Bauknecht GSI PRIMELINE 9617 IN installation and maintenance instructions

0 (0)
Bauknecht GSI PRIMELINE 9617 IN installation and maintenance instructions

Before using the dishwasher, read the installation and maintenance instructions carefully!

GB GSI Primeline 9617

1. OVERVIEW

Programme selector

START button

Switches “on” when the dishwasher is operating. Flashes when a fault occurs. Switches off at the end of the programme.

START button RESET function:

Press this button for at least 2 seconds; the selected programme and options are cancelled. Main failure displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING.

Detailed instructions are given in chapter 5 “What to do, in the event of...”.

Rinse aid level indicator and salt level indicator

They light up when rinse aid or salt need to be added. Add just before starting a wash cycle.

Fault indication and wash time display

With normal operation, the display indicates residual time (h:mm), while with the “Delayed start” function selected it indicates time remaining until the start of the programme (hh).

If “F..” appears on the display, see chapter 5 “What to do, in the event of.

Delayed start” button

Press the button as required to delay the start of the programme. Adjustable from 1 to 24 hours. With each press of the button, the delayed start indicator increases by one hour and after 24 restarts from 00. Then press the START button. The dishwasher will start after the set time.

Detergent setting upon initial use and when using a different type of detergent

1.Select the third programme in the relative table.

2.Press the START button for approx. 7 sec. to change the display.

3.Using the START button, select the desired detergent:

Display shows: 2 -1 = 2 in 1, 3 -1 = 3 in 1, 4 -1 = other combined action detergents (in this way, the rinse aid and/or salt indicator is deactivated). Display shows OFF = Powder detergent (factory setting).

(rinse aid level and salt level indicator activated).

4.Switch the appliance off and then switch it on again. The selected detergent will be displayed for approx. 3 sec.

Half Load/Multizone button

Load the upper or lower rack only.

Pressonce=washupper rack(theindicatorlight/symbollightsup) Presstwice=washthe lower rack(theindicatorlight/symbollightsup) Press 3 times = Off (Half load/Multizone deactivated).

When washing without the top rack, press the “Half load” (i.e. “wash bottom rack”) button twice; the corresponding indicator/symbol lights up.

Power Clean

Intensive wash with additional water jets and greater loading flexibility in the bottom rack.

On / Off Button

Table 1.1.

 

 

 

Table of programmes

 

Detergent

Consumption 1)

 

 

 

 

 

 

dispenser

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

P

 

 

Programmes

Selectable

Loading instructions

large

small

Litres

kWh

Minutes

 

 

extra

 

 

 

 

functions

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

Auto Sensor

50-65°C

Recommended programme for

X

X

11-16

1.10-1.50

100-130 ± 1)

 

 

routine washes, with dried-on

 

 

 

 

 

food (e.g. EN 50242).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

Pre-Rinse

cold

Crockery to be washed later.

4.0

0.03

14 ± 1)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

Rapid

40°C

Lightly soiled crockery,, without

X

10.0

0.65

30 ±

1)

 

 

dry residuals.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

 

 

Bio Normal 2)

50°C

Normally soiled crockery,.

X

X

12.0

1.05

165 ±

1)

 

 

 

 

Energy-saving programme.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Normally - heavily soiled crockery,

 

 

 

 

 

 

 

5

 

 

Hygiene + 3)

 

with additional antibacterial wash.

X

X

13.0

1.50

115 ± 1)

 

 

 

Programme interruption (e.g. due

 

 

 

 

 

to door opening) can compromise

 

 

 

 

 

 

 

 

 

 

 

 

elimination of germs.

 

 

 

 

 

 

 

Recommended programme for

6 Intensive 70°C heavily soiled crockery, especially X X 14.0 1.55 155 ± 1) suitable for pans and saucepans.

1)Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g. different loads, options, different sensor settings (only with sensor programmes), different water supply temperatures, as well as water hardness and power supply voltage.

2)Energy label programme in compliance with EN 50242. - Information for Test Laboratories: for more detailed information on the EN comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3)The antibacterial action has been shown in collaboration with the Pasteur Institute, Lille (France), in conformity with. Standard NF EN 13697 - November 2001.

5019 496 01078

1

2. QUICK REFERENCE GUIDE

Detailed instructions are given on the following pages; also see section “5. What to do, in case of...”

1.Switch on the appliance

2.Select a programme

3.Select the type of detergent

Press the ON/OFF button.

Press the button “Select programme” or the programme selector to display the selected programme. If required, select possible options.

The detergent selection procedure varies depending on the dishwasher model. Chapter “1. Overview” provides instructions for selecting detergent type.

