Model : ZM-GWB2
VGA Water Block
Please visit our website and watch the ZM-GWB2 installation video for easy installation.
※ Please read this manual throughly before installation.
※ The specifications of this product and its components may change without prior notice to
improve performance.
http://www.zalman.co.kr http://www.zalmanusa.com
User
’’
s Manual
User
’’
s Manual
(English version)
※
The specifications of any product may change without prior notice to improve performance.
1
❶❷ ❸
❹❺❻❼ ❽❾ ❿
1) Pure aluminum base material is light-weight and ensures optimal heat dissipation.
2) Anodizing and surface coating prevents galvanic corrosion.
3) Included VGA RAM Heatsinks cool VGA RAM, complementing VGA chipset cooling.
1. Features
1) Weight : 60g (Water Block only)
2) Material : Pure Aluminum (Anodized)
3) Dimensions : 63(L) x 45(W) x 20(H)mm
4) Compatible Tubes (Outer x Inner) : 13 x 10 mm, 13 x 9 mm, 12 x 8 mm, 11 x 8 mm, 10 x 8 mm
2. Specifications
1) Water Block
2) Eight (8) RAM Heatsinks
3) One (1) Clip
4) Two (2) Tube Clamps
5) Two (2) Nipples
6) Two (2) Bolt A( 3 5mm)
7) Two (2) Bolt B( 2.3 6mm)
8) One (1) Thermal Grease
9) Four (4) Washers
10) User’s Manual(in English and Korea)
3. Components
1) Test the product for leakage before installation away from the system first.
After no leakage is confirmed, proceed with installation and use.
2) To prevent corrosion, only use coolant that has been approved for computer water-cooling.
3) Only use coolant tubes with compatible specifications.
4) The exposed core of a VGA chipset can be damaged due to improper installation.
Please read the “Installation Procedure” section thoroughly before installing.
5) If interference with components of the VGA card is encountered, do not install this product.
6) Keep this product and its associated system away from children.
Precautions
Zalman Tech Co., Ltd. is not responsible for any damages due to external causes, including
but not limited to, improper use, problems with electrical power, accident, neglect, alteration,
repair, improper installation, or improper testing.
Disclaimer
※
The specifications of any product may change without prior notice to improve performance.
2
Bolt A
Clip
VGA Water Block
Nipple
Washer
VGA RAM
RAM Heatsink
RAM Heatsink
Washer
Bolt B
4. Exploded View
※
The specifications of any product may change without prior notice to improve performance.
3
RAM Heatsink
VGA RAM
VGA Chipset
Thermal
Tape
Film
Nipple
Washer
Mounting
Hole
Washer
Bolt B
5. Components
1) Attaching the VGA RAM Heatsinks
Remove the film from the Thermal Tapes
on the bottom of the RAM Heatsinks and
attach the Heatsinks on the VGA RAM.
Note 1)
If thermal grease or other residue
remains on the RAM, the Thermal
Tapes will not stick.
Clean the surface of the RAM with
acetone or alcohol before
attaching.
Note 2)
The bonding strength of the Thermal
Tape reaches 90% after 24 hours
of curing.
Do not put excessive force on the
RAM Heatsinks during this period.
Note 3)
Thermal Tapes lose adhesiveness
after it has been used for attachment
once and cannot be reused.
Purchase Thermal Tapes separate
ly
for future reattachments.
2) Installing the Nipples
As shown in the diagram, install the Nipple
and Bolt B on the Mounting Hole with a
Washer in between on both sides of the
VGA card. Use only the supplied Washers.
Make sure to check the VGA card's correct
Nipple installation hole position to install
properly.
※
The specifications of any product may change without prior notice to improve performance.
4
Nipple Installation Holes for Various VGA Cards
NVIDIA Geforce4 Ti 4 Series
NVIDIA Geforce FX 5700(Ultra) Series
NVIDIA Geforce FX 5800 Series
NVIDIA Geforce FX 5900 Series
NVIDIA Geforce FX 5950 Series
NVIDIA Geforce 6600 Series (PCIe)
NVIDIA Geforce 6800 LE Series
NVIDIA Geforce 6800 Series
NVIDIA Geforce 6800 GT Series
NVIDIA Geforce 6800 Ultra Series
NVIDIA Geforce 6800 Ultra Extreme
***
ATI Radeon 9 Series
ATI Radeon X Series
NVIDIA Geforce4 MX Series
NVIDIA Geforce FX 5200
NVIDIA Geforce FX 5500
NVIDIA Geforce FX 5600(FX 5700)
VGA Chipset
Mounting Hole
Slot Connector
VGA Chipset
Mounting Hole
Slot Connector
VGA Chipset
Mounting Hole
Slot Connector
***
***
The Nipples must be installed through the mounting holes indicated with black holes
(●) as shown in the diagram.
3) Applying Thermal Grease
Clean the contact surface of the VGA chipset. Apply thermal grease on the VGA chipset (for
exposed core chipsets), only on the core that makes contact with the base of the VGA Water Block.
Thermal Grease
RAM Heatsink
Nipple
VGA Chipset
4) Installing the VGA Water Block
Place the VGA Water Block and the clip on
the center of the VGA chipset. Screw each
bolt B on each nipple slightly, and tighten
each bolt B a few turns at a time while
alternating between the two until the Clip
ends are completely pressed against the
Nipples.
Notes)
Make sure that the Water Block’s base
and the VGA Chipset are completely in
contact with each other.
5) Installing the VGA Card
Insert the assembled VGA card into the
motherboard’s AGP (or PCIe) slot. Use the
Fixing Bolt to fix the VGA card on to the
computer case. If the VGA card has an on-board
power connector, remember to plug in the
power cable.
6) Installing the Tubes and the Tube Clamps
Plug the tubes over the VGA Water Block’s
fittings and install the Tube Clamps.
Note 1)
Use a proper tool (e.g. cutting nipper)
when installing the Tube Clamps.
Note 2)
Hold the VGA Water Block with one hand
while installing the Tube Clamps so that
the Water Block does not move around.
※
The specifications of any product may change without prior notice to improve performance.
5
Bolt B
Clip
Nipple
VGA Chipset
Fixing Bolt
Tube
Tube Clamp
Northbridge Water Block
Noiseless Power SupplyCPU Water Block Heatpipe HDD Cooler
Noiseless Case Fan Fan Controller
※
The specifications of any product may change without prior notice to improve performance.
6
When building a noiseless computer, use Zalman’s CPU Water Block, Northbridge Water Block, Noiseless
Power Supply, Noiseless Case Fan, Heatpipe HDD Cooler, and Fan Controller for stable performance and
a noiseless Water-Cooled system.
6. Zalman Noise Prevention System
7. TNN (Totally No Noise) Computer Enclosure
The TNN 500AF is the world's first absolutely noiseless, anti-dust computer case for high-end systems that
has been developed with Heatpipe Technology, HSC (Heat Source Contact) Power Technology, High
Capacity Extrusion Technique, and FMS (Flexible Mounting Structure) Design Technology by ZALMAN
Tech Co., Ltd.
The TNN 500AF package includes a high performance aluminum computer case with an absolutely
noiseless cooling solution that does not require the use of a fan, making it ideal for:
1. Digital Audio Workstations (DAW) in broadcasting, recording, and postproduction studio control rooms.
2. Multi Media & Storage Servers for offices, educational facilities, and hotels.
3. Home Theater and Multi- Media Systems for living rooms.
4. High Performance Noiseless Workstations & Servers for SOHO (Small Office Home Office) systems.
For more information, please visit our website.
Loading...