3M 60440205353, 60440205312, 60440205411, 60440205346, 60440205403 User Manual

3M™ Abrasive Products, 381C Fibre Discs, Grades 16-50, Roloc™ 02/17/14

Safety Data Sheet

Copyright,2014,3M Company.

All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon.

Document Group:	26-9643-3	Version Number:	1.04
Issue Date:	02/17/14	Supercedes Date:	03/22/13

SECTION 1: Identification

1.1. Product identifier

3M™ Abrasive Products, 381C Fibre Discs, Grades 16-50, Roloc™

1.2. Recommended use and restrictions on use

Recommended use

Abrasive Product

1.3. Supplier’s details	3M
MANUFACTURER:
DIVISION:	Abrasive Systems Division
ADDRESS:	3M Center, St. Paul, MN 55144-1000, USA
Telephone:	1-888-3M HELPS (1-888-364-3577)

1.4. Emergency telephone number

1-800-364-3577 or [phone] (24 hours)

SECTION 2: Hazard identification

2.1. Hazard classification

Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200.

2.2. Label elements Signal word

Not applicable.

Symbols

Not applicable.

Pictograms

Not applicable.

Notes to Physician:

Not applicable

2.3. Hazards not otherwise classified

None.

__________________________________________________________________________________________

Page 1 of 10

3M™ Abrasive Products, 381C Fibre Discs, Grades 16-50, Roloc™ 02/17/14

13% of the mixture consists of ingredients of unknown acute oral toxicity.

13% of the mixture consists of ingredients of unknown acute inhalation toxicity.

SECTION 3: Composition/information on ingredients

Ingredient	C.A.S. No.	% by Wt
Aluminum Oxide Mineral (non-fibrous)	1344-28-1	20	- 50
Inorganic Fluoride	15096-52-3	5 -	15 Trade Secret *
Filler	1317-65-3	2 -		10
Titanium Dioxide	13463-67-7	0.2	-	1.5 Trade Secret *
Quartz Silica	14808-60-7	0 -	0.15		Trade Secret *
Cured Resin	Mixture	5 - 15
Fibre Backing	Mixture	20	- 55
Attachment Button	Mixture	0 - 10

*The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret.

SECTION 4: First aid measures

4.1. Description of first aid measures

Inhalation:

Remove person to fresh air. If you feel unwell, get medical attention.

Skin Contact:

Wash with soap and water. If signs/symptoms develop, get medical attention.

Eye Contact:

Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention.

If Swallowed:

No need for first aid is anticipated.

4.2.Most important symptoms and effects, both acute and delayed

See Section 11.1. Information on toxicological effects.

4.3.Indication of any immediate medical attention and special treatment required

Not applicable

SECTION 5: Fire-fighting measures

5.1. Suitable extinguishing media

In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish.

5.2. Special hazards arising from the substance or mixture

None inherent in this product.

Hazardous Decomposition or By-Products
Substance	Condition
Carbon monoxide	During Combustion
Carbon dioxide	During Combustion

__________________________________________________________________________________________

Page 2 of 10

3M™ Abrasive Products, 381C Fibre Discs, Grades 16-50, Roloc™ 02/17/14

5.3. Special protective actions for fire-fighters

No unusual fire or explosion hazards are anticipated.

SECTION 6: Accidental release measures

6.1.Personal precautions, protective equipment and emergency procedures

Observe precautions from other sections.

6.2.Environmental precautions

Avoid release to the environment.

6.3. Methods and material for containment and cleaning up

Not applicable.

SECTION 7: Handling and storage

7.1. Precautions for safe handling

Avoid eye contact. For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations. Avoid release to the environment. Combustible dust may form by action of this product on another material (substrate). Dust generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions.

7.2. Conditions for safe storage including any incompatibilities

No special storage requirements.

SECTION 8: Exposure controls/personal protection

8.1. Control parameters Occupational exposure limits

Ingredient	C.A.S. No.	Agency	Limit type	Additional Comments
Filler	1317-65-3	US Dept of	TWA(as total dust):15
		Labor - OSHA	mg/m3;TWA(respirable
			fraction):5 mg/m3
Aluminum Oxide Mineral (non-	1344-28-1	Chemical	TWA:1 fiber/cc
fibrous)		Manufacturer
		Rec Guid
Aluminum Oxide Mineral (non-	1344-28-1	US Dept of	TWA(as total dust):15
fibrous)		Labor - OSHA	mg/m3;TWA(respirable
			fraction):5 mg/m3
Aluminum, insoluble compounds	1344-28-1	Amer Conf of	TWA(respirable fraction):1
		Gov. Indust.	mg/m3
		Hyg.
Titanium Dioxide	13463-67-7	Amer Conf of	TWA:10 mg/m3
		Gov. Indust.
		Hyg.
Titanium Dioxide	13463-67-7	Chemical	TWA(as respirable dust):5
		Manufacturer	mg/m3

__________________________________________________________________________________________

Page 3 of 10