given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazard involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised.

Keep the appliance and its cord out of the reach of children aged less than 8 years.

•

Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.

• Children shall not play with the appliance.

Page 8

• When not in use and before putting on or taking o parts or cleaning, always unplug

the appliance.

Surfaces marked with this symbol become hot during use (the symbol is present in certain models only).

2. SAFETY WARNINGS

2.1 Symbols used in these instructions

Important warnings are identied by these symbols. It is vital to respect these warnings.

Danger!

Failure to observe the warning may result in life threatening injury by electric shock.

Important!

Failure to observe the warning could result in injury or damage to the appliance.

Danger of burns!

Failure to observe the warning could result in scalds or burns.

Please note:

This symbol identies important advice or information for the user.

Danger!

This is an electrical appliance and may cause electric shock. You should therefore follow these safety warnings:

• Never touch the appliance with damp hands or feet.

• Never touch the plug with damp hands.

• Make sure the socket used is freely accessible at all times,

enabling the appliance to be unplugged when necessary.

• Unplug directly from the plug only. Never pull the cord as

you could damage it.

• To disconnect the appliance completely you must unplug it

from the mains socket.

• If the appliance is faulty, do not attempt to repair.

Turn it o, unplug from the mains socket and contact Cus-

tomer Services.

• Before cleaning the appliance, turn it o, unplug from the

mains socket and allow to cool.

Important:

Keep all packaging (plastic bags, polystyrene foam) away from children.

Danger of burns!

This appliance produces hot water and steam may form while it is in operation. Avoid contact with splashes of water or hot steam. When the appliance is in operation, the cup shelf could become very hot.

2.2 Designated use

This appliance is designed and made to prepare coee and heat beverages. Any other use is considered improper and thus dangerous. The manufacturer is not liable for damage deriving from improper use of the appliance.

2.3 Instruction for Use

Read this Instruction for Use carefully before using the appliance. Failure to follow this Instruction for Use may result in burns or damage to the appliance. The manufacturer is not liable for damage deriving from failure to respect this Instruction for Use.

Please note:

Keep this Instruction for Use. If the appliance is passed to other persons, they must also be provided with this Instruction for Use.

3. INTRODUCTION

Thank you for choosing this bean to cup espresso and cappuccino machine. We hope you enjoy using your new appliance. Take a few minutes to read this Instruction for Use. This will avoid all risks and damage to the appliance.

3.1 Letters in brackets

The letters in brackets refer to the legend in the description of the appliance on pages 2-3.

3.2 Troubleshooting and repairs

In the event of problems, rst try and resolve them by reading the information given in sections “20. Displayed messages” and “21. Troubleshooting”. If this does not resolve the problem or you require further information, you should consult Customer Services by calling the number given on the annexed "Customer Service" sheet. If your country is not among those listed on the sheet, call the number given in the guarantee. If repairs are required, contact De’Longhi Customer Services only. The addresses are given in the guarantee certicate provided with the machine.

Page 9

4. DESCRIPTION

4.1 Description of the appliance

(page 3 - A) A1. Beans container lid A2. Pre-ground coee funnel lid A3. Beans container A4. Pre-ground coee funnel A5. Grinding adjustment dial A6. Cup shelf A7. button: to turn the appliance on and o (standby) A8. Hot water and steam connection nozzle A9. Coee spouts (adjustable height) A10. Condensate tray A11. Coee grounds container A12. Cup tray A13. Drip tray water level indicator A14. Drip tray grille A15. Drip tray A16. Water tank lid A17. Water tank A18. Water softener lter housing A19. Infuser door A20. Infuser A21. Power cord connector socket A22. Main switch

Description of the touch screen

(page 2 - B )

A number of buttons on the panel have a double function. This is indicated in brackets in the description.

B1. Display: guides the user in using the appliance. The current

selection is at the centre between two dotted lines.

B2. ▼ Selection arrow(“ESC”: when programming beverages,

press to exit without saving the change)

B3. OK: to conrm the selection(During the rst few seconds of

"espresso", "R istretto" or "Espresso lungo" delivery, press for 2 cups)

B4. ▲ Selection arrow(“STOP” - When delivering/program-

ming beverages, press to interrupt/programme)

B5. /ESC: to perform a rinse cycle. (When in the settings menu, it acts as the "ESC" button to exit

from the selected function and go back to the main menu)

B6. : appliance settings menu B7. : aroma selection

Directly selected beverages:

B8. : Espresso B9. : Coee B10. : Cappuccino B11. : Latte Macchiato

B12. : Beverage selection menu (other than direct-

ly selected beverages): Espresso lungo, Ristretto, Long, Doppio+, Caelatte, Flat white, Hot milk, 2xEspresso, 2 x Espresso lungo, 2x Ristretto, Hot Water

B13. : My beverages selection menu. Unless previous-

ly programmed from the settings menu (“8.4 Program My beverages”), the beverage is programmed directly the rst time you use the appliance.

4.2 Description of the accessories

(page 2 - C ) C1. Indicator paper C2. Pre-ground coee measure C3. Descaler C4. Water softener lter (certain models only) C5. Cleaning brush C6. Hot water spout C7. Power cord

4.3 Description of the milk container

(page 2 - D ) D1. Froth adjustment and CLEAN dial D2. Milk container lid D3. Milk container D4. Milk intake tube D5. Frothed milk spout (adjustable)

5. BEFORE USE

5.1 Checking the appliance

After removing the packaging, make sure the product is complete and undamaged and that all accessories (C) are present. Do not use the appliance if it is visibly damaged. Contact De’Longhi Customer Services.

5.2 Installing the appliance

Important!

When you install the appliance, you should respect the following safety warnings:

• The appliance gives o heat. After positioning the appliance on the worktop, leave a space of at least 3 cm between the surfaces of the appliance and the side and rear walls and at least 15 cm above the coee maker.

• Water penetrating the coee machine could cause damage.

Do not place the appliance near taps or sinks.

• The appliance could be damaged if the water it contains freezes.

Do not install the appliance in a room where the tempera-

ture could drop below freezing point.

Page 10

• Arrange the cord (C7) in such a way that it cannot be damaged by sharp edges or contact with hot surfaces (e.g. electric hot plates).

5.3 Connecting the appliance

Important!

Check that the mains power supply voltage corresponds to that indicated on the rating plate on the bottom of the appliance. Connect the appliance to an eciently earthed and correctly installed socket with a minimum current rating of 10A only. If the power socket does not match the plug on the appliance, have the socket replaced with a suitable type by a qualied professional.

