Avocent 590-222-501M User Manual

AMX

Installer/User Guide

Switch Series

USA Notification

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canadian Notification

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada.

Japanese Approvals

Safety and EMC Approvals and Markings

UL, FCC, cUL, ICES-003, CE, VCCI, C-Tick

AMX® Switch Series

Installer/User Guide

Avocent, the Avocent logo, The Power of Being There, AMX, AMWorks, OSCAR, AutoView, DSR, OutLook, SwitchView and XP are registered trademarks of Av ocent Corporation or its affiliates in the U.S. and other countries. All other marks are the property of their respective owners.

Instructions

This symbol is intended to alert (servicing) instructions in the literature accompanying the appliance.

Dangerous Voltage

the user to the presence of important operating and maintenance

This symbol is intended to alert the user to the presence o product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Power On

This symbol indicates the principal on/off switch

Power Off

This symbol indicates the principal on/of

Protective Grounding Terminal

This symbol indicates a terminal which must be connected to earth ground prior to making any other connections to the equipment.

f switch

f uninsulated dangerous voltage within the

is in the on position.

is in the off position.

Table of Contents

List of Figures ................................................................................................................ vii

List of Tables................................................................................................................... ix

Chapter 1: Product Overview.......................................................................................... 1

Glossary.............................................................................................................................................3

Component Overview.........................................................................................................................4

The AMX switch.................................................................................... ......................................5

The AMX user station .............................................................. ..................................................5

The AMX switch IQ modules ....................................................... ...............................................6

UTP cables..................................................................................................................................6

Safety Precautions .............................................................................................................................7

Chapter 2: Installation ..................................................................................................... 9

AMX Switching Systems ....................................................................................................................9

Getting Started............................................................................................... ....................................9

Rack Mounting an AMX Switch........................... ................................................ ............................13

Installing an AMX Switch .................................................. ................................................ ..............13

Connecting Target Devices to the AMX Switch...............................................................................15

Connecting Users to the AMX Switching System.............................................................................17

Connecting a Local Server to the AMX Switching System ..............................................................18

Connecting a User Station for Switch Redundancy.........................................................................19

Connecting an AMIQDM Module for Dual Port Output.................................................................20

Installing a Cascaded AMX Switching System................................................................................21

Blocking and non-blocking configurations...............................................................................22

Installing AMWorks Software..........................................................................................................26

Configuring AMWorks software...............................................................................................27

AMX Switching Systems in Broadcast Environments......................................................................27

Using nVision routers................................................. ................................................ ..............28

Flash Upgrading the AMX Switching System..................................................................................29

Unit LEDs ........................................................................................................................................29

AMX switch...............................................................................................................................29

AMX user station ......................................................................................................................30

IQ module .................................................. ................................................ ...............................31

iii

iv AMX Switch Series Installer/User Guide

Chapter 3: Operations ................................................................................................... 33

OSCAR Interface Overview .............................................................................................................33

Accessing the OSCAR interface................................................................................................33

Changing the OSCAR hotkey sequence....................................................................................34

OSCAR interface tabs...............................................................................................................34

Target Devices................................................................................................................................. 35

Connection modes.....................................................................................................................35

Accessing target devices...........................................................................................................35

Setting a target device hotkey............................................................ .......................................36

Setting a quick switch hotkey for target devices .......................................................................37

Setting a local switch hotkey.....................................................................................................38

Setting a target flag ........................... ................................................ ....................................... 39

Viewing MDM target device information.................................................................................40

Scanning the switching system..................................................................................................41

Users................................................................................................................................................43

Logging in as a user .................................................................................................................43

Logging out...............................................................................................................................44

Managing the user database.....................................................................................................44

Administering security settings.................................................................................................45

Configuring Keyboard Settings .......................................................................................................48

Keyboard layout........................................................................................................................48

Keyboard type....................................... ....................................................................................50

Keyboard translation .................................................... ................................................ ...........51

Using Audio and Serial Data Emulation.........................................................................................52

Viewing IQ Module Version Information ........................................................................................54

User Stations.................................... ................................................ ................................................55

Locking user station settings ....................................................................................................56

Persistent mode.........................................................................................................................57

User station inactivity settings ...................................................................................... ...........57

Setting Device Properties ............................................................. ...................................................58

OSD Command Line Operations.....................................................................................................61

Accessing the Command Line...................................................................................................62

Resetting the keyboard and mouse ...........................................................................................62

Table of Contents v

Disabling Auto User Login.......................................................................................................63

