Wash FX 2
Quick Reference Guide
QUICK REFERENCE GUIDE
EN
The Wash FX2 Quick Reference Guide (QRG) has basic product information such as mounting, menu options, and DMX values. Download the User Manual from www.chauvetdj.com for more details.
The information and specifications contained in this QRG are subject to change without notice.
These Safety Notes include important information about installation, use, and maintenance.
·Always connect the product to a grounded circuit.
·Make sure the power cord is not crimped or damaged.
·Always disconnect the product from the power source before cleaning it or replacing the fuse.
·Never disconnect the product from the power source by pulling or tugging on the cord.
·If mounting the product overhead, make sure there is adequate support for the product’s weight and always secure the product using a safety cable.
·Make sure there are no flammable materials close to the product when it is operating.
·Avoid direct eye exposure to the light source while the product is on.
·Do not touch the product’s housing when the product is operating because the housing can be very hot.
·The product is not intended for permanent installation.
·The product is for indoor use only. It is rated at IP20.
·Do not expose the product to rain or moisture.
·Always connect the product to a power source that is within the voltage range stated on the label or rear panel of the product.
·Never connect the product to a dimmer or rheostat.
·Make sure to replace the fuse with another of the same type and rating.
·Always install the product in a location with adequate ventilation.
·Always leave at least 20 in (50 cm) between the product and adjacent surfaces.
·Be sure that no ventilation slots on the product’s housing are blocked.
·Do not operate the product at an ambient temperature higher than 104 °F (40 °C).
·Never carry the product by the power cord or any moving part.
·Always use the mounting/hanging bracket to lift the product.
·If there is a serious operating problem, stop using the product immediately.
·Never try to repair the product. Repairs carried out by untrained people can lead to damage or malfunction.
·To eliminate wear and improve its lifespan, during periods of non-use completely disconnect from power via breaker or by unplugging it.
Outside the U.S., United Kingdom, Benelux, France, Germany, Ireland, Mexico, or Benelux, contact your distributor to request support or return a product. Visit www.chauvetdj.com for contact information.
•Wash FX2
•Power Cord
•Warranty Card
•Quick Reference Guide
Unpack your Wash FX2 and make sure you have received all parts in good condition. If the box or contents appear damaged, notify the carrier immediately, not Chauvet.
1 |
Wash FX2 QRG Rev. 2 |
QUICK REFERENCE GUIDE
EN
This product has an auto-ranging power supply that works with an input voltage range of 100 to 240 VAC, 50/60 Hz.
To eliminate wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
For the maximum number of Wash FX2 products that you can power link at each voltage, see the User Manual or the specification sticker on the product.
1.Disconnect the product from power.
2.Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
3.Pry the safety cap out of the housing.
4.Remove the blown fuse from the clip on the front of the safety cap and replace with a fuse of the exact same type and rating.
5.Re-insert the fuse holder and reconnect power.
Before mounting this product, read the Safety Notes.
Mounting Clamp
(such as CLP-15 from Chauvet)
Mounting Bracket |
Safety Cable |
(such as CH-05 from |
|
(Included) |
Chauvet) |
Wash FX2 QRG Rev. 2 |
2 |
QUICK REFERENCE GUIDE
EN
BUTTON FUNCTION
<MENU> Exits from the current menu or function
<UP> Navigates upwards through the menu list and increases the numeric value when in a function <DOWN> Navigates downwards through the menu list and decreases the numeric value when in a function
<ENTER> Enables the currently displayed menu or sets the currently selected value into the selected function
MODE |
PROGRAMMING LEVELS |
DESCRIPTION |
|||
DMX Mode |
3Ch |
|
d001-512 |
|
|
|
|
Sets the DMX personality |
|||
8Ch |
|
||||
|
28Ch |
|
|
|
|
Static Colors |
C-- |
C001 |
-022 |
Static colors |
|
Auto Programs |
P-- |
P 1-16 |
Auto programs |
||
Auto Speed |
S-- |
S001-100 |
Program speed for P1~P16 |
||
Dimmer |
dIM |
L001-255 |
Adjust the dimmer on auto and sound |
||
programs |
|||||
|
|
|
|
||
Sound-Active |
Snd |
Snd1-9 |
Sound-active programs |
||
Mode |
|||||
|
|
|
|
||
Sound |
SEnS |
u001-100 |
Sound sensitivity |
||
Sensitivity |
|||||
|
|
|
|
||
|
|
r000-255 |
|
||
Custom Color |
u-- |
g000-255 |
Custom static colors |
||
Mixing |
|
|
Combines Red, Green, Blue, and UV |
||
b000-255 |
|||||
|
|||||
|
|
u000-255 |
|
||
Infrared Mode |
SEt |
on |
Turns infrared on or off |
||
oFF |
|||||
|
|
|
3 |
Wash FX2 QRG Rev. 2 |
QUICK REFERENCE GUIDE
EN
The Wash FX2 can work with a DMX controller. Instructions for connecting and configuring this product for DMX operation are in the User Manual. If you are not familiar with DMX, download the DMX Primer from www.chauvetdj.com.
