WASHER |
INSTRUCTIONS |
INSTALLATION |
D’INSTALLATION |
INSTRUCTIONS |
DE LA LAVEUSE |
|
|
Table of Contents |
|
WASHER SAFETY.......................................................... |
1 |
INSTALLATION REQUIREMENTS................................ |
2 |
Tools and Parts................................................................ |
2 |
Alternative Parts.............................................................. |
2 |
Location Requirements................................................... |
3 |
Drain System.................................................................... |
4 |
Electrical Requirements.................................................. |
5 |
INSTALLATION INSTRUCTIONS.................................. |
5 |
Connect Drain Hose........................................................ |
6 |
Connect Inlet Hoses........................................................ |
7 |
Level Washer.................................................................... |
8 |
Complete Installation Checklist..................................... |
9 |
Table des matières |
|
SÉCURITÉ DE LA LAVEUSE....................................... |
10 |
EXIGENCES D’INSTALLATION................................... |
10 |
Outillage et pièces......................................................... |
10 |
Autres pièces.................................................................. |
10 |
Exigences d’emplacement............................................ |
11 |
Système de vidange...................................................... |
13 |
Spécifications électriques............................................. |
13 |
INSTRUCTIONS D’INSTALLATION............................. |
14 |
Raccordement du tuyau de vidange............................ |
15 |
Raccordement des tuyaux d’arrivée d’eau.................. |
16 |
Établissement de l’aplomb de la laveuse.................... |
17 |
Liste de vérification pour l’achèvement |
|
de l’installation............................................................... |
19 |
INSTALLATION NOTES |
NOTES SUR L’INSTALLATION |
Date of purchase:_________________________________ |
Date d’achat :____________________________________ |
Date of installation:_ _______________________________ |
Date d’installation :_ _______________________________ |
Installer:_________________________________________ |
Installateur :______________________________________ |
Model number:____________________________________ |
Numéro de modèle :________________________________ |
Serial number:____________________________________ |
Numéro de série :__________________________________ |
WASHER SAFETY
W10408696B |
W10409178B - SP |
INSTALLATION REQUIREMENTS
Tools and Parts
Gather required tools and parts before starting installation.
Tools needed:
|
|
|
|
|
|
|
|
|
Adjustable or open end |
|
Level |
||||||
wrenches 1⁄2" (13 mm) and |
|
|
|
|
|
|
||
9⁄16" (14 mm) |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
4" min |
|
|
|
|
|
|
|
|
(102 mm) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Wood block |
Ruler or measuring tape |
|
|
|
|
Pliers that open to 19⁄16" (39.5 mm)
Parts supplied:
NOTE: All parts supplied for installation are in the washer basket.
|
|
|
Beaded tie strap |
Drain hose |
|
|
|
|
|
|
|
Drain hose form and hose clamp
Optional tools:
Flashlight
Transport bolt hole plugs (Quantity will vary, depending on model.)
Bucket
Parts needed: (Not supplied with washer)
Inlet hoses (2) with washers (4)
Alternative Inlet Hoses:
(may be required for some installations, not supplied with washer)
n8212656RP 10 ft (3.0 m) Inlet hose, Black EPDM (2 pack)
n8212641RP 5 ft (1.5 m) Inlet hose, Black EPDM (2 pack)
n8212546RP 4 ft (1.2 m) Inlet hose, Black EPDM (2 pack)
n8212545RP 5 ft (1.5 m) Inlet hose, Red and Blue EPDM
(2 pack)
n8212487RP 5 ft (1.5 m) Nylon braided inlet hose (2 pack)
n8212638RP 6 ft (1.8 m) Nylon braided inlet hose, space
saving 90° elbow, hypro-blue steel couplings (2 pack)
n 8212637RP 6 ft (1.8 m) Inlet hose, Black EPDM, space saving 90° elbow, hypro-blue steel couplings (2 pack)
Available Accessories:
An optional matching pedestal is available for your washer. Please contact your retailer for ordering information, or see the Assistance or Service page on the back of your Use and Care Guide.
Alternative parts
(Not supplied with washer)
Your installation may require additional parts. To order, please refer to toll-free numbers on the back page of your Use and Care Guide.
If you have: |
You will need: |
Laundry tub or |
Sump pump system |
standpipe taller than |
(if not already available) |
96" (2.4 m) |
|
Overhead sewer |
Standard 20 gal. (76 L) 30" (762 mm) |
|
tall drain tub or utility sink and sump |
|
pump (available from local plumbing |
|
suppliers) |
1" (25 mm) standpipe |
2" (51 mm) diameter to 1" (25 mm) |
|
diameter Standpipe Adapter |
|
Part Number 3363920 |
|
Connect Kit Part Number 285835 |
Floor drain system |
Siphon Break Part Number 285834; |
|
additional Drain Hose, |
|
Part Number 8318155; and Connector |
|
Kit, Part Number 285835 |
Drain hose too short |
Extension Drain Hose |
|
Part Number 285863 |
Water faucets beyond |
2 longer water fill hoses; |
reach of fill hoses |
6 ft (1.8 m) Part Number 76314 |
|
10 ft (3.0 m) Part Number 350008 |
2
LOCATION REQUIREMENTS
Proper installation is your responsibility.
You will need:
nA water heater set to 120° F (49° C).
nA grounded electrical outlet located within 6 ft (1.8 m) of power cord on back of washer.
nHot and cold water faucets located within 4 ft (1.2 m) of hot and cold water fill valves on washer, and water pressure of 20-100 psi (137.9-689.6 kPa).
nA level floor with maximum slope of 1" (25 mm) under entire washer. Installing on carpet or surfaces with foam backing is not recommended.
nFloor must support washer’s total weight (with water and load) of 400 lbs (180 kgs).
IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32° F
(0° C). Water remaining in washer after use may cause damage in low temperatures. See “Washer Care” in Washer Use and Care Guide for winterizing information.
501/4" |
27" |
|
(686 mm) |
||
(1276 mm) |
||
|
36" (914 mm)
301/2"
(775 mm)
All dimensions show recommended spacing allowed, except for closet door ventilation openings which are the minimum required.
For each arrangement, consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings.
Space must be large enough to allow door to fully open. Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.
Recessed area or closet installation (stacked washer and dryer):
12" (305 mm)
|
3" |
|
|
(76 mm) |
48 in.2 |
|
|
|
|
|
(310 cm2) |
|
72" |
|
|
(1829 mm) |
|
|
|
24 in.2 |
1 |
|
(155 cm2) |
5 /4" |
3" |
|
(133 mm) |
|
|
(76 mm) |
|
|
|
|
1" 1" (25 mm)
(25 mm)
Custom under counter installation:
2" (50 mm)
36" min. (914 mm)
1" (25 mm)
(25 mm)
Recessed area or closet installation (washer only):
|
3" |
|
48" min. |
(76 mm) |
48 in.2 |
(1220 mm) |
|
|
|
(310 cm2) |
|
|
24 in.2 |
4" |
|
(155 cm2) |
|
3" |
|
(102 mm) |
|
|
|
(76 mm) |
|
|
|
|
|
1" |
1" |
|
(25 mm) |
|
|
(25 mm) |
|
|
|
Recessed or closet installation (washer on pedestal):
3824" min. (965610 mm)
4" (102 mm)
1" |
1" |
|
(25 mm) |
||
(25 mm) |
||
|
3
Custom cabinet installation: |
Wall standpipe drain system |
7" (178 mm)
9" (229 mm)
4" (102 mm)
1" |
1" |
|
(25 mm) |
||
(25 mm) |
||
|
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.
IMPORTANT: To avoid siphoning, only 41/2" (113 mm) of drain hose should be inside standpipe. Always secure drain hose with beaded tie strap.
Floor standpipe drain system
41/2"
(113 mm)
See requirements for floor standpipe drain system.
Laundry tub drain system
41/2" (113 mm) 30"
(762 mm)
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 30" (762 mm) above floor; install no higher than 96" (2.4 m) from bottom of washer.
Floor drain system
41/2" |
30" |
|
(113 mm) |
||
(762 mm) |
||
|
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm) diameter to 1" (25 mm) diameter Standpipe Adapter Kit is available (Part Number 3363920). Top of standpipe must be
at least 30" (762 mm) high; install no higher than 96" (2.4 m) from bottom of washer. If you have an overhead sewer and need to pump higher than 96 inches, a sump pump and associated hardware are needed. See “Alternative Parts”.
3028"
(76210 mm)
Floor drain system requires a Siphon Break Kit (Part Number 285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be purchased separately. See “Alternative Parts”. Minimum siphon break height: 28" (710 mm) from bottom of washer. (Additional hoses may be needed.)
4
ELECTRICAL REQUIREMENTS
INSTALLATION INSTRUCTIONS
nA 120 volt, 60 Hz., AC only, 15or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit breaker serving only this appliance be provided.
nThis washer is equipped with a power supply cord having a 3 prong grounding plug.
nTo minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.
nIf codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.
nDo not ground to a gas pipe.
nCheck with a qualified electrician if you are not sure the washer is properly grounded.
nDo not have a fuse in the neutral or ground circuit.
NOTE: To avoid floor damage, set washer onto cardboard before moving it.
1. Move washer |
48" |
(1.2 m) |
It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer.
Move washer to within 36" (914 mm) of its final location. It must be in a fully upright position.
2. Locate transport bolts
Locate all transport bolts on rear of washer (quantity may vary, depending on model).
5
3. Remove transport bolts from |
6. Place power cord over top |
washer |
|
Loosen bolts with a 13 mm (1/2") wrench.
Slide each bolt and spacer to center of hole. Pull bolts and plastic spacers from back of washer. Save transport bolts and spacers. Contact a qualified servicer if washer is to be transported.
4. Cover bolt holes with transport bolt hole plugs
Close bolt holes on cabinet back with transport bolt hole plugs included with washer parts.
5. Remove power cord
Pull power cord through opening in rear panel and close holes (2) with attached white plastic cap.
NOTE: If washer is transported at a later date, call a certified technician to properly set up washer for relocation, to avoid suspension and structural damage.
Gently place power cord over top of washer to allow free access to back of washer.
CONNECT DRAIN HOSE
7. Attach drain hose to drain port
Squeeze hose clamp tabs with pliers and slide over end of drain hose. Slide drain hose onto washer elbow connector and secure with clamp.
For a laundry tub or standpipe drain, go to step 8.
You may need additional parts with separate directions. See Floor drain system under “Alternative Parts”.
6