AV6**D Digital
Series
RV6**D Digital
Series
English
Contents |
|
INSTALLING YOUR TV |
|
Safety Precautions .................................................. |
4 |
Installation and important information .................... |
5 |
The remote control ................................................. |
6 |
Inserting batteries and effective range of the |
|
remote .......................................................... |
6 |
CONNECTING YOUR TV |
|
Connecting external equipment .............................. |
7 |
Connecting an HDMI™ or DVI device to the HDMI |
|
input ................................................................... |
8 |
To connect an HDMI device .............................. |
8 |
To connect a DVI device ................................... |
8 |
Connecting a computer .......................................... |
9 |
To connect a PC to the RGB/PC terminal .......... |
9 |
To connect a PC to the HDMI terminal .............. |
9 |
Controls and input connections ............................. |
10 |
Switching on .................................................. |
10 |
Using the remote control ............................... |
10 |
Using the controls and connections ................ |
10 |
SETTING UP YOUR TV |
|
Startup Application ............................................... |
11 |
Quick Setup ................................................... |
11 |
Ant/Cable In (if available) .............................. |
12 |
Auto Tuning ................................................... |
13 |
ATV Manual Tuning .............................................. |
13 |
Tuning ........................................................... |
13 |
Skip ............................................................... |
15 |
Sorting positions ............................................ |
15 |
DTV Manual Tuning .............................................. |
16 |
Manual Tuning .............................................. |
16 |
Manual Tuning for DVB-C .............................. |
16 |
DTV Settings ......................................................... |
16 |
Channels ....................................................... |
16 |
Auto Channel Update .................................... |
17 |
DVB Character Set ......................................... |
17 |
Analogue switch-off ..................................... |
17 |
Location setting ............................................. |
17 |
CONTROLS AND FEATURES |
|
General controls ................................................... |
18 |
Selecting positions ......................................... |
18 |
The Time Display – analogue only ................ |
18 |
Stereo and Bilingual transmissions ................. |
18 |
Quick Menu ................................................... |
18 |
Sound controls ..................................................... |
19 |
Volume controls and mute sound ................... |
19 |
Dual ............................................................. |
19 |
Bass, Treble and Balance ............................... |
19 |
Advanced Sound Settings .............................. |
19 |
Stable Sound® ............................................... |
19 |
Dynamic Range Control ................................. |
19 |
Audio Level Offset ......................................... |
20 |
Headphone Settings ...................................... |
20 |
Audio description .......................................... |
20 |
Widescreen viewing ............................................. |
21 |
Picture controls .................................................... |
23 |
Picture Position .............................................. |
23 |
Picture Mode ................................................. |
23 |
Picture preferences ........................................ |
23 |
Reset ............................................................. |
24 |
3D Colour Management ................................ |
24 |
Base Colour Adjustment ................................ |
24 |
Colour Temperature ...................................... |
24 |
Auto Brightness Senser Settings ..................... |
25 |
Active Backlight Control ................................. |
25 |
Black/White Level .......................................... |
25 |
Static Gamma ............................................... |
25 |
MPEG NR – Noise Reduction .......................... |
25 |
DNR – Digital Noise Reduction ....................... |
25 |
Resolution+ .................................................. |
26 |
Cinema Mode ............................................... |
26 |
Expert Mode .................................................. |
26 |
Resetting the advanced picture settings .......... |
26 |
Control Visualization ..................................... |
27 |
Automatic Format (Widescreen) ..................... |
27 |
4:3 Stretch .................................................... |
27 |
Blue Screen ................................................... |
27 |
Side panel adjustment ................................... |
27 |
Picture still ..................................................... |
27 |
Enjoying Photo through USB port .......................... |
28 |
To open Photo Viewer ................................... |
28 |
Viewing photo files ........................................ |
29 |
Other features ..................................................... |
30 |
Panel lock ..................................................... |
30 |
TOSHIBA Illumination .................................... |
30 |
The timers ............................................................ |
30 |
Programme Timers – digital only .................. |
30 |
On Timer ...................................................... |