To ensure full access to all channels available in each DMX mode, the highest recommended DMX address is 484.
The Wash FX2 uses the DMX data connection for its Master/Slave mode. Information about configuring the Wash FX2 for Master/Slave operation is in the User Manual, which is available from the Chauvet website.
The Wash FX2 can be operated with the CHAUVET IRC-6. For more information about the IRC-6, download instructions for the IRC-6 or the Wash FX2 User Manual from www.chauvetdj.com.
28Ch
CHANNEL |
FUNCTION |
VALUE |
PERCENT/SETTING |
||
|
|
000 005 |
No function |
|
|
|
|
006 020 |
Program 1 |
|
|
|
|
021 035 |
Program 2 |
|
|
|
|
036 050 |
Program 3 |
|
|
|
|
051 065 |
Program 4 |
|
|
|
|
066 080 |
Program 5 |
|
|
|
|
081 095 |
Program 6 |
|
|
1 |
Auto Program |
096 110 |
Program 7 |
|
|
111 125 |
Program 8 |
|
|||
|
|
126 140 |
Program 9 |
|
|
|
|
141 155 |
Program 10 |
|
|
|
|
156 170 |
Program 11 |
|
|
|
|
171 185 |
Program 12 |
|
|
|
|
186 200 |
Program 13 |
|
|
|
|
201 215 |
Program 14 |
|
|
|
|
216 230 |
Program 15 |
|
|
|
|
231 255 |
Program 16 |
|
|
2 |
Auto program Speed |
000 250 |
Speed, slow to fast |
|
|
251 255 |
Sound Active Mode |
||||
|
|
||||
3 |
Dimmer |
000 255 |
Adjust the dimmer on auto and sound programs |
|
|
4 |
Strobe |
000 255 |
0-20 Hz, slow to fast |
|
|
5 |
Red Zone 1 |
000 255 |
0–100% |
|
|
6 |
Green Zone 1 |
000 255 |
0–100% |
|
|
7 |
Blue Zone 1 |
000 255 |
0–100% |
|
|
8 |
UV Zone 1 |
000 255 |
0–100% |
|
|
9 |
Red Zone 2 |
000 255 |
0–100% |
|
|
10 |
Green Zone 2 |
000 255 |
0–100% |
|
|
11 |
Blue Zone 2 |
000 255 |
0–100% |
|
|
12 |
UV Zone 2 |
000 255 |
0–100% |
|
|
13 |
Red Zone 3 |
000 255 |
0–100% |
|
|
14 |
Green Zone 3 |
000 255 |
0–100% |
|
|
15 |
Blue Zone 3 |
000 255 |
0–100% |
|
|
16 |
UV Zone 3 |
000 255 |
0–100% |
|
|
17 |
Red Zone 4 |
000 255 |
0–100% |
|
|
18 |
Green Zone 4 |
000 255 |
0–100% |
|
|
|
|
|
|
|
|
Wash FX2 QRG Rev. 2 |
|
4 |
QUICK REFERENCE GUIDE
EN
CHANNEL |
FUNCTION |
VALUE |
PERCENT/SETTING |
||
19 |
Blue Zone 4 |
000 255 |
0–100% |
|
|
20 |
UV Zone 4 |
000 255 |
0–100% |
|
|
21 |
Red Zone 5 |
000 255 |
0–100% |
|
|
22 |
Green Zone 5 |
000 255 |
0–100% |
|
|
23 |
Blue Zone 5 |
000 255 |
0–100% |
|
|
24 |
UV Zone 5 |
000 255 |
0–100% |
|
|
25 |
Red Zone 6 |
000 255 |
0–100% |
|
|
26 |
Green Zone 6 |
000 255 |
0–100% |
|
|
27 |
Blue Zone 6 |
000 255 |
0–100% |
|
|
28 |
UV Zone 6 |
000 255 |
0–100% |
|
|
8Ch |
|
|
|
|
|
|
|
|
|
|
|
CHANNEL |
FUNCTION |
VALUE |
PERCENT/SETTING |
||
|
|
|
|
|
|
1 |
Red |
000 255 |
0–100% |
||
2 |
Green |
000 255 |
0–100% |
||
3 |
Blue |
000 255 |
0–100% |
