How it Works
WELLTECH
Loading...
FXO GATEWAY H.323 3806 - VERSION 117
User Manual
71 pgs3.81 Mb0

WELLTECH FXO GATEWAY H.323 3802 - VERSION 117, FXO GATEWAY H.323 3806 - VERSION 117, FXO GATEWAY H.323 3804 - VERSION 117, 3802 FXO User Manual

2
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
© Copyright 2003 Welltech Computer Co., Ltd.
All intellectual property rights in this publication are owned by Welltech Computer Co., Ltd. and are protected by Republic of China copyright laws, other applicable copyright laws and international treaty provisions. Welltech Computer Co., Ltd. retains all rights not expressly granted.
No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by Welltech Computer Co., Ltd.
No representation of warranties for fitness for any purpose other than what is specifically mentioned in this guide is made either by Welltech Computer Co., Ltd. or its agents.
Welltech Computer Co., Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. Welltech Computer Co., Ltd. may make improvements or changes in the product(s) and/or the program(s) described in this documentation at any time.
If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to locate a copy, please contact Welltech Computer Co., Ltd. and a copy will be provided to you.
Unless otherwise indicated, Welltech Computer Co., Ltd. registered trademarks are registered in the Republic of China and other territories.
For further information, contact Welltech or your local distributor or reseller.
Welltech Computer Co., Ltd. 13F-4, No.150, Jian-Yi Road, Chung-Ho City, Taipei, Taiwan 235, R.O.C. Tel: +886-2-82265699 Fax: +886-2-82265799 E-mail: sales@mail.welltech.com.tw http://www.welltech.com.tw
3
WellGate 3804 User Manual
Table of Contents
1. INTRODUCTION ....................................................................................................................................... 4
1.1 FEATURES AND SPECIFICATION................................................................................................................. 5
1.2 A
PPEARANCE ........................................................................................................................................... 7
3802: ........................................................................................................................................................ 7
3804: ........................................................................................................................................................ 8
3806: ........................................................................................................................................................ 9
2. SYSTEM OPERATING PROCEDURE ...................................................................................................11
2.1 SYSTEM REQUIREMENT ......................................................................................................................... 13
2.2 T
ELEPHONE LINE REQUIREMENT........................................................................................................... 14
2.3 IP E
NVIRONMENT SETTING.................................................................................................................... 14
2.4 H
YPER TERMINAL SETTING ................................................................................................................... 15
3. INITIALIZING WELLGATE FXO GATEWAY SETTING ................................................................. 18
3.1 GATEKEEPER MODE............................................................................................................................... 18
3.2 P
EER-TO-PEER MODE ............................................................................................................................ 22
3.3 B
EHIND IP-SHARING.............................................................................................................................. 23
4. DISCONNECT TONE CONFIGURATION ........................................................................................... 24
4.1 WHAT IS DISCONNECT TONE.................................................................................................................. 24
4.2 H
OW TO CONFIGURE DISCONNECT TONE ON WELLGATE FXO GATEWAY GATEWAY .............................. 25
4.3 A
DJUST TONE TABLE PARAMETERS MANUALLY .................................................................................... 26
4.4 A
DJUST INPUT TONE LEVEL .................................................................................................................. 26
5. COMMAND LISTS................................................................................................................................... 27
5.1 [HELP] COMMAND .................................................................................................................................. 27
5.2 [
QUIT] COMMAND .................................................................................................................................. 27
5.3 [
DEBUG] COMMAND............................................................................................................................... 28
5.4 [
REBOOT] COMMAND ............................................................................................................................. 28
5.5 [
FLASH] COMMAND................................................................................................................................ 29
5.6 [
COMMIT] COMMAND............................................................................................................................. 29
5.7 [
IFADDR] COMMAND .............................................................................................................................. 29
5.8 [
TIME] COMMAND .................................................................................................................................. 31
5.9 [
