Before using the dishwasher, read the installation and maintenance instructions carefully!
GB GSI 5972
1. OVERVIEW
Programme selection button
Press the button (repeatedly) until the indicator lamp of the desired programme lights up (see table 1.1).
At the end of the wash cycle, the last programme selected is memorized.
Half Load/Multizone
Load the upper or lower rack only.
Factory setting = Wash upper and lower rack (both indicator lamps light up)
Press once = Wash lower rack (the indicator lamp lights up) Press twice = Wash upper rack (the indicator lamp lights up) At the end of the programme, the most recently selected setting remains memorised.
If the upper rack is not being washed, the “Wash lower rack” indicator lamp should be lit.
Rotating Power Clean
This function is activated by pressing (short) the button (the indicator lamp lights up).
High pressure with an additional jet for better washing results and greater lower rack load flexibility. At the end of the programme, the most recently selected setting remains memorised.
Detergent setting upon initial use and when using a different type of detergent
Indicator lamp off = Powder/gel detergent (factory setting). If using combined detergents, press and hold the button for 3
seconds; the indicator lamp lights up = rinse aid and salt indicators are deactivated.
From water hardness level 5, the salt indicator remains active. At the end of the programme, the most recently selected setting remains memorised.
Fault indication and wash time display
In normal operation it indicates the remaining time (h:min), whereas with “Delayed start” selected it indicates the time remaining until programme start (e.g. h 01). If using a sensor programme, a dotted line indicates that the calibration process is underway (lasting up to 20 minutes).
In the presence of a fault indication “F.. / E..”, refer to Section 5 “What to do if...”.
Delayed start button
Push the button (repeatedly) to delay the start of the programme. Adjustable from 1 to 24 hours. With each press of the button, the delayed start indicator increases by 1 hour, and after “h 24” returns to “h 00”. Then press the START button. The wash programme will start after the set time.
Start/Resume button
The indicator lamp lights up during operation, flashes when the programme is interrupted before completion and switches off at the end of the programme.
Cancel/Off button
Press the button to switch the dishwasher off or to interrupt the selected programme.
If the Cancel/Off indicator lamp flashes repeatedly, this indicates a fault: see chapter 5 “What to do if...”.
Salt level indicator and rinse aid level indicator
These light up at the end of the programme if salt or rinse aid needs topping up. Only add just before starting a wash cycle.
Table 1.1.
|
|
|
Overview of programmes |
Detergent |
Consumption 1) |
|
|
||||||||
|
|
|
dispenser |
|
|
||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
P |
|
|
Programmes |
|
Additional |
Description of |
large |
small |
Litres |
kWh |
Minutes |
||||
|
|
|
options |
programme |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
||||
1 |
|
|
Sensor |
40-70°C |
|
|
|
Normally or heavily soiled crockery, |
X |
X |
7-14 |
0.99-1.80 |
70-185± |
1) |
|
|
|
|
|
|
|||||||||||
|
|
|
|
|
including pots and pans. |
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
|
|
Pre-Rinse |
cold |
|
|
|
Crockery to be washed later. |
— |
— |
4.0 |
0.03 |
14 ± 1) |
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
|
|
Quickwash |
45°C |
|
|
|
Lightly soiled crockery, with no dried-on |
X |
— |
11.0 |
0.80 |
30 ± |
1) |
|
|
|
|
|
|
food. |
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
|
|
Bio Normal 2) |
50°C |
|
|
|
Normally soiled crockery. Energy-saving |
X |
X |
13.0 |
0.93 |
200 ± |
1) |
|
|
|
|
|
|
programme. |
|
|
||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
|
|
Daily Quickwash |
60°C |
|
|
|
Normally soiled crockery. |
X |
— |
10.0 |
1.30 |
80 ± 1) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 |
|
|
Intensive |
70°C |
|
|
|
Recommended programme for heavily |
|
|
|
|
155 ± 1) |
||
|
|
|
|
|
soiled crockery, especially suitable for |
X |
X |
14.0 |
1.55 |
||||||
|
|
|
|
|
|||||||||||
|
|
|
|
|
|
|
|
pots and pans. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1)Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads, extra functions, settings, water supply temperatures, water hardness and power supply voltage.