||
4 |
UV |
000 255 |
0–100% |
||
5 |
Strobe |
000 255 |
0-20 Hz, slow to fast |
||
|
|
000 005 |
No function |
||
|
|
006 020 |
Program 1 |
||
|
|
021 035 |
Program 2 |
||
|
|
036 050 |
Program 3 |
||
|
|
051 065 |
Program 4 |
||
|
|
066 080 |
Program 5 |
||
|
|
081 095 |
Program 6 |
||
6 |
Auto Program |
096 110 |
Program 7 |
||
111 125 |
Program 8 |
||||
|
|
126 140 |
Program 9 |
||
|
|
141 155 |
Program 10 |
||
|
|
156 170 |
Program 11 |
||
|
|
171 185 |
Program 12 |
||
|
|
186 200 |
Program 13 |
||
|
|
201 215 |
Program 14 |
||
|
|
216 230 |
Program 15 |
||
|
|
231 255 |
Program 16 |
||
7 |
Auto Program Speed |
000 250 |
Speed, slow to fast |
||
251 255 |
Sound Active Mode |
||||
|
|
||||
8 |
Dimmer |
000 255 |
Auto and Sound Programs |
5 |
Wash FX2 QRG Rev. 2 |
QUICK REFERENCE GUIDE
EN
3Ch
CHANNEL |
FUNCTION |
VALUE |
PERCENT/SETTING |
|
|
|
000 005 |
No function |
|
|
|
006 020 |
Program 1 |
|
|
|
021 035 |
Program 2 |
|
|
|
036 050 |
Program 3 |
|
|
|
051 065 |
Program 4 |
|
|
|
066 080 |
Program 5 |
|
|
|
081 095 |
Program 6 |
|
1 |
Auto Program |
096 110 |
Program 7 |
|
111 125 |
Program 8 |
|||
|
|
126 140 |
Program 9 |
|
|
|
141 155 |
Program 10 |
|
|
|
156 170 |
Program 11 |
|
|
|
171 185 |
Program 12 |
|
|
|
186 200 |
Program 13 |
|
|
|
201 215 |
Program 14 |
|
|
|
216 230 |
Program 15 |
|
|
|
231 255 |
Program 16 |
|
2 |
Auto Program Speed |
000 250 |
Speed, slow to fast |
|
251 255 |
Sound Active Mode |
|||
|
|
|||
3 |
Dimmer |
000 255 |
Auto and Sound Programs |
Wash FX2 QRG Rev. 2 |
6 |
GUÍA DE REFERENCIA RÁPIDA
ES
La Guía de referencia rápida (GRR) del Wash FX2 contiene información básica sobre el producto, como montaje, opciones de menú y valores DMX. Descargue el manual de usuario de www.chauvetdj.com para una información más detallada.
La información y especificaciones contenidas en esta GRR están sujetas a cambio sin previo aviso.
Estas notas de seguridad incluyen información importante sobre el montaje, uso y mantenimiento.
·Conecte siempre el producto a un circuito con toma de tierra para evitar el riesgo de electrocución.
·Asegúrese de que el cable de alimentación no está retorcido ni estropeado.
·Desconecte siempre el producto de la fuente de alimentación antes de limpiarlo o cambiar el fusible.
·Nunca desconecte el producto de la fuente de alimentación agarrando o tirando del cable.
·Si monta el producto en altura, asegúrese de que el soporte es adecuado para el peso del producto, y asegure siempre el producto con un cable de seguridad.
·Asegúrese de que no hay materiales inflamables cerca del producto cuando esté en funcionamiento.