PING] COMMAND .................................................................................................................................. 31
5.10 [
GREETRD] COMMAND ......................................................................................................................... 32
5.11 [
PBOOK] COMMAND ............................................................................................................................. 34
5.12 [
PPPOE] ................................................................................................................................................ 36
5.13 [
SYSCONF] COMMAND.......................................................................................................................... 37
5.14 [
H323] COMMAND................................................................................................................................ 40
5.15 [
VOICE] COMMAND .............................................................................................................................. 43
5.16 [
TOS] COMMAND.................................................................................................................................. 45
5.17 [
TONE] COMMAND ............................................................................................................................... 45
5.18 [
SUPPORT] COMMAND .......................................................................................................................... 46
5.19 [
GROUP] COMMAND ............................................................................................................................. 47
5.20 [
BUREAU] COMMAND........................................................................................................................... 48
5.21 [
PREFIX] COMMAND............................................................................................................................. 50
5.22 [
ROM] COMMAND................................................................................................................................. 51
5.23 [
PASSWD] COMMAND ........................................................................................................................... 52
6. UPGRADE THE WELLGATE FXO GATEWAY .................................................................................. 54
TFTP/FTP SERVER ...................................................................................................................................... 54
D
OWNLOAD PROCEDURE............................................................................................................................. 54
7. APPENDIX: WEB CONFIGURATION.................................................................................................. 56
4
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
1. Introduction
The WellGate FXO gateway provides voice/fax service over IP network with H.323 v3 protocol. By connecting to your existing ADSL or cable modem service, which allows the use of a single, network for voice and fax services with consequent saving in network infrastructure and greatly reduced telephone charges. Ideal solution for providing low cost communications between headquarters and branch offices in the world, as well as for SOHO and office telephony applications.
WellGate FXO GateWay provides analog lines to connect local PSTN/PTT interface (FXO), and converts voice/fax signal onto IP network. The management feature is via RS-232C COM port and TELNET.
5
WellGate 3804 User Manual
1.1 Features and specification
General Features
- ITU-T H.323 v3 compliance
- Automatically Gatekeeper Discovery
- Peer-to-Peer mode (non-Gatekeeper)
- Support auto-attendant (2nddial Tone / Voice greeting)
- Dimensions : 221mm(W)*42mm(H)*217mm(L)
- Line hunting
- 2(3802)/4(3804)/6(3806) RJ-11 FXO ports
- E.164 (Telephone Number Plan)
- DTMF dialing
- DTMF detection/generation
- TFTP software upgrade
- Remote configuration/reset via Telnet
- LED indication for system status
- LAN interface : One RJ-45 connector of 10Base-T
- Microsoft Netmeeting v3.0 compatible
- Support static IP and DHCP
- QoS by ToS (Type Of Service)
- SNTP (Simple Network Time Protocol)
- Security: Password setting
Audio feature
- Codec -- G.711 a/μ law, G.723.1 (6.3K/bps), G.729A (Optional)
- VAD (Voice Activity Detection), CNG (Comfort Noise Generate)
- G.168/165-compliant adaptive echo cancellation
- Dynamic Jitter Buffer
- Bad Frame Interpolation
- Call Transfer (H.450.2)
- Call Forward (H.450.3)
- Call Hold (H.450.4)
- Gain Settings
- Provide Call Progress Tone: Dial tone, busy tone, call-holding tone and ring-back tone
Management Features:
Two easy ways for system configuration
6
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
- Console port: RS-232C port
- TELNET
- HTTP Brower (e.g. Internet Explorer)
7
WellGate 3804 User Manual
1.2 Appearance
3802:
Front panel: The LED light provides system message of WellGate3802.
Power : Light on means WellGate3802 is power on. L1-L2 : Light on means the line is in use. Link : Light on means WellGate3802 is connected to the network
correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate3802 is in operation
mode.
Status : 1. Light on means WellGate3802 successfully registered to
Gatekeeper when it is set as Gatekeeper Mode.
2. LED flash means WellGate3802 is not registered to Gatekeeper when it is set as Gatekeeper Mode.
3. Or when WellGate3802 is in downloading mode, LED should
be flash as well.
4. Light off means WellGate3802 is in Peer-to-Peer Mode.
Back panel:
8
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
3804:
Front panel: The LED light provides system message of WellGate FXO GateWay.
Power : Light on means WellGate FXO GateWay is power on. L1-L4 : Light on means the line is in use. Link : Light on means WellGate FXO GateWay is connected to the
network correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate FXO GateWay is
in operation mode.
Status : 1. Light on means WellGate FXO GateWay successfully
registered to Gatekeeper when it is set as Gatekeeper Mode.
