Transition Networks SIBTF10XX-1XX-MR, SIBTF10XX-1XX-MS User Manual

User’s Guide

SIBTF10xx-1xx-MR & SIBTF10xx-1xx-MS Substation-Rated Industrial Ethernet Switch

• 10/100Base-TX to 100Base-FX

• Single or Redundant Wide Input Power Supply

The SIBTF10xx-1xx-Mx Ethernet industrial switches allow connecting 10Base-T Ethernet/100Base-TX fast Ethernet twisted-pair copper network devices to network devices on a 100Base-FX fast Ethernet fiber

140-MR

and one fiber port. The SIBTF10xx-140-MR model includes redundant power-supply terminal blocks that can handle 48–170VDC or 90–125VAC, 50/60Hz input power. The SIBTF10xx-140-MS model, not shown, has a single power-supply terminal block (TB).

The SIBTF10xx-130-MR has three RJ-45 copper ports and two fiber ports. The SIBTF10xx-130-MR model includes redundant power-supply terminal blocks that can handle 48–170VDC or 90–125VAC, 50/60Hz input power. The SIBTF10xx-130-MS model, not shown, has a single power-supply terminal block (TB).

network.

The SIBTF10xx-140-MR has four RJ-45 copper ports

110-MR

130-MR

The SIBTF10xx-110-MR has one RJ-45 copper port and one fiber port. The SIBTF10xx-110-MR model includes redundant power-supply terminal blocks that can handle 48–170VDC or 90–125VAC, 50/60Hz input power. The SIBTF10xx-110-MS model, not shown, has a single power-supply terminal block (TB).

Available Models . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . .4

Operation . . . . . . . . . . . . . . . . . .15

Cable Specifications . . . . . . . . . .20

Technical Specifications . . . . . . .22

Troubleshooting . . . . . . . . . . . . .24

Compliance Information . . . . . . .27

SIBTF10xx-1xx-Mx

Available Models

Available SIBTF10xx-140-MR and MS models*

Part Number (4) Copper - 10Base-T/

100Base-TX ports

SIBTF1011-140-Mx

SIBTF1013-140-Mx

SIBTF1014-140-Mx

SIBTF1015-140-Mx

SIBTF1016-140-Mx

SIBTF1017-140-Mx

RJ-45 100 m (328 ft)

*MR = Redundant power-supply terminal blocks, MS = Single power-supply terminal block.

Note: The cable distances listed are maximum distances typically. The actual distance

is dependent upon the physical characteristics of the network.

Available SIBTF10xx-130-MR and MS models*

Part Number (3) Copper - 10Base-T/

SIBTF1011-130-Mx

SIBTF1013-130-Mx

SIBTF1014-130-Mx

SIBTF1015-130-Mx

SIBTF1016-130-Mx

SIBTF1017-130-Mx

100Base-TX Ports

RJ-45 100 m (328 ft)

(1) Duplex Fiber-Optic - 100Base-FX port

ST, 1300 nm multimode, duplex 2 km (1.2 miles)

SC, 1300 nm multimode, duplex 2 km (1.2 miles)

SC, 1310 nm single mode, duplex 20 km (12.4 miles)

SC, 1310 nm single mode, duplex 40 km (24.8 miles)

SC, 1310 nm single mode, duplex 60 km (37.2 miles)

SC, 1550 nm single mode, duplex 80 km (49.7 miles)

(2) Duplex Fiber-Optic - 100Base-FX Ports

ST, 1300 nm multimode, duplex 2 km (1.2 miles)

SC, 1300 nm multimode, duplex 2 km (1.2 miles)

SC, 1310 nm single mode, duplex 20 km (12.4 miles)

SC, 1310 nm single mode, duplex 40 km (24.8 miles)

SC, 1310 nm single mode, duplex 60 km (37.2 miles)

SC, 1550 nm single mode, duplex 80 km (49.7 miles)

Available Models -- continued

Available SIBTF10xx-110-MR and MS models*

Part Number (1) Copper - 10Base-T/

100Base-TX Port

SIBTF1011-110-Mx

SIBTF1013-110-Mx

SIBTF1014-110-Mx

SIBTF1015-110-Mx

SIBTF1016-110-Mx

SIBTF1017-110-Mx

RJ-45 100 m (328 ft)

*MR = Redundant power-supply terminal blocks, MS = Single power-supply terminal block..

Note: The cable distances listed are maximum distances typically. The actual distance

is dependent upon the physical characteristics of the network.

(1) Duplex Fiber-Optic - 100Base-FX Port

ST, 1300 nm multimode, duplex 2 km (1.2 miles)

SC, 1300 nm multimode, duplex 2 km (1.2 miles)

SC, 1310 nm single mode, duplex 20 km (12.4 miles)

SC, 1310 nm single mode, duplex 40 km (24.8 miles)

SC, 1310 nm single mode, duplex 60 km (37.2 miles)

SC, 1550 nm single mode, duplex 80 km (49.7 miles)

*MR = Redundant power-supply terminal blocks, MS = Single power-supply terminal block.

Note: The cable distances listed are maximum distances typically. The actual distance

is dependent upon the physical characteristics of the network.

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.

SIBTF10xx-1xx-Mx

Installation

Features

• The SIBTF10xx-140-MR industrial switch includes four (4) RJ-45, twisted-pair copper ports and one (1) 100 Mb fiber optic port.

• The Auto-Negotiation feature on port “1” can be turned OFF and forced to a selected speed (100 Mb/s or 10 Mb/s) also duplex mode (full or half).