Equalization tuning...................................................................................................................63

Deskew tuning...........................................................................................................................64

Configuring the DDC table ......................................................................................................65

Forcing a Connection to a Target Device .......................................................................................65

Forcing a connection using the OSD Command Line..............................................................66

Forcing a connection from the serial port to a target device...................................................67

Forcing a connection using SNMP...........................................................................................69

Chapter 4: Terminal Operations ................................................................................... 71

Accessing the Terminal Menu ..........................................................................................................71

Terminal Applications menu commands...................................................................................71

Appendices..................................................................................................................... 75

Appendix A: Technical Specifications .............................................................................................75

Appendix B: Using AMIQ-SRL Modules .........................................................................................85

Appendix C: OSCAR Interface Edit Device Screen Settings...........................................................90

Appendix D: Pod Switch Mode........................................................................................................93

Appendix E: Troubleshooting..........................................................................................................97

Appendix F: Command Functions.................................................................................................100

Appendix G: Technical Support.....................................................................................................103

Index.............................................................................................................................. 105

vi AMX Switch Series Installer/User Guide

LIST OF FIGURES

List of Figures

Figure 1.1: Typical AMX Switching System Configuration ..............................................................5

Figure 2.2: AMX Switching System Configuration with AMIQ and AMIQ-SRL Modules..............10

Figure 2.3: AMX Switching System Configuration with AMIQDM Modules..................................11

Figure 2.4: AMX Switching System Configuration with Redundancy.............................................12

Figure 2.5: AMX Switch Rack Mounting Diagram .........................................................................13

Figure 2.6: Example of an AMX Switch Back Panel (AMX 5020 Switch Shown)...........................14

Figure 2.7: Connecting Target Devices to an AMX Switch (AMX 5000 Switch Shown) ................16

Figure 2.8: Connecting Users to an AMX Switch ........................................................................... 17

Figure 2.9: Connecting a User Station for Switch Redundancy......................................................20

Figure 2.10: AMIQDM Module Dual Port Connectivity ................................................................21

Figure 2.11: Cascaded AMX Switching System, Blocking Configuration ......................................23

Figure 2.12: Cascaded AMX Switching System, Combination of Configurations ..........................24

Figure 2.13: AMX Switching System in a Broadcast Environment (AMX 5000 Switches and AMX

5121 User Stations Shown) ..............................................................................................................28

Figure 2.14: AMX Switch LEDs (AMX 5000 Switch Shown)..........................................................29

Figure 2.15: AMX User Station Front Panel ..................................................................................30

Figure 2.16: AMX User Station Back Panel (AMX 5111 User Station Shown)..............................31

Figure 2.17: IQ Modules with LEDs (AMIQDM Module Shown) ..................................................31

Figure 3.1: Example of the OSCAR Interface .................................................................................33

Figure 3.2: Server Hotkey Screen....................................................................................................36

Figure 3.3: Change Hotkey Screen..................................................................................................37

Figure 3.4: Configure Screen..........................................................................................................38

Figure 3.5: Configure Screen..........................................................................................................38

Figure 3.6: Target Flag Screen................................................................................... ....................39

Figure 3.7: Set Position Screen.............................................................................. .........................40

Figure 3.8: Information Screen.......................................................................................................41

Figure 3.9: Target Screen........................................................... .....................................................41

Figure 3.10: User Screen.................................................................................................................42

Figure 3.11: User Screen.................................................................................................................43

Figure 3.12: User Admin Screen.....................................................................................................44

Figure 3.13: Add User Screen.........................................................................................................45

vii

viii AMX Switch Series Installer/User Guide

Figure 3.14: Edit User Screen - Normal User.................................................................................46

Figure 3.15: User Rights Screen ..................................................................................................... 46

Figure 3.16: Edit User Screen - Admin User ..................................................................................47

Figure 3.17: Configure Screen........................................................................................................49

Figure 3.18: Console Screen...........................................................................................................50

Figure 3.19: Audio/Serial Screen (User Tab) .................................................................................53

Figure 3.20: Audio/Serial Screen (Admin Tab)..................................... ..........................................54

Figure 3.21: Information Screen .....................................................................................................55

Figure 3.22: Status Screen...............................................................................................................55

Figure 3.23: Lockdown Screen (Settings for the AMX 5130 User Station Shown).........................56

Figure 3.24: Redundancy Screen.....................................................................................................57

Figure 3.25: Inactivity Screen .........................................................................................................58