2)Programme for energy data label in conformity with EN 50242. - Information for Test Laboratories: for detailed information on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
5019 496 01141
1
2. QUICK REFERENCE GUIDE
Detailed instructions are given on the following pages; also see section “5. What to do if...”.
1.Switch the appliance on
2.Select the right type of detergent
3.Fill the detergent dispenser
The dishwasher switches on automatically when any button is pressed except for the button. If no button is pressed within 30 seconds, the appliance switches to
Energy Saving mode.
Depending on the dishwasher model
4. Check the rinse aid level
5.Set the water hardness level
Press and hold the programme selection button + Start/Resume button for at least three seconds.
Press the |
|
|
programme |
Press the |
|
selection |
||
Start/Resume |
||
button |
||
button |
||
from 1 |
||
|
||
to 7 times. |
|
6. Check the salt level
7. |
Load the racks |
|
|
8. |
Turn on the water |
|
|
|
tap, close the door |
|
|
9. |
Select a programme, |
Programme |
Start/ |
selection |
|||
|
and start |
button |
Resume |
|
|
|
|
|
|
Fill crockery: beware of hot steam! The |
|
|
|
start indicator blinks, close the door, press |
|
|
Wash cycle |
the Start button again, the programme |
resumes from where it had stopped (as happens after a power shortage as well).
10.End of programme 11.Open the door
12.Turn off the water tap, unload the racks
Change the programme in progress:
-Press the “Cancel/Off” button.
-(Water drains for up to 60 seconds).
-Select a new programme.
-Press the START button.
2
3. HOW TO USE THE APPLIANCE
HOW TO FILL THE DETERGENT DISPENSER
Only fill the detergent dispenser prior to starting a wash programme. Only use detergents specially recommended for dishwashers, observing the manufacturer’s recommended dosage. Observe the manufacturer’s safety warnings!
Press the left button (button 1) on the dispenser to open the detergent dispenser compartments.
a. Powder/gel/tabs
Fill the detergent dispenser compartments in accordance with the wash programme selected (table 1.1).
Programmes without pre-wash:
Pour the entire recommended dosage into compartment A. Programmes with pre-wash:
Pour 2/3 of the recommended dosage into the large compartment A and 1/3 into the small compartment B.
Dishwasher tabs should be placed, as per the manufacturer’s recommendations, in compartment A.
If the “Half load” option is selected, detergent dosage should be reduced by approximately 1/3.
b. Combined action detergents (2 in 1/3 in 1/... etc.)
Dishwasher tabs should be placed, as per the manufacturer’s recommendations, in compartment A.
Shut and firmly press the detergent compartment lid shut after filling.
Large |
Button 1 |
Small |
compartment A |
compartment B |
Detergents with rinse aid incorporated may be effective only with longer programmes. In the case of shorter programmes, detergent residue may be a problem (if necessary, use powder detergent). Detergents with rinse aid incorporated tend to form excess suds.
The guarantee is not applicable if faults are caused by the use of these products.
HOW TO CHECK/FILL/ADJUST RINSE AID
Not necessary when using a combined action detergent.
a. How to check the rinse aid level
Check the visual indicator C on the dispenser: dark = sufficient rinse aid, clear = add rinse aid.
In the case of appliances with an electric indicator on the |
Indicator C |
|
control panel, the rinse aid indicator |
lights up at the end |
of the wash cycle when rinse aid needs to be added.
b. How to fill the rinse aid dispenser |
|
|
max |
Press the right button on the dispenser (button 2 ) to open |
|
|
|
the rinse aid compartment. |
|
|
|
Fill the dispenser with rinse aid up to the “max” line |
|
|
|
(approx. 150 ml). |
|
|
Button 2 |
Shut the lid again. |
|
|
|
|
|
|
Only use rinse aids recommended for use in domestic dishwashers.
If rinse aid is accidentally spilt, immediately remove it to avoid the formation of excessive suds which could cause appliance malfunctioning.
c. How to adjust the rinse aid dosage regulator:
The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4).
Press the button 2 to open the cover.
Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again.
If the dishes often have whitish streaks: reduce the dosage by turning the dial to a lower setting (1-3). Dishes did not dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
3