5.4 Setting up the appliance

Please note:

• Coee has been used to factory test the appliance and it is therefore completely normal for there to be traces of coffee in the mill. The machine is, however, guaranteed to be new.

• You should customise water hardness as soon as possible following the instructions in section “16. Setting water hardness”.

Plug the power cord (C7) connector into the socket (A21) at the back of the appliance and connect the appliance to the mains electricity supply (g. 1). Make sure the main switch (A22) at the back of the appliance is pressed (g. 2);

2. "Language": press the selection arrow (B2) until the required language is displayed between the two dotted lines, then press OK (B3) to conrm.

Then follow the instructions indicated on the appliance display (B1):

3. “Fill tank”: remove the water tank (A17), ll to the MAX line with fresh water (g. 3A), then replace in the appliance (g. 3B);

4. "Insert water spout": Check that the hot water spout (C6) is inserted on the connection nozzle (A8) (g. 4) and place a container holding a minimum of 100 ml underneath (g.

5);

5. "Water circuit empty, Fill water circuit, Hot water, Conrm?";

6. Press the OK button to conrm. The appliance delivers hot water from the spout then goes o automatically.

The coee machine is now ready for normal use.

Please note:

• The rst time you use the coee maker, you need to make 4-5 cups of coee or 4-5 cappuccinos before it starts to give satisfactory results.

• When making the rst 5-6 cappuccinos, it is normal to hear the noise of boiling water. After this, the noise becomes less.

• To enjoy your coee even more and improve the performance of your appliance, we recommend installing a water softener lter (C4) as described in section “17. Water softener lter”. If your model is not provided with a lter, you can request one from De'Longhi Customer Services.

6. TURNING THE APPLIANCE ON

Please note:

Before turning the appliance on, make sure the main switch (A22) on the back of the appliance is pressed (g. 2).

Each time the appliance is turned on, it performs an automatic preheat and rinse cycle which cannot be interrupted. The appliance is ready for use only after completion of this cycle.

Danger of burns!

During rinsing, a little hot water comes out of the coee spouts (A9) and is collected in the drip tray (A15) underneath. Avoid contact with splashes of water.

• To turn the appliance on, press the button (A7) (g.

6). The message "Heating Please wait" appears on the display (B1).

After heating, the message "Rinsing" is displayed, together with a progress bar which gradually lls as preparation proceeds. As well as heating the boiler, the appliance also heats the internal circuits by circulating hot water. The appliance is at temperature when the message "Select your beverage" is displayed.

7. TURNING THE APPLIANCE OFF

Whenever the coee machine is turned o after being used to make coee, it performs an automatic rinse cycle.

Danger of burns!

During rinsing, a little hot water ows from the coee spouts (A9). Avoid contact with splashes of water.

• To turn the appliance o, press the button (A7) (g.

6);

• The message "Turning o underway Please wait" appears on the display (B1), then the appliance performs a rinse cycle and goes o (standby).

Please note!

If you will not be using the appliance for some time, unplug from the mains socket:

Page 11

• rst turn the appliance o by pressing the button (g. 6);

• press the main switch (A22) (g. 2).

Important!

Never press the main switch while the appliance is on.

8. MENU SETTINGS

The menu has 6 items, some divided into subgroups:

• Language;

• Maintenance:

- Descale,

- Install lter,

- (if a lter has been installed): Replace lter,

- (if a lter has been installed): Remove lter;

• Prg. beverages;

• Prg. my beverages;

• General:

- Set temperature,

- Water hardness,

- Auto-o,

- Energy saving,

- Beep,

- Default beverages,

- Default values;

• Statistics.

8.1 Language

To modify the language of the display (B1), proceed as follows:

1. Press (B6) to enter the "Settings" menu;

2. Press OK (B3) to select "Language". The available languages are displayed;

3. Press the selection arrows (B2 and B4) until the required language is displayed between the two lines;

4. Press OK to conrm;

5. The appliance goes back to the "Settings" menu;

6. Press /ESC (B5) to exit the menu.

8.2 Maintenance

Here you can nd all the maintenance operations required by the appliance over time:

• Descale: For instructions on descaling, see section “15. Descaling”.

• Install lter: For instructions on how to install the lter (C4), see section “17.1 Installing the lter”.

To select the operation you require, proceed as follows:

1. Press (B6) to enter the "Settings" menu;

2. Press the selection arrows (B2 and B4) until "Maintenance" is displayed between the two lines;

3. Press OK B3 to conrm;

4. Press the selection arrows to display the operation to be performed;

5. Press OK to conrm and perform the operations as de- scribed in the corresponding sections.

8.3 Program beverages

The appliance is set by default to automatically deliver standard quantities. To change these quantities and customise the directly selected beverages and the (B12), proceed as follows:

1. Press (B6) to enter the "Settings" menu;

2. Press the selection arrows (B2 and B4) until "Prg. beverages" is displayed between the two lines;

3. Press OK (B3) to conrm: the appliance lists the beverages you can customise;

4. Press the selection arrows until the beverage you want to customise is displayed, then press OK to conrm;

5. Beverages with coee: "Program aroma" appears on the display: press the selection arrows (B2 and B4) or (B7) until the required aroma is selected (see section “10.4 Temporarily varying the coee aroma”), then press OK. "Program coee" appears on the display together with a bar which gradually lls as delivery progresses. When the required quantity is reached, press OK;

Cappuccinos and milk-based coees: after selecting

the aroma, "Program milk" appears on the display together with a bar which gradually lls as milk delivery progresses. When the required quantity is reached, press OK. The appliance then makes the coee. Press OK to interrupt delivery when the required quantity of coee is reached.

Hot water: press OK. Delivery begins: press OK when the

required quantity is reached.

6. "Save parameters?": to save the settings, press OK (other- wise press /ESC - B2 or B5).

7. "Parameters saved" (or "Parameters not saved"). The appliance is ready for use again.

8.4 Program My beverages

Follow the procedures described in the previous section “8.3 Program beverages”to customise the beverages in the " " (B13) or proceed with direct programming, as described in section “12. “ ” Programming and selecting”.

8.5 General

Here you can nd the settings to customise the basic functions of the appliance:

1. Press (B6) to enter the "Settings" menu;

2. Press the selection arrows (B2 and B4) until "General" is displayed between the two lines;

Page 12

3. Press OK (B3) to conrm and select the required item with the selection arrows. Then follow the instructions for each setting.