Figure 3.26: Device Admin Screen..................................................................................................59

Figure 3.27: Edit Device Screen (Normal Configuration)..............................................................59

Figure 3.28: Edit Device Screen (Seamless Configuration)............................................................61

Figure 3.29: Command Line Screen................................................................................................61

Figure 3.30: Configure Screen........................................................................................................62

Figure 3.31: Equalization Tuning Screen........................................................................................63

Figure 3.32: Deskew Tuning Screen................................................................................................64

Figure 1.1: AMX Switching System Configuration for Pod Switch Mode .......................................94

Figure 1.2: Example of a Pod Switch Mode Command at the Command Line...............................95

LIST OF TABLES

List of Tables

Table 3.1: Available Keyboard Layouts on the AMX User Station................................ .................48

Table 3.2: Available Keyboard Layouts on USB and Sun IQ Modules...........................................49

Table 3.3: PS/2 Keyboard to Sun Server .............................................. ..........................................51

Table 3.4: Power/Sleep for USB Servers.........................................................................................52

Table 3.5: OSD Command Line Hotkey Sequences ........................................................................62

Table 3.6: Force Connect Confirmation Codes...............................................................................68

Table 3.7: Force Disconnect Confirmation Codes..........................................................................69

Table 4.1: AMX Switching System Configuration ID ......................................................................72

Table 4.2: AMX System MIB Object Groups.................................................... ...............................74

Table 4.3: AMX System MIB Trap Files....................................... ...................................................74

Table 1.1: AMX 5000 Switch Specifications....................................................................................75

Table 1.2: AMX 5010 Switch Specifications....................................................................................76

Table 1.3: AMX 5020 Switch Specifications....................................................................................77

Table 1.4: AMX 5030 Switch Specifications....................................................................................78

Table 1.5: AMX 5130 User Station Specifications ..........................................................................79

Table 1.6: AMX 5111 and AMX 5121 User Station Specifications.................................................80

Table 1.7: AMIQ Module Specifications ........................................................................... ..............81

Table 1.8: AMIQDM Module Specifications......................................... ..........................................82

Table 1.9: AMIQ-SRL Module Specifications .................................................................................83

Table 1.10: History Mode Control Keys .........................................................................................88

Table 1.11: AMIQ-SRL Module Pinouts..........................................................................................88

Table 1.12: AutoView KVM Switch ................................................................................................90

Table 1.13: AutoView 200, 400, 416 or 424 Switch . .......................................................................90

Table 1.14: SwitchView OSD Switch...............................................................................................90

Table 1.15: AV2000R, AV1000R, AV2000 or DSR Switch......................................................... .....90

Table 1.16: OutLook ES Switch.......................................................................................................91

Table 1.17: XP Switch .....................................................................................................................91

x AMX Switch Series Installer/User Guide

Table 1.18: IBM C2T.......................................................................................................................91

Table 1.19: KVM Switch..................................................................................................................92

Table 1.20: Pod Switch Mode Commands.......................................................................................95

Table F.1: Access Commands ........................................................................................................100

CHAPTER

The Avocent AMX® switch is a KVM (keyboard, video and mouse) switch that allows users to access multiple system servers or serial devices from a single keyboard, monitor and mouse. Multiple users in different locations can share access to PC, USB or Sun servers and serial devices.

A typical AMX switching system consists of one or m Avocent matrix intelligent (IQ) modules. Up to three tiers of AMX switches can be cascaded to provide seamless access to a large number of target devices. Other KVM switches, including Avocent and non-Avocent branded, may also be attached in a cascaded system but do not provide seamless cascading.

All AMX switches are rack mountable and are equipped with the Avocent patented OSCAR graphical user interface and the AMWorks

Product Overview

Java™-based system administration tool.

ore AMX switches, user stations and

Features and Benefits

Internet Protocol (IP) support

The AMX switch series supports IPv4 (default) and IPv6 functionality.

Multiplatform

With the AMX switching system, you can access any combination serial devices using a single keyboard and mouse.

Connection sharing

Two or more users can share access to the same target device simultaneously through switch. When sharing a connection to a target device, all users see the video but only one user at a time controls the keyboard and mouse.

Security

The AMX KVM switching system allows you to house valuable equipment in controlled areas. IQ modules, compact devices that eliminate cable bulk, prevent device through cable manipulation. You can control user access by assigning rights to each username for specific target devices. Administrative privileges, usernames and the serial port are also password-protected.

of PC, USB

unauthorized access to a target

or Sun servers and

the AMX

2 AMX Switch Series Installer/User Guide

LDAP user authentication

The AMX switch supports the LDAP (Lightweight Director

y Access Protocol) user authentication mode. LDAP provides the Active Directory for username and password authentication. LDAP Matrix auth

entication will be enabled if your AMX switch supports LDAP.

