Top Load Washer Quick Start Guide
OPERATING INSTRUCTIONS
WARNING
Fire Hazard
Never place items in the washer that are dampened with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS, located in your appliance's Owner's Manual, before operating this appliance.
NOTES:
Not all features and cycles are on all models, and control panel appearance may vary.
If your model has a touch interface, the control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered, touch the control panel with your fingertip, not your fingernail. When selecting a setting or option, simply touch its name.
If your model has physical buttons, make sure to press the button firmly.
At cycle completion, your setting and option choices will be remembered for the next cycle. However, if power to the washer is lost, the settings and options will go back to the factory defaults.
Step 1. Add HE Detergent
NOTE: See the “Adding Laundry Products” section for more information on adding HE detergent, fabric softener, and/or bleach.
Step 2. Load Clothes
For best results, load garments in loose heaps evenly around basket wall.
Step 3. Select Cycle and Settings
Step 4. Press Start/Pause/Cancel/
Unlock Lid
Button Descriptions |
2 |
WATER LEVEL
Set the Water Level knob to the Auto Sensing setting and the washer will fill to a level that ensures the load engages the agitator. From this point, the electronic control will sense the load and determine if additional water is needed.
Set the Water Level knob to the Deep Water Wash setting and the washer will fill to the maximum water level.
Cycle Guide – Normal Cycle
For best fabric care, choose the cycle that best fits the load being washed. Recommended settings for best performance are shown in bold. Not all cycles and options are available on all models. Not all settings and options are available on each cycle.
Items to Wash: |
Cycle: |
Temperature: |
Description: |
Cottons, linens, and |
Normal |
Hot |
Use this cycle for normally soiled cottons |
mixed garment loads |
Regular |
Warm |
and mixed-fabric loads. This cycle has a |
|
|
Cool |
default of a high spin speed. |
|
|
Cold |
NOTE: Deep Water Wash is not available |
|
|
Tap Cold |
|
|
|
in the Normal Regular cycle mode. |
|
|
|
|
Selecting the Normal Regular cycle with the |
|
|
|
Deep Water Wash setting will result in auto |
|
|
|
sensing of the water level. |
|
|
|
|
Online Ordering Information
For detailed installation instruction and maintenance information, winter storage, and transportation tips, please see the Owner’s Manual included with your machine.
For information on any of the following items, the full cycle guide, detailed product dimensions, or for complete instructions for use and installation, please visit https://owners.amana.com/owners/, or in Canada http://amanacanada.ca/owners/. This may save you the cost of a service call.
However, if you need to contact us, use the information listed below for the appropriate region.
United States: |
Canada: |
1–866–616–2664 |
1–800–807–6777 |
Amana Brand Home Appliances |
Amana Brand Home Appliances |
Customer eXperience Center |
Customer eXperience Centre |
553 Benson Road |
200–6750 Century Ave. |
Benton Harbor, MI 49022–2692 |
Mississauga, Ontario L5N 0B7 |
NOTES:
Cycle times will be longer due to extended fill times when using the Deep Water Wash setting.
Deep Water Wash settings are not available in the Normal Regular cycle mode. Selecting the Normal Regular cycle with a Deep Water Wash setting will result in auto sensing of the water level.
WASH TEMPERATURE
Wash Temperature senses and maintains uniform water temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric and soils being washed. For best results and following the garment label instructions, use the warmest wash water safe for your fabric.
NOTES:
On some models and cycles, warm and hot water may be cooler than your previous washer.
Even in a coldor cool-water wash, some warm water may be added to the washer to maintain a minimum temperature. All rinses are cold.
WASH CYCLE KNOB
Use the Wash Cycle knob to select available cycles on your washer. Turn the knob to select a cycle for your laundry load. See online “Cycle Guide” for detailed descriptions.
START/PAUSE/UNLOCK LID BUTTON
Press to start the selected cycle; press again to pause the cycle and unlock the lid.