• Set temperature:

To modify the temperature of the water used to make the coee, proceed as follows:

4. Press OK (B3). The current value appears on the display (B1) and the "New" value ashes;

5. Select the new value you want to set using the selection arrows (B2 or B4);

6. When the required value (low, medium, high, maximum) has been selected, press OK.

The display goes back to the previous screen.

• Water hardness:

For instructions on identifying and setting water hardness, see section “16. Setting water hardness”.

• Auto-o (standby):

Auto-o can be set so that the appliance goes o after 15 or 30 minutes, or 1, 2 or 3 hours

4. Press OK. The current value appears on the display (B1) and the "New" value ashes;

5. Select the new value you want to set using the selection arrows (B2 or B4);

6. When the required value (low, medium, high, maximum) has been selected, press OK.

The display goes back to the previous screen.

• Energy saving:

Use this function to enable or disable energy saving. When enabled, the function reduces energy consumption in compliance with European regulations. To disable or enable "Energy Saving", proceed as follows:

4. Press OK. The current state ("Enabled" or "Disabled") and the operation to be performed ("Disable?" or "Enable?") is displayed. Press OK to conrm;

5. Press OK to disable or enable the function.

The display goes back to the previous screen.

Please note!

• when the function is enabled, the symbol "ECO" appears on the display.

• When in energy saving mode, a few seconds elapse before the rst coee, cappuccino or milk-based coee is delivered as the appliance must heat up again.

• If the milk container (D) is inserted, "Energy Saving" cannot be activated.

• Beep:

Use this function to enable or disable the beep. Proceed as follows:

4. Press OK. The current state ("Enabled" or "Disabled") and the operation to be performed ("Disable?" or "Enable?") is displayed. Press OK to conrm;

5. Press OK to disable or enable the function.

The display goes back to the previous screen.

• Default beverages:

Use this function to reset the default values for all the beverages, or the individual beverages programmed previously. Select the beverage, then proceed as follows:

4. Select "All" to reset the aroma and quantity settings to the default values, or select the required beverage, then press OK;

5. "Reset?": to reset the default values, press OK.

6. "Reset complete": the appliance conrms the reset and goes back to the previous screen.

To reset another beverage, repeat from point 4 or to exit, press

/ESC (B5).

• Default values:

Use this function to reset all the appliance and beverage settings (apart from the language which remains as selected the rst time the appliance was used). Select the item, then proceed as follows:

4. "Reset?"; press OK;

5. "Reset complete": the appliance conrms the reset and goes back to the previous screen.

To exit, press /ESC (B5).

8.6 Statistics

This displays statistics relating to the machine. To display the statistics, proceed as follows:

1. Press (B6) to enter the "Settings" menu;

2. Press the selection arrows (B2 and B4) until "Statistics" is displayed between the two lines;

3. Press OK (B3): statistics on the appliance are displayed, use the selection arrows to scroll through the items;

4. Press /ESC (B5) to exit.

To go back to the main screen, press /ESC.

9. RINSING

Use this function to deliver hot water from the coee spouts (A9) and hot water spout (C6), if inserted, to clean and heat the appliance’s internal circuit. Place a container with a minimum capacity of 100ml under the coee and hot water spouts.

Important! Danger of burns.

Do not leave the appliance unattended while hot water is being delivered.

Page 13

1) To enable this function, press (B5). "RINSING" appears on the display (B1);

2) After a few seconds, hot water is delivered rst from the coee spouts, then from the hot water spout (if inserted) to clean and heat the appliance’s internal circuit. A progress bar is displayed and lls gradually as preparation proceeds;

3) To interrupt, press the arrow corresponding to "STOP" (B4).

Please note!

• If the appliance is not used for more than 3-4 days, when switched on again, we strongly recommend performing 2/3 rinses before use;

• After cleaning, it is normal for the coee grounds container (A11) to contain water.

10. MAKING COFFEE

10.1 Adjusting the coee mill

The coee mill is set by default to prepare coee correctly and should not require regulating initially. However, if after making the rst few coees you nd that the coee is either too weak and not creamy enough or delivery is too slow (a drop at a time), this can be corrected by adjusting the grinding dial (A5) (g. 7).

Please note:

The grinding adjustment dial must only be turned when the coee mill is in operation.

If the coee is delivered too slowly or not at all, turn one click clockwise towards 7. For fuller bodied creamier coee, turn one click anticlockwise towards 1 (do not turn more than one click at a time other-

wise the coee could be delivered a drop at a time). These adjustments will only be evident after at least 2 cups of coee have been delivered. If this adjustment does not obtain the desired result, turn the dial another click.

10.2 Tips for a hotter coee

For hotter coee, you should:

• to rinse, press /ESC (B5);

• warm the cups with hot water using the hot water function

(see section “13. Delivering hot water”);

• increase the coee temperature in the "Settings" menu

(see section “8.5 General”).

10.3 Making automatic recipes using coee beans

Important!

Do not use green, caramelised or candied coee beans as they could stick to the coee mill and make it unusable.

1. Fill the container (A3) (g. 8) with coee beans;

2. Place under the coee spouts (A9):

- 1 cup, if you want to make 1 coee (g. 9);

- 2 cups if you want 2 coees.

3. Lower the spouts as near as possible to the cup. This makes

a creamier coee (g. 10);

4. Then select your required coee:

Directly selected beverages

Recipe Quantity Program-

mable quantity

≃ 40 ml from ≃30

Espresso (B8)

≃ 180 ml from ≃100

Coee (B9)

Beverages with coee selectable from the

(B14)

Espresso lungo

Rispresso

Long

Doppio+

2 Espresso

2 Espresso lungo

2 Ristretto

5. Preparation begins. A progress bar appears on the display

(B1) and gradually lls as preparation proceeds.

Please note:

• You can prepare 2 cups of Ristretto, ESPRESSO or Espresso

lungo coee at the same time by pressing "2X" (B3) during preparation of single beverages (the image is displayed for a few seconds at the start of preparation).

≃ 120 ml from ≃80

≃ 30 ml from ≃20

≃ 160 ml from ≃115

≃ 120 ml from ≃80

≃ 40 ml x

2 cups ≃ 120 ml

x 2 cups ≃ 30 ml x

2 cups

to ≃ 80ml

to ≃240ml

to ≃180ml

to ≃40ml

to ≃250ml

to ≃180ml

Default aroma

Page 14

• While the machine is making coee, delivery can be interrupted at any time by pressing the selection arrow corresponding to "STOP" (B4).

• At the end of delivery, to increase the quantity of coee in the cup, just press and hold (within 3 seconds) one of the coee buttons (B8 or B10).

Once the coee has been made, the appliance is ready to make the next beverage.

