Yamaha PSR-S550, PSR-S550B User Manual

SERVICE MANUAL
PSR-S550 PSR-S550B

CONTENTS(目次)

SPECIFICATIONS..................................................................... 3
PA NEL LAYOUT ........................................................................ 4
CIRCUIT BOARD LAYOUT & WIRING
EXTENSION CABLE FOR SERVICE USE
(サービス用延長ケーブル).............................................. 7
BLOCK DIAGRAM(ブロックダイアグラム)........................... 8
DISASSEMBLY PROCEDURE(分解手順).............................. 9
LSI PIN DESCRIPTION(LSI端子機能表)............................. 16
IC BLOCK DIAGRAM (ICブロック図)................................. 20
CIRCUIT BOARDS(シート基板図)...................................... 21
TEST PROGRAM ................................................................... 33
INITIALIZATION ...................................................................... 37
DATA BACKUP ........................................................................ 38
SYSTEM BOOTING FLOW CHART ....................................... 43
MIDI IMPLEMENTATION CHART
(MIDIインプリメンテーションチャート)..................... 44
MIDI DATA FORMAT ............................................................... 45
PA RTS LIST
OVERALL CIRCUIT DIAGRAM(総回路図)
PK 001810
HAMAMATSU, JAPAN
Copyright (c) Yamaha Corporation. All rights reserved. ’08.08
PSR-S550/PSR-S550B
p
p
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
WARNING:
IMPORTANT:
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division.
WARNING:
IMPORTANT:
WARNING: This product contains chemicals known to the State of California to cause cancer, or birth defects or other
reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER!
IMPORTANT NOTICE
Failure to follow appropriate service and safety procedures when servicing this product may result in per­sonal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative.
This presentation or sale of this manual to any individual or firm does not constitute authorization certifi­cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.
Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.)
Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/ flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.
WARNING
Components having special characteristics are marked and must be replaced with parts having specification equal to those originally installed.
SAVING DATA
Saving and backing up your data
The panel settings and some other types of data are not retained in memory when you turn off the power to the instrument. Save data you want to keep to the Registration Memory. Saved data may be lost due to malfunction or incorrect operation.
Be sure to
erform it
Backing up the USB storage device/external media
Be sure to
erform it
Save important data to a USB storage device/or other external device such as a computer.
To protect against data loss through media damage, we recommend that you save your important data onto two USB storage devices/external media.
2

SPECIFICATIONS

Keyboards
• 61 Standerd-size keys (C1–C6), with Touch Response.
Display
• 320 x 240 dots LCD display (backlit)
Setup
• STANDBY/ON
•MASTER VOLUME: MIN–MAX
• LCD CONTRAST
Panel Controls
• DEMO, SONG MODE
•SONG-PRESET, SONG-USER, SONG-SCORE, SONG-LYRICS, SONG-REC
• STYLE CATEGORY, VOICE CATEGORY
• TRANSPOSE [-] [+], METRONOME, TAP TEMPO, TEMPO [-] [+]
•OTS LINK, AUTO FILL IN, ACMP, INTRO [1]–[3], MAIN VARI­ATION [A]–[D], ENDING/rit. [1]–[3] (REW) (FF), SYNC STOP (A-B REPEAT), SYNC START (PAUSE), START/STOP
• REGIST/PART [MIXER], MEMORY, REGIST BANK [-] [+], REGISTRATION MEMORY [1]–[8], STYLE [1]-[8], SONG [1/9]-[8/16], EXIT, CATEGORY [ ] [ ], Dial, [+/YES] [-/NO]
• EXECUTE, MDB, FILE MENU, FUNCTION, ONE TOUTCH SETTING [1]–[4], LEFT, DUAL, HARMONY, TOUCH, SUSTAIN, DSP, UPPER OCTAVE [-] [+]
Realtime Control
•Pitch Bend Wheel
Voice
• 294 Voices + 12 Drum Kits + 10 SFX Kits + 480 XG Voices (Included 11 Regional Voices and 8 Regional Drum/Percussion Kits)
• Polyphony: 64
• LEFT
• DUAL
Style
• 176
• Style Control: ACMP ON/OFF, SYNC STOP, SYNC START,
START/STOP, INTRO [1]–[3], MAIN VARIA­TION [A]–[D], ENDING/rit. [1]–[3], AUTO FILL IN
•Fingering: Multi Finger, Full Keyboard
• Style Volume
Music Database
• 600
Registration Memory
•8 banks x 8 memories
• Regist Clear
Effects
• Harmony: 26 types
• Reverb: 35 types
• Chorus: 44 types
• DSP: 237 types
Song
•5 Preset Songs + User Songs + USB Memory
• Song Clear, Track Clear
• Song Volume
• Song Control: A-B REPEAT, PAUSE, REW, FF, START/STOP
Recording
• Song User Song: 5 Songs Recording Tracks: 1
-
16, STYLE
MIDI
• Local On/Off
• Initial Setup
• External Clock
• Keyboard Out
• Style Out
• Song Out
Auxiliary jacks
• PHONES/OUTPUT, DC IN 16V, USB TO HOST,
USB TO DEVICE, SUSTAIN
Amplifier
• 12W x 2
Speakers
• (12cm + 3cm) x 2
Power Consumption
• 25W
Power Supply
• Adaptor: Yamaha PA-301 or PA-300 AC power adaptor
Dimensions (W x D x H)
• 946 x 402 x 130 mm (37-1/4" x 15-7/8" x 5-1/8")
Weight
• 7.5kg (16 lbs., 9 oz.)
Supplied Accessories
•Music Rest
• Accessory CD-ROM
• Keyboard Stand: L6
• Foot Switch: FC4/FC5
• Owner’s Manual
• AC Power adaptor (May not be included depending on your par-
ticular area.)
Optional Accessories
• Headphones: HPE-150
• Style Creator
Function
•VOLUME: Style Volume, Song Volume
•OVERALL: Tuning, Pitch Bend Range, Split Point, Touch Sensitivity, Chord Fingering
•MAIN VOICE: Volume, Octave, Pan, Reverb Level, Chorus Level, DSP Level, Dry Level
• DUAL VOICE: Volume, Octave, Pan, Reverb Level, Chorus Level, DSP Level, Dry Level
• LEFT VOICE: Volume, Octave, Pan, Reverb Level, Chorus Level, DSP Level, Dry Level
• EFFECT: Reverb Type, Chorus Type, DSP Type, Master EQ Type
• HARMONY: Harmony Type, Harmony Volume
• PC: PC Mode
•MIDI: Local On/Off, External Clock, Keyboard Out, Style Out, Song Out, Initial Setup
•METRONOME: Time Signature Numerator, Time Signature Denominator, Bell On/Off, Metronome Volume
• SCORE: Quantize, Right-Part, Left-Part
• UTILITY:
• LANGUAGE: Language
Demo Cancel, TG Mode
Mixer
• Volume, Pan, Reverb, Chorus
• Style Creator
• USB
PSR-S550/PSR-S550B
3
PSR-S550/PSR-S550B

