TP-Link TL-SG105, TL-SG105S, TL-SG108, TL-SG108S, TL-SG116 Installation Guide

Installation Guide

5/8/16-Port Gigabit Desktop Switch

Note:

For simplicity, we will take TL-SG108 for example throughout this Guide.

LED Explanation

Power

On: Power on

O: Power o

Link/Act (For TL-SG105/TL-SG105S/TL-SG108/TL-SG108S)

Link/Act (Green)

Running at 10/100/1000 Mbps

On:

O:

No device is linked to the corresponding port

Flashing: Transmitting/receiving data

Link/Act (For TL-SG116)

1000M (Green) On: Running at 1000 Mbps Flashing: Transmitting/receiving data

10/100M (Yellow) On: Running at 10/100 Mbps Flashing: Transmitting/receiving data

Connection

Internet

Power Adapter

Router

LAN PortWAN Port

TL-SG108

Link/Act

Ethernet Ports (1-8)

Specications

General Specications

Standard

Protocol

Data Transfer Rate

Network Media (Cable)

Interface

LED Indicators

Advanced Features

Transfer Method

MAC Address Learning

Frame Forward Rate

Wall Mountable

Distance Between Mounting Holes

IEEE802.3, IEEE802.3i, IEEE802.3u, IEEE802.3ab,

IEEE802.3x, IEEE802.1p

CSMA/CD

Ethernet:

10 Mbps (Half Duplex), 20 Mbps (Full Duplex)

Fast Ethernet:

100 Mbps (Half Duplex), 200 Mbps (Full Duplex)

Gigabit Ethernet:

2000 Mbps (Full Duplex)

10Base-T:

UTP category 3, 4, 5 cable (maximum 100 m)

EIA/TIA-568 100

100Base-TX:

UTP category 5, 5e cable (maximum 100 m)

EIA/TIA-568 100

1000Base-T:

UTP category 5e cable (maximum 100 m)

EIA/TIA-568 100 Ω STP (maximum 100 m)

5/8/16 10/100/1000 Mbps Auto-Negotiation

RJ45 Ports

Power, Link/Act LED

IGMP Snooping, QoS (802.1p/DSCP Priority)

Store-and-Forward

Automatically learning, automatically aging

10Base-T: 14881pps/Port 100Base-TX: 148810pps/Port 1000Base-T: 1488095pps/Port

Ye s

TL-SG105/TL-SG105S: 52 mm TL-SG108/TL-SG108S: 110 mm TL-SG116: 200 mm

STP (maximum 100 m)

Frequently Asked Questions (FAQ)

Q1. The Power LED is not lit.

The Power LED should be lit when the power system is working normally. If the Power LED is not lit, check as follows:

A1:

Make sure the power adapter is connected to the switch with power source properly.

: Make sure the voltage of the power supply meets the requirements

of the input voltage of the switch.

A3:

Make sure the power source is ON.

Q2. The Link/Act LED is not lit when a device is connected to the corresponding port.

It is recommended that you check the following items:

A1:

Make sure that the cable connectors are rmly plugged into the

switch and the device.

A2:

Make sure the connected device is turned on and works normally.

A3:

The cable must be less than 100 meters long (328 feet).

Environmental and Physical Specications

Operating Temperature

Storage Temperature

Operating Humidity

Storage Humidity

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us. Do not use damaged charger or USB cable to charge the device.

Do not use any other chargers than those recommended. Adapter shall be installed near the equipment and shall be easily accessible. The plug on the power supply cord is used as the disconnect device, the

socket-outlet shall be easily accessible. Use only power supplies which are provided by manufacturer and in the origin packing of this product. If you have any questions, please don’t hesitate to contact us.

0 ˚C to 40 ˚C (32 ˚F to 104 ˚F)

-40 ˚C to 70 ˚C (-40 ˚F to 158 ˚F)

10% to 90%RH non-condensing

5% to 90%RH non-condensing

To ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link Community.

For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.

If you have any suggestions or needs on the product guides, welcome to email techwriter@tp-link.com.cn.

EU declaration of conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.