Please note:

• Various alarm messages could be displayed while using the appliance (ll tank, empty grounds container, etc.). Their meaning is explained in section “20. Displayed messages”.

• For hotter coee, see section “10.2 Tips for a hotter coee”.

• If the coee is delivered a drop at a time, too weak and not creamy enough or too cold, read the tips in section “21. Troubleshooting”.

• To customise the beverages according to personal taste, see sections “8.3 Program beverages” and “8.4 Program My beverages”.

10.4 Temporarily varying the coee aroma

To temporarily vary the aroma of the coee in the automatic recipes, press (B7):

AUTO

Please note:

• The variation in aroma is not saved and the next time a beverage is delivered automatically, the appliance selects the default value (

• If a few seconds elapse between temporary customising of the aroma and delivery of the beverage, the aroma returns to the default value (

Custom (if programmed) / Standard

EXTRA LIGHT

LIGHT

MEDIUM

STRONG

X-STRONG

(see “10.5 Making coee using pre-ground coee”)

AUTO).

10.5 Making coee using pre-ground coee

Important!

• Never add pre-ground coee when the machine is o or it could spread through the inside of the machine and dirty it. This could damage the appliance.

• Never use more than 1 level measure (C2) or it could dirty the inside of the coee machine or block the funnel (A4).

Please note:

If you use pre-ground coee, you can only make one cup of

coee at a time.

1. Press the button (B7) repeatedly until " " appears on the display (B1).

2. Make sure the funnel is not blocked, then add one level measure of pre-ground coee (g. 11).

3. Place a cup under the coee spouts (A9) (g. 9).

4. Then select your required coee:

Directly selected beverages

Recipe Quantity

Espresso (B8)

Coee (B9)

Beverages with coee selectable from the

(B12)

Espresso lungo

Ristretto

Long

5. Preparation begins. The beverage selected appears on the display together with a progress bar which gradually lls as preparation proceeds.

Important! Making LONG coee : Halfway through preparation, the message "Add pre-ground coee" appears on the display (B1). Add one level measure of pre-ground coee and press OK (B3).

Please note:

If "Energy Saving" mode is active, you may have to wait a few seconds before the rst coee is delivered.

≃ 40 ml ≃ 180 ml

≃ 120 ml ≃ 30 ml ≃ 160 ml

11. MAKING CAPPUCCINOS AND MILKBASED

COFFEES

Please note:

• To avoid milk with poor froth or large bubbles, always

clean the milk container lid (D2) and hot water connection nozzle (A8) as described in sections “11.4 Cleaning the milk

Page 15

container after use”, “14.10 Cleaning the milk container” and “14.11 Cleaning the hot water nozzle”.

11.1 Filling and attaching the milk container

1. Remove the lid (D2) (g. 12);

2. Fill the milk container (D3) with a sucient quantity of milk, not exceeding the MAX level marked on the handle (g. 13). Each mark on the side of the container corresponds to 100ml of milk;

Please note:

• For a denser more even froth, you must use skimmed or partially skimmed milk at refrigerator temperature (about 5°C).

• If "Energy Saving" mode is enabled, you may have to wait a few seconds before the rst cappuccino is delivered.

3. Make sure the milk intake tube (D4) is correctly inserted in the bottom of the milk container lid (g. 14);

4. Place the lid back on the milk container;

5. Remove the hot water spout (C6) from the connection nozzle (A8) (g. 15);

6. Attach the container to the connection nozzle and push as far as it will go (g. 16). The machine emits a beep (if enabled);

7. Place a suciently large cup under the coee spouts (A9) and frothed milk spout (D5). Adjust the length of the milk spout. To move it nearer the cup, simply pull it downwards (g. 17);

8. Follow the instructions below for each function.

11.2 Adjusting the amount of froth

Turn the froth adjustment dial (D1) to adjust the amount of froth on the milk delivered while making cappuccinos and milk-based coees.

Dial position

Description Recommended for…

No froth HOT MILK (not frothed) /

CAFFELATTE

Min. froth LATTE MACCHIATO /

FLAT WHITE

Max. froth CAPPUCCINO/ CAPPUCCI

NO+ / ESPRESSO MACCHIA TO / HOT MILK (frothed)

11.3 Making cappuccino and milk-based coees

automatically

1. Fill the milk container (D) and attach it as described above;

2. Select the required beverage:

Directly selected beverages:

• : CAPPUCCINO (B10)

• : Latte Macchiato (B11)

Select by pressing (B12):

• Caelatte

• Flat white

• Hot milk

3. After a few seconds, preparation begins automatically, a progress bar appears on the display and gradually lls as preparation proceeds;

4. After delivering the milk, the machine automatically makes the coee (if required by the recipe).

Please note:

• If you want to interrupt preparation during delivery, press the arrow corresponding to "STOP" (B4).

• Do not leave the milk container out of the refrigerator for long periods. The warmer the milk (5°C is ideal), the poorer the quality of froth produced.

• The beverages can be customised (see sections “8.3 Program beverages” and “8.4 Program My beverages”).

11.4 Cleaning the milk container after use

Important! Danger of burns

• When cleaning the internal tubes of the milk container (D), a little hot water and steam leak out of the milk spout (D5). Avoid contact with splashes of water.

"Set dial to CLEAN, ESC to cancel" appears on the display (B1) each time you use a milk function. Clean as described to eliminate all milk residues (or press “ /ESC” (B5) to clean later):

1. Leave the milk container (D) in the machine (you do not need to empty it);

2. Place a cup or other recipient under the frothed milk spout;

3. Turn the froth adjustment dial (D1) to “CLEAN” (g. 19). “Cleaning underway” appears on the display, together with a progress bar which gradually lls as the operation proceeds. Cleaning stops automatically;

4. Turn the dial back to one of the froth selections;

5. Remove the milk container and always clean the steam connection nozzle (A8) with a sponge (g. 20).

Please note!

• To prepare a number of cappuccinos or milk-based coees, clean the milk container after you have prepared the last beverage only. In this case, press /ESC (B5) to go back to the main menu.

• The milk container can be kept in the refrigerator.

• In some cases, before cleaning you must wait for the appliance to heat up.

Page 16

12. “ ” PROGRAMMING AND SELECTING

In you can select beverages customised to your personal tastes. If the beverages have not yet been programmed, the appliance will request the customisation procedure before proceeding with delivery:

1. Press (B13);

2. Press the selection arrows (B2 and B4) until the required beverage is displayed between the two lines;

Unprogrammed beverages:

3. Press OK (B3) to select;

4. Beverages with coee: "Program aroma" appears on the display. Press the selection arrows (B2 and B4) or

(B7) until the required aroma is selected. Press OK. "Program coee" appears on the display together with a bar which gradually lls as delivery progresses. When the required quantity is reached, press OK.