Advanced video compensation

The AMX user stations and IQ modules provide advanced vide

o compensation that automatically maximizes video quality for long distance communications. You can also manually adjust video quality for specific servers or user stations.

Scalable architecture

The AMX switching system scalable architecture can easily accommodate additional servers

and users. IQ modules, user stations and switches are pre-assigned unique identification numbers (UIDs), allowing you to easily reconfigure the switching system. Name changes to IQ modules are automatically sent to all attached user stations, even if the units are on different networks.

Audio and serial support

You can use the AMX switching system to access audio and s

erial data from connected target devices. To access this feature, the AMX switching system must include multimedia-capable devices and a user station and IQ module that support audio and serial emulation.

Extended keyboard and mouse support

You can use a variety of keyboards and mouse peripherals

to access any target device in the AMX switching system. Most user stations support PS/2 and USB keyboard and mouse types. Some user stations support PS/2 multimedia keyboards. Pinnacle FAK (Fast Action Keyboard) and Chyron Duet keyboards are supported on AMX 5120, AMX 5121 and AMX 5130 user stations, and Devlin Vizrt keyboard is supported on AMX 5111, AMX 5121 and AMX 5130 user stations.

Broadcast configurations with nVision router control In AMX switching system broadcast configurations, stud

io operators can use Pinnacle FAK or Chryon keyboards and have access to Deko, Chyron CG and other machines used for delivery of live content. Editing suites have access to Avid, SGI and storage machines with full media provided from these machines through an AMX switch and nVision router combination. Broadcast engineers have full access to all servers and equipment to provide maintenance and support. In addition, all valuable equipment is secure and housed in a safe environment.

Connecting an nVision router to the AMX switching system provides video and audio ro uting functio

nality to users. When a user in the AMX switching system connects to a target device, the nVision router will automatically connect the audio and video signals from the target device to the user’s workstation.

Seamless cascading

Chapter 1: Product Overview 3

You can increase the number of target devices that us switching system. You can connect target devices to up to three levels of AMX or non-Avocent KVM switches. When cascading AMX switches, you can seamlessly connect to any target device from a single list in the OSCAR interface, as if all the target devices were connected to one switch. You can also cascade non-Avocent KVM switches, but to access the attached target devices you must first select the non-Avocent switch from the OSCAR interface target list, and then connect to the target device using the methods provided by the non-Avocent KVM switch.

Redundancy and scalability

You may connect two AMX matrix switches to a single user station to allow redundancy and fault tole

rance. If one of the AMX switches has a power failure, the second switch provides an alternate path to access the same set of target servers. In addition, you can extend your user station access to additional target servers connected to a second AMX switch.

OSCAR graphical user interface

With the OSCAR graphical user interface, you can use your keyboard or attached target device. This easy-to-use, menu-driven interface also enables you to administer security settings, language and keyboard selection, hotkey sequences and other features.

Administration using the AMWorks software

The AMWorks Java-based system ad switch. Use it to assign names to attached target devices and users, designate user access rights, monitor switching system events, and upgrade firmware. You can also use AMWorks software to configure AMX switching system installations remotely, eliminating the need to configure each unit separately.

ministration software tool is supplied with each AMX

ers can access by creating a cascaded

mouse to select any

System monitoring using the SNMP interface

The AMX switch supports the Simple Network Management Protocol (SNMP) to remotely monitor the switch via the protocol to manage and control user stations and their connections in the switching system.

Glossary

The following terms are used throughout this documentation:

• Cascading – Connecting multiple KVM switches to an AMX switch, providing additional

• Console – The user station and peripheral devices used by each local user

• IQ module – T

Ethernet port. Once SNMP is configured, you can use the SNMP

connections for tar connected to the AMX switching system.

PS/2, Sun or USB server) and the provide keyboard emulation, DDC (Digital Data Channel) and

get devices. Cascading expands the number of target devices that can be

he primary interface between an attached device (KVM switch, serial device or

AMX

switching system. IQ modules are server-powered and

AMX

switching system support.

4 AMX Switch Series Installer/User Guide

• Peripheral devices – The set of communication devices connected to each user station. May

include keyboard, monitor, mouse, speakers and headphones.