31 |
Sleep Timer ................................................... |
31 |
Digital on-screen information and |
|
Programme Guide ............................................. |
32 |
Information ................................................... |
32 |
Guide ........................................................... |
33 |
Genre selection/searching ............................. |
33 |
2
English
Digital settings – parental control ........................ |
34 |
Setting the PIN .............................................. |
34 |
Parental Setup ............................................... |
34 |
Digital settings – Channel Options ....................... |
35 |
Selecting favourite channels ........................... |
35 |
Favourite Channel Lists .................................. |
35 |
Skip channels ................................................ |
35 |
Locking channels ........................................... |
35 |
Digital settings – other settings ............................. |
36 |
Subtitles ........................................................ |
36 |
Audio languages ........................................... |
36 |
Common Interface ......................................... |
36 |
Software Upgrade ................................................ |
37 |
Auto Upgrade ................................................ |
37 |
Searching for New Software ........................... |
37 |
System Information and Reset TV .......................... |
37 |
System Information ........................................ |
37 |
Reset TV ........................................................ |
37 |
PC Settings ........................................................... |
38 |
Horizontal and Vertical Position ..................... |
38 |
Clock Phase ................................................... |
38 |
Sampling Clock ............................................. |
38 |
Reset ............................................................. |
38 |
Input selection and AV connections ....................... |
39 |
Input selection ............................................... |
39 |
External input skip ......................................... |
39 |
INPUT signal selection ................................... |
39 |
PC Audio ....................................................... |
39 |
HDMI 1 Audio ............................................... |
40 |
HDMI Settings ............................................... |
40 |
Digital Audio Output ...................................... |
40 |
TEXT SERVICES |
|
Text services ......................................................... |
41 |
Selecting modes ............................................ |
41 |
Text information ............................................ |
41 |
Navigating pages using Auto ......................... |
41 |
Navigating pages using LIST .......................... |
41 |
Control buttons .............................................. |
42 |
PROBLEM SOLVING |
|
Questions and Answers ...................................... |
43 |
INFORMATION |
|
Notes ................................................................... |
46 |
Information .......................................................... |
48 |
Specifications and accessories ............................... |
50 |
3
English
INSTALLING YOUR TV
Safety Precautions
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken to obtain the best results and for safety to be assured. Please read the points below for your own safety. They are of a general nature, intended to help with all electronic consumer products and some points may not apply to the goods you have just purchased.
Air Circulation
DO NOT REMOVE ANY FIXED COVERS AS THIS WILL EXPOSE DANGEROUS AND 'LIVE' PARTS.
THE MAINS PLUG IS USED AS A DISCONNECTING DEVICE AND THEREFORE SHOULD BE READILY OPERABLE.
Do not
DO NOT obstruct the ventilation openings of the equipment with items such as newspapers, tablecloths, curtains, etc. Overheating will cause damage and shorten the life of the equipment.
Leave more than 10cm clearance around the television to allow adequate ventilation. This will prevent overheating and possible damage to the television. Dusty places should also be avoided.
Heat Damage
Damage may occur if the television is left in direct sunlight or near a heater. Avoid places subject to extremely high temperatures or humidity. Place in a location where the temperature remains between 5°C (41°F) min. and 35°C (94°F) max.
Mains Supply
The mains supply required for this equipment is 220240v AC 50/60Hz. Never connect to a DC supply or any other power source. DO ensure that the television is not standing on the mains lead. Use only the supplied lead.
DO NOT cut off the mains plug from this equipment, this incorporates a special Radio Interference Filter, the removal of which will impair its performance.
IF IN DOUBT PLEASE CONSULT A COMPETENT ELECTRICIAN.
Do
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and inter-connections between pieces of equipment) are properly made and in accordance with the manufacturers’ instructions. Switch off and withdraw the mains plug before making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
DO NOT allow electrical equipment to be exposed to dripping or splashing or objects filled with liquids, such as vases, to be placed on the equipment.
DO NOT place hot objects or naked flame sources, such as lighted candles or nightlights on, or close to equipment. High temperatures can melt plastic and lead to fires.
DO NOT use makeshift stands and NEVER fix legs with wood screws. To ensure complete safety, always fit the manufacturers’ approved stand, bracket or legs with the fixings provided according to the instructions.