5. Cappuccinos and milk-based coees: After selecting the aroma, "Program milk" appears on the display together with a bar which gradually lls as milk delivery progresses. When the required quantity is reached, press OK.

6. The appliance then makes the coee. Press OK to interrupt delivery when the required quantity of coee is reached.

7. "Save parameters?": to save the settings, press OK (other- wise press ESC - B2 or B5).

8. "Parameters saved" (or "Parameters not saved"). The appliance is ready for use again.

Programmed beverages:

3. Press OK (B3) to select;

4. Preparation begins according to the previously programmed settings.

Please note:

Two cups of a beverage can only be selected when the corresponding single beverages have been programmed.

13. DELIVERING HOT WATER

Important! Danger of burns.

Never leave the machine unattended while delivering hot water.

1. Make sure the hot water spout (C6) is attached correctly;

2. Place a container under the water spout (as close as possible to avoid splashes) (g. 5);

3. Press (B12) and scroll through the beverages in the menu by pressing the selection arrows (B2 or B4) until "Hot water" is selected;

4. Press OK (B3). A progress bar appears and gradually lls as preparation proceeds;

5. The machine delivers about 250 ml of hot water, then delivery stops automatically. To interrupt hot water deliv-

ery manually, press the selection arrow corresponding to "STOP" (B4) again.

Please note:

• If "Energy Saving" mode is active, you may have to wait a few seconds before hot water is delivered.

• The quantity of water delivered can be customised (see section “8.3 Program beverages”).

14. CLEANING

14.1 Cleaning the machine

The following parts of the machine must be cleaned regularly:

- the appliance’s internal circuit;

- coee grounds container (A11);

- drip tray (A15) and condensate tray (A10);

- water tank (A17);

- coee spouts (A9);

- pre-ground coee funnel (A4);

- infuser (A20), accessible after opening the infuser door (A19);

- milk container (D);

- hot water/steam connection nozzle (A8);

Important!

• Do not use solvents, abrasive detergents or alcohol to clean the coee machine. With De’Longhi superautomatic coee machines, you need not use chemical products to clean the machine.

• None of the components of the appliance can be washed in a dishwasher with the exception of the drip tray grille (A14) and milk container (D).

• Do not use metal objects to remove encrustations or coee deposits as they could scratch metal or plastic surfaces.

14.2 Cleaning the machine's internal circuit

If the appliance is not used for more than 3/4 days, before using it again, we strongly recommend switching it on and:

- performing 2/3 rinse cycles by pressing (B5);

- delivering hot water for a few seconds (section “13. Delivering hot water”).

Please note:

After cleaning, it is normal for the coee grounds container (A11) to contain water.

14.3 Cleaning the coee grounds container

When "Empty grounds container" appears on the display (B1), the grounds container must be emptied and cleaned. The appliance cannot be used to make coee until you have cleaned the grounds container (A11). Even if not full, the empty grounds container message appears on the display 72 hours after the

Page 17

rst coee has been prepared. For the 72 hours to be calculated correctly, the machine must never be turned o with the main switch (A22).

Important! Danger of burns

If you make a number of cappuccinos one after the other, the metal cup tray (A12) becomes hot. Wait for it to cool down before touching it and handle it from the front only.

To clean (with the machine on):

• Remove the drip tray (A15) (g. 21), empty and clean.

• Empty the grounds container (A11) and clean thoroughly to remove all residues left on the bottom. This can be done with the spatula on the brush (C5) provided.

• Check the condensate tray (A10) (red) and empty if necessary.

Important!

When removing the drip tray, the grounds container must be emptied, even if it contains few grounds. If this is not done, when you make the next coees, the grounds container may ll up more than expected and clog the machine.

14.4 Cleaning the drip tray and condensate tray

Important!

The drip tray (A15) is tted with a level indicator (A13) (red) showing the level of water it contains (g. 22). Before the indicator protrudes from the cup tray (A12), the drip tray must be emptied and cleaned otherwise the water may overow the edge and damage the appliance, the surface it rests on or the surrounding area. To remove the drip tray:

1. Remove the drip tray and the coee grounds container (A11) (g. 21);

2. Remove the cup tray (A12) and drip tray grille (A14), then empty the drip tray and grounds container and wash all components;

3. Check the red condensate tray (A10) and empty if necessary;

4. Replace the drip tray complete with grille and grounds container.

14.5 Cleaning the inside of the coee machine

Danger of electric shock!

Before cleaning internal parts, the machine must be turned o (see section “7. Turning the appliance o”) and unplugged from the mains power supply. Never immerse the coee machine in water.

1. Check regularly (about once a month) that the inside of the appliance (accessible after removing the drip tray, A15) is not dirty. If necessary, remove coee deposits with the brush (C5) supplied and a sponge;

2. Remove all the residues with a vacuum cleaner (g. 23).

14.6 Cleaning the water tank

1. Clean the water tank (A17) regularly (about once a month) and whenever you replace the water softener lter (C4) (if provided) with a damp cloth and a little mild washing up liquid;

2. Remove the lter (C4) (if present) and rinse with running water;

3. Replace the lter (if provided), ll the tank with fresh water and replace the tank;

4. (Models with water softener lter only) Deliver about 100ml of water.

14.7 Cleaning the coee spouts

1. Clean the coee spouts (A9) regularly with a sponge or cloth (g. 24A);

2. Check that the holes in the coee spouts are not blocked. If necessary, remove coee deposits with a toothpick (g. 24B).

14.8 Cleaning the pre-ground coee funnel

Check regularly (about once a month) that the pre-ground coee funnel (A4) is not blocked. If necessary, remove coee deposits with the brush (C5) supplied.

14.9 Cleaning the infuser

The infuser (A20) must be cleaned at least once a month.

Important!

The infuser may not be extracted when the machine is on.

1. Make sure the machine is correctly turned o (see “7. Turning the appliance o”);

2. Remove the water tank (A17);

3. Open the infuser door (A19) (g. 25) on the right side of the appliance;

4. Press the two coloured release buttons inwards and at the same time pull the infuser outwards (g. 26);

5. Soak the infuser in water for about 5 minutes, then rinse under the tap;

Important!

RINSE WITH WATER ONLY NO WASHING UP LIQUID  NO DISH WASHER Clean the infuser without using washing up liquid as it

could be damaged.