4. Fill in the detergent

4a. Powder/gel/tabs

 

 

 

 

 

Fill the detergent dispenser compartments in

A B C

 

 

 

 

accordance with the wash programme selected.

 

 

Large compartment A for every wash cycle, additional

 

 

 

 

 

small compartment B for programmes with pre-wash

 

 

 

 

 

(see table 1.1.).

 

 

 

 

 

4b. Combined action detergents (2 in 1/3 in 1/... etc.)

 

 

 

 

 

Place the detergent in compartment A or in the cutlery

 

 

 

 

 

basket, as per the manufacturer's recommendations.

 

 

 

 

 

 

 

 

 

5.Check the rinse aid level

6.Check the salt level

7.Load the racks

8.Open the water tap and close the door

9.Start the appliance

Wash cycle

Visual indicator in dispenser C

dark

 

sufficient rinse aid present,

clear

 

add rinse aid (approx. 100 ml).

The indicator lamp on the control panel lights up when rinse aid needs to be added. Not all models are equipped with such an indicator.

Depending on the model:

window in salt reservoir cap on bottom of appliance inside

orange

 

when sufficient salt is present,

clear

 

when salt needs to be added.

The indicator lamp on the control panel lights up when salt needs to be added. Even once salt has been added, the indicator lamp only switches off after several wash cycles!

Make sure that the spray arms can turn freely and are not impeded by crockery or cutlery in the racks.

Detailed instructions on loading the racks are given in chapter “3. How to use the appliance”, under “How to load the racks”.

Press the START button.

If the appliance is switched off during a wash cycle, when switched on again it will resume the cycle from where it was interrupted. Care must be taken when opening the door, as steam will escape!

Changing the programme in progress:

-Keep the START button pressed for about 2 seconds until the START indicator goes off.

-(Water drains for up to 60 seconds).

-Select the programme again.

-Press the Start button.

10.End of programme

The START indicator lamp switches off at the end of the programme.

 

 

 

11.Switch off the

Press the OFF button. All the indicator lamps switch off.

appliance

 

 

 

 

 

 

12.Turn off the water

Unload the appliance, starting from the lower rack in order to avoid any

tap, unload the racks

residual drips of water falling onto crockery below.

 

 

 

2

3. HOW TO USE THE APPLIANCE

PROGRAMME SELECTION

Press the button “Select programme” or the programme selector to display the selected programme. The appliance must be switched on. If required, select possible options. The corresponding indicator lights up. The correct programme and the selectable functions are given in table 1.1 on page 1.

Programme times stated in the table were obtained under normal conditions and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programmes as a result of the appliance's automatic calibration system.

HOW TO FILL THE DETERGENT DISPENSER

Only fill the detergent dispenser prior to starting a wash programme. Only use detergents specially recommended for dishwashers, observing the manufacturer's recommended dosage. Observe the manufacturer's safety warnings!

Open the detergent dispenser compartments by pushing the left lever (lever 1) of the dispenser. a. Powder/gel/tabs

Fill the detergent dispenser compartments in accordance with the wash programme selected (table 1.1).

Programmes without pre-wash:

pour the entire recommended dosage into compartment A. Programmes with pre-wash:

pour 2/3 of the recommended dosage into the large compartment A and 1/3 into the small compartment B.

Dishwasher tabs should be placed, according to the manufacturer's recommendations, in compartment A or in the cutlery basket.

If the “Half load” option is selected, detergent dosage should be reduced by approximately 1/3.

b. Combined action detergents (2 in 1/3 in 1/... etc.)

Combined action detergents should be placed, according to the manufacturer's recommendations, in compartment A or in the cutlery basket.

Firmly press the detergent compartment lid shut after filling.

Lever 1

Large Small

compartment A compartment B

Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.

The guarantee is not applicable if faults are caused by the use of these products.

HOW TO CHECK/FILL/ADJUST RINSE AID

Not necessary when using a combined action detergent.

a. How to check the rinse aid level

Check the visual indicator C on the rinse aid dispenser: dark = sufficient rinse aid, clear = add rinse aid.

In the case of appliances with an electric indicator on the

Lever 2

Indicator C

control panel, the rinse aid indicator lamp

lights up red

 

 

 

 

when rinse aid needs to be added.

 

 

 

 

 

 

 

 

 

 

b. How to fill the rinse aid dispenser

Open the rinse aid dispenser by pressing the right lever (lever 2) of the dispenser.

Fill the dispenser with rinse aid up to the “max” line

max

(approx. 100 ml).

 

Shut the lid again.

 

Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the appliance.

3

Loading...
+ 5 hidden pages