ZALMAN Z11 Plus, Z11 User Manual

English

Z11

Cautionary Note

1

1) Please read this manual thoroughly prior to installation.

2) Before installing, check the components and condition of the product,
and if any problem is found, contact the retailer.

3) Avoid inserting objects or hands into the system while it is in operation
to prevent product damage and injuries.

4) Check the manual when connecting cables. Incorrect connections

may cause short circuits leading to re hazards.

5) Do not block the front intake vent or the rear exhaust vent.

6) Keep this unit away from heat sources, direct sunlight, water, oil, and

humid environments, and place the unit on a at, stable, vibration-free,
and well-ventilated area.

7) Do not clean the product surface with chemicals or wet cloth.

(chemicals: industrial brightener, wax, benzene, alcohol, paint thinner,

mosquito repellent, aromatics, lubricant, detergent etc.)

8) Please wear gloves while handling this product to prevent injuries.

9) Product design and specications may be revised to improve quality

and performance.

ENG

Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages

due to external causes, including but not limited to, improper
use, problems with electrical power, accident, neglect,
alteration, repair, improper installation, or improper testing.

1

Z11

2

Product Details

(1) Speci󰘰cations

Models

Type ATX Mid Tower

Dimensions (W×H×D) 207 × 464 × 504㎜ (8.1 × 18.2 × 19.8”)

Weight

Materials Plastic, Steel

Motherboard Compatibility Standard ATX / m-ATX

Power Supply Compatibility Standard ATX / ATX12V

PCI/AGP Compatibility Full Size 290㎜ (11.4")

Drive Bays

Expasion Card Solts 7 Slots

Cooling

Components

Z11 Plus 7.4kg (16.3 lb)

Z11 7.3kg (16.1 lb)

Color Black

5.25” External Bay x 4

3.5“ External Bay x 1, Internal Bay x 5

5.25"/3.5"/2.5”

Hot-swap

Front

Z11 Plus

Top

Z11 120mm/140mm Fan Vent x 2 (Fans optional)

Rear 120mm Fan Vent x 1 (1 Fan included)

120mm/140mm Fan Vent x 1 (1 Fan included)

Z11 Plus / Z11

1 (3in-1)

-

120mm/140mm Fan Vent x 2

(1 Fan included, 1 optional)

Side 80mm Fan Vent x 2 (2 Fan included)

Bottom

Z11 Plus Headphones x 1, Mic x 1, USB 2.0 x 2, USB3.0 x 2

Front Panel I/O Port

Z11 Headphones x 1, Mic x 1, USB 2.0 x 4

120mm/140mm Fan Vent x 1 (Fan optional)

2

(2)Parts

Z11

ENG

User manual

Stand-Off × 5Main Unit

Bolt A(#6-32*6mm) × 11

[PSU, PCI]

Bolt D(#6-32*4mm) × 20

[3.5” Bay HDD]

PCI Slot × 2

Bolt B(M3*5mm) × 17

[M/B, FDD, SSD]

Bolt E(#6-32*6mm) × 5

[3.5” HDD]

Bolt C(M3*6mm) × 12

[5.25”Bay ODD]

HDD Anti-vibration

rubber × 20

[3.5” Bay HDD]

Cable Tie × 5CPU 12V Extension Cable × 1

3

Z11

Installation

3

(1) Side Panel Removal

②

①

(2) Motherboard Installation

There are 4 Stand Offs preinstalled. Please refer to the diagrams below for
additional Stand Off positions (based on motherboard type).

ATX Board

m-ATX Board

or

Stand-Off

B Bolt

4

(3) 5.25” and 3.5” Drive Installation

1) Front Cover Removal

2) ODD Installation

Z11

ENG

PULL

Bolt C

3) 2.5” / 3.5” Tray Installation

Tray removal

①

Bolt C

5

Z11

Attach Drive to Tray

②

A. 3.5” FDD Installation

3.5” FDD

B. 3.5” HDD Installation

3.5” HDD

Bolt B

C. 2.5” SSD Installation

SSD

Bolt B

(4) Front Cover Installation

When removing the front cover, the power switch and extension
cable are separated to prevent disconnection. Be sure to connect
them before installing the front cover.

Bolt A

6

(5) 3.5” HDD Installation

Z11

HDD

When transporting an assembled
system, please secure the HDD with
Bolt E as shown above.

Bolt E

(6) Cable Connection

Power Button

Bolt D

HDD Anti-

vibration rubber

ENG

When removing HDD, pull the fastening
lever outwards and then remove it.

Fan Connection

or

Power LED Power

Mother Board

PSU Power Fan Fan

7

Z11

Front Panel I/O Port

Audio

Reset

HD Audio

Power and I / O ports to connect please refer to your motherboard. manual.

※

USB 2.0 X 2 USB 3.0 X 2

AC ’97

MotherBoard

HDD LED

(7) 2.5” HDD / SSD Optional

2.5" HDD and SSDs can be installed on the right side of case as shown in the
diagram below.

Bolt B

(8) Optional Fan Installation and Replacement

Top Panel Fan (120/140 mm) Installation

When installing fan, press the Top Panel’s eight Hook’s towards each other
to remove and install as shown in diagram below. The Z11 comes with one

120mm Fan pre-installed.

8

#1007 daeryung Techno Town III, 448 Gasan-dong, Gumchun-gu, Seoul, 153-803,Korea

Tel: [phone] / Fax: [phone] / www.zalman.com / e-mail: [e-mail]

Zalman Tech Co., Ltd.

Tel: [phone] / Fax: [phone] / www.zalman.com / e-mail: [e-mail]

10531 Garden Glove Blvd., Garden Grove, CA 92843, U.S.A

Zalman USA, Inc.