Page 18

6. Use the brush (C5) to remove any coee residues left in the infuser housing, visible through the infuser door;

7. After cleaning, replace the infuser by sliding it onto the internal support, then push the PUSH symbol fully in until it clicks into place;

Please note:

If the infuser is dicult to insert, before insertion, adapt it to the right size by pressing the two levers (g. 27).

8. Once inserted, make sure the two coloured buttons have snapped out;

9. Close the infuser door;

10. Put the water tank back.

14.10 Cleaning the milk container

Clean the milk container (D) each time you prepare milk as described below:

1. Remove the lid (D2);

2. Remove the milk spout (D5) and intake tube (D4) (g. 28);

3. Turn the froth adjustment dial (D1) anticlockwise to the "INSERT" position (g. 29) and pull o upwards;

4. Wash all the components thoroughly with hot water and mild washing-up liquid. All components are dishwasher safe, placing them in the top basket of the dishwasher.

Make sure there are no milk residues on the hollow and

groove under the dial (g. 30). If necessary, scrape the groove with a toothpick;

5. Rinse inside the froth adjustment dial seat with running water (g. 31);

6. Check that the intake tube and milk spout are not clogged with milk residues;

7. Replace the dial (in correspondence to the word "INSERT"), spout and milk intake tube;

8. Place the lid back on the milk container (D3).

14.11 Cleaning the hot water nozzle

Each time you prepare milk, clean the connection nozzle (A8) with a sponge to remove milk residues from the gaskets (g.

20).

15. DESCALING

Important!

• Before use, read the instructions and the labelling on the descaler pack.

• You should use De’Longhi descaler only. Using unsuitable descaler and/or performing descaling incorrectly may result in faults not covered by the manufacturer's guarantee.

Descale the machine when "Descale, ESC to cancel, OK to descale (∼45 minutes)" appears on the display (B1). To descale immediately, press OK (B3) and follow the instructions from point

6. To descale the appliance later, press ESC (B5). The symbol on the display reminds you that the appliance needs descaling. To access the descaling menu:

1. Turn the appliance on and wait until it is ready for use;

2. Press (B6) to enter the "Settings" menu;

3. Press the selection arrows (B2 and B4) until "Maintenance" is displayed between the two lines. Press OK (B3);

4. Press OK to select "Descale";

5. Conrm? (∼45 minutes)”. Press OK to conrm;

6. "Remove lter": extract the water tank (A17), remove the water softener lter (C4) (if present) and empty the water tank. Press OK;

7. "Pour descaler and water into tank": Pour the descaler into the tank up to level A (corresponding to a 100 ml pack) marked on the inner surface of the tank, then add water (1 litre) up to level B (g. 32) and put the water tank back. Press OK;

8. "Empty drip tray": Remove, empty and replace the drip tray (A15) and grounds container (A11). Press OK;

"Place 1.8L container empty under spouts": Place an empty container with a minimum capacity of 1.8 litres under the hot water spout (C6) and coee spouts (A9) (g. 33). Press OK

Important! Danger

of burns

Hot water containing acid ows out of the coee spouts and hot water spout. Take care to avoid contact with splashes of this solution.

10.

"Descaling underway":

1,8 l

water and coee spouts. A series of rinses and pauses is performed automatically to remove all the scale residues inside the coee machine;

After about 25 minutes, descaling stops;

11. "Rinse tank and ll with water": the appliance is now ready to rinse with fresh water. Empty the container used to collect the descaler solution. Extract the water tank, empty, rinse under running water, ll with fresh water up to the MAX level and put back in the appliance. Press OK;

12. "Place 1.8L container empty under spouts": place the container used to collect the descaler solution empty under the coee spouts and hot water spout (g. 33) and press OK";

13. "Rinsing Conrm?": press OK;

The descale programme starts and the descaler liquid comes out of the hot

;

Page 19

11. "Rinsing underway": hot water is delivered rst from the coee spouts, then from the hot water spout;

12. When the water in the tank has run out, empty the container used to collect the rinsing water;

13. "Rinse tank and ll with water": extract the water tank and ll with fresh water up to the MAX level. Press OK;

14. "Insert lter": put the water softener lter (if removed) back in its housing in the water tank, and replace the tank in the appliance. Press OK;

15. "Place 1.8L container empty under spouts": tainer used to collect the descaler solution empty under the hot water spout. Press OK;

16. "Rinsing Conrm?": press OK.

17. "Rinsing underway". spout;

18. "Empty drip tray": At the end of the second rinse, remove, empty and replace the drip tray (A15) and grounds container (A11). Press OK;

19. "Descale complete": press OK;

20. "Fill tank": empty the container used to collect the rinse water, remove the water tank and ll with fresh water up to the MAX level, then put back in the appliance.

Descaling is complete.

Please note!

• If the descaling cycle is not completed correctly (e.g. no electricity) we recommend repeating the cycle;

• After descaling, it is normal for the grounds container (A11) to contain water;

• If the water tank has not been lled to the MAX level, at the end of descaling, the appliance requests a third rinse to guarantee that the descaler solution has been completely eliminated from the machine's internal circuits.

• The appliance may request descaling cycles at very short intervals. This is normal and due to the appliance’s advanced control system.

Hot water comes out of the hot water

place the con-

16. SETTING WATER HARDNESS

The descale message is displayed after a period of time established according to water hardness. The machine is set by default for a hardness level of 4. The machine can also be programmed according to the hardness of the mains water in the various regions so that the machine needs to be descaled less often.

16.1 Measuring water hardness

1. Remove the "TOTAL HARDNESS TEST" indicator paper (C1) from its pack (attached to the English instructions);

2. Immerse the paper completely in a glass of water for one second;

3. Remove the paper from the water and shake lightly. After about a minute, 1, 2, 3, or 4 red squares form, depending on the hardness of the water. Each square corresponds to one level;

soft water (level 1)

slightly hard water (level 2)

hard water (level 3)

very hard water (level 4)

16.2 Setting water hardness

1. Press (B6) to enter the "Settings" menu;

2. Press the selection arrows (B2 and B4) until "General" is displayed between the two lines. Press OK;

3. Press the selection arrows until "Water hardness" is displayed, then press OK;

4. The current selection appears on the display and the new selection ashes. Press the selection arrows until the required new selection is displayed. Press OK.

The new level is saved and the appliance goes back to the "General" menu. Press /ESC (B5) twice to go back to the main screen.

17. WATER SOFTENER FILTER

Certain models are tted with a water softener lter (C4). If this is not the case with your model, you are recommended to purchase one from De’Longhi Customer Services. To use the lter correctly, follow the instructions below.