2. LED flash means WellGate FXO GateWay is not registered to Gatekeeper when it is set as Gatekeeper Mode.
3. Or when WellGate FXO GateWay is in downloading mode,
LED should be flash as well.
4. Light off means WellGate FXO GateWay is in Peer-to-Peer
Mode.
Back panel:
9
WellGate 3804 User Manual
3806:
Front panel: The LED light provides system message of WellGate3806.
Power : Light on means WellGate3806 is power on. L1-L6 : Light on means the line is in use. Link : Light on means WellGate3806 is connected to the network
correctly. Act : LED should be light on and in flash display when data is transmitting. Ready : 1. Light on and in slow flash means WellGate3806 is in operation
mode.
Status : 1. Light on means WellGate3806 successfully registered to
Gatekeeper when it is set as Gatekeeper Mode.
2. LED flash means WellGate3806 is not registered to Gatekeeper when it is set as Gatekeeper Mode.
3. Or when WellGate3806 is in downloading mode, LED should
be flash as well.
4. Light off means WellGate3806 is in Peer-to-Peer Mode.
Back panel:
10
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
10 Base-T: RJ-45 Modular Jack Female connector with 10 Mbps Ethernet.
PIN 1, 2: Transmit
PIN 3, 6: Receive
COM: RS232 console port (9-pin Male connector, as the same as the computer).
Male connector (as the same as the PC)
11
WellGate 3804 User Manual
9 PIN D-SUB MALE at the WellGate FXO GateWay
Pin Name Dir Description
2 RXD
Receive Data
3 TXD
Transmit Data
5 GND
─
System Ground
L1 ~ L4: RJ-11 (PSTN or Extension Line of PBX)
On / Off: Power switch on/off.
100 - 240 VAC: AC Power supply.
2. System Operating Procedure
12
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
2.1 System Requirement
2.2 Telephone Line Requirement
2.3 IP Environment Setting
START
END
2.4 Hyper Terminal Setting
13
WellGate 3804 User Manual
2.1 System Requirement
1. One PC (a) Pentium 100 or above, 64 MB DRAM, Windows 98 or above. (b) Network card (RJ-45) & COM port
2. One standard RS-232 straight cable with
two female connectors
depended on the different model.
3. PSTN lines / PBX extension lines (up to 4 lines).
4. Software tools (a) Hyper terminal, telnet (Windows OS included)
(b) Gatekeeper (optional)
14
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
2.2 Telephone Line Requirement
Two kinds of analog lines can be connected to RJ-11 of WellGate FXO GateWay.
1. PSTN (Public Switched Telephone Network, POTS) or
2. PABX (Private Automatic Branch Exchange) / PBX (Private Branch Exchange) extension line.
PSTN
1. It is necessary to provide PSTN/POTS telephone lines in order to plug into RJ-11 of WellGate FXO GateWay.
2. The maximum telephone lines are up to 2(3802)/4(3804)/6(3806).
PABX / PBX
1. 2(3802)/4(3804)/6(3806) PSTN lines can be replaced to the 2(3802)/4(3804)/6(3806) extension lines of PBX.
Note: Since the Line function feature starts from L1, please plug the
telephone lines from L1.
2.3 IP Environment Setting
User must prepare a valid IP address to be complied IP Network policy in order for WellGate FXO GateWay operating correctly.
For example, if your company’s IP address is 192.168.4.111, subnet mask is
255.255.0.0, default gateway is 192.168.1.254, you should prepare one IP for
WellGate FXO GateWay, such as IP address is 192.168.4.99, and the same subnet mask and default gateway.
15
WellGate 3804 User Manual
2.4 Hyper Terminal Setting
1. Execute the Hyper Terminal program, then the following windows pop-up on the screen. (START – Program files – Accessories – Communication – Hyper Terminal)
2. Define a name such as ‘3804 Gateway’ for this new connection.
16
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
3. After pressing OK button, the next window popping up is necessary to connect choose COM Port.
Note:
Some connection failed is derived the PC COM Port. If user cannot open
the com port, for example com 1, please try another com port, ex.
com port
2.
4. Configure the COM Port Properties as following:
(1) Bits per second : 9600 (2) Flow control : None
17
WellGate 3804 User Manual
Press ‘OK’ button, and start to configure WellGate FXO GateWay.
