Beckhoff C6250-0060, C6250-0050 Installation And Operating Instructions Manual
Installation and Operating instructions for
Control Cabinet PC
C6250 up to -0060
Version: 1.6
Date: 2018-02-16
Table of contents
Table of contents
1.
2.
3.
4.
General instructions 3
Notes on the Documentation 3
Liability Conditions 3
Trademarks 3
Patent Pending 3
Copyright 3
State at Delivery 3
Delivery conditions 3
Description of safety symbols 4
Basic safety measures 4
Operator's obligation to exercise diligence 5
Operator requirements 5
Appropriate Use 5
Product Description 6
Appropriate Use 6
Structure 6
Interfaces up to C6250-0050 8
PS/2 connections 8
Parallel interface 8
Serial interfaces 8
Video connection 8
USB interfaces 8
Network connection 8
Sound-On-Board 8
Additional plug-in cards (optional) 8
Interfaces C6250-0060 9
PS/2 connections 9
Serial interfaces 9
USB interfaces 9
Network connection 9
Sound-On-Board 9
DVI-I (Digital Visual Interface) 9
DVI-D (Digital Visual Interface) 9
DisplayPort 9
Additional plug-in cards (optional) 9
Installation Instructions 10
Transport and Installation 10
Transport 10
Unpacking 10
Installation of the PC in the control cabinet 11
Earthing measures 11
Power Supply Connection 12
Fitting the Power Supply Cable 13
Pin assignment and cable requirements 14
Connecting devices 15
Connecting cables 15
Check voltage rating and connect. 15
Operating Instructions 16
Switching the Industrial PC on and off 16
First switching on and driver installation 16
Maintenance 17
Cleaning the Industrial PC 17
Replacing the battery on the motherboard 17
Servicing 17
Shutting down 17
Disposal 17
C6250 1
Table of contents
5.
6.
7.
Troubleshooting 18
Fault correction 18
Service and Support 19
Beckhoff's branch offices and representatives 19
Beckhoff headquarters 19
Beckhoff Support 19
Beckhoff Service 19
Assembly dimensions 20
Appendix 22
Technical data 22
Approvals 22
FCC: Federal Communications Commission 22
Radio Frequency Interference Statement 22
FCC: Canadian Notice 22
2 C6250
General instructions
General instructions
Notes on the Documentation
This description is only intended for the use of trained specialists in control
and automation engineering who are familiar with the applicable national
standards. It is essential that the following notes and explanations are
followed when installing and commissioning these components.
The responsible staff must ensure that the application or use of the
products described satisfy all the requirements for safety, including all the
relevant laws, regulations, guidelines and standards.
Liability Conditions
The documentation has been prepared with care. The products described
are, however, constantly under development. For that reason the
documentation is not in every case checked for consistency with
performance data, standards or other characteristics. In the event that it
contains technical or editorial errors, we retain the right to make alterations
at any time and without warning. No claims for the modification of products
that have already been supplied may be made on the basis of the data,
diagrams and descriptions in this documentation.
All pictures shown in the documentation are exemplary. Illustrated
configurations can differ from standard.
Trademarks
Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®
and XFC® are registered trademarks of and licensed by Beckhoff
Automation GmbH.
Other designations used in this publication may be trademarks whose use
by third parties for their own purposes could violate the rights of the
owners.
Patent Pending
The EtherCAT Technology is covered, including but not limited to the
following patent applications and patents:
EP1590927, EP1789857, DE102004044764, DE102007017835
with corresponding applications or registrations in various other countries.
The TwinCAT Technology is covered, including but not limited to the
following patent applications and patents:
EP0851348, US6167425 with corresponding applications or registrations in
various other countries.
Copyright
© Beckhoff Automation GmbH & Co.KG.
The reproduction, distribution and utilization of this document as well as the
communication of its contents to others without express authorization are
prohibited. Offenders will be held liable for the payment of damages. All
rights reserved in the event of the grant of a patent, utility model or design.
State at Delivery
All the components are supplied in particular hardware and software
configurations appropriate for the application. Modifications to hardware or
software configurations other than those described in the documentation
are not permitted, and nullify the liability of Beckhoff Automation
GmbH & Co.KG.