• Switch – Equipment that provides KVM connectivity to attached tar

• Switching system – A set of switches and attached target devices, user stations, IQ modules

and peripheral dev

• Target device – Equipment such as a server or serial device that is

module to a switch or user station and can be accessed through the switching system.

• Unit – Includes switches, user stations and target devices

is referring to any or all.

• User station – The interface between the AMX switch and system users,

settings and providing connections for peripheral devices. The user station also provides the OSCAR interface for target device selection and administration.

ices.

Component Overview

An AMX switching system typically consists of four main components:

• One or more AMX switches.

• One or more Avocent AMX matrix user stations.

• One or more Avocent IQ modules, available in several different types including the AMIQ,

AMIQDM and AMIQ-SRL modules.

•

Unshielded Twisted Pair (UTP) cables.

A typical AMX switching system configuration is illustrated in Figure 1.1.

get devices.

attached through an IQ

; this term is used when the procedure

storing local (console)

Chapter 1: Product Overview 5

AMX Switch

UTP Cables

64 Servers

Module

User Station

16 Users

Figure 1.1: Typical AMX Switching System Configuration

The AMX switch

The AMX switch provides the framework for the AMX switching system and is available in a variety of matrix sizes. Each AMX switch can be cascaded to create larger system configurations. The AMX switch stores a full database of user rights and server names and communicates with the AMWorks software through an IP (Internet Protocol) port. IPv4 and IPv6 modes are supported.

The AMX user station

The AMX user station, the interface between the AMX switch and system users, stores local (console) settings and provides connections for peripheral devices. The user station also provides the OSCAR interface for target device selection and administration.

6 AMX Switch Series Installer/User Guide

The AMX switch IQ modules

The IQ module is the primary interface between an attached device (KVM switch, serial device or PS/2, Sun or USB server) and the AMX switching system. If the switch loses power, the target devices will continue to power the IQ modules. This Keep Alive functionality ensures continued keyboard and mouse operability and prevents data loss. Available in three types, IQ modules also provide keyboard emulation, DDC (Digital Data Channel), and AMX switching system support.

• AMIQ module – a standard IQ module that connects a target device to the switching system.

AMIQ modules are available for PS/2, USB and Sun VGA or 13W3 interfaces.

•

AMIQDM module –a two-port IQ module that enables one server to be shared between two AMX switches, incre AMIQDM module also enables the multimedia feature (audio and serial data communication) when it is connected to a user station that supports th is feature. AMIQDM modu les are available as PS/2, USB and Sun VGA interface modules.

• AMIQ-SRL (serial) module – a DCE (Data Communication Equipment) device that is the

primary interface be terminal emulation, break suppression and port history. See Appendix B: Using AMIQ-SRL Modules on

IQ modules are connected additional cables or extra rack spaces. Each IQ module has a factory-assigned unique number that identifies the attached target device within the system.

page 85

asing the number of users that can be added to the switching system. The

tween a serial device and the AMX switching system. It supports VT100

for more information.

to the switching system with UTP cabling and eliminate the need for

UTP cables

You may use any combination of CAT 5, CAT 5e and CAT 6 cables in the AMX switching system.

NOTE: Throughout this manual, UTP refers to any CAT cable used by the AMX switching system.

Safety Precautions

To avoid potential video and/or keyboard problems when using Avocent products:

• If the building has 3-phase AC power,

For best results, they should be on the same circuit.

To avoid potentially fatal shock hazard and possible damage to equipment, please observe the following precautions:

Do not use a 2-wire extension cord in any Avocent product configuration.

•

• Test AC outlets at the server and monitor for proper polarity and grounding.

• Use only with grounded outlets at both the server and monitor. When using a backup

Uninterruptible Power Supply (UPS), power the server, the monitor and the AMX switch off the supply.

NOTE: The AC inlet is the main disconnect.

DC installation safety considerations

As a safety precaution, install this product in an area with limited or controlled access. A readily accessible disconnect device that is suitably approved and rated shall be incorporated in the field wiring. Connect field wiring from earth ground to the screw terminal marked with the ground symbol. Terminals will accommodate wiring from 26 to 12 AWG (up to 2.5 mm2 maximum cross section). Strip each wire, insert it in the square opening in the terminal block and tighten the screw above it to a maximum of 70 ounce-inches (0.5 Nm) using either a flat or Phillips-head screwdriver.

Chapter 1: Product Overview 7

ensure that the server and monitor are on the same phase.