• All SIBTF models include a primary input terminal block (TB) for 48–170VDC or 90–125VAC power, a 2.5A, 250V fuse, an LED power indicator, and a red-fault LED. The red-fault LED “ON state” indicates the microcontroller did not initialize correctly.

• The “MR” models include an auxiliary power-supply terminal block—not available on “MS” models.

See Figure 1.

Installation -- continued

Features -- continued

• The SIBTF10xx-130-MS industrial switch includes three (3) RJ-45, twisted-pair copper ports and one (2) 100 Mb fiber optic port.

• The Auto-Negotiation feature on port “1” can be turned OFF and forced to a selected speed (100 Mb/s or 10 Mb/s) and duplex mode (full or half).

• All SIBTF models include a primary input terminal block (TB) for 48–170VDC or 90–125VAC input power power, a 2.5A, 250V fuse, an LED power indicator, and a red-fault LED. The red-fault LED “ON state” indicates the microcontroller did not initialize correctly.

• The “MR” models include an auxiliary power-supply terminal block—not available on “MS” models.

See Figure 2.

Figure 1: SIBTF10xx-140-MR Front Panel

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Figure 2: SIBTF10xx-130-MR Front Panel

techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.

SIBTF10xx-1xx-Mx

Installation -- continued

Features -- continued

• The SIBTF10xx-110-MS industrial switch includes one (1) RJ-45, twisted-pair copper port and one (1) 100 Mb fiber optic port.

• The Auto-Negotiation feature on port “1” can be turned OFF and forced to a selected speed (100 Mb/s or 10 Mb/s) and duplex mode (full or half).

• All SIBTF models include a primary input terminal block (TB) for 48–170VDC or 90–125VAC power, a 2.5A, 250V fuse, an LED power indicator, and a fault LED. The red-fault LED “ON state” indicates the microcontroller did not initialize correctly.

• The “MR” models include an auxiliary power-supply terminal block—not available on “MS” models.

See Figure 3.

Installation -- continued

Enclosure top view (configuration switches)

The SIBTF10xx-1xx-Mx has eight (8) configuration (DIP) switches located under the switch cover on top of the enclosure. See Figure 4.

Switch Position 1

1-Config Switches

Figure 4: Enclosure Top View Configuration Switches

Figure 3: SIBTF10xx-110-MR Front Panel

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Setting configuration switches

To set the DIP switches:

1. Using a small, phillips-head screwdriver, loosen (do not remove) the two screws that secure the cover to the switch.

2. Swing the switch cover counter-clockwise to expose the DIP switches.

3. Use a small, flathead screwdriver to set the recessed switches as required by the network application.*

4. Slide the switch cover back over the DIP switches and then secure it by tightening both screws.

*Note: Switches 1, 2, and 3 apply only to twisted-pair “copper port #1.”

techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.

SIBTF10xx-1xx-Mx

Installation -- continued

DIP switch settings

1. Port 1 copper Auto-Negotiation:

UP (Enabled) - Advertises switch speed and mode capabilities to the network:

• 100Mb/s full-duplex • 100Mb/s half-duplex,

• 10Mb/s full-duplex • 10Mb/s half-duplex.

DOWN (Disabled) - Does not advertise switch speed and mode capabilities to the network. With AutoNegotiate disabled switches 2 and 3 are used to set the twisted-pair speed and mode.

2. Port 1 copper speed:

UP (100Base-TX) - Sets the twisted-pair speed to 100Base-TX.

DOWN (10Base-T) - Sets the twisted-pair speed to 10Base-T.

3. Port 1 copper duplex:

UP (Full-Duplex) - The twisted-pair cable distances are constrained by the cable requirements.

DOWN (Half-Duplex): - The twisted-pair cable distances are constrained by the 512-Bit Rule.

4. Fiber port FX 1 duplex:

UP (Full-Duplex) - The cable distances for the fiber port are constrained by the cable requirements.

DOWN (Half-Duplex) - The cable distances for the fiber port are constrained by the 512-Bit Rule.

Auto-Negotiation E nabled

Auto-Ne

otiation Dis abled

100Bas e-TX

10Bas e-TX

Full Duplex

Half Duplex

Full Duplex (fiber)

Half Duplex (fiber)

Installation -- continued

6. Link Pass-Through (model 110 only): UP (Enable) - When Link Pass-Through is enabled, a fault on one side of the switch stops the signal and data transmission on the other side. See the detailed explanation of Link Pass-Through on page 18.

DOWN (Disable) - When Link Pass-Through is disabled, a fault on one side of the switch does not stop the signal and data transmission on the other side.

7. Fiber redundancy (model 130 only): UP (Disable) - When fiber redundancy is disabled, the two fiber ports (1 and 2) act as normal bridging ports.

DOWN (Enable) - When fiber redundancy is enabled, the two fiber ports (1 and 2) are configured as forwarding or disabled. At any given time one port will be disabled and one port will be forwarding.

8. AutoCross: UP (Enable) - The switch will connect to a straightthrough or a crossover twisted-pair copper cable automatically.

DOWN (Disable) - In the down position the straightthrough or crossover twisted-pair copper cable must be installed according to the site requirements.

Link Pa ss- Through E nabled

Link Pa ss- Through Disabled

Redund ant Fiber E nabled

Redund ant Fiber Disabled

AutoCross E nabled

AutoCross Disab led

5. Fiber port FX 2 duplex (model 130 only):

UP (Full-Duplex) - The cable distances for the fiber port are constrained by the cable requirements.

DOWN (Half-Duplex) - The cable distances for the fiber port are constrained by the 512-Bit Rule.

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Full Duplex (fiber)

Half Duplex (fiber)

techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.

+ 10 hidden pages