PANEL LAYOUT

r
e
q
y u
w
#3
#2
• Front Panel
[STANDBY/ON] switch
q w [MASTER VOLUME] control e [DEMO] button r [SONG MODE] button t SONG
[PRESET], [USER], [SCOPE] [LYRICS] buttons
y [USB] button u [REC] button i STYLE o STYLE CONTROL
[OTS LINK], [AUTO FILL IN], [ACMP] INTRO[I]-[III], MAIN VARIATION [A]-[D] ENDING/rit. [I]-[III], [SYNC STOP] [SYNC START], [START/STOP] buttons
!0 SONG CONTROL
[ ], [ ], [A B], [ ], [ / ] buttons
t i
!1 TRANSPOSE [+] and [
!2 [METRONOME] button
!3 [TAP TEMPO] button !4 TEMPO [+] and [ !5 [REGIST/PART[MIXER]] button !6 [MEMORY] button !7 REGIST BANK [+] and [ !8 Style Part/Song Part [1/9]-[8/16]/
REGISTRATION MEMORY [1] - [8] buttons
!9 DISPLAY @0 [EXIT] button
-
] buttons
-
] buttons
-
] buttons
o
!1
!2 !3 !4
!0
!5
!6
!7
4
!9
PSR-S550/PSR-S550B
@0
@1
!8
@3
Rear Panel
@1
Dial
@2
[+/YES] and [-/NO] buttons
@3
CATEGORY [ ] and [ ] buttons
@4
[EXECUTE] button
@5
[MDB] button
@6
[FILE MENU] button
@7
[FUNCTION] button
@8
ONE TOUCH SETTING [1] - [4] buttons
@9
VOICE
#0
VOICE CONTROL [LEFT], [DUAL], [HARMONY], [TOUCH] [SUSTAIN], [DSP] buttons
#1
UPPER OCTAVE [+] and [-] buttons
#2
[PITCH BEND] wheel
#3
Drum Kit
 
@4 @5
@9
@2
@6 @7
@8
#0
#4 #5 #6 #7 #8
#1
• Rear Panel
#4
SUSTAIN jack
#5
USB TO HOST and TO DEVICE terminals
#6
CONTRAST knob
#7
PHONES/OUTPUT jack
#8
DC IN 16V jack
5
PSR-S550/PSR-S550B

CIRCUIT BOARD LAYOUT & WIRING(ユニットレイアウト及び結線図)

• Upper Case Assembly
Ass’y
W401
550
JACK
AM
540
520560
TWTW
PNR
ENC PNCDM
30
PNL
500510530
PSW
MVR
PB
• Lower Key Bed Assembly
6
61L 61H
Ass’y
L30 L40L50
No. Ref. Part No. Assembly Destination Remarks
JK-AM e
xtension cab
AM-DM e
xtension cab
No.
130 (WH33630) 2 500 WJ465900 FFC4 PNL-CN102 3 510 WJ466000 FFC5 PNC-CN202 4 520 WQ075900 FFC2 DM-CN701 5 530 WJ465800 FFC3 DM-CN901 6 540 (WJ46010) 7 550 WJ465600 FFC1 DM-CN501 8 560 WH336400 LCD AM-CN102 LCD 2P
9 L30 WE13850R MK1 DM-CN801 61H-CN1 12P L=220 10 L40 WE13870R MK2 DM-CN803 61H-CN2 5P L=250 11 L50 WE13880R MK3 DM-CN802 61L-CN5 7P L=190
12 W401 (WJ45910)
*1: The parts with "( )" in "Part No." are not available as service parts.
*1:上記束線のうち、部品No.に"()"がついている部品は、サービス部品として準備されていません。
*2: Edge mark is adjusted to pin 1 mark( mark).
*2:エッジマークを1ピン側(マーク)に合わせます。
(パーツNo.) (束線) (行き先) (備考)
*1
*1
*1
SP JACK-CN453 SP(WF) 4P
*2
PNR-CN301
*2
*2
*2
PNL-CN101 PNL-CN103 AM-CN104
*2
*2
*2
*2
14P 21P 7P 27P
JKAM AM-CN101 JACK-CN451 10P
*2
JACK-CN403
*2
14P
GND JACK(Soldered) FG L=70
PSR-S550/PSR-S550B

EXTENSION CABLE FOR SERVICE USE(サービス用延長ケーブル)

Check the AM circuit board and the DM circuit board by using the following extension cables.
(AMシートやDMシートは、下記の延長ケーブルを使うとチェックが容易になります。)
1.JK-AMextensioncable(JK-AMシート間の延長ケーブル)
V8973600 JUMPER WIRE FVP=2.0C26SB10-400(ジャンパーワイヤーFVP=2.0C26SB10-400)
2. AM-DM extension cable(AM-DMシート間の延長ケーブル) WG123900 FFC CABLE P-70 (FFCケーブルP-70)
DM
JK-AM e
xtension cab
leJK-AM extension cable
AM-DM e
xtension cab
leAM-DM extension cable
7
8
28CA1-2001035400
PNC
ENC
PSW
PNL
PNR
DM
61L
JACK 2/2
CN403-14P
CN501-14P
SUSTAIN
TO DEVICE TO HOST
CONTRAST
JK401 CN401 CN402
VR401
USB
LCD
BACKLIGHT
LCD
UNIT
SW & LED
Matrix
LED
DRIVER
TR101-115
CPU
IC101(64P)
SW & LED
Matrix
SW & LED
Matrix
ROTARY
ENCODER
PA- 301
AC ADAPTER
AC IN
TW-L
3cm
TW-R
3cm
WF-R
12cm
8
WF-L 12cm
8
EC301
JK451
+16V
+5V
Regulator
+5A
6
14
11,13
1
1
2
1
3
8,9
+5D_2
+5LD
+5D
+5D
VR320
+5LD
+5A
+5A
RD/WRN,/WE0,/WE1/RASL, /CASL,CKIO,CKE
PNL_IC
D[0-15]
AD[0-25]
PITCH_BEND
/ENC-A,ENC-B
/DAC-IC
SYSCLK(LCDC)
+ 3.3D
+1.2V
+3.3V
Regulator
+1.2V
Regulator
IC14-16P
DAC 24bit
ROM
256Mbit(*1)
Wave
IC13-14P
Level
Converter
IC17-44P
Key Scan CPU
MKS
CPU
SWX2
DC/DC
Converter
IC4-64P
LCDC
ROM
128MBit(*1)
Program
FLASH ROM
16MBit(*2)
Data
SDRAM
128MBit(*3)
IC13,IC24-14P
Level
Converter
IC7-316P
IC1-3P
IC6-3P
IC19-8P
IC9-56P IC10-48P IC8-54P
Keyboard 61Key 16N
with touch response
BUS Clk 67.7376MHz Int. Clk 135.4752MHz
Ext. Clk 33.8688MHz
5MHz
Ceramic
IC5-5P
Reset
IC18-5P
USB
Bus Power
Controller
48MHz
Crystal OSC
16.9344MHz Crystal OSC
IC16-8P
LPF
+3.3D
+3.3D
+3.3D
PNL_IC
+29V
VBUS
FUNCTION D+,D-
FUNC_DP,DM
HOST_DP,DM
OVER_CUR_N
POWER_ENB
PK2
PD6 SDO0 WCLK BCLK
SYSCLK
PK0,PK1
*B *C
AN3
PD7
6
5
*A39
RxD0
PD3
PEDAL
VEE1
/LCD_OFF
/LCD_IC
/CS4
/WE0,/RD
D[0-7]
A[0-15]
/CS0
/CS5
/CS3
D[0-15]
D[0-15]
A[1-20]
A[1-14]
/DTA-WP
/WE1,/RD
/H-RES
/PRG-WP
D[0-15]
A[1-23]
/WE1,/RD
/H-RES
SYSCLK
+3.3D
43
14
+3.3D
37
+3.3D
+5D
1,3,9,14 27,43,49
FPFRAME
FPLINE
FPSHIFT
MOD
FPDAT[0-3]
VBUS
VBUS
to Device D+, D-
to Host D+, D-
/WAIT
B[7-11]
B[1-7]
N[11-16]
N[21-26]
RD2
CS4N
CS0N
CS5N
CS3N
A[0-25]
D[0-15]
PG2
PG7
RDN
WE1N
WE0N
PK7
TxD0
RESN
XTAL
EXTAL
VBUS
VEE2
+5V,500mA
+20 - 26V
HOST D+,D-
IC11-56P
+1.2D
/H-RES
/H-RES
UCLK
X1
/SCK0
TIO
/RESET
X2
MKS_TX
MKS_SCLK
MKS_REQ
/MKS_IC
/MRD
RxD1
SCK1
TxD1
EICN
/MWR
/MCS0
MA[1-25]
MD[0-15]
+5A
+5D
IC101-5P
IC201-14P
IC102-3P
A Curve
5k
+5V DC/DC
Converter
Power AMP
12W x 2 LA4625
STANDBY/ON
LCD DISPLAY
320 X 240
STN
CN601-14P
CN701-7P
CN702-3P
CN330-4P
CN452-4P
JK452
CN301-3P
CN103-7P
CN101-21P
CN202-21P
CN104-27P
CN901-27P
CN455-2P
CN453-4P
CN454-2P
CN102-14P
CN301-14P
CN102-2P
CN204-5P
CN310-5P
CN103-3P
CN320-3P
CN451-10P
CN101-10P
7
+5LD
8MHz
+5LD
PHONES/
OUTPUT
DCIN 16V
MASTER VOLUME
PITCH BEND
+-
JACK
AM
PB
MVR
1/2
CN802-7P
CN801-12P
CN803-5P
CN5-7P
CN4-12P
CN3-12P
61H
CN1-12P
CN2-5P
+5D
14
14
8
+3.3D
43
+5D
17,38
+5D
4
+5D_2
*A: 7,12,22,25
32,40,48,55
*B: A20,B19,B20,C18,D8,D10
D17,D18,E8,E10,E11,E13 H5,H16,H19,H20,N5,N16 T8,T10,T11,T13,U4,U17 V3,V18,W2,W19Y1,Y20
*C: E5,E6,E15
E16,F5,F16 K5,K16,L5 L16,R5,R16 T5,T6,T15,16
PSR-S550/PSR-S550B