17.1 Installing the lter

1. Remove the lter (C4) from the packaging. The date indicator disk varies according to the lter provided.

2. Turn the date indicator

disk (g. 34) until the next 2 months of use are displayed.

Please note

The lter lasts about two months if the appliance is used normally.

Page 20

If the coee machine is left unused with the lter installed, it will last a maximum of three weeks.

3. To activate the lter, run tap water through the hole in the lter as shown in g. 35 until water comes out of the openings at the side for more than a minute.;

13. The appliance begins hot water delivery and the message "Please wait" is displayed;

14. After the ow of hot water stops, the appliance automatically resets to "Ready for coee" status.

The lter is now active and you can use the coee machine.

0,5 L

35 36

4. Extract the tank (A17) from the appliance and ll with water;

5. Insert the lter in the water tank and immerse it completely for about ten seconds, sloping it and pressing it lightly to enable the air bubbles to escape (g. 36).

6. Insert the lter in the lter housing (A18) and press as far as it will go (g. 37);

7. Close the tank with the lid (A16) (g. 38), then replace the tank in the machine;

17.2 Replacing the lter

Replace the lter (C4) when "Replace lter, ESC to cancel, OK to replace" appears on the display (B1). To replace immediately, press OK (B3) and follow the instructions from point 8. To replace later, press ESC (B5). The symbol on the display reminds you that the lter needs replacing. To replace the lter, proceed as follows:

1. Extract the tank (A17) and exhausted lter;

2. Take the new lter out of its packet and proceed as illustrated in points 2, 3, 4, 5, 6 and 7 in the previous section;

3. Press (B6) to enter the "Settings" menu;

4. Press the selection arrows (B2 and B4) until "Maintenance" is displayed between the two lines. Press OK;

5. Press the selection arrows until "Replace lter" is displayed, then press OK;

6. Conrm?": press OK;

7. "Hot water, Conrm?": Position a container under the hot water spout (C6) (min. capacity: 500 ml), then press OK;

8. The appliance begins hot water delivery and the message "Please wait" is displayed;

9. After the ow of hot water stops, the appliance automatically resets to "Ready for coee" status.

The new lter is now active and you can use the coee machine.

Please note!

After two months (see date indicator) or when the appliance has not been used for 3 weeks, you should replace the lter even if the message has not yet been displayed.

37 38

When you install the lter, you must notify the appliance of its presence.

8. Press (B6) to enter the "Settings" menu;

9. Press the selection arrows (B2 and B4) until "Maintenance" is displayed between the two lines. Press OK;

10. Press the selection arrows until "Install lter" is displayed, then press OK;

11. Conrm?": press OK;

12. "Hot water, Conrm?": Position a container under the hot water spout (C6) (min. capacity: 500 ml), then press OK;

17.3 Removing the lter

If you want to use the appliance without the lter (C4), you must remove it and notify the appliance of its removal. Proceed as follows:

1. Extract the tank (A17) and exhausted lter;

2. Press (B6) to enter the "Settings" menu;

3. Press the selection arrows (B2 and B4) until "Maintenance" is displayed between the two lines. Press OK;

4. Press the selection arrows until "Remove lter" is displayed, then press OK;

5. "Conrm?": press OK to conrm removal. The appliance goes back to the "Maintenance" menu;

Press /ESC (B5) to exit the menu.

Page 21

Please note!

After two months (see date indicator) or when the appliance has not been used for 3 weeks, you should replace the lter even if the message has not yet been displayed.

18. TECHNICAL DATA

Voltage: 220-240 V~ 50/60 Hz max. 10A Absorbed power: 1450W

This product complies with European regulation no. 1935/2004 on materials and articles intended to come into contact with food.

19. DISPOSING OF THE APPLIANCE

The appliance must not be disposed of with household waste, but taken to an authorised waste separation and recycling centre.

Pressure: 1.5MPa (15 bars) Max. water tank capacity: 1.8 l Size LxDxH: 240x440x360 mm Cord length: 1750 mm Weight: 9.9 kg Max. beans container capacity: 300 g

20. DISPLAYED MESSAGES

DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY

Fill tank Insucient water in the tank (A17). Fill the tank with water and/or insert it correct-

ly, pushing it as far as it will go until it clicks into place (g. 3B).

Insert tank The tank (A17) is not correctly in place. Insert the tank correctly and press as far as it

will go (page 3B).

Empty grounds container The grounds container (A11) is full. Empty the grounds container and drip tray

(A15), clean and replace. Important: when removing the drip tray, the grounds container MUST be emptied, even if it contains few grounds. If this is not done, when you make the next coees, the grounds container may ll up more than expected and clog the machine.

Insert grounds container After cleaning, the grounds container (A11)

has not been replaced.

Add pre-ground coee The "pre-ground coee" function has been se-

lected without placing any pre-ground coee in the funnel (A4).

A LONG coee with pre-ground coee has been requested

Fill beans container The coee beans have run out. Fill the beans container (A3) (g. 8).

Remove the drip tray (A15) and insert the grounds container.

Place pre-ground coee in the funnel (g. 11) or deselect the "pre-ground" function.

Put one level measure of pre-ground coffee into the pre-ground coee funnel (A4) and press OK (B3) to continue and complete preparation.

The pre-ground coee funnel (A4) is clogged. Empty the funnel with the help of the brush

(C5) as described in section “14.8 Cleaning the pre-ground coee funnel”.

Page 22

Ground too ne Adjust mill

Less coee Too much coee has been used.

Insert water spout The hot water spout (C6) is not inserted or is

Insert milk container The milk container (D) is not inserted correctly. Inser t the milk container as far as it will go (g.

Insert infuser assembly The infuser (A20) has not been replaced after

Water circuit empty Fill water circuit Hot water Conrm?

Press OK to CLEAN The milk container (D) has been inserted with

Set dial to CLEAN ESC to cancel

Turn froth adjustment dial The milk container (D) has been inserted with

Descale ESC to cancel OK to descale (∼45 minutes)

Replace lter ESC to cancel OK to replace

General alarm The inside of the appliance is very dirty. Clean the inside of the appliance thoroughly,

The grinding is too ne and the coee is delivered too slowly or not at all.

If the water softener lter (C4) is present, an air bubble may have been released inside the circuit, obstructing delivery.

inserted incorrectly.

cleaning.

The water circuit is empty. Press OK (B3) to deliver water from the spout

the froth adjustment dial (D1) in the "CLEAN" position.