18
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
3. Initializing WellGate FXO GateWay Setting
3.1 Gatekeeper Mode
(a) Configure WellGate FXO GateWay Password
(b) Configure WellGate FXO GateWay IP Address
(c) Gatekeeper Mode Settings
START
END
(d) Save WellGate FXO GateWay Configuration
& Reboot WellGate FXO GateWay
19
WellGate 3804 User Manual
(a) Configure WellGate FXO GateWay Password
It is important for the first time user to follow the operation procedure.
1. Power on the WellGate FXO GateWay and the sentence “Please wait while system is initializing…………S” is displayed.
---------------------------------------------------------------------------------------------
Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
Please wait while system is initializing .......... S
2. Wait around 40 seconds, the login name and password are requested.
---------------------------------------------------------------------------------------------
Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
AC4804[0] is OK
AC4804[1] is OK
AC4804[2] is OK
Successful
Initialize OSS libraries...OK!
open stack successful
cmInitialize succeed!
GK mode selected.
20
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
login:
3. Login: when WellGate FXO GateWay is used for the first time, “root” is default login name without a password.
4. Password setting: type “passwd –set root ****” to define a password for “root” account. “****”, in above description, stands for contents of the password. An example, to set root’s password as good, is demonstrated as following:
---------------------------------------------------------------------------------------------
usr/config$ passwd -set root good
Setting
login: root
Password: good
OK
(b) Configure WellGate FXO GateWay IP Address
Use “ifaddr” command to set up WellGate FXO GateWay’s IP address and related network information. An example is demonstrated below:
---------------------------------------------------------------------------------------------------
usr/config$ ifaddr – ip 10.1.1.1 – mask 255.2555.255.0 – gate 10.1.1.254
Note: this is to assign WellGate FXO GateWay an IP address of “10.1.1.1”, subnet mask “255.255.255.0”, and default IP gateway “10.1.1.254”.
(c) Gatekeeper Mode Settings
To assign a gatekeeper address for WellGate FXO GateWay, and define its own registered ID and phone number. For detail, please refer to Chapter 5.14 [h323] command. Several important H323 parameters is listed below when setting gatekeeper mode: “–gk”, ”–e164”, and ”–alias”.
21
WellGate 3804 User Manual
An example is demonstrated below:
---------------------------------------------------------------------------------------------------------
usr/config$ h323 – gk 10.2.2.2 – e164 – alias fxo
Note: This is to set gatekeeper IP address as “10.2.2.2”, e.164 number as “1”, and alias name (h323ID) as “
fxo”.
(d) Save WellGate FXO GateWay Configuration & Reboot WellGate FXO
GateWay
1. Confirming the values, type commit and press enter to save all the changes you have done.
2. Type reboot and press enter to reboot the WellGate FXO GateWay.
3. Wait for WellGate FXO GateWay initializing in gatekeeper mode.
22
WellGate FXO GateWay User Manual
S/W version:x4fxo.117
3.2 Peer-to-Peer Mode
Peer-to-Peer Mode allows users to call other VoIP devices without using a gatekeeper. When in Peer-To-Peer mode, WellGate FXO GateWay will send SETUP message directly to the destination IP address once the dial is finished. Users have 2 methods of dial. One is IP dialing, and the other is Phonebook dial, which we will describe later. When using IP address as destination phone number, press “*” as “.” in IP address expression, and press “#” when dial is finished. When using Phonebook, users can dial predefined phone number, and press “#” (optional, to accelerate the dial) as end of dial.
To configure Peer-To-Peer Mode in WellGate FXO GateWay, follow the steps below:
1. Set Peer-To-Peer Mode, using “h323” command
-------------------------------------------------------------------------------------------------
usr/config$ h323 – mode 1
Note: mode 1 is for Peer-To-Peer (non-gk) mode, while mode 0 is for GK
mode.
2. Configure Phonebook, using “pbook” command.
Users can refer to chapter 5.11 [pbook] command for more information.
-------------------------------------------------------------------------------------------------
usr/config$ pbook – add name TEST1 ip 10.1.1.1 e164 10
Note: the command is to add a record onto Phonebook. After the command
completed, you can type “pbook –print” to see if the input record is correct.
When adding a record to Phonebook, users do not have to reboot the
machine, and the record will be effective immediately.
Loading...
+ 49 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use