DO NOT leave equipment switched on when it is unattended, unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off by withdrawing the plug, make sure your family know how to do this. Special arrangements may need to be made for people with disabilities.
DO NOT continue to operate the equipment if you are in any doubt about it working normally, or it is damaged in any way – switch off, withdraw the mains plug and consult your dealer.
WARNING – excessive sound pressure from earphones or headphones can cause hearing loss.
ABOVE ALL – NEVER let anyone, especially children, push or hit the screen, push anything into holes, slots or any other openings in the case.
NEVER guess or take chances with electrical equipment of any kind – it is better to be safe than sorry.
4
INSTALLING YOUR TV
Installation and important information
Where to install
Locate the television away from direct sunlight and strong lights, soft, indirect lighting is recommended for comfortable viewing. Use curtains or blinds to prevent direct sunlight falling on the screen.
Place the TV on a stable, level surface that can support the weight of the TV. As an additional safety measure you can secure the TV to the level surface or a wall, as shown in the illustration, using a sturdy strap.
The LCD display panels are manufactured using an extremely high level of precision technology, however sometimes some parts of the screen may be missing picture elements or have luminous spots. This is not a sign of a malfunction.
Side View |
Top View |
Stand clip
Fixing strap
‘P’ Clip
‘P’ Clip
‘P’ Clip
Make sure the television is located in a position where it cannot be pushed or hit by objects, as pressure will
break or damage the screen, and that small items cannot be inserted into slots or openings in the case.
English
Cleaning the screen and cabinet…
Turn off the power, clean the screen and cabinet with a soft, dry cloth. We recommend that you do not use any proprietary polishes or solvents on the screen or cabinet as this may cause damage.
Please take note
The digital reception function of this television is only effective in the countries listed in the “COUNTRY” section of the “SETUP” menu. Depending on country/area, some of this television's functions may not be available. Reception of future additional or modified services can not be guaranteed with this television.
If stationary images generated by 4:3 broadcasts, text services, channel identification logos, computer displays, video games, on screen menus, etc. are left on the television screen for any length of time they could become conspicuous, it is always advisable to reduce both the brightness and contrast settings.
Very long, continuous use of the 4:3 picture on a 16:9 screen may result in some retention of the image at the 4:3 outlines, this is not a defect of the LCD TV and is not covered under the manufacturers warranty. Regular use of other size modes (eg: Superlive) and varying the “side panel” brightness (if available on the model) will prevent permanent retention.
EXCLUSION CLAUSE
Toshiba shall under no circumstances be liable for loss and/or damage to the product caused by:
i)fire;
ii)earthquake;
iii)accidental damage;
iv)intentional misuse of the product;
v)use of the product in improper conditions;
vi)loss and/or damage caused to the product whilst in the possession of a third party;
vii)any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the owner’s manual;
viii)any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with associated equipment;
Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not limited to the following, loss of profit, interruption of business, the loss of recorded data whether caused during normal operation or misuse of the product.
5
English
INSTALLING YOUR TV
The remote control
Simple at-a-glance reference of your remote control.
2
3
4
7
8
10
11
15
17
18
1For On/Standby mode
2To select external input sources
3Picture still
4To call up text services
5Stereo/bilingual transmissions
6Digital Subtitles or Analogue TEXT Subtitle pages if available
|
10 |
To alter the TV volume |
|
11 |
To mute the TV sound |
|
12 |
In TV mode: To change programme positions |
|
|
In Text mode: To change text pages |
|
13 |
In TV mode: To display on-screen information |
|
|
In Text mode: To access index page in Text mode |
1 |
14 |
To access Quick Menu |
15 |
To display the digital on-screen Programme Guide |
|
5 |
16 |
To exit menus |
6 |
17 |
When using menus the arrows move the cursor on the |
|
|
screen up, down, left or right. Qto confirm your selection |
18To display the on-screen menu
19To return to the previous menu
20Text control buttons
21When in Text mode:
9 |
A |
To reveal concealed text |
|
13 |
B |
To hold a wanted page |
|
|
C |
To enlarge text display size |
|
|
D To select a page whilst viewing a normal |
||
12 |
|
picture |
|
When in TV mode: |
|||
|
|||
14 |
D Analogue time display |
||
16 |
Inserting batteries and effective range of |
||
|
|||
|
|
the remote |
|
19 |
|
Remove the back cover to |
|
20 |
|
reveal the battery |
|
|
compartment and make sure |
21 |
the batteries are inserted the |
|
right way round. Suitable |
||
|
||
|
battery types for this remote |
|
|
are AAA, IEC R03 1.5V. |
Do not combine a used, old battery with a new one or mix battery types. Remove dead batteries immediately to
prevent acid from leaking into the battery compartment. Dispose of them in accordance with instructions on page 46 of this manual. Warning: batteries must not be exposed to excessive heat such as sunshine, fire or the like.