BLOCK DIAGRAM(ブロックダイアグラム)

DISASSEMBLY PROCEDURE(分解手順)

Front Side (Printed Side)
(表面(印刷面))
Back Side
(裏面)
CAUTION:
•Be sure to attach the removed filament tape just as it was before
removal.
• Contacts are visible from the back. Pay attention not to insert and
install the cable to the connector inversely. (Fig.1)
(注意):
一度剥がしたフィラメントテープは、取り外す前と同じよう に、取り付けてください。
フラットケーブルの接点が裏側から透けて見えます。コネクタ にケーブルの表、裏を逆に差し込まないように注意して取り付 けてください。(図1)
PSR-S550/PSR-S550B
Fig.1(図1)
1. Lower Case Assembly (Time required: About 2 minutes)
1-1 Remove the six (6) screws marked [80A] , the two (2)
screws marked [100A] and the two (2) screws marked
[90]. The lower case assembly can then be removed.
(Fig.2)
[80B]
[90]
[80A]

Lower Case Assembly

(下ケースAss'y)
1. 下ケースAss'y (所要時間:約2分)
1-1 [80A]のネジ6本、[100A]のネジ2本、[90]のネジ2本を外し、
下ケースAss'yを外します。(図2)
[100A]
[90]
[80A]
[80B]
Push Knob
(プッシュツマミ)
[80]: BindHeadTappingScrew-B3.0X12MFZN2W3(WE98740R)Bタイト+BIND [90]: BindHeadTappingScrew-B3.0X20MFZN2W3(WF48930R)Bタイト+BIND [100A]: BindHeadTappingScrew-B3.0X30MFZN2W3(WF49100R)Bタイト+BIND
Keyboard Assembly
(16N-C61鍵盤Ass'y)
Upper Case Assembly
(上ケースAss'y)
Fig.2(図2)
9
PSR-S550/PSR-S550B

2. AM Circuit Board (Time required: About 3 minutes)

2-1 Remove the lower case assembly. (See procedure 1.)
2-2 Remove the five (5) screws marked [380B]. The AM
circuit board can then be removed. (Fig.3)

3. JACK Circuit Board (Time required: About 3 minutes)

3-1 Remove the lower case assembly. (See procedure 1.)
3-2 Remove the AM circuit board. (See procedure 2.)
3-3 Remove the screw marked [380E] at the location of “A”.
(Fig.4)
*As for the screw marked [380E] at the location of “A”, it
is tightened together with a GND terminal. (Fig.4)
3-4 Remove the five (5) screws marked [380A] and the two
(2) screws marked [385]. The JACK circuit board can
then be removed. (Fig.3)
(Lower Key Bed Assembly)
(下ケース鍵盤Ass'y)
2. AMシート (所要時間:約3分)
2-1 下ケースAss'yを外します。(1項参照) 2-2 [380B]のネジ5本を外し、AMシートを外し ま す。(図3)
3. JACKシート (所要時間:約3分)
3-1 下ケースAss'yを外します。(1項参照) 3-2 AMシートを外し ま す。(2項参照) 3-3 Aの位置の[380E]のネジ1本を外します。(図4) *Aの位置の[380E]のネジはGND端子と共締めされてい
ます。(図4)
3-4 [380A]のネジ5本と[385]のネジ2本を外し、JACKシートを外
します。(図3)
[380B]
[100B]
(Upper Case Assembly)
(上ケースAss'y)
[380C]
PSW
(L)
TW
Tw eeter (L)
(ツィーター(左))
[380D]
(Woofer (L))
(ウーファー(左))
[40]: BindHeadTappingScrew-B4.0X12MFZN2W3(WE98120R)Bタイト+BIND [100B]: BindHeadTappingScrew-B3.0X30MFZN2W3(WF49100R)Bタイト+BIND [380]: BindHeadTappingScrew-B3.0X8MFZN2W3(WE774301)Bタイト+BIND [385]: BindHeadTappingScrew-B3.0X12MFZN2W3(WE98740R)Bタイト+BIND
AM
[40] [40] (Woofer (R))
[385] [380A]
JACK
(Lower Case Assembly)
(下ケースAss'y)
(ウーファー(右))
(R)
TW
Tw eeter (R)
(ツィーター(右))
[380D]
10
Fig.3(図3)
PSR-S550/PSR-S550B

4. DM Circuit Board (Time required: About 4 minutes)

4-1 Remove the lower case assembly. (See procedure 1.)
4-2 Remove the AM circuit board. (See procedure 2.)
4-3 Remove the four (4) screws marked [380E]. The DM
circuit board can then be removed. (Fig.4)
*As for the screw marked [380E] at the location of “A”, it
is tightened together with a GND terminal. (Fig.4)
PNL PNR
[380I]
[380G]
PNC
PB
MVR
[380H]
[380]:BindHeadTappingScrew-B3.0X8MFZN2W3(WE774301)Bタイト+BIND
Fig.4(図4)
5. LCD Unit (Time required: About 5 minutes)
5-1 Remove the lower case assembly. (See procedure 1.)
5-2 Remove the AM circuit board. (See procedure 2.)
5-3 Remove the DM circuit board. (See procedure 4.)
5-4 Remove the four (4) screws marked [380L]. The LCD
unit can then be removed. (Fig. 5)
4. DMシート (所要時間:約4分)
4-1 下ケースAss'yを外します。(1項参照) 4-2 AMシートを外し ま す。(2項参照) 4-3 [380E]のネジ4本を外し、DMシートを外し ま す。(図4) *Aの位置の[380E]のネジ1本はGND端子と共締めされ
ていま す。(図4)
ENC
[380J]
[380F]
[380K]
DM
[380E]
A
5. 液晶ユニット
(所要時間:約5分)
5-1 下ケースAss'yを外します。(1項参照) 5-2 AMシートを外し ま す。(2項参照) 5-3 DMシートを外し ま す。(4項参照) 5-4 [380L]のネジ4本を外し、液晶ユニットを外 し ま す。(図5)

6. ENC Circuit Board (Time required: About 4 minutes)

6-1 Remove the lower case assembly. (See procedure 1.)
6-2 Remove the encoder knob from the control panel.
(Fig. 6)
6-3 Remove the four (4) screws marked [380F]. The ENC
circuit board can then be removed. (Fig.4)
[380L]