Rack mount safety considerations

• Elevated Ambient Temperature: If installed in a clos

temperature of the rack environment may be greater than room ambient. Use care not to exceed the rated maximum ambient temperature of the unit.

• Reduced Air Flow: Installation of the equipment in a rack should be such that the amount of

low required for safe operation of the equipment is not compromised.

airf

• Mechanical Loading: Mounting of the equipment in the rack should be

condition is not achieved due to uneven mechanical loading.

• Circuit Overloading: Consideration

supply circuit and the effect that overloading of circuits might have on overcurrent protection and supply wiring. Consider equipment nameplate ratings for maximum current.

• Reliable Earthing: Reliable earthing of rack mo

particular attention to supply connections other than direct connections to the branch circuit (for example, use of power strips).

should be given to the connection of the equipment to the

ed rack assembly, the operation

such that a hazardous

unted equipment should be maintained. Pay

8 AMX Switch Series Installer/User Guide

CHAPTER

Installation

AMX Switching Systems

AMX switching systems consist of an AMX switch or switches, user stations, target devices, IQ modules and peripheral devices. See Figure 2.2 on page 10 and Figure 2.3 on page 11 examples of switching system configurations.

Getting Started

Before installing your AMX switching system, make sure you have access to the following items:

• The AMX switch and all of the items supplied with it. These items

rack mounting brackets, a null modem cable, installation CDs and help materials.

• At least one user station for connecting to the AMX switch.

• UTP cables for each target device and user station you plan

• One AMIQ or AMIQDM module for each server and one AMIQ-SRL

serial device.

• AMWorks software, available by free download at www.avocent.com/support or on the

lation CD included with the AMX switch.

instal

may include a power cord,

to attach to the switching system.

module for each

10 AMX Switch Series Installer/User Guide

Figure 2.2 illustrates one possible switching system configuration using AMIQ and AMIQ-SRL modules.

Local PC

AMX Switch (AMX 5000 Switch Shown)

Target Devices

AMIQ Module

(PS/2 Shown)

AMX User Station (AMX 5130 User Station Shown)

Server with AMWorks Software

AMIQ-SRL Module

Serial Device

USB Keyboard

Serial Port

Stereo Speakers

Monitor

Figure 2.2: AMX Switching System Configuration with AMIQ and AMIQ-SRL Modules

and Microphone

and Mouse

Chapter 2: Installation 11

Figure 2.3 illustrates another possible switching system configuration using AMIQD M modules, specialized IQ modules with dual port connectivity and audio and serial connections.

Server with AMWorks Software

AMX Switch (AMX 5000 Switch Shown)

Target Devices

AMIQDM Module (PS/2 Shown)

Local Server

Monitor

Figure 2.3: AMX Switching System Configuration with AMIQDM Modules

AMX User Station (AMX 5130 User Station Shown)

Serial Port

Stereo Speakers and Microphone

USB Keyboard and Mouse

12 AMX Switch Series Installer/User Guide

Figure 2.4 illustrates a switching system configuration where two AMX switches are connected to a single user station, and target servers are connected to both swit utilizing this connection method, you may benefit from switch redundancy in the event of a single switch failover.

Network

ches using AMIQDM modules. By

AMX Switch (AMX 5000 Switch Shown)

Server Ports

AMX User Station (AMX 5130 User Station Shown)

AMIQDM Module

Server with AMWorks Software

USB Keyboard and Mouse

Monitor

AMX Switch (AMX 5000 Switch Shown)

Server Ports

Figure 2.4: AMX Switching System Configuration with Redundancy

Target Server

Rack Mounting an AMX Switch

A rack mounting kit is supplied with each AMX switch. You may either place the AMX switch on the rack shelf or mount the switch directly into an Electronic Industries Alliance (EIA) standard

CAUTION: Rack Loading - Overloading or uneven loading of racks may result in shelf or rack failure, causing damage to equipment and possible personal injury. Stabilize racks in a permanent location before loading begins. Mount components beginning at the bottom of the rack, then work to the top. Do not exceed your rack load rating.

CAUTION: Power Considerations - Connect only to the power source specified on the unit. When multiple electrical components are installed in a rack, ensure that the total component power ratings do not exceed circuit capabilities. Overloaded power sources and extension cords present fire and shock hazards.

To install the rack mounting bracket:

1. Remove the two rack mounting screws from each side of the AMX switch.

2. Place the rack mounting brackets next to the switch

3. Insert the screws supplied with the rack mounting kit through the holes of the brackets and into

Install the AMX switch into the rack using the approved method of the rack manufacturer.

rack.

the AMX switch. T

ighten the screws securely.