The performance of the remote control will deteriorate beyond a distance of five metres or outside an angle of 30 degrees from the centre of the television. If the operating range becomes reduced the batteries may need replacing.
7Number buttons
8Switch the Audio Description On/Off
9To switch between ATV (analogue television) and DTV (DTV TV/DTV RADIO/DTV TEXT if available)
6
CONNECTING YOUR TV
Connecting external equipment
Before connecting any external equipment, turn off all main power switches. If there is no switch remove the mains plug from the wall socket.
OPTICAL DIGITAL AUDIO OUTPUT
HDMI™ INPUT
SOCKETS
COMPONENT VIDEO INPUT (EXT 3)
SCART 2 (EXT 2)
SCART 1 (EXT 1)
*a decoder could be Digital Satellite or any other compatible
decoder. Antenna/Cable
decoder*
media recorder
Aerial cables: - - - - - - - - - - - - - - - - - - - - -
Connect the aerial to the socket on the rear of the television. If you use a decoder* and/or a media recorder it is essential that the aerial cable is connected through the decoder and/or through the media recorder to the television.
SCART leads: . . . . . . . . . . . . . . . . . . . . . . . . . .
Connect the video recorder IN/OUT socket to the television. Connect the decoder TV socket to the television. Connect the media recorder SAT socket to the decoder MEDIA REC. socket.
Before running Auto Tuning, put your decoder and media recorder to Standby.
The phono sockets alongside the COMPONENT VIDEO INPUT sockets will accept L and R audio signals.
The Digital Audio Output socket enables the connection of a suitable surround sound system. NOTE: this output is always active.
HDMI™ (High-Definition Multimedia Interface) is for use with a DVD decoder or electrical equipment with digital audio and video output.
For acceptable video or PC signal formats through the HDMI terminals, see page 49.
NOTE: Although this television is able to connect to HDMI equipment it is possible that some equipment may not operate correctly.
Illustration represents 32RV635D.
POWER switch
FIXING STRAP
RS-232C port (for service use only)
A wide variety of external equipment can be connected to the back of the television; therefore, the relevant owners manuals for all additional equipment must be referred to for exact instructions.
We recommend SCART 1 for a decoder and SCART 2 for a media recorder.
If connecting S-VIDEO equipment, set the INPUT for EXT 2. See page 39.
If the television automatically switches over to monitor external equipment, return to normal television by pressing the desired programme position button. To recall external equipment, press o to select between DTV, EXT 1, EXT 2, EXT 3,
HDMI 1, HDMI 2, HDMI 3, HDMI 4, PC or ATV.
If rbutton is pressed while viewing DTV mode, the picture on your screen and the SCART output will become a still picture.
When the external input mode is selected while viewing DTV mode, the SCART socket does not output video/audio signals. The SCART output will also be muted in EPG mode.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.
INSTAPORT™ and INSTAPORT logo are trademarks of Silicon Image, Inc. in the United States and other countries.
English
7
English
CONNECTING YOUR TV
Connecting an HDMI™ or DVI device to the HDMI input
The HDMI input on your television receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device.
This input is designed to accept HDCP (High-Bandwidth Digital-Content Protection) programme material in digital form from EIA/CEA-861-D–compliant [1] consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output). For acceptable video signal formats, see page 49.
NOTE:
•Some early HDMI equipment may not work properly with your latest HDMI TV, due to the adoption of a new standard. Please unplug your HDMI cable first and then try setting the following options (Lip Sync, INSTAPORT™) to “Off”. Your early HDMI source should operate properly with your television. See page 40.