LCD Unit

(液晶ユニット)
[380L]:BindHeadTappingScrew-B3.0X8MFZN2W3(WE774301) Bタイト +BIND
Fig.5(図5)
Upper Case Assembly
(上ケースAss'y)
6. ENCシート (所要時間:約4分)
6-1 下ケースAss'yを外します。(1項参照) 6-2 コントロールパネル面からエンコーダツマ ミ を外 し ま す。
(図6)
6-3 [380F]のネジ4本を外し、ENCシートを外し ま す。(図4)
Encoder knob
(エンコーダツマミ)
Fig.6(図6)
11
PSR-S550/PSR-S550B

7. PSW Circuit Board (Time required: About 3 minutes)

7-1 Remove the lower case assembly. (See procedure 1.)
7-2 Remove the two (2) screws marked [380C]. The PSW
circuit board can then be removed. (Fig.3)
7-3 Pull out the push knob (black) from the PSW circuit
board. (Fig.2)

8. TW Circuit Board, Speaker (Tweeter) (Time required: About 3 minutes each)

8-1 Remove the lower case assembly. (See procedure 1.)
8-2 Remove the two (2) screws marked [380D]. The speaker
(tweeter) can then be removed. (Fig.3)
* The tweeters L and R can be removed in the same
manner.

9. Wheel Assembly, PB, MVR, PNL, PNC, PNR Circuit Boards

9-1 Remove the lower case assembly. (See procedure 1.)
9-2 Remove the two (2) screws marked [80B]. (Fig.2)
9-3 Remove the screw marked [100B]. The 16N keyboard
assembly and the lower key bed assembly can then be
removed. (Fig.3)
7. PSWシート (所要時間:約3分)
7-1 下ケースAss'yを外します。(1項参照) 7-2 [380C]のネジ2本を外し、PSWシートを外し ま す。(図3) 7-3 PSWシートからプッシュツマミ(黒)を外します 。(図2)
8. TWシート、スピーカ(ツイーター) (所要時間:各約3分)
8-1 下ケースAss'yを外します。(1項参照) 8-2 [380D]のネジ2本を外し、スピーカ(ツ イー タ ー)を外 し ます。
(図3)
*左ーターは、それぞれ同じ方法で外すことができ ま
す。
9. ホイールAss'y、PB、MVR、PNL、PNC、PNR
シート
9-1 下ケースAss'yを外します。(1項参照) 9-2 [80B]のネジ2本を外します。(図2) 9-3 [100B]のネジ1本を外し、16N鍵盤Assy、下ケ ー ス 鍵盤
Ass'yを外します。(図3)

9-4 Wheel Assembly, PB Circuit Board

(Time required: About 4 minutes each)
9-4-1 Remove the two (2) screws marked [380G]. The wheel
assembly with the PB circuit board can then be removed.
9-4-2 Remove the PB circuit board from the wheel assembly.
(Fig. 4)

9-5 MVR Circuit Board

(Time required: About 4 minutes)
9-5-1 Remove the volume knob from the control panel. (Fig.7)
9-5-2 Remove the three (3) screws marked [380H]. The MVR
circuit board can then be removed. (Fig.4)

9-6 PNL Circuit Board

(Time required: About 5 minutes)
9-6-1 Remove the thirteen (13) screws marked [380I].
The PNL circuit board can then be removed. (Fig.4)
9-4 ホイールAss'y、PBシート
(所要時間:約4分)
9-4-1 [380G]のネジ2本を外し、ホイールAss'yと共にPBシートを外
します。(図4)
9-4-2 ホイールAss'yから、PBシートを外し ま す。(図4)
9-5 MVRシート
(所要時間:約4分)
9-5-1 コントロールパネル面からボリ ュームツマミ を外 し ま す。(図7) 9-5-2 [380H]のネジ3本を外し、MVRシートを外し ま す。(図4)
9-6 PNLシート
(所要時間:約5分)
9-6-1 [380I]のネジ13本を外し、PNLシートを外 し ま す。(図4)
Volume Knob
(ツマミ(マスターボリューム))
Cloth
(布)
12
Fig.7(図7)
PSR-S550/PSR-S550B

9-7 PNC Circuit Board

(Time required: About 6 minutes)
9-7-1 Remove the AM circuit board. (See procedure 2.)
9-7-2 Remove the DM circuit board. (See procedure 4.)
9-7-3 Remove the ten (10) screws marked [380J]. The PNC
circuit board can then be removed. (Fig.4)

9-8 PNR Circuit Board

(Time required: About 5 minutes)
9-8-1 Remove the eleven (11) screws marked [380K]. The
PNR circuit board can then be removed. (Fig.4)

10. Speaker (Woofer) (Time required: About 3 minutes each)

10-1 Remove the lower case assembly. (See procedure 1.)
10-2 Remove the four (4) screws marked [40]. The speaker
(woofer) can then be removed. (Fig.3)
*The woofers L and R can be removed in the same
manner.

11. Disassembling 16N Keyboard Assembly

11-1 Remove the lower case assembly. (See procedure 1.)
11-2 Remove the two (2) screws marked [80B]. (Fig.2)
11-3 Remove the screw marked [100B]. The 16N keyboard
assembly and the lower key bed assembly can then be
removed. (Fig.3)
9-7 PNCシート
(所要時間:約6分)
9-7-1 AMシートを外し ま す。(2項参照) 9-7-2 DMシートを外し ま す。(4項参照) 9-7-3 [380J]のネジ10本を外し、PNCシートを外し ま す。(図4)
9-8 PNRシート
(所要時間:約5分)
9-8-1 [380K]のネジ11本を外し、PNRシートを外し ま す。(図4)
10. スピーカ(ウーファー) (所要時間:各約3分)
10-1 下ケースAss'yを外します。(1項参照) 10-2 [40]のネジ 4本を 外し、スピーカ(ウー フ ァー)を外し ま す。(図3) *左ァーは 、それぞれ同 じ方法で外すことがで きま
す。
11. 16N鍵盤Ass'yの分解
11-1 下ケースAss'yを外します。(1項参照) 11-2 [80B]のネジ2本を外します。(図2) 11-3 [100B]のネジ1本を外し、16N鍵盤Ass'y、下ケー ス 鍵盤
Ass'yを外します。(図3)

11-4 White Keys and Black Keys

11-4-1 White and black keys for one octave unit are integrated
as a set. There are five sets in total.
Only the C6 white key, unlike the other keys, is not
integrated in a set. (Fig. 8)
11-4-2 To remove a set, remove the four (4) each screws marked
[120A]. The white and black keys in the set can then be
removed. (Fig. 8)
When removing, unfasten the two (2) hooks at the back
of the black keys upward, and lift the white and black
keys while pulling them toward you a little. (Fig.9)
11-4-3 To remove the white key C6, remove the screw marked
[120B], unhook as described in Procedure 11-4-2, and
pull out toward you. (Fig. 8)

11-5 Rubber Contact

11-5-1 Remove the white and black keys corresponding to the
rubber contacts to be removed. (Fig.8, Photo.1)
11-5-2 Remove the rubber contacts. (Fig.8, Photo.1)

11-6 61L Circuit Board (MK-L)

