ZALMAN VF700 User Manual

User
s Manual
User
s Manual
(English version)
Please visit our website and watch the VF700 installation video for easy installation.
Please read this manual thoroughly before installation. The specifications of this product and its components may change without prior notice to
http://www.zalman.co.kr http://www.zalmanusa.com
Model : VF700-Cu(AlCu)
Quiet VGA Cooler
* The specifications of any product may change without prior notice to improve performance.
1. Please read this manual thoroughly before installation.
2. After installing this product on a VGA(Video Graphics Array) card, a PCI slot adjacent to the AGP (or PCIe) slot will become unusable.
3. Should you install this product on a newly released VGA card, please check for compatibility at Zalman’s website first.
4. This product is not compatible with Matrox VGA cards and NVIDIA PCX 5 VGA cards.
5. If the VGA card and its components interfere with the installation of this product, stop the installation, refer to the list of compatible VGA cards at Zalman's website and install this product with one of the compatible VGA cards.
6. To enhance the performance of this product, using a rear case fan is recommended.
7. Zalman is not responsible for any problems arising from incorrect installation.
8. Zalman Tech Co., Ltd. is not responsible for any damages due to external causes, including but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation, or improper testing.
1
Cautions on Use and Installation
1. Pure copper and/or aluminum ensures excellent heat dissipation.
2. Fan installed in the heatsink (FHS) cools not only the VGA chipset and VGA RAM, but all other VGA components as well.
3. Does not generate noise or vibration in Silent Mode.
4. Silent Mode and Normal Mode selection provided to accommodate the user's environment and preference.
Product Features
1. FHS Assembly
2. Eight (8) RAM Heatsinks
3. One (1) Brace Plate
4. Two (2) Nipple ‘A’
5. Two (2) Nipple ‘B’
6. Four (4) Bolt 'A' (
Ø
3 x 5mm)
7. Four (4) Bolt 'B' (
Ø
4 x 4mm)
8. Six (6) Rubber Rings
9. Thermal Grease
10. One (1) Multi-Connector
11. User’s Manual
Components
󱆌
1. Specifications
Specifications
VF700-AlCu
180
Pure Aluminum+Pure Copper
91(L) x 126.4(W) x 30(H)
Weight (g)
Cooling Material
Dimensions (mm)
VF700-Cu
270
Pure Copper
2. Fan
- Size : 80(L) x 80(W) x 15(H)mm
- Bearing Type : 2-Ball
- Speed : 1,350rpm ± 10%(Silent Mode), 2,650rpm ± 10%(Normal Mode)
- Noise Level : 18.5dB ± 10%(Silent Mode), 28.5dB ± 10%(Normal Mode)
❹❺❻❼❽❾
* * *
* The specifications of any product may change without prior notice to improve performance.
Exploded View
2
Bolt A
FHS Assembly
RAM Heatsink
Nipple A
Rubber Ring
Rubber Ring
VGA Chipset
Nipple B
RAM Heatsink
Brace Plate
Bolt B
VGA RAM
* The specifications of any product may change without prior notice to improve performance.
3
Installation Procedure
Nipple Installation Holes for Various VGA Cards
NVIDIA Geforce4 Ti 4 Series NVIDIA Geforce FX 5700(Ultra) Series NVIDIA Geforce FX 5800 Series NVIDIA Geforce FX 5900 Series NVIDIA Geforce FX 5950 Series NVIDIA Geforce 6600 Series
NVIDIA Geforce 6800 LE Series NVIDIA Geforce 6800 Series NVIDIA Geforce 6800 GT Series NVIDIA Geforce 6800 Ultra Series NVIDIA Geforce 6800 Ultra Extreme
VGA Chipset
Mounting Hole
Slot Connector
VGA Chipset
Mounting Hole
Slot Connector
***
ATI Radeon 9 Series ATI Radeon X Series NVIDIA Geforce4 MX Series NVIDIA Geforce FX 5200 NVIDIA Geforce FX 5500 NVIDIA Geforce FX 5600(FX 5700)
VGA Chipset
Mounting Hole
Slot Connector
*** ***
The Nipples must be installed through the mounting holes indicated with black holes(●) as shown in the diagram.
2. Install the Brace Plate
Use each Bolt B to attach the brace plate to
each Nipple B as shown in the diagram.
