Actron CP9125 User Manual

CP9125

OBD II PocketScan

Code Reader

For use with OBD II Compliant Vehicles

LCD Display - Is a Single Line Display with 8 characters.

ERASE Key - Used to Erase Trouble Codes and I/M

Monitor status from Vehicles Computer Modules and scroll up through screens. (I/M Monitors are currently

used for state emissions tests.)

READ/Scroll Down Key - Used to view Read Codes, MIL

Status, I/M Readiness Status and Scroll down through screens.

OBD II Connector - Used to communicate with OBD II

compliant vehicles.

0002-002-2666

Safety Precautions

For safety, read, understand and follow all safety messages and instructions in manual before operating the PocketScan Code Reader.

Always refer to and follow safety messages and test procedures provided by manufacturer of vehicle and PocketScanTM Code Reader.

Signal Words Used:

DANGER

WARNING

CAUTION

IMPORTANT

Important Safety Messages

 Always wear ANSI approved eye protection.

 Always operate vehicle in a well-ventilated area.

 Always keep people, tools and test equipment away from all

moving or hot engine parts.

 Always make sure vehicle is in PARK (automatic

transmission) or Neutral (manual transmission) and parking brake is set.

 Always block drive wheels and never leave vehicle

unattended while testing.

 Always keep a fire extinguisher suitable for gasoline/

electrical/chemical fires readily available.

 Never lay tools on vehicle battery.

Indicates a possible hazardous situation which, if not avoided, will result in death or serious injury to operator or bystanders.

Indicates a possible hazardous situation which, if not avoided, could result in death or serious injury to operator or bystanders.

Indicates a possible hazardous situation which, if not avoided, may result in moderate or minor injury to operator or bystanders.

Indicates a condition which, if not avoided, may result in damage to test equipment or vehicle.

 Always use caution when working around ignition coil,

distributor cap, ignition wires, and spark plugs. Components can produce a High Voltage while engine is running.

 Battery acid is caustic. If contacted, rinse with water or

neutralize with a mild base (i.e. baking soda). If in eyes, flush with water and call a physician immediately.

 Never smoke or have open flames near vehicle. Vapors

from gasoline and battery during charge are explosive.

 Never use the PocketScanTM Code Reader if internal

circuitry has been exposed to moisture. Internal shorts could cause a fire and damage.

 Always turn ignition key OFF when connecting or

disconnecting electrical components, unless otherwise instructed.

 Some vehicles are equipped with safety air bags. Follow

vehicle service manual cautions when working around air bag components or wiring. Note, air bag can still open several minutes after ignition key is off.

 Always follow vehicle manufacturers warnings, cautions and

service procedures.

PocketScanTM Code Reader Features

Read Codes:

Reading Diagnostic Trouble Codes allows the PocketScan Code Reader to read the codes from the vehicles computer modules.

 Diagnostic Trouble Codes:

Diagnostic Trouble Codes are used to help determine the cause of a problem or problems with a vehicle. Diagnostic Trouble Codes are set when a fault is present for a sufficient amount of time.

P0443

 Pending Codes: Pending

Codes are also referred to as continuous monitor codes and maturing codes. Pending Codes occurs when the code has not occurred a specific number of times (depending on vehicle,) causing the code to mature.

P0452

MIL Conditions:

MIL (Malfunction Indicator Lamp) Status displays the state of the vehicles computer module(s).

 MIL ON: Indicates that the

Malfunction Indicator Lamp on vehicle should be ON indicating a possible emissions problem.

MIL ON

√ If the MIL Status is ON and the MIL is not illuminated with

the engine running, then a problem exists in the MIL circuit.

 MIL OFF: Indicates the

Malfunction Indicator Lamp should be off and there should be no emission problems.

MIL OFF

√ Some manufacturers will turn the MIL off if a certain

number of drive cycles occur without the same fault being detected.

√ Diagnostic Trouble Codes related to a MIL are erased

from the computers memory after 40 warm-up cycles if the same fault is not detected.

Inspection / Maintenance Monitors (I/M Monitors):

The I/M Monitors (Inspection / Maintenance) function displays a SNAPSHOT of the operations for the Emission System.

√ After a specific amount of drive time (each monitor has

specific driving conditions and time required), the computers monitors will decide if the vehicles emission system is working correctly.

√ Some states MAY NOT require all monitors listed to be

Ready to pass the emissions test. Check with state testing site for exact requirements. All states will fail a vehicle that has the MIL Light lit at time of test.

 Monitors Viewed:

Monitors Expanded Name

Misfire Misfire Monitor

Fuel Fuel System Monitor

Comp Comprehensive Components Monitor

Catlyst Catalyst Monitor

Htd Cat Heated Catalyst Monitor

Evap Evaporative System Monitor

Sec Air Secondary Air System Monitor

A/C Air Conditioning Refrigerant Monitor

O2 Snsr Oxygen Sensor Monitor

O2 Htr Oxygen Sensor Heater Monitor

EGR Exhaust Gas Recirculation

 Monitor Status:

Status Description

Ready

Vehicle was driven enough under proper conditions to complete the monitor. (Incomplete) - Vehicle was not driven enough under

Inc

proper conditions to complete the monitor.

 Monitors may be cleared by:

− Using the erase codes function.

− Disconnected or discharged battery (on some vehicles.)

− Computer module losing power (on some vehicles.)

Reading Diagnostic Trouble Codes and Data

WARNING

1.Turn Ignition Key to the Off Position.