(Time required: About 7 minutes)
11-6-1 Remove the white and black keys from C1 to B3. (See
Fig.8 and Procedure 11-4.)
11-6-2 Remove the four (4) screws marked [100A] and the eight
(8) screws marked [110A]. The 61L circuit board (MK-
L) can then be removed. (Fig.8)
11-4 白鍵、黒鍵
11-4-1 白鍵、黒鍵は、左側から1オクターブ 単 位のセッ トになっ てい
て、全部で5セットあります。 C6鍵は、白鍵1個のみです。(図8)
11-4-2 セットのものは、 [120A]のネジ4本づつ外してそれぞれ1セッ
ト分の白鍵、黒鍵を外します。(図8)
この時、黒鍵の後ろ側にある2つのフックを上方向に外し、 白鍵・黒鍵を少し手前に引きなが ら持ち上げま す。(図9)
11-4-3 C6の白鍵は[120B]のネジ1本を外し、11-4-2項のようにフッ
クを外 して手前に引 きながら外 し ま す。(図8)
11-5 接点ゴム
11-5-1 外そうとする接 点ゴムに対 応した白 鍵 ・黒鍵を外します。
(図8、写真1)
11-5-2 それぞれの接点ゴムを外します。(図8、写真1)
11-6 シート61L(MK-L)
(所要時間:約7分)
11-6-1 C1〜B3の白鍵・黒鍵を外します。(図8、11-4項参照) 11-6-2 [100A]のネジ4本と[110A]のネジ8本を外し、シー ト61L
(MK-L)を外 し ます。(図8)
13
PSR-S550/PSR-S550B
Rubber Contact 12P
(接点ゴム
Lower Key Bed Assembly
(下ケース鍵盤Ass'y)
[120A]
12P
)
[100A]
[110A]
[120A]
Rubber Contact 12P
(接点ゴム
(16N-C61鍵盤Ass'y)
[120A]
12P
Keyboard Assembly
)
[120A]
[100B]
Rubber Contact 13P
(接点ゴム
61H61L
[110B]
[120A]
[120B]
13P
)
C1 C2 B2 C3 B3 C4 B4 C5 B5 C6B1
One octave
(1オクターブ)
(C1-B1)
[100]: BindHeadTappingScrew-B3.0X8MFZN2W3(WE774301)Bタイト+BIND [110]: BindHeadTappingScrew-P3.0X12MFZN2W3SP(WH899400)Pタイト+BIND [120]: BindHeadTappingScrew-P3.0X20MFZN2W3(WF49200R)Pタイト+BIND
Hook
(フック)
One octave
(1オクターブ)
(C2-B2)
One octave
(1オクターブ)
(C3-B3)
Fig.8(図8)
Rubber contact
(接点ゴム)
61H
One octave
(1オクターブ)
(C4-B4)
One octave
(1オクターブ)
(C5-B5)
C6 Key
(C6鍵)
14
Fig.9(図9)
* When installing the 61L circuit board (MK-L), tighten
the screws 1 through 12 in numerical order as shown
in the figure "61L" in Fig.10. (Fig.10)
PSR-S550/PSR-S550B
**
シシ
ーー
トト
61L61L
((
MK-LMK-L
))
をを
取取
りり
付付
けけ
るる
時時
はは
、、
図図
1010
のの
シシ
ーー
ささ
ささ
のの
いい
いい
シシ
。。
。。
ーー
トト
トト
*
61L
MK-L
締締
締締
はは
めめ
めめ
、、
図図 てて
てて
10
1010 下下
下下
**
シシ
ーー
トト
61L61L
((
MK-LMK-L
))
をを
取取
りり
付付
けけ
るる
時時
61L61L
図図
のの
番番
号号
11
〜〜
1212
のの
順順
にに
ネネ
ジジ
61L
61L61L
((
((
図図
図図
図図
1010
10
1010
のの ))
))
番番
号号
1
12
〜〜
1212
のの
順順
11
にに
ネネ
ジジ
をを
をを

11-7 61H Circuit Board (MK-H)

(Time required: About 6 minutes)
11-7-1 Remove the white and black keys from C4 to C6. (See
Fig.8 and Procedure 11-4.)
11-7-2 Remove the three (3) screws marked [100B] and the five
(5) screws marked [110B]. The 61H circuit board (MK-
H) can then be removed. (Fig.8)
*When installing the 61H circuit board (MK-H),
tighten the screws 1 through 8 in numerical order as
shown in the figure "61H" in Fig.10. (Fig. 10)
61H
11-7 シート61H(MK-H)
(所要時間:約6分)
11-7-1 C4〜C6の白鍵・黒鍵を外します。(図8、11-4項参照) 11-7-2 [100B]のネジ3本と[110B]のネジ5本を外し、シー ト61H
(MK-H)を外 し ます。(図8)
**
シシ
ーー
トト
61H61H
((
MK-HMK-H
))
をを
取取
りり
付付
けけ
るる
時時
はは
、、
*
**
((
((
Rubber contact
(接点ゴム)
シシ
ーー
61H61H
61H
61H61H
図図
図図
トト
1010
10
1010
61H
61H61H
図図
図図
))
))
のの
のの
MK-H
((
MK-HMK-H
番番
番番
号号
号号
りり にに
にに
付付
ネネ
ネネ
けけ ジジ
ジジ
をを
をを
るる
))
をを
取取
11
〜〜
88
のの
順順
1
8
11
〜〜
88
のの
順順
時時 締締
締締
はは めめ
めめ
てて
てて
、、
図図
図図
下下
下下
1010
10
1010
ささ
ささ
のの
のの いい
いい
シシ
シシ
。。
。。
ーー
ーー
トト
トト
Photo.1(写真1)
61H61L
9 678
2456
3
10 11 12
811 3 4 5 27
Fig.10(図10)
15
PSR-S550/PSR-S550B

LSI PIN DESCRIPTION(LSI端子機能表)