1. Install the Nipples ‘A’ and ‘B’
Check VGA card for compatible installation hole positions. Install nipple ‘A’ and nipple ‘B’ on the heatsink
Mounting Holes as shown in the diagram. Remember to use rubber rings in between.
Nipple A
Rubber Ring
Mounting Hole
Nipple B
Nipple A Nipple B
Rubber Ring
Screwdriver Bolt B
Nipple B
Brace Plate
The following installation sequence MUST be followed.
(Nipple A and B →Brace Plate →VGA RAM Heatsinks →Thermal Grease Application →VGA Cooler
VGA Card →Supply Power)
Notes) The Nipples MUST be tightened by hand. Using tools to tighten
the nipples may break the tip of the nipples.
* The specifications of any product may change without prior notice to improve performance.
4
4. Apply Thermal Grease
Clean the contact surface of the VGA Chipset
completely. Apply thermal grease on the VGA
Chipset that makes contact with the
base of the FHS assembly.
5. Install the FHS Assembly
Align the FHS assembly’s base on the center of the VGA Chipset. Screw each Bolt A on each Nipple A slightly, and tighten each Bolt A a few turns at a time, alternating between each bolt, until the clip is completely attached to each Nipple A.
Notes) Make sure that the heatsink's base
and the VGA Chipset are completely in contact with each other.
RAM Heatsink
Nipple A
VGA Chipset
Thermal Grease
Bolt A
FHS Assembly
Clip
Nipple A
VGA Chipset
3. Attach the VGA RAM Heatsinks
Remove the film from the thermal tapes on the bottom of the RAM Heatsinks and attach the heatsinks on the VGA RAM.
Note 1) If thermal grease or other residue remains
on the RAM, the thermal tapes will not stick. Clean the surface of the RAM with acetone or alcohol before attaching.
Note 2) The bonding strength of the thermal tapes
reaches 90% after 24 hours of curing. Do not put excessive force on the RAM heatsinks during this period.
Note 3)
Thermal tapes lose adhesiveness after it has been used for attachment once and cannot be reused. Purchase thermal tapes separately should you try again.
RAM Heatsink
VGA RAM
Thermal Tape
Film
Nipple A
VGA Chipset
* The specifications of any product may change without prior notice to improve performance.
5
6. Install the VGA Card
Insert the assembled VGA card into the motherboard’s AGP (or PCIe) slot.
Use the Fixing Bolt to fix the VGA card on to the computer case. If the VGA card has a power connector on it, remember to plug in the power cable.
7. Supply Power to the Fan
Connect the Multi-Connector to the power supply’s 4-pin connector as shown in the diagram.
AGP Slot
Fixing Bolt
Speed
Noise
Silent Mode (5V)
1,350rpm
±
10%
18.5dB
±
10%
Normal Mode (12V)
2,650rpm
±
10%
28.5dB
±
10%
VF700 Fan Connector
5V
Multi Connector 3-Pin
Multi Connector 4-Pin
Power Supply 4-Pin Connector
12V
* The specifications of any product may change without prior notice to improve performance.
6
When building a noiseless computer, use Zalman’s Noiseless CPU Cooler, Noiseless Power Supply, Noiseless Case Fan, Noiseless Northbridge Cooler, and Heatpipe HDD Cooler for stable performance and a noiseless environment.
Zalman Noise Prevention Systems
Noiseless Power Supply
Fanless Northbridge Cooler
Heatpipe HDD Cooler
Quiet CPU Cooler
Noiseless Case Fan
The TNN 500AF is the world's first absolutely noiseless, anti-dust computer case for high-end systems that has been developed with Heatpipe Technology, HSC (Heat Source Contact) Power Technology, High Capacity Extrusion Technique, and FMS (Flexible Mounting Structure) Design Technology by ZALMAN Tech Co., Ltd.
The TNN 500AF package includes a high performance aluminum computer case with an absolutely noiseless cooling solution that does not require the use of a fan, making it ideal for:
1. Digital Audio Workstations (DAW) in broadcasting, recording, and postproduction studio control rooms.
2. Multi Media & Storage Servers for offices, educational facilities, and hotels.
3. Home Theater and Multi- Media Systems for living rooms.
4. High Performance Noiseless Workstations & Servers for SOHO (Small Office Home Office) systems.
For more information, please visit our website.
TNN (Totally No Noise) Computer Case
Loading...