•Supported Audio format: Linear PCM, sampling rate 32/ 44.1/48kHz.
To connect an HDMI device
Connect an HDMI cable (type A connector) to the HDMI terminal.
For proper operation, it is recommended that you use an HDMI cable with the HDMI Logo ( ).
•If your HDMI connection is capable of 1080p and/or your television is capable of refresh rates greater than 50Hz, you will need a Category 2 cable. Conventional HDMI/DVI cable may not work properly with this mode.
•HDMI cable transfers both video and audio. Separate analogue audio cables are not required (see illustration).
•See “HDMI 1 Audio” on page 40.
The HDMI 4 terminal is located on the side of the television.
To connect a DVI device
Connect an HDMI-to-DVI adapter cable (HDMI type A connector) to the HDMI 1 terminal and audio cables to the PC/ HDMI1 (AUDIO) socket (see illustration).
•The recommended HDMI-to-DVI adapter cable length is 6.6 ft (2m).
•An HDMI-to-DVI adapter cable transfers video only. Separate analogue audio cables are required.
•See “HDMI 1 Audio” on page 40.
Audio cable for HDMI to television connection
(not supplied)
HDMI-to- DVI
adapter Cable
DVI device
VIDEO |
AUDIO |
DVI /HDCP |
L |
R |
OUT |
|
|
IN |
OUT
L R
NOTE:
To ensure that the HDMI or DVI device is reset properly, it is recommended that you follow these procedures:
•When turning on your electronic components, turn on the television first, and then the HDMI or DVI device.
•When turning off your electronic components, turn off the HDMI or DVI device first, and then the television.
HDMI cable
HDMI device
VIDEO |
AUDIO |
HDMI OUT |
|
L |
R |
||
|
|||
|
|
IN |
OUT
L R
To view the HDMI device video, press the o button to select HDMI 1, HDMI 2, HDMI 3 or HDMI 4 mode.
[1] EIA/CEA-861-D compliance covers the transmission of uncompressed digital video with high-bandwidth digital content protection, which is being standardized for reception of high-definition video signals. Because this is an evolving technology, it is possible that some devices may not operate properly with the television.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
8
CONNECTING YOUR TV
Connecting a computer |
• When PC input mode is selected some of the television’s |
|
|
||
|
features will be unavailable e.g. Manual Settings in the |
|
With either an RGB/PC or an HDMI connection, you |
SETUP menu, Colour, Tint, Sharpness and Black/White |
|
Level in the PICTURE menu. |
||
can watch your computer’s display on the television |
||
• If connecting a certain PC model with a unique PC signal, the |
||
and hear the sound from the televisions speakers. |
||
PC signal may not be detected correctly. |
To connect a PC to the RGB/PC terminal
When connecting a PC to the RGB/PC terminal on the television, use an analogue RGB (15-pin) computer cable and a PC audio cable for the PC/HDMI1 (AUDIO) socket. Select PC from the PC/HDMI 1 Audio options in the AV Connection menu located in the SETUP menu.
the back of your television
To connect a PC to the HDMI terminal
When connecting a PC to the HDMI terminal on the television, use an HDMI-to-DVI adapter cable and an analogue audio cable.
If connecting a PC with an HDMI terminal, use an HDMI cable (type A connector). A separate analogue cable is not necessary (see page 8).
the back of your television
English
Mini D-sub
15 pin connector
Computer
Audio cable for PC to television connection
(not supplied)
RGB PC cable
(not supplied)
Conversion adaptor if required
(not supplied)
To use a PC, set the monitor output resolution on the PC before connecting it to the television. For acceptable PC signal formats, see page 48.
To display the optimum picture, use the PC setting feature (see page 38).
NOTE:
•The PC audio input terminal on the television is shared with the HDMI 1 analogue audio input terminal (see page 39).
•Some PC models cannot be connected to this television.
•An adapter is not needed for computers with a compatible mini D-sub15-pin terminal.
•Depending on the DVD’s title and the specifications of the PC on which you are playing the DVD-Video, some scenes may be skipped or you may not be able to pause during multiangle scenes.