CONTENTS(目次)
AK4385ET (X6040A01) DAC ....................................................................................... 16
MN101C027YB (XS71120R) CPU ............................................................................... 16
R8A0232BG (X8810A00) CPU (SWX02) ..................................................................... 17
S1D13700F01A100 (X5422A00) LCD CONTROLLER ............................................... 19
UPD789022GB-A15-8E (XZ56010R) CPU (MKS) ....................................................... 19
AK4385ET (X6040A01) DAC (Digital to Analog Converter)
PIN
NAME I/O FUNCTION
NO.
1 MCLK I Master Clock 9 AOUTR- O Rch Analog out(-) 2BICK I Audio Serial Data Clock 10 AOUTR+ O Rch Analog out(+) 3 SDTI I Audio Serial Date Input 11 AOUTL- O Lch Analog out(-) 4 LRCK I L/R Clock 12 AOUTL+ O Lch Analog out(+) 5 PDN I Power Down mode 13 Vss - Ground 6 CSN I Chip Select 14 VDD - Power Supply 7 CCLK I Control Data Input 15 DZFR O Rch Data Zero Input Detect 8 CDTI I Control Data Input 16 DZFL O Lch Data Zero Input Detect
PIN
NAME I/O FUNCTION
NO.
MN101C027YB (XS71120R) CPU
PIN
NO.
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
1 2 3 4 5 6 7 8 9
S1 S2 S3 S4 S5
VREF+
VDD OSC2 OSC1
VSS
XI
XO
MMOD
RD0
RXD
D0 D1 D2 D3 D4
/RST
D5 D6 D7 D8 D9 S6 S7 S8
S9 S10 S11
I/O FUNCTIONNAME
I I I I I
-
-
O
I
­I
O
I
O
I O O O O O
I O O O O O
I
I
I
I
I
I
Switch matrix data
Power supply (+5V, analog) Power supply (+5V) Crystal oscillator (8MHz) Crystal oscillator (8MHz) Ground Not used Not used Memory mode select (Grounded) Rotary encoder data MIDI receive data
LED and switch drive data
Reset
LED and switch drive data
Switch matrix data
PIN NO.
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
S12 S13 S14 TXD S15 S16 S17 S18
L16 L17 L18 L19
L8
L9 L10 L11 L12 L13 L14 L15
L7
L6
L5
L4
L3
L2
L1
L0
VREF
AD0 AD1
S0
I/O FUNCTIONNAME
I I
Switch matrix data
I
O
O O O O O O O O O O O O O O O O O O O O
-
MIDI transmit data I I
Switch matrix data I
I
LED drive data
LED and switch drive data
Grounded
Analog input
I
Analog input
I I
Switch matrix data
DM: IC14
PNL:IC101
16
PSR-S550/PSR-S550B
R8A02032BG
PIN
OUTER
NO.
NO.
VSS
A1
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79
1 2 3 4 5 6 7 8 9
A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20
B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20
C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20
D10 D11 D12 D13 D14 D15 D16 D17 D18 D19
AN2
A2
AN1
A3
VSS
A4
RxD1
A5
SCK1
A6
UCLK
A7
VSS
A8 A9
FUNC_DM
VSS HOST_DM POWER_ENB
XTAL
EXTAL
VSS CS7N/PJ6
TRSTN
TDI
TCK
VCCQ
B1
MD15
B2
VSS
B3
AN3
B4
AN0
B5
VSS
B6
TxD1
B7
TxD0
B8
VSS
B9
FUNC_DP
VSS HOST_DP
SCL VSS VSS
CS4N/PJ3 TIOC0A/PJ7
TESTN
TMS
VCCQ VCCQ
C1
MD13
C2
MD14
C3
VSS
C4
VREFADC
C5
VSSADC
C6
VSS
C7
RxD0
C8
VSS
C9
VBUS
VSS
OVER_CURRENT_N
SDA
CS0N CS2N/PJ1 CS5N/PJ4
ASEMDN
TDO
VCCQ VDDPLL VDDPLL
D1
MD10
D2
MD11
D3
MD12
D4
VSS
D5
VCCADC
D6
VSS
D7
RESN
D8
VCCQ
D9
PULLUP_ENB
VCCQ
UCTL
EICN CS1N/PJ0 CS3N/PJ2 CS6N/PJ5 ASEBRKAKN
VCCQ VCCQ
VSSPLL
(
X8810A00) CPU
I/O FUNCTIONNAME
-
Ground
I
ADC analog input 2
I
ADC analog input 1
-
Ground
I
Serial input 1
I
External sync. clock input 1
I
USB external clock input (48 MHz)
-
I/O
I/O
I/O
I/O
I/O I/O
I/O I/O
I/O
I/O I/O I/O
I/O
Ground USB function data -
-
Ground USB host data -
O
USB voltage enable
O
Crystal oscillator output
I
Crystal oscillator input (16.9344 MHz)
-
Ground
O
SH2A-CPU chip select 7
I
JTAG test reset input
I
JTAG test data input
I
JTAG test clock input
-
Power supply +3.3 V Wave memory data bus 15
-
Ground
I
ADC analog input 3
I
ADC analog input 0
-
Ground
O
Serial output 1
O
Serial output 0
-
Ground USB function data +
-
Ground USB host data + E bus (I2C) clock input/output (5V compatible)
­Ground
-
O
SH2A-CPU chip select 4
O
PWM output
I
Test input
I
JTAG test mode select input
­Power supply +3.3 V
­Wave memory data bus 13 Wave memory data bus 14
-
Ground
-
ADC reference power supply +3.3 V
-
ADC analog ground
-
Ground
I
Serial input 0
-
Ground
I
USB cable connection monitor (5V compatible)
-
Ground
I
USB overcurrent detection (5V compatible) E bus (I2C) data input/output (5V compatible)
O
SH2A-CPU chip select 0
O
SH2A-CPU chip select 2
O
SH2A-CPU chip select 5
I
Debug mode configuration
O
JTAG test data output
-
Power supply +3.3 V
­PLL analog power supply +1.2 V
­Wave memory data bus 10 Wave memory data bus 11 Wave memory data bus 12
-
Ground
-
ADC analog power supply +3.3 V
-
Ground
I
Hardware reset
-
Power supply +3.3 V
O
USB pull-up enable
-
Power supply +3.3 V
I
USB output control
O
E bus reset output
O
SH2A-CPU chip select 1
O
SH2A-CPU chip select 3
O
SH2A-CPU chip select 6 Emulator break
­Power supply +3.3 V
-
-
PLL analog ground
(
SWX02)
PIN NO.
80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98
99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158
OUTER
NO.
D20
E1 E2 E3 E4 E5 E6 E7 E8
E9 E10 E11 E12 E13 E14 E15 E16 E17 E18 E19 E20
F1 F2 F3 F4
F5 F16 F17 F18 F19 F20
G1 G2 G3 G4
G5 G16 G17 G18 G19 G20
H1
H2
H3
H4
H5 H16 H17 H18 H19 H20
J1 J2 J3 J4 J5
J9 J10 J11 J12 J16 J17 J18 J19 J20
K1 K2 K3 K4 K5
K9 K10 K11 K12 K16 K17 K18 K19 K20
VSSPLL
MD6 MD7 MD8 MD9 VDD VDD
VSS
VCCQ
VSS VCCQ VCCQ
VSS VCCQ
VSS
VDD
VDD D31/PF7 D30/PF6 D29/PF5 D28/PF4
MD2
MD3
MD4
MD5
VDD
VDD D27/PF3 D26/PF2 D25/PF1 D24/PF0
MA2
MA1 MD0 MD1
VSS
VSS
D23/PE7 D22/PE6 D21/PE5 D20/PE4
MA6
MA5
MA4
MA3
VCCQ
VCCQ D19/PE3 D18/PE2
VCCQ
VCCQ
MA10
MA9 MA8 MA7 VSS VSS VSS VSS VSS
VSS D17/PE1 D16/PE0
CKOEN
CKIO MA14 MA13 MA12 MA11
VDD
VSS
VSS
VSS
VSS
VDD
CKE
D15 VSS VSS
I/O FUNCTIONNAME
I/O I/O I/O I/O
I/O I/O I/O I/O I/O I/O I/O I/O
I/O I/O I/O I/O
O
O I/O I/O
I/O I/O I/O I/O
O
O
O
O
I/O I/O
O
O
O
O
I/O I/O
O
O
O
O
O
O I/O
PLL analog ground
­Wave memory data bus 6 Wave memory data bus 7 Wave memory data bus 8 Wave memory data bus 9
­Power supply +1.2 V
­Ground
­Power supply +3.3 V
­Ground
-
­Power supply +3.3 V
­Ground
­Power supply +3.3 V
­Ground
-
­Power supply +1.2 V
­SH2A-CPU data bus 31 SH2A-CPU data bus 30 SH2A-CPU data bus 29 SH2A-CPU data bus 28 Wave memory data bus 2 Wave memory data bus 3 Wave memory data bus 4 Wave memory data bus 5
­Power supply +1.2 V
­SH2A-CPU data bus 27 SH2A-CPU data bus 26 SH2A-CPU data bus 25 SH2A-CPU data bus 24 Wave memory address bus 2 Wave memory address bus 1 Wave memory data bus 0 Wave memory data bus 1
­Ground
­SH2A-CPU data bus 23 SH2A-CPU data bus 22 SH2A-CPU data bus 21 SH2A-CPU data bus 20 Wave memory address bus 6 Wave memory address bus 5 Wave memory address bus 4 Wave memory address bus 3
­Power supply +3.3 V
­SH2A-CPU data bus 19 SH2A-CPU data bus 18
­Power supply +3.3 V
­Wave memory address bus 10 Wave memory address bus 9 Wave memory address bus 8 Wave memory address bus 7
-
-
­Ground
-
-
­SH2A-CPU data bus 17 SH2A-CPU data bus 16 Clock output control for SDRAM
I
Clock output for SDRAM Wave memory address bus 14 Wave memory address bus 13 Wave memory address bus 12 Wave memory address bus 11 Power supply +1.2 V
-
-
­Ground
-
­Power supply +1.2 V
­Clock enable for SDRAM SH2A-CPU data bus 15
­Ground
-
DM: IC7
17
PSR-S550/PSR-S550B
PIN NO.
159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237
OUTER
NO.
MA15
L1
MA16
L2
MA17
L3
MA18
L4
VDD
L5
VSS
L9
VSS
L10
VSS
L11
VSS
L12
VDD
L16 L17 L18 L19 L20
M10 M11 M12 M16 M17 M18 M19 M20
N16 N17 N18 N19 N20
P16 P17 P18 P19 P20
R16 R17 R18 R19 R20
T10 T11 T12 T13 T14 T15 T16 T17 T18 T19 T20
D11 D12 D13 D14
MA19
M1
MA20
M2
MA21
M3
MA22
M4
VSS
M5
VSS
M9
VSS VSS VSS VSS