Chapter 2: Installation 13

as illustrated in Figure 2.5.

Figure 2.5: AMX Switch Rack Mounting Diagram

Installing an AMX Switch

To install a new AMX switch, you will connect power sources, configure network settings and connect the switch to the local area network (LAN).

NOTE: Turn off the AMX switch and disconnect the power cord from the AC outlet before servicing.

14 AMX Switch Series Installer/User Guide

Network Port

Figure 2.6: Example of an AMX Switch Back Panel (AMX 5020 Switch Shown)

CAUTION: To reduce the risk of electric shock or damage to your equipment -

- Do not disable the power cord grounding plug . The groun ding p lug is an impo rt ant safety featu re.

- Plug the power cord into a grounded (earthed) outlet that is easily accessible at all times.

- Disconnect the power from the unit by unplugging the power cord from either the electrical outlet or the unit.

User Ports

Server Ports

To connect power sources:

Attach one end of the supplied power cord into the back panel of

the AMX switch and attach the

other end to an AC power source.

To configure network settings for the switch:

1. Use the supplied modem cable to connect a terminal or PC running terminal emulation

software (su

ch as HyperTerminal

) to the labeled terminal port of the AMX switch. The

terminal should be set to 9600 baud, 8 bits, 1 stop bit, no parity and no flow control.

2. Power up the AMX switch.

The Power indicator on the front of the switch will remain orange for approximately 30 seconds while performing a self-test and then change to green. This indicates a healthy condition.

3. When you first access the switch, you will be prompted through the Terminal window to enter

ername.

a us a. Enter the username

admin. By default, a password is not required. Once you have access

to the AMX switch terminal applications menu, you can change the default username and password for the serial port. For more information see Set/Change Password on page 72.

b. Press

Enter.

4. The AMX switch Console menu will open automatically. Select option 1,

Network Con

figuration.

a. Select option 1 to set the IP address. b. Select option 2 to set your netmask. c. Select option 3 to set your default gateway.

5. Type

0 to return to the AMX switch Console menu.

6. Complete one of the following steps to set the configurati on ID for the AMX switch.

Chapter 2: Installation 15

NOTE: Configuration ID can only be used in IPv4 mode.

• If all AMX switches in your installation are part of the same AMX switching system configuration, leave the configuration ID set to

• If you are running more than one A

MX switching system configuration within your subnet,

00000.

designate the group to which this AMX switch belongs. Select option 2 and en ter th e configuration ID for your AMX switch. A configuration ID wi ll designate an AMX switch as part of a unique installation. When change commands are issued through the AMWorks software, only units with the same configuration ID as the AMWorks software will be affected. Refer to

To set the IP mode: on page 72 for more information on setting

configuration IDs.

7. Type

0 to return to the AMX switch Console menu.

8. Select option 3 and follow the prompts to password protect your AMX switching system terminal settings.

CAUTION: This password places your AMX switch terminal in a secure mode. This password should be guarded like any network password and care should be taken to avoid forgetting or misplacing it. This password cannot be reset or recovered if lost or forgotten. Should you lose your password, please contact Avocent Technical Support for assistance.

9. Type 0 to exit the AMX switching system Console menu.

You can configure other switch settings using the Terminal Applications menu. Refer to Chapter 4 beginning on page 71 for more details.

To connect the AMX switch to the LAN:

Attach a UTP cable to the Network port on the back panel of the

AMX switch and connect the

switch to the LAN.

Connecting Target Devices to the AMX Switch

Once the AMX switch is installed, attach servers or serial devices to the switch using IQ modules. Figure 2.7 on page 16 illustrates how to connect target devices to the switching system.

To connect servers to the AMX switching system:

1. Choose an appropriate IQ module and insert the connectors into the corresponding ports on the back of the s

Some IQ modules provide audio and serial connectors, which may be left unattached if this functio

2. Attach one end of a UTP cable into the RJ-45 port on the IQ module. Attach the other end of the cable to an RJ-45

erver.

nality is not required for the switching system.

server port on the AMX switch.

16 AMX Switch Series Installer/User Guide

AMX Switch (AMX 5000 Switch Shown)

UTP Cable

AMIQ Module (PS/2 Shown)

Server Ports

Target Devices

Target Device

Figure 2.7: Connecting Target Devices to an AMX Switch (AMX 5000 Switch Shown)

3. For future reference, note the unique identifier (UID) on the back of the IQ module and the target device to which it is attached.