NOTE: If the washer is spinning, it may take several minutes to unlock the lid. Press and hold for 3 seconds to cancel a cycle.
CYCLE STATUS
The Cycle Status lights show the progress of a cycle. At each stage of the process, you may notice sounds or pauses that are different from your previous washer.
Sensing/Fill
When the Start/Pause/Unlock Lid button is pressed, and the Water Level knob is set to Auto Sensing, the washer will fill and begin sensing to determine load size and balance.
Once sensing is complete, the washer will fill to the appropriate level for the detected load size and then begin the wash phase of the cycle.
NOTE: Sensing and wash phases will be paused by opening the unlocked lid. Close the lid to resume the cycle. If the lid is left open for more than 10 minutes, the washer will cancel the cycle and pump out the water. The lid will lock after the wash phase to begin the initial spinout and remain locked for the remainder of the cycle.
Wash
The washer will fill to the correct water level based on the load size and the Water Level selection. Certain cycles may agitate during the fill process to boost cleaning. You will hear the agitator rotate, followed by a pause lasting several seconds. When the wash cycle begins, you will hear the agitator increase speed. The motor sounds may change at different stages in the wash cycle while the washer performs different wash actions.
Designed to use only HE
High Efficiency detergents.
Rinse
Certain cycles use a spray rinse, which adds water to the tub while the basket spins. You may hear sounds similar to the wash cycle as the washer rinses and moves the load. You may hear the motor turning on briefly (short hum) to move the basket while filling.
Final Spin
The washer spins the load at increasing speeds for proper water removal, based on the selected cycle.
Cycle Complete
Once the cycle is complete, the lid will unlock and this light will come on. Remove the load promptly for best results.
Lid Locked
The lock feature allows for higher spin speeds. When the Lid Locked light is lit, the lid is locked and cannot be opened without pausing the cycle. When the light is off, the lid can be opened.
To open the lid after it has been locked, press Start/Pause/Unlock Lid. The lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at a high speed. Press Start/ Pause/Unlock Lid again to resume the cycle.
Adding Laundry Products
IMPORTANT: Using non-HE detergent will likely result in longer cycle times and reduced rinsing performance. It may also result in component malfunction and, over time, buildup of mold or mildew. HE detergents should be lowsudsing and quick-dispersing to produce the right amount of suds for the best performance.
Adding HE detergent to basket:
Add a measured amount of HE detergent or single-dose laundry packets into the basket. If using Oxi-type boosters, color-safe bleach, or fabric softener crystals, add to the bottom of the washer basket before adding clothes.
NOTE: Follow the manufacturer’s instructions to determine the amount of laundry products to use.
Adding liquid chlorine bleach:
Do not overfill, dilute, or use more than 1 cup (236 mL). Do not use color-safe bleach or Oxi products in the same cycle with liquid chlorine bleach.
NOTE: Follow the manufacturer’s instructions to determine the amount of laundry products to use.
IMPORTANT: You must set the Water Level knob to Auto Sensing + Extra Rinse with Fabric Softener, or Deep Water Wash + Extra Rinse with Fabric Softener to ensure proper distribution of the fabric softener during the final rinse portion of the cycle.
On models with a fabric softener dispenser:
Pour a measured amount of liquid fabric softener into dispenser; always follow manufacturer’s directions for the correct amount of fabric softener based on your load size. Dilute liquid fabric softener by filling the dispenser with warm water until liquid reaches the underside of the rim. See “Max Fill” line arrows.
On models without a fabric softener dispenser:
During the final rinse, wait until the washer has completed filling, then press Start/Pause/Unlock Lid to pause the washer. Lift the lid and add the measured recommended amount of liquid fabric softener to the load. Do not use more than the recommended amount. Close the lid and press Start/Pause/Unlock Lid again to start the washer.
W11354639A |
®/™ ©2019 All rights reserved. Used under license in Canada. |
W11354873A–SP |
|
Loading...