D10
N1
MA23/PG4
N2
MA24/PG5
N3
MA25/PG6
N4
MA26/PG7
N5
VCCQ VCCQ
P1
MCS3N/PG3
P2
MCS2N/PG2
P3
MCS1N/PG1
P4
MWRN/PG0
P5
VSS VSS
RD/WRN
R1
MCS0N
R2
MRDN
R3
BTCHG
R4
PA0
R5
VDD VDD
WE3N/DQMUU/PH3
RASLN CASLN
RDN
T1
PA1
T2
PA2
T3
PA3
T4
PA4
T5
VDD
T6
VDD
T7
VSS
T8
VCCQ
T9
VSS VCCQ VCCQ
VSS VCCQ
VSS
VDD
VDD
A0/PH4
WE0N/DQMLL/PH0 WE1N/DQMLU/PH1 WE2N/DQMUL/PH2
U1
PA5
D7 D8 D9
D3 D4 D5 D6
D0 D1 D2
I/O FUNCTIONNAME
I/O I/O I/O I/O
I/O I/O I/O I/O
I/O I/O I/O I/O
I/O I/O I/O
I/O
I/O I/O I/O I/O
I/O
PIN NO.
O
Wave memory address bus 15
O
Wave memory address bus 16
O
Wave memory address bus 17
O
Wave memory address bus 18
-
Power supply +1.2 V
-
­Ground
-
-
-
Power supply +1.2 V SH2A-CPU data bus 11 SH2A-CPU data bus 12 SH2A-CPU data bus 13 SH2A-CPU data bus 14
O
Wave memory address bus 19
O
Wave memory address bus 20
O
Wave memory address bus 21
O
Wave memory address bus 22
-
-
­Ground
-
-
­SH2A-CPU data bus 7 SH2A-CPU data bus 8 SH2A-CPU data bus 9 SH2A-CPU data bus 10
O
Wave memory address bus 23
O
Wave memory address bus 24
O
Wave memory address bus 25
O
Wave memory address bus 26
­Power supply +3.3 V
­SH2A-CPU data bus 3 SH2A-CPU data bus 4 SH2A-CPU data bus 5 SH2A-CPU data bus 6
O
Wave memory chip select 3
O
Wave memory chip select 2
O
Wave memory chip select 1
O
Wave memory write enable
­Ground
-
O
SH2A-CPU read/write enable SH2A-CPU data bus 0 SH2A-CPU data bus 1 SH2A-CPU data bus 2
O
Wave memory chip select 0
O
Wave memory read enable
I
BOOT ROM switching control Parallel port A0
­Power supply +1.2 V
-
O
Writing byte of D31 - D24/Selecting D31 - D24 in case of SDRAM
O
RAS output for SDRAM
O
CAS output for SDRAM
O
SH2A-CPU read enable Parallel port A1 Parallel port A2 Parallel port A3 Parallel port A4
­Power supply +1.2 V
-
-
Ground
-
Power supply +3.3 V
-
Ground
­Power supply +3.3 V
-
-
Ground
-
Power supply +3.3 V
-
Ground
­Power supply +1.2 V
-
O
SH2A-CPU address bus 0
O
Writing byte of D7 - D0/Selecting D7 - D0 in case of SDRAM
O
Writing byte of D15 - D8/Selecting D15 - D8 in case of SDRAM
O
Writing byte of D23 - D16/Selecting D23 - D16 in case of SDRAM Parallel port A5
238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316
OUTER
NO.
U2 U3 U4 U5 U6 U7 U8
U9 U10 U11 U12 U13 U14 U15 U16 U17 U18 U19 U20
V1
V2
V3
V4
V5
V6
V7
V8
V9 V10 V11 V12 V13 V14 V15 V16 V17 V18 V19 V20
W1 W2 W3 W4 W5 W6 W7 W8
W9 W10 W11 W12 W13 W14 W15 W16 W17 W18 W19 W20
Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8
Y9 Y10 Y11 Y12 Y13 Y14 Y15 Y16 Y17 Y18 Y19 Y20
PA6 PA7
VCCQ ED1/PC1 ED5/PC5 ED9/PD1
ED13/PD5
EA2/PK1
ECSN
BCLK
IRQ0
A25 A21 A17 A13
VCCQ
A3 A2
A1 PB0 PB1
VCCQ
PB6
ED2/PC2
ED6/PC6 ED10/PD2 ED14/PD6
EA3/PK2
SDI0/PK5 WCLK2/SDO2
IRQ1 BW_MD0 A22/PH5
A18 A14 A10
VCCQ
A5 A4
PB2
VCCQ
PB4
PB7 ED3/PC3 ED7/PC7
ED11/PD3 ED15/PD7 ERDN/PK3 SDI1/PK6
WCLK SYSCLK2 WAITN/PK7
A23/PH6
A19 A15 A11
A8
VCCQ
A6
VCCQ
PB3
PB5 ED0/PC0 ED4/PC4 ED8/PD0
ED12/PD4
EA1/PK0
EWRN/PK4
SDO0 SDO1
SYSCLK
SYI
A24/PH7
A20
A16
A12
A9 A7
VCCQ
I/O FUNCTIONNAME
I/O I/O
I/O I/O I/O I/O
I/O I/O
I/O I/O I/O I/O I/O
I/O
I/O I/O I/O I/O I/O I/O
I/O I/O I/O I/O I/O I/O
Parallel port A6 Parallel port A7
-
Power supply +3.3 V External CPU data bus 1 External CPU data bus 5 External CPU data bus 9 External CPU data bus 13
I
External CPU address bus 2
I
O
O O O O
O O O
O
O O O O
O O
O O
O O O O O
O
O O O
O O O O O O
External CPU chip select Bit clock output
I
Interrupt input 0 SH2A-CPU address bus 25 SH2A-CPU address bus 21 SH2A-CPU address bus 17 SH2A-CPU address bus 13
-
Power supply +3.3 V SH2A-CPU address bus 3 SH2A-CPU address bus 2 SH2A-CPU address bus 1 Parallel port B0 Parallel port B1
-
Power supply +3.3 V Parallel port B6 External CPU data bus 2 External CPU data bus 6 External CPU data bus 10 External CPU data bus 14
I
External CPU address bus 3
I
Serial audio input 0 Word clock output 2/Serial audio output 2
I
Interrupt input 1
I
SH2A-CPU data bus width configuration SH2A-CPU address bus 22 SH2A-CPU address bus 18 SH2A-CPU address bus 14 SH2A-CPU address bus 10
-
Power supply +3.3 V SH2A-CPU address bus 5 SH2A-CPU address bus 4 Parallel port B2
-
Power supply +3.3 V Parallel port B4 Parallel port B7 External CPU data bus 3 External CPU data bus 7 External CPU data bus 11 External CPU data bus 15
I
External CPU read enable
I
Serial audio input 1 Word clock output Clock output 2
I
External wait input SH2A-CPU address bus 23 SH2A-CPU address bus 19 SH2A-CPU address bus 15 SH2A-CPU address bus 11 SH2A-CPU address bus 8
-
Power supply +3.3 V SH2A-CPU address bus 6
-
Power supply +3.3 V Parallel port B3 Parallel port B5 External CPU data bus 0 External CPU data bus 4 External CPU data bus 8 External CPU data bus 12
I
External CPU address bus 1
I
External CPU write enable Serial audio output 0 Serial audio output 1 Clock output
I
Sync. input from external device SH2A-CPU address bus 24 SH2A-CPU address bus 20 SH2A-CPU address bus 16 SH2A-CPU address bus 12 SH2A-CPU address bus 9 SH2A-CPU address bus 7
-
Power supply +3.3 V
18
PSR-S550/PSR-S550B
S1D13700F01A100 (X5422A00) LCD CONTROLLER
PIN
NO.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
VSS AB12 AB11 AB10
AB9
AB8
HIOVDD
AB7
AB6
AB5
AB4
COREVDD
AB3
AB2
AB1
AB0
VSS
FPDAT3 FPDAT2 FPDAT1 FPDAT0 NIOVDD
FPSHIFT
XECL
COREVDD
FPLINE
MOD
VSS
YSCL
FPFRAME
YDIS
NIOVDD
I/O FUNCTIONNAME
I I I I I
I I I I
I I I I
O O O O
O O
O O
O O O
Ground
Address bus
Power supply
Address bus
Power supply
Address bus
Ground
Data bus
Power supply Shift clock X driver enable chain clock Power supply Latch pulse Frame signal Ground Scan shift clock Scan start pulse LCD power-down output Power supply
PIN NO.
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
VSS XCD1 XCG1
RESET#
SCANEN
TESTEN
CLKI
COREVDD
RD#
WR#
CS#
DB7
DB6
DB5
DB4
HIOVDD
DB3
DB2
DB1
DB0
VSS
WAIT#
HIOVDD
CNF0 CNF1 CNF2 CNF3 CNF4
AS#
AB15 AB14 AB13
I/O FUNCTIONNAME
O
I/O I/O I/O I/O
I/O I/O I/O I/O
O
DM: IC4
I I I I I
I I I
I I I I I I I I I
Ground Drain output Gate input Reset
Test mode set up input
Externally sourced system clock Power supply Read strobe Write strobe Chip select
Data bus
Power supply
Data bus
Ground Wait output Power supply
Input pin for S1D 13700 setting
Address strobe
Address bus
UPD789022GB-A15-8E (XZ56010R) CPU (MKS)
PIN NO.
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16 17 18 19 20 21 22
P47/KR7 P46/KR6 P45/KR5 P44/KR4 P43/KR3 P42/KR2 P41/KR1 P40/KR0
VSS0 VDD0
/RESET
P51/TO2 P50/TI0/TO0
P12 P11 P10
NC
IC X2 X1
P53 P52
I/O FUNCTIONNAME
I/O I/O
Port 1 I/O I/O I/O I/O I/O
Port 4/Key return signal detection input I/O
I/O I/O I/O
Internally connected (N.C.)
Clock
I
Ground
Power supply
System reset
I
I/O
Port 5 I/O
Port 5/16-bit timer output
I/O
Port 5/External count clock input to 8-bit timer/8-bit timer output
I/O
PIN
NO.
23
P32/INTP2/CPT2
P31/INTP1
24
P30/INTP0
25 26
P22/RXD/SI0
27
P21/TXD/SO0
28
P20/ASCK//SCK0
P07
29
P06
30
P05
31
P04
32
P03
33
P02
34
P01
35
P00
36
NC
37
VDD1
38
VSS1
39
P17
40 41
P16
42
P15
43
P14
44
P13
DM: IC17
I/O FUNCTIONNAME
Port 3/External interrupt input/Capture edge input
I/O I/O
Port 3/External interrupt input
I/O
Port 2/Asynchronous serial interface serial data input/Serial interface serial data input
I/O
Port 2/Asynchronous serial interface serial data output/Serial interface serial data output
I/O
Port 2/Asynchronous serial interface serial clock input/Serial interface serial clock
I/O I/O I/O I/O I/O
Port 0
I/O I/O I/O I/O
Power supply
Ground I/O I/O
Port 1
I/O I/O I/O
19
PSR-S550/PSR-S550B