4. Repeat this procedure for every se

rver that will be attached to the AMX switching system.

To connect serial devices to the AMX switching system:

NOTE: The AMIQ-SRL module is a DCE device and only supports VT100 terminal emulation.

1. Attach the AMIQ-SRL module to the serial port of the device to be attached.

2. Attach one end of a UTP cable to the RJ-45 connector on the AMIQ-SRL module. Attach the othe

r end of the cable to an RJ-45 server port on the back panel of the AMX switch.

Attach

the power supply to the power connector on the AMIQ-SRL module. Up to four AMIQ-

SRL modules can be powered from a single power supply.

4. Attach the AMIQ-SRL module power supply to an AC wall outlet.

Repeat this procedure for every serial device

that will be attached to the AMX switching system.

See Using AMIQ-SRL Modules on page 85 for more information about using AMIQ-SRL modules.

Connecting Users to the AMX Switching System

Once all target devices are attached, add users by attaching user stations and peripheral devices to the AMX switching system. Figure 2.8 illustrates how to connect users to the s

AMX Switch (AMX 5000 Switch Shown)

Target Server Ports

UTP Cable

AMIQDM Module (PS/2 Shown)

Chapter 2: Installation 17

witching system.

Local Server

Monitor

Figure 2.8: Connecting Users to an AMX Switch

AMX User Station (AMX 5130 User Station Shown)

PS/2 Mouse and Keyboard Ports

USB Keyboard and Mouse

Serial Port

Stereo Speakers and Microphone

Supported keyboard and mouse types

To determine what keyboard and mouse types your us

er station supports, examine the available

ports on the back panel of the user station. USB and PS/2 ports are designated by symbols as shown

18 AMX Switch Series Installer/User Guide

in Figure 2.8. If an appropriate port is available, the keyboard or mouse type is supported by the user station.

Specialized keyboards such as Pinnacle FAK, Chyr connected through the PS/2 port. The Pinnacle FAK and Chyron Duet keyboards, if supported on your user station, may be selected through the OSCAR interface. Devlin Vizrt keyboards do not require any special configuration settings and is not available as a selectable option in the OSCAR interface. For more information on whether your user station supports one of these specialized keyboards, please see

To connect users to the AMX switching system:

Extended keyboard and mouse support on page 2.

on Duet and Devlin Vizrt keyboards are

1. Place the AMX user station near the monitor. The user station can be used as Attach peripheral devices to the corresponding ports on the back

3. Attach one end of a UTP cable into an RJ-45 port on the the cable to an RJ-45 user port on the AMX switch.

4. Attach one end of the supplied power cord to the power socket on the back panel of the user station and attach

To set the keyboard type:

If you attached a Pinnacle FAK or Chyron following steps to activate the keyboard in the OSCAR interface:

1. Press

2. Click the Console tab, then

3. Select the appropriate keyboard type from the Type drop-dow

4. Click Apply.

Ctrl+Ctrl to launch the OSCAR interface.

only allows you to select keyboard types supported by the attached user station.

If you connected a Pinnacle FAK keyboard, complete the following steps: a. Click the Admin tab b. Select the target device that will c. Click Edit device. d. Select Pinnacle FAK from

emulation mode if the device type is PS/2. (If you are using a Chyron Duet keyboard, the

Emulation mode should be Standard.) e. Click Apply. Close the OSCAR interface.

the other end to an AC wall outlet.

Duet keyboard to the user station, complete the

click the down arrow button to display the Configure screen.

be running software that requires Pinnacle FAK support.

the Emulation drop-down menu. You can only edit the

panel of the user station.

user station. Attach the other end of

n menu. The drop-down menu

a monitor stand.

Connecting a Local Server to the AMX Switching System

After all user stations are connected to the AMX switching system, you can attach a local server. The local server can be accessed from the user station to which it is attached, but not by other users

+ 218 hidden pages

Avocent 590-222-501M User Manual

AMX® Switch Series

TABLE OF CONTENTS

LIST OF FIGURES

LIST OF TABLES

Product Overview

Glossary

Component Overview

The AMX switch

The AMX user station

The AMX switch IQ modules

UTP cables

Safety Precautions

Installation

AMX Switching Systems

Getting Started

Rack Mounting an AMX Switch

Installing an AMX Switch

Connecting Target Devices to the AMX Switch

Connecting Users to the AMX Switching System

Connecting a Local Server to the AMX Switching System