•A band may appear at the edges of the screen or parts of the picture may be obscured. This is due to scaling of the picture by the set, it is not a malfunction.
Computer
HDMI-to-DVI |
Audio cable |
adapter cable |
for PC to |
|
television |
|
connection |
|
(not supplied) |
For acceptable PC and video signal formats, see page 49.
NOTE:
•The edges of the images may be hidden.
•If connecting a certain PC model with a unique PC signal, the PC signal may not be detected correctly.
9
English
CONNECTING YOUR TV
Controls and input connections
A wide variety of external equipment can be connected to the input sockets on the side of the television.
Whilst all the necessary adjustments and controls for the television are made using the remote control, the buttons on the television may be used for some functions.
Illustration represents 32RV635D.
POWER switch
|
|
|
|
Input 3 (side) |
ORANGE LED - Programme |
||
will take priority over |
timer set (digital only) |
||
EXT 3 (back) if both |
RED LED – Programme |
||
connections are used |
timer Active (digital only) |
||
at the same time. |
|
|
RED LED – Standby |
|
|
GREEN LED – On Timer set GREEN LED – Power on |
|
|
Standby
COMMON INTERFACE
The Common Interface is for a Conditional Access Module (CAM).
Contact a service provider.
USB port
To access photo files
HDMI 4 INPUT
(Not available on all models.)
INPUT 3 (EXT 3)
Switching on
If the RED LED is unlit, check that the mains plug is connected to the power supply and press the ! (POWER) button on the left side of the television to switch the television on. If the picture does not appear, press 1 on the remote control, it may take a few moments. The GREEN LED will be lit.
To put the television into Standby, press 1 on the remote control. To view the television, press 1 again. The picture may take a few seconds to appear.
Using the remote control
Press MENU on the remote control to see the menus.
The menu appears as a list of five topics. As each symbol is selected by pressing C or c on the navigation ring on the remote control, its respective options will appear below.
NOTE: The same menu is displayed in DTV (Digital TV) and ATV (Analogue TV) modes; however, some items are greyed out in each case.
To use the options, press B and b on the remote control to move up and down through them and Q, and then, press C or c to select the required choice. Follow the on-screen instructions. The functions of each menu are described in detail throughout the manual.
Using the controls and connections
To alter the volume press – 2 +.
To alter the programme position press b p B.
Press MENU and I, i, U or u to control the sound and picture options.
Press MENU to finish.
An S-video cable provides better picture performance than a composite video cable. If you connect an S-video cable to EXT 3, be sure to disconnect the standard (composite) video cable or the picture performance will be unacceptable.
To select an external input, press o until the appropriate input source is selected as described on page 39.
Please always refer to the owner’s manual of the equipment to be connected for full details.
NOTE: Interactive video games that involve shooting a "gun" type of joystick at an on-screen target may not work with this TV.
10
|
|
|
|
|
|
SETTING UP YOUR TV |
||
Startup Application |
h Press b or B to highlight Start Scan, then press Q. |
|||||||
Before switching on the television, put your decoder |
|
|
|
|
|
|
|
|
|
|
Auto Tuning |
|
|
|
|
||
and media recorder, if applicable, to Standby. |
|
|
Tuning Mode |
|
DTV and ATV |
|
||
To set up the television use the buttons on the |
|
|
|
|
|
|
|
|
|
|
|
|
Start Scan |
|
|
||
remote control as detailed on page 6. |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
Quick Setup |
|
NOTE: If Cable is selected in step 6, additional setting |
||||||
|
options appear in the Auto Tuning screen. See “Ant/ |
a Press the 1 button. The Quick Setup screen will |
Cable In“ section. |
|
The television will start to search for available DTV |
||
appear. This screen will appear the first time that the |
||
and/or ATV channels. The progress bar will indicate |
||
television is switched on and each time Reset TV is |
||
the scan status. |
||
selected. |
||
|
Quick Setup
Menu Language |
English |
|
|
Country |
Germany |
|
|
Primary Subtitle Language |
English |
|
|
Secondary Subtitle Language |
English |
|
|
Primary Audio Language |
English |
|
|
Secondary Audio Language |
English |
You must allow the television to complete the search.