2. Locate and Plug in Data Link Connector (DLC.)

NOTE: The data link connector

should be located under the dashboard on the driverside of the vehicle. If the data link connector is not located under the dashboard as stated, a label describing the location of the data link connector should be there.

3. Observe Display toggles between

Pocket and Scan.

NOTE: For a correct reading for

Diagnostic Trouble Codes and I/M Monitor Status, ignition key must be in the ON position and Engine does

not require starting.

Avoid Cooling Fan! Fan may turn on during test.

Pocket

To get a correct reading for MIL Status, Engine must be started.

4. Start Engine.

5. Press READ/Scroll Down Key

and Release.

NOTE: If diagnostic trouble codes (DTCs) are already being

displayed from a previous read operation, press and hold

READ/Scroll Down key for 3 seconds and release.

6.Observe a Moving * on Display.

NOTE: If a No Link message

displays, cycle ignition key to the OFF position for 10 seconds, then back ON and repeat Reading Diagnostic Data.

7. View Codes on Display

NOTE: If there are no codes present,

the tool will display 0 Codes and proceed to

display MIL Status when READ/Scroll Down is pressed.

 To View Codes press and

release READ/Scroll Down key.

 If the code is a Pending

Code a , will be displayed.

No Link

3 Codes9

0 Codes9

P0443

P0452

8. View MIL Status

 Press and release

READ/Scroll Down

key.

9. View I/M Monitors that are Incomplete.

 Press and release

MIL ON

Monitrs

READ/Scroll Down

key.

2 Inc

Misfire

NOTE: If there are no more I/M

Monitors that are Incomplete, the tool will then display Ready

Monitors when READ/Scroll Down key is pressed.

10. View I/M Monitors that are Ready.

 Press and release

READ/Scroll Down

key.

NOTE: Pressing the ERASE key will scroll up to review

Diagnostic Trouble Codes and Data.

NOTE: Holding READ /Scroll Down key for 3 seconds

will read Diagnostic Trouble Codes and Data again.

5 Ready

O2 Htr

Erasing Diagnostic Trouble Codes and Data

Erasing allows the PocketScanTM Code Reader to delete the codes and I/M Monitor status from the vehicles computer modules.

IMPORTANT

WARNING

1.Turn Ignition Key to the Off Position.

2. Locate and Plug in Data Link Connector (DLC.)

NOTE: The data link connector

3. Observe Display toggles between

Pocket and Scan.

Only Erase Diagnostic Data after checking system completely and writing down results.

Avoid Cooling Fan! Fan may turn on during test.

Scan

4.Turn Ignition Key to the ON Position leaving Engine Off.

NOTE: Make sure that the Ignition Key is

ON and NOT in the Accessory Position.

5.Press and Hold ERASE Key for 3 Seconds and Release.

6.Observe ERASE? Displays.

7.Press and Hold ERASE Key for 3 Seconds and Release.

ERASE?

8.Observe a Moving - on Display.

NOTE: If a NO LINK message

displays, cycle ignition key to the OFF position for 10 seconds, then back ON, and repeat Erasing Diagnostic Data.

9.Observe DONE Displays.

NO LINK

DONE

NOTE: If the problem causing Diagnostic Trouble Code(s) still

exists, the code will return. The Diagnostic Trouble Code may return immediately or may return after vehicle has been driven.

NOTE: Pressing READ /Scroll Down key will read

Diagnostic Trouble Codes and Data and Holding

ERASE key will erase results again.

Using Included CD

The Included CD is NOT required to use tool.

 Some items included on the CD are:

o Manual included with tool. o DTC Lookup Software. o Adobe Acrobat Reader.

 To be able to use the included CD the PC must

meet the following minimum requirements:

o 486 PC. o 4 MB of RAM. o Microsoft Windows 95 or Newer. o CD ROM Drive. o Adobe Acrobat Reader. o Internet Explorer 4.0 or Higher. o Minimum Screen Resolution of 800 x 600.

 If resolution is 800 x 600, in Display Properties,

Settings Tab, Set Font Size to Small Fonts.

Running Applications On Included CD

1. Close All Programs on Computer.

2. Place Included CD in CD-Drive.

NOTE: If CD does not start automatically;

Select the Start button. Select

Run...Enter X:\Menu.Exe in Open Box on Computer and select OK.

NOTE: X is the CD-ROM drive letter

on the computer.

3. Observe Menu Appears.

4. Follow screen prompts on computer to run applications.

Diagnostic Trouble Codes (DTCs)

This section contains the J2012 Diagnostic Trouble Codes (DTCs) as defined by the Society of Automotive Engineers (SAE). Diagnostic Trouble Codes (DTCs) are recommendations not a requirement. Manufacturers may not follow these, but most do.

Check vehicles service manual for DTC meaning if the code(s) you are getting does not make sense.

Diagnostic Trouble Code (DTCs) definitions have been assigned or reserved by the Society of Automotive Engineers (SAE) to direct to proper service area(s).

Codes not assigned or reserved by the Society of Automotive Engineers (SAE) are reserved for the manufacturer and referred to as Manufacturer Specific Diagnostic Trouble Codes (DTCs).

Remember:

 Visual inspections are important!  Problems with wiring and connectors are common,

especially for intermittent faults.

 Mechanical problems (vacuum leaks, binding or

sticking linkages, etc.) can make a good sensor look bad to the computer.

 Incorrect information from a sensor may cause the

computer to control the engine in the wrong way. Faulty engine operation might even make the computer show a known good sensor as being bad!

NOTE: Additional DTC definitions can be obtained from the CD

supplied. If there are any problems operating the supplied CD contact Customer Service at 1(800) 228-7667.

+ 30 hidden pages