Delivery conditions
In addition, the general delivery conditions of the company Beckhoff
Automation GmbH & Co.KG apply.
C6250 3
General instructions
Description of safety symbols
The following safety symbols are used in this operating manual. They are
intended to alert the reader to the associated safety instructions.
Danger
This symbol is intended to highlight risks for the life or health of personnel.
Warning
This symbol is intended to highlight risks for equipment, materials or the
environment.
i
Note
This symbol indicates information that contributes to better understanding.
Basic safety measures
Only switch the PC off after
closing the software
Before the Industrial PC is switched off, software that is running must
be properly closed.
Otherwise it is possible that data on the hard disk is lost. Please read the
section on Switching the Industrial PC on and off.
Warning
Switch off all parts of the equipment, then uncouple the fieldbus!
Before opening the housing of the PC, and whenever the PC is being used
for purposes other than plant control, such as during functional tests
following repair, all parts of the equipment must first be switched off, after
which the Industrial PC can be uncoupled from the plant.
Pulling out the fieldbus connection plug uncouples the PC (optional).
Items of equipment that have been switched off must be secured against
being switched on again.
The Industrial PC’s power supply unit must be supplied with 100-240 VAC
or 24 V
DC
(optional).
Danger
Do not open the power supply unit while voltage is applied!
The supply voltage must be switched off before the power supply unit
housing is opened.
Do not exchange any parts when under power!
When components are being fitted or removed, the supply voltage must be
switched off.
Fitting work on the Industrial PC can result in damage:
• If metal objects such as screws or tools fall onto operating circuit
boards.
• If connecting cables internal to the PC are removed or inserted
during operation.
• If plug-in cards are removed or inserted when the PC is switched
on.
4 C6250
General instructions
Operator's obligation to exercise diligence
The operator must ensure that
• the Industrial PC is only used for its intended use (see also
Product Description).
• the Industrial PC is in a sound condition and in working order
during operation.
• the operation manual is in good condition and complete, and
always available for reference at the location of the Industrial PC.
• the Industrial PC is operated, maintained and repaired only by
sufficiently qualified and authorised personnel.
• the personnel is instructed regularly about relevant occupational
safety and environmental protection aspects, and is familiar with
the operating manual and in particular the safety notes contained
herein.
• none of the safety and warning notes attached to the Industrial PC
are removed, and that all notes remain legible.
National regulations
depending on the machine
type
Depending on the type of machine and plant in which the Industrial PC is
being used, there will be national regulations for the control of such
machines and plant that the operator must observe. These regulations
cover, amongst other things, the intervals between inspections of the
controller.
The operator must initiate such inspections in good time.
Warning
Only trained persons may open the Industrial PC housing!
The operator is responsible for ensuring that only trained electrical staff
opens the housing of the Industrial PC.
Procedure in the event of a
fault
In the event of a fault in the Industrial PC, appropriate measures can be
determined with the aid of the list in the Fault correction section.
Operator requirements
Read the operating
instructions
Every user of the Industrial PC must have read these operating
instructions.
Software knowledge
Every user must be familiar with any of the functions of the software
installed on the PC that he can reach.
Appropriate Use
The C6250 Industrial PC is designed for mounting in control cabinets in
machine and plant engineering applications. The ambient conditions
specified in the technical data (see Appendix) must be observed for both
operation and storage of the C6250 Industrial PC.
C6250 5
Product Description
Product Description
Appropriate Use
The C6250 Industrial PC is designed for mounting in control cabinets in
machine and plant engineering applications. The ambient conditions
specified in the technical data (see Appendix) must be observed for both
operation and storage of the C6250 Industrial PC.
Structure
Front view of the C6250
(Similar photograph)
Opening the housing
To open the PC housing, initially rotate the two fast closing screws (see
photograph above) by 90 degrees in either direction using a screwdriver.
The inner chassis can now be pulled out on telescopic guide supports (see
photograph below).
Removable
inner chassis
Undo the two screws (1) of the upper housing cover (2). The upper housing
cover can now be tilted upwards (see photograph below), thus providing
access to the disk drive, the 3 ½ inch hard disk, the processor, the memory
and the plug-in cards.
2
1
1
6 C6250