·Evite la exposición directa de los ojos a la fuente de luz mientras es producto esté encendido.
·No toque la carcasa del producto cuando el producto esté en funcionamiento, porque la carcasa puede estar muy caliente.
·El producto no está concebido para una instalación permanente.
·¡El producto es para uso en interiores solamente!
·Está clasificado como IP20.
·No exponga el producto a lluvia o humedad.
·Asegúrese de que la tensión de la fuente de alimentación usada para el producto está dentro del rango establecido en el adhesivo o en el panel posterior del producto.
·Nunca conecte el producto a un atenuador o reostato.
·Sustituya el fusible del producto solo con otro fusible del mismo tipo y categoría.
·Instale el producto en una ubicación con ventilación adecuada
·Deje al menos a 20'' (50 cm) entre el producto y las superficies adyacentes.
·No bloquee las ranuras de ventilación de la carcasa del producto.
·No haga funcionar el producto a una temperatura ambiente superior a 104 °F (40 °C).
·Nunca mueva el producto agarrándolo por el cable de alimentación o por cualquier parte móvil.
·Use solamente el soporte de Montaje para mover este producto.
·En caso de un problema grave de funcionamiento, deje de usar el producto inmediatamente.
·Nunca intente abrir ni reparar el producto. Las reparaciones llevadas a cabo por personal no cualificado pueden provocar averías o funcionamiento defectuoso.
·Para evitar un desgaste innecesario y alargar su vida útil, desconecte complemente el producto de la alimentación, mediante el interruptor o desenchufándolo, durante los periodos en los que no se use.
Fuera de EE. UU., Reino Unido, Francia, Alemania Irlanda, México o Benelux póngase en contacto con su distribuidor para solicitar asistencia o devolver un producto. Visite www.chauvetdj.com para información de contacto.
•Wash FX2
•Cable de alimentación
•Tarjeta de garantía
•Guía de referencia rápida
Desembale su Wash FX2 y asegúrese de que ha recibido todas las partes en buen estado. Si la caja o los componentes parecen dañados, notifíqueselo inmediatamente al transportista, no a Chauvet.
7 |
Wash FX2 GRR Rev. 2 |
GUÍA DE REFERENCIA RÁPIDA
ES
Este producto tiene una fuente de alimentación con detección automática que puede funcionar con un rango de tensión de entrada de 100–240 VCA, 50/60 Hz.
Para evitar un desgaste innecesario y alargar su vida útil, desconecte completamente el producto mediante el interruptor o desenchufándolo durante periodos en que no se use.
Para ver el máximo número de Wash FX2 que se pueden alimentar en cadena a 120 V o a 240 V, consulte el Manual de usuario o la etiqueta del producto.
1.Desconecte el producto de la alimentación.
2.Haga cuña con la punta de un destornillador plano en la ranura del portafusibles.
3.Saque la tapa de seguridad de la carcasa.
4.Quite el fusible fundido de la sujeción en la parte frontal de la tapa de seguridad y sustituya el fusible con otro del mismo tipo y categoría.
Vuelva a insertar el portafusibles y conecte de nuevo la alimentación.
Antes de montar este producto, lea las Notas de seguridad.