Auto Tuning |
|
|
|
|||
|
Progress |
|
Found |
|||
DTV Tune |
3% |
|
|
|
2 |
|
ATV Tune |
|
|
|
Waiting... |
|
|
|
|
|
|
Channel: C7 |
|
|
|
|
|
|
|
|
|
b Highlight Menu Language and press Cor c to select the menu language.
c Press bto highlight Country and C or c to select. The television will now tune the stations for your country.
d Press Q, the Location screen will appear.
Location
To use the TV for displaying in a store showroom, please select [Store]. [Home] mode is recommended for normal use.
Store
e Press C or c to select Store or Home. For normal home use, select Home.
If the Home option is selected the AutoView option will be activated, allowing the TV to automatically adjust the picture setting based on the user’s individual viewing environment. In most cases this will result in the TV operating with lower energy consumption.
f Press Q. If the Ant/Cable In screen appears, press C or c to select Antenna or Cable.
Ant/Cable In
Antenna
g Press Q, the Auto Tuning start up screen will appear with the option to select between DTV and ATV, DTV or ATV if available. Use C or c to select the appropriate mode.
When the search is complete the television will automatically select position one.
The Auto Tuning screen will display the total number of services found.
i Press C or c to view the DTV (digital channel) or ATV (analogue channel) lists.
j Use b or B to move through the list to select a channel then press Qto view.
In ATV mode some areas may receive duplicate stations. There may not be a clear picture or the signal may be weak, so the station order can be changed using ATV Manual Tuning.
REMEMBER: Press ATV/DTV at any time to select between ATV and DTV (DTV TV/DTV RADIO/DTV TEXT if available) modes.
NOTE: The time will be set automatically by transmission but can be advanced or decreased by using Local Time Setting in the DTV Settings screen.
PLEASE NOTE
The Reset TV menu can also be accessed at any time from the SETUP menu.
English
11
English
SETTING UP YOUR TV
Ant/Cable In (if available)
From this menu, you can set the RF input configuration to cable.
a Press MENU, and select SETUP menu.
b Use b to highlight Ant/Cable In and use C or c to
DTV End Frequency:
This sets the frequency at which the scan will end.
*Valid entry range for frequency items is 113.000-858.00 for C-Book/Other and 114.000-858.00 for Nordig-C. If numbers outside of this range are entered, the values will automatically be set to the min. or max. valid value as appropriate.
select Antenna or Cable.
NOTE: When you attempt to change the Ant/Cable In setting, a warning message will appear followed by PIN entry (if PIN has been set) and prompt for Auto Tuning.
c When Ant/Cable In is set to Cable, the following setting options will be provided in the Auto Tuning screen.
Press B or b to select an item, then press C or c to select your desired option.
DTV Modulation:
You can choose from five QAM modulation settings.
DTV Symbol Rate:
This is the baud rate (KS/s) of the scan.
*Valid entry range for Symbol Rate is 4000-7200. If a number outside of this range is entered, value will be automatically set to the min. or max. valid value as appropriate.
DTV Network ID:
This is the Network ID to be utilized for the scan. This item is greyed out when DTV Scan Type is set to “Full Scan”.
Auto Tuning
Tuning Mode |
|
DTV and ATV |
||
|
|
|
||
|
|
Start Scan |
|
|
|
|
|
|
|
DTV |
|
|
|
|
|
|
|
|
|
Scan Type |
|
Quick Scan |
||
|
|
|
|
|
Start Frequency |
|
Auto |
||
|
|
|
|
|
End Frequency |
|
Auto |
||
|
|
|
|
|
Modulation |
|
Auto |
||
|
|
|
|
|
Symbol Rate |
|
Auto |
||
|
|
|
|
|
Network ID |
|
Auto |
*Valid entry range for Network ID is 1-65535. If a number outside of this range is entered, value will be automatically set to the min. or max. valid value as appropriate.
With the exception of DTV Scan Type and DTV Modulation items, all of the following items will have 2 operating modes. The first is Auto where the values for each item are preset by the system. The second is an Input mode where you will be able to enter a single value in place of the pre-set value. If no channel is currently tuned and the Input state is chosen, a system default value will be shown. However, if a channