41055006bGB.fm Page 16 Thursday, July 27, 2006 9:41 AM
INSTRUCTIONS FOR USE
INSTALLATION ................................ |
17 |
SAFEGUARDING THE |
|
ENVIRONMENT............................................ |
20 |
IMPORTANT NOTES.................................... |
20 |
BEFORE USING THE OVEN......................... |
21 |
OVEN ACCESSORIES................................... |
22 |
CARE AND MAINTENANCE........................ |
23 |
TROUBLESHOOTING GUIDE ..................... |
27 |
AFTER SALES SERVICE................................ |
27 |
To make the most of your new oven, read the user's instructions carefully and keep them on hand for consultation in the future.
16
41055006bGB.fm Page 17 Thursday, July 27, 2006 9:41 AM
INSTALLATION
Recommendations
IMPORTANT: Disconnect the oven from the mains before carrying out any installation work or servicing.
_Installation must be carried out by a qualified technician in accordance with the manufacturer's instructions and in compliance with local regulations.
_Unpack the oven and make sure that the oven has not been damaged during transport and that the oven door closes properly. If you are not sure contact the dealer or the nearest service centre.
_After removing the oven from its packaging, leave it on the polystyrene base to prevent it from being damaged.
_ |
When installing the oven it is advisable to wear protective gloves. |
||
_ |
The oven is provided with two side handles |
|
(B) to facilitate installation (fig. 7). |
|
|||
Preparing the housing unit
_ Kitchen units in contact with the oven must be heat resistant (90 °C min).
_Cut the kitchen unit and worktop to fit before installing the oven. Carefully remove any shavings or sawdust that could prevent the oven from running properly.
_The dimensions of the housing units in which the oven can be installed are shown in figures 1, 2 and 3. The dimensions of the oven are shown in figure 4.
_To allow for proper ventilation, an opening should be left at the bottom of the housing unit. Pay attention to the dimensions. The bottom of the oven must not be accessible after installation.
_ During installation make sure that the sides of the oven do not touch the adjacent units.
2 |
3 |
1
4
17
41055006bGB.fm Page 18 Thursday, July 27, 2006 9:41 AM
_For ovens installed under the worktop, leave a minimum clearance of 5 mm between the upper edge of the oven and the lower edge of the worktop (fig. 5). For correct operation of the appliance, this clearance must always be unobstructed.
_If the kitchen unit is not securely fixed to the wall, it must be anchored with standard brackets (A) (fig. 6).
Electrical connection
Regulations require that the appliance be earthed.
_Connection to the mains must be carried out by a qualified technician in accordance with the manufacturer's instructions and in compliance with local regulations.
_The installer is responsible for connecting appliances correctly to the mains and for observing the safety regulations.
_ The oven power cable must be long enough to connect the built-in oven to the mains.
_Observance of safety directives requires that a multi-pole switch with a minimum contact gap of 3 mm be used for the installation.
_ Do not use multiple plug adapters or extension leads.
_ After the oven has been installed, the electrical components must be inaccessible.
6
5
18
41055006bGB.fm Page 19 Thursday, July 27, 2006 9:41 AM
Connecting the oven to the power supply
_Make sure that the voltage indicated on the rating plate is the same as the mains voltage. The rating plate is on the front edge of the oven (visible when the door is open).
_If the power cable is not present proceed as follows:
1.Remove the two fastening screws of the terminal box cover located on the bottom part of the oven's rear covering.
2.Remove the cover to gain access to the terminal box and insert the power cable (see table) through the opening located on the bottom of the oven.
Power supply cable table
N° of conductors |
Type of cable |
|
|
|
|
1N+ |
~ |
H05 RR-F 3 X 1.5 mm² |
|
|
|
3.Connect the cable to the terminal box, tighten the screws as far as they will go and secure it to the cable fastener.
4.Put the cover back on by inserting the two blades in the slots and fasten it with the two screws.
Securing the oven
_Lift up the oven getting hold of it by the handles (B) 
on the sides and insert it into the housing unit, being careful not to trap the power supply cable (fig. 8).
_ Center the oven in the housing unit before securing it.
_The oven comes with spacers 
already fitted to facilitate the anchoring of the oven to the housing unit with the screws provided (as shown in fig. 9).
7
8 |
9 |
19
Loading...