Abrazadera de montaje
(como el CLP-15 de Chauvet)
Cable de
seguridad
(como el CH-05 de
Chauvet)
Soporte de montaje
(incluido)
Wash FX2 GRR Rev. 2 |
8 |
GUÍA DE REFERENCIA RÁPIDA
ES
BOTÓN FUNCIÓN
<MENU> Sale del menú o función actual
<UP> Navega hacia arriba por la lista de menú y aumenta el valor numérico cuando está en una función <DOWN> Navega hacia abajo por la lista de menú y disminuye el valor numérico cuando está en una función
<ENTER> Habilita el menú actualmente en pantalla o configura el valor seleccionado actualmente dentro de la función seleccionada
MODO |
NIVELES DE PROGRAMACIÓN |
DESCRIPCIÓN |
||
Modo DMX |
3Ch |
d001-512 |
|
|
|
Configura la dirección inicial DMX |
|||
8Ch |
||||
|
28CH |
|
|
|
Colores |
C-- |
C001–022 |
Colores estáticos |
|
estáticos |
||||
|
|
|
||
Programas |
P-- |
P 1–16 |
Programas automáticos |
|
automáticos |
||||
|
|
|
||
Velocidad |
S-- |
S001–100 |
Velocidad de programa para P 1–16 |
|
Atenuador de |
dIM |
L001–255 |
Atenuador de LED cuádruples para programas |
|
programa |
||||
|
|
|
||
Activo por |
Snd |
Snd1–9 |
Programas activado por sonido |
|
sonido |
||||
|
|
|
||
Sensibilidad al |
SenS |
u001-100 |
Sensibilidad al sonido |
|
sonido |
||||
|
|
|
||
Mezcla de |
|
r000–255 |
|
|
|
g000–255 |
Colores estáticos personalizados |
||
colores |
u-- |
|
Combina rojo, verde, azul y UV |
|
personalizados |
|
b000–255 |
||
|
|
u000–255 |
|
|
Modo |
SEt |
on |
Activa o desactiva los infrarrojos |
|
Infrarrojos |
|
|||
oFF |
||||
|
|
El Wash FX2 puede funcionar con un controlador DMX cuando se enlaza por conexiones serie DMX. Las instrucciones para conectar y configurar este producto para funcionamiento DMX están en el Manual de usuario. Si no está familiarizado con DMX, descargue el Manual DMX de www.chauvetdj.com.
Para asegurarse acceso total a todos los canales en cada modo DMX, la dirección DMX más recomendable es 484.
El Wash FX2 usa la conexión de datos DMX para su modo Maestro/Esclavo. Las instrucciones para conectar y configurar este producto para funcionamiento Maestro/Esclavo están en el Manual de usuario.
El Wash FX2 es totalmente compatible con el control remoto por infrarrojos (IRC-6) de CHAUVET DJ. Para información adicional sobre el IRC-6 o para descargar las instrucciones, consulte www.chauvetdj.com.
9 |
Wash FX2 GRR Rev. 2 |
GUÍA DE REFERENCIA RÁPIDA
ES
28Ch
CANAL |
FUNCIÓN |
VALOR |
PORCENTAJE/CONFIGURACIÓN |
|
|
|
|
000 005 |
Sin función |
|
|
|
|
006 020 |
Programas automático 1 |
|
|
|
|
021 035 |
Programas automático 2 |
|
|
|
|
036 050 |
Programas automático 3 |
|
|
|
|
051 065 |
Programas automático 4 |
|
|
|
|
066 080 |
Programas automático 5 |
|
|
|
|
081 095 |
Programas automático 6 |
|
|
1 |
Programas automáticos |
096 110 |
Programas automático 7 |
|
|
111 125 |
Programas automático 8 |
|
|||
|
|
126 140 |
Programas automático 9 |
|
|
|
|
141 155 |
Programas automático 10 |
|
|
|
|
156 170 |
Programas automático 11 |
|
|
|
|
171 185 |
Programas automático 12 |
|
|
|
|
186 200 |
Programas automático13 |
|
|
|
|
201 215 |
Programas automático 14 |
|
|
|
|
216 230 |
Programas automático 15 |
|
|
|
|
231 255 |
Programas automático 16 |
|
|
2 |
Velocidad del programa |
000 250 |
Velocidad, lenta a rápida |
|
|
251 255 |
Modo Activo por sonido |
||||
|
|
||||
3 |
Atenuador |
000 255 |
Ajustes de velocidad de atenuador |