IC BLOCK DIAGRAM(IC ブロック図)

SN74LV08APWR (X4463A00)
DM: IC13
SN74AHCT08PWR (X3824A00)
DM: IC24
Quad 2 Input AND
1
VSS
1A
1B
2
1Y
3
4
2A
5
2B
6
2Y
7
14
VDD
4B
13
4A
12
11
4Y
10
3B
9
3A
8
3Y
LA4625 (XY209A0R) Power Amplifier 13.5W
AM: IC201
DC
2
RIPPLE FILTER
PREDRIVER
+
1
IN1
PRE-GND
STBY
IN2
IN
-
BIAS
3
CIRCUIT
STANDBY
4
SW
+
6
IN
-
POP NOISE PREVENTION CIRCUIT
5
ON TIME POP
PREDRIVER
PREDRIVER
PREDRIVER
OVER VOLTAGE/
SURGE
THERMAL
SHUT DOWN
7
POWER
POWER
POWER
POWER
SN74LV14APWR (X6688A0R) Hex Inverter
DM: IC20
LOAD SHORT PROTECTOR
LOAD SHORT PROTECTOR
OUTPUT PIN TO V SHORT PROTECTOR
OUTPUT PIN TO GND SHORT PROTECTOR
V
CC
OUTPUT PIN TO GND SHORT PROTECTOR
OUTPUT PIN TO V SHORT PROTECTOR
V
GND
CC
14
1A
1Y
2A
2Y
3A
3Y
POWER GND1
POWER GND2
CC
CC
1
2
3
4
5
6
7
13
-OUT1
12
PWR-GND1
11
+OUT1
-OUT2
9
10
PWR-GND2
8
+OUT2
14
13
12
11
10
9
8
VDD
6A
6Y
5A
5Y
4A
4Y
NJM4580E(TE2) (X2331A0R) Dual Operational Amplifier
DM: IC16
Output A
Inverting
Input A
Non-Inverting
Input A
-DC Voltage Supply
1
2
3
4-V
+-
+-
+DC Voltage
8
+V
Supply
7
Output B
Inverting
6
Input B
Non-Inverting
5
Input B
MC34063EBD-TR (X7371A00) DC-DC Converter
DM: IC19
Drive
Collector
I
pk
Sense
V
CC
Comparator
Inverting
Input
8
7
6
5
I
pk
Oscillator
Comparator
+
±
SQ
R
C
T
100
Reference
Regulator
1
Q2
Q1
2
3
1.25 V
4
Switch Collector
Switch Emitter
Timing Capacitor
Gnd
R5520H001B-T1-F
USB High-Side Power Switch
DM: IC18
EN
1 5
2
GND
3
FLG
20
(X7569A00)
OUT
4
IN
4
IN
UVLO
THERMAL
GATE
CONTROL
1
EN
SHUTDOWN
CURRENT
LIMIT
FLAG
DELAY
2
GND
5
OUT
3
FLG

CIRCUIT BOARDS(シート基板図)

CONTENTS(目次)
61H Circuit Board (X2335C0) ....................................................................................... 32
61L Circuit Board (X2336B0) ........................................................................................ 32
AM Circuit Board (X7722C0) ........................................................................................ 24
DM Circuit Board (X9574B0) ........................................................................................ 22
ENC Circuit Board (X7722C0) ...................................................................................... 25
JACK Circuit Board (X7722C0) ..................................................................................... 25
MVR Circuit Board (X7722C0) ...................................................................................... 24
PB Circuit Board (X7722C0) ......................................................................................... 24
PNC Circuit Board (X7978B0) ...................................................................................... 28
PNL Circuit Board (X7723D0) ....................................................................................... 26
PNR Circuit Board (X7978B0) ...................................................................................... 30
PSW Circuit Board (X7722C0) ..................................................................................... 25
TW Circuit Board (X7722C0) ........................................................................................ 25
PSR-S550/PSR-S550B
Note: See parts list for details of circuit board component parts.
注:シートの部品詳細はパーツリストをご参照ください。
21
Loading...
+ 48 hidden pages