3M B296423, B296424 User Manual

3M™ Scotch-Brite™ Products, Light Deburring Wheels, S FIN 05/19/15

Safety Data Sheet

Copyright,2015,3M Company.

All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:	26-2734-7	Version Number:	1.13
Issue Date:	05/19/15	Supercedes Date:	04/14/15

SECTION 1: Identification

1.1. Product identifier

3M™ Scotch-Brite™ Products, Light Deburring Wheels, S FIN

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3.Supplier’s details MANUFACTURER: 3M

DIVISION:	Abrasive Systems Division
ADDRESS:	3M Center, St. Paul, MN 55144-1000, USA
Telephone:	1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

2.3. Hazards not otherwise classified

None.

SECTION 3: Composition/information on ingredients

Ingredient

C.A.S. No.

% by Wt

__________________________________________________________________________________________

Page 1 of 10

3M™ Scotch-Brite™ Products, Light Deburring Wheels, S FIN 05/19/15

Silicon Carbide Mineral	409-21-2	35 - 50
Talc	14807-96-6	5	- 10
Lubricant	4485-12-5	0.5 -		5
Lubricant	Trade Secret*	0.1 -		0.5
Quartz Silica	14808-60-7	0.01 -		0.20
Titanium Dioxide	13463-67-7	0	- 0.15
Cured Resin	Mixture	20 - 45
Nylon Fiber	Mixture	5	- 20
Fiberglass Core	Mixture	0.5 -		5

*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret.

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2.Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3.Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products
Substance	Condition
Carbon monoxide	During Combustion
Carbon dioxide	During Combustion
5.3. Special protective actions for fire-fighters
No special protective actions for fire-fighters are anticipated.
SECTION 6: Accidental release measures

__________________________________________________________________________________________

Page 2 of 10

3M™ Scotch-Brite™ Products, Light Deburring Wheels, S FIN 05/19/15

6.1. Personal precautions, protective equipment and emergency procedures

For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Observe precautions from other sections.

6.2.Environmental precautions

Not applicable.

6.3.Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations. Combustible dust may form by action of this product on another material (substrate). Dust generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters

Occupational exposure limits

If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available for the component.

Ingredient	C.A.S. No.	Agency	Limit type	Additional Comments
Titanium Dioxide	13463-67-7	ACGIH	TWA:10 mg/m3	A4: Not class. as human
				carcin
Titanium Dioxide	13463-67-7	CMRG	TWA(as respirable dust):5
			mg/m3
Titanium Dioxide	13463-67-7	OSHA	TWA(as total dust):15 mg/m3
Talc	14807-96-6	ACGIH	TWA(respirable fraction):2	A4: Not class. as human
			mg/m3	carcin
Talc	14807-96-6	CMRG	TWA(as respirable dust):0.5
			mg/m3
Talc	14807-96-6	OSHA	TWA concentration(as total
			dust):0.3 mg/m3;TWA
			concentration(respirable):0.1
			mg/m3(2.4 millions of
			particles/cu. ft.);TWA:20
			millions of particles/cu. ft.
Quartz Silica	14808-60-7	ACGIH	TWA(respirable	A2: Suspected human
			fraction):0.025 mg/m3	carcin.
Quartz Silica	14808-60-7	OSHA	TWA concentration(as total
			dust):0.3 mg/m3;TWA
			concentration(respirable):0.1
			mg/m3(2.4 millions of
			particles/cu. ft.)

__________________________________________________________________________________________

Page 3 of 10