|
|
4 |
Estroboscopio |
000 255 |
Estroboscopio, lento a rápido |
|
|
5 |
Zona Roja 1 |
000 255 |
0–100% |
|
|
6 |
Zona Verde 1 |
000 255 |
0–100% |
|
|
7 |
Zona Azul 1 |
000 255 |
0–100% |
|
|
8 |
Zona UV 1 |
000 255 |
0–100% |
|
|
9 |
Zona Roja 2 |
000 255 |
0–100% |
|
|
10 |
Zona Verde 2 |
000 255 |
0–100% |
|
|
11 |
Zona Azul 2 |
000 255 |
0–100% |
|
|
12 |
Zona UV 2 |
000 255 |
0–100% |
|
|
13 |
Zona Roja 3 |
000 255 |
0–100% |
|
|
14 |
Zona Verde 3 |
000 255 |
0–100% |
|
|
15 |
Zona Azul 3 |
000 255 |
0–100% |
|
|
16 |
Zona UV 3 |
000 255 |
0–100% |
|
|
17 |
Zona Roja 4 |
000 255 |
0–100% |
|
|
18 |
Zona Verde 4 |
000 255 |
0–100% |
|
|
19 |
Zona Azul 4 |
000 255 |
0–100% |
|
|
20 |
Zona UV 4 |
000 255 |
0–100% |
|
|
21 |
Zona Roja 5 |
000 255 |
0–100% |
|
|
22 |
Zona Verde 5 |
000 255 |
0–100% |
|
|
23 |
Zona Azul 5 |
000 255 |
0–100% |
|
|
24 |
Zona UV 5 |
000 255 |
0–100% |
|
|
25 |
Zona Roja 6 |
000 255 |
0–100% |
|
|
26 |
Zona Verde 6 |
000 255 |
0–100% |
|
|
27 |
Zona Azul 6 |
000 255 |
0–100% |
|
|
28 |
Zona UV 6 |
000 255 |
0–100% |
|
|
|
|
|
|
|
|
Wash FX2 GRR Rev. 2 |
|
10 |
GUÍA DE REFERENCIA RÁPIDA
ES
8Ch
CANAL |
FUNCIÓN |
VALOR |
PORCENTAJE/CONFIGURACIÓN |
|
1 |
Rojo |
000 255 |
0–100% |
|
2 |
Verde |
000 255 |
0–100% |
|
3 |
Azul |
000 255 |
0–100% |
|
4 |
UV |
000 255 |
0–100% |
|
5 |
Estroboscopio |
000 255 |
Estroboscopio, lento a rápido |
|
|
|
000 005 |
Sin función |
|
|
|
006 020 |
Programas automático 1 |
|
|
|
021 035 |
Programas automático 2 |
|
|
|
036 050 |
Programas automático 3 |
|
|
|
051 065 |
Programas automático 4 |
|
|
|
066 080 |
Programas automático 5 |
|
|
|
081 095 |
Programas automático 6 |
|
6 |
Programas automáticos |
096 110 |
Programas automático 7 |
|
111 125 |
Programas automático 8 |
|||
|
|
126 140 |
Programas automático 9 |
|
|
|
141 155 |
Programas automático 10 |
|
|
|
156 170 |
Programas automático 11 |
|
|
|
171 185 |
Programas automático 12 |
|
|
|
186 200 |
Programas automático13 |
|
|
|
201 215 |
Programas automático 14 |
|
|
|
216 230 |
Programas automático 15 |
|
|
|
231 255 |
Programas automático 16 |
|
7 |
Velocidad del programa |
000 250 |
Velocidad, lenta a rápida |
|
251 255 |
Modo Activo por sonido |
|||
|
|
|||
8 |
Atenuador |
000 255 |
Ajustes de velocidad de atenuador |
11 |
Wash FX2 GRR Rev. 2 |
GUÍA DE REFERENCIA RÁPIDA
ES
3Ch
CANAL |
FUNCIÓN |
VALOR |
PORCENTAJE/CONFIGURACIÓN |
|
|
|
000 005 |
Sin función |
|
|
|
006 020 |
Programas automático 1 |
|
|
|
021 035 |
Programas automático 2 |
|
|
|
036 050 |
Programas automático 3 |
|
|
|
051 065 |
Programas automático 4 |
|
|
|
066 080 |
Programas automático 5 |
|
|
|
081 095 |
Programas automático 6 |
|
1 |
Programas automáticos |
096 110 |
Programas automático 7 |
|
111 125 |
Programas automático 8 |
|||
|
|
126 140 |
Programas automático 9 |
|
|
|
141 155 |
Programas automático 10 |
|
|
|
156 170 |
Programas automático 11 |
|
|
|
171 185 |
Programas automático 12 |
|
|
|
186 200 |
Programas automático13 |
|
|
|
201 215 |
Programas automático 14 |
|
|
|
216 230 |
Programas automático 15 |
|
|
|
231 255 |
Programas automático 16 |
|
2 |
Velocidad del programa |
000 250 |
Velocidad, lenta a rápida |
|
251 255 |
Modo Activo por sonido |
|||
|
|
|||
3 |
Atenuador |
000 255 |
Ajustes de velocidad de atenuador |
Wash FX2 GRR Rev. 2 |
12 |