Milk has been delivered recently and the tubes inside the milk container (D) must be cleaned.

the froth adjustment dial (D1) in the "CLEAN" position.

The machine must be descaled. The descaling procedure described in section

The water softener lter (C4) is exhausted. Replace the lter or remove it as described in

Repeat coee delivery and turn the grinding adjustment dial (A5) (g. 7) one click clockwise towards 7 while the coee mill is in operation. If after making at least 2 coees delivery is still too slow, repeat the correction procedure, turning the grinding adjustment dial another click until delivery is correct (see section “10.1 Adjusting the coee mill”. If the problem persists, make sure the water tank (A17) is fully inserted.

Insert the hot water spout (C6) in the appliance and deliver a little water until the ow becomes regular.

Select a lighter taste by pressing (B7) or reduce the quantity of pre-ground coee.

Fully insert the hot water spout (g. 4).

16).

Insert the infuser as described in section “14.9 Cleaning the infuser”.

(C6) until it ows out normally. If the problem persists, make sure the water tank (A17) is fully inserted.

To proceed with the CLEAN function press OK or turn the froth adjustment dial to another position.

Turn the froth adjustment dial (D1) to CLEAN (g. 19).

Turn the froth adjustment dial to one of the milk froth positions.

“15. Descaling” needs to be performed.

section “17. Water softener lter”.

as described in section “14. Cleaning”. If the message is still displayed after cleaning, contact a service centre.

Page 23

ECO

The tubes inside the milk container (D) must be cleaned.

The water softener lter (C4) is exhausted and must be replaced or removed.

The machine must be descaled. The descaling procedure described in section

Energy saving is enabled. To disable energy saving, proceed as described

Turn the froth adjustment dial (D1) to CLEAN (g. 19)

Replace the lter or remove it as described in section “17. Water softener lter”.

“15. Descaling” needs to be performed. The appliance may request descaling cycles at very short intervals. This is normal and due to the appliance’s advanced control system.

in section “8.5 General” - “•Energy saving:”

Page 24

21. TROUBLESHOOTING

Below is a list of some of the possible malfunctions. If the problem cannot be resolved as described, contact Customer Services.

PROBLEM POSSIBLE CAUSE REMEDY

The coee is not hot. The cups were not preheated. Warm the cups by rinsing them with hot

water (Please note: you can use the hot water function).

The internal circuits of the appliance have cooled down because 2/3 minutes have elapsed since the last coee was made.

A low coee temperature is set. Set a higher coee temperature in the menu.

Before making coee, rinse the internal circuits by pressing the button (B5).

The coee is weak or not creamy enough.

The coee is delivered too slowly or a drop at a time.

The appliance will not make coee

Coee does not come out of one or both of the spouts.

The appliance does not come onIt is not plugged into the mains socket. Plug into the mains socket (g. 1).

The infuser cannot be extracted

The coee is ground too coarsely. Turn the grinding adjustment dial (A5) one

click anticlockwise towards 1 while the coee mill is in operation (g. 7). Continue one click at a time until coee delivery is satisfactory. The eect is only visible after delivering 2 coees (see section “10.1 Adjusting the coee mill”).

The coee is unsuitable. Use pre-ground coee for espresso machines.

The coee is ground too nely. Turn the grinding adjustment dial (A5) one

click clockwise towards 7 while the coee mill is in operation (g. 7). Continue one click at a time until coee delivery is satisfactory. The eect is only visible after delivering 2 coees (see sec tion “10.1 Adjusting the coee mill”).

The appliance has detected impurities in its internal circuits. "Please wait" is displayed.

The coee spouts (A9) are blocked. Clean the spouts with a toothpick (g. 24B).

The main switch (A22) is not turned on. Place the main switch in the I position (g. 2).

The power cord (C7) connector is not inserted correctly.

The appliance has not been turned o correctly

Wait for the appliance to be ready for use again and reselect the required beverage. Contact Customer Services if the problem persists.

Insert the connector as far as it will go in the socket at the back of the appliance (g. 1).

Turn the appliance o by pressing the button (A7) g. 6) (see section “7. Turning the appliance o”).

Page 25

At the end of descaling, the appliance requests a third rinse

The milk does not come out of the milk spout (D5)

The milk contains large bubbles and squirts out of the milk spout (D5) or there is little froth

During the two rinse cycles, the water tank has not been lled to the MAX level.

The lid (D2) of the milk container lid is dirty Clean the milk container lid as described in the

The milk is not cold enough or is not semi-skimmed.

The froth adjustment dial (D1) is incorrectly adjusted.

The milk container lid (D2) or froth adjustment dial (D1) is dirty

The hot water connection nozzle (A8) is dirty Clean the connection nozzle as described in

Follow the instructions displayed by the appliance, but rst empty the drip tray to avoid the water overowing.

section “15. Descaling”.

Use skimmed or semi-skimmed milk at refrigerator temperature (about 5° C). If the result is not as you wished, try changing brand of milk.

Adjust following the instructions in section “

• Espresso macchiato;”.

Clean the milk container lid and dial as described in section “15. Descaling”.

section . “14.11 Cleaning the hot water nozzle”.

Page 26

22. ELECTRICAL REQUIREMENTS

Before using this appliance ensure that the voltage indicated on the product corresponds with the main voltage in your home, if you are in any doubt about your supply contact your local electricity company. The exible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 13 amp capacity. Should this plug not t the socket outlets in your home, it should be cut o and replaced with a suitable plug, following the procedure outlined below. Note: Such a plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might nd it and plug it into a supply socket - with the obvious consequent danger. Please note: We recommend the use of good quality plugs and wall sockets that can be switched o when the machine is not in use. IMPORTANT: The wires in the mains lead tted to this appliance are coloured in accordance with the following code:

Green and Yellow to Earth

GREEN AND YELLOW EARTH BLUE NEUTRAL BROWN LIVE

Blue to neutral

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

- The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow.

- The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

- The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. If your electricity supply point has only two pin socket outlets, or if you are in doubt, consult a qualied electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualied electrician and should only be replaced with a exible cord of the same size. After replacement of a fuse in the plug, the fuse cover must be retted. If the fuse cover is lost, the plug must not be used until a replacement cover is obtained. The colour of the correct replacement fuse cover is that of the coloured insert in the base of the fuse recess or elsewhere on the plug. Always state this colour when ordering a replacement fuse cover. Only 13amp replacement fuses which are asta approved to B.S. 1362 should be tted. This appliance conforms to the Norms EN 55014 regarding the suppression of radio interference.

Warning - this appliance must be earthed

13 amp Fuse

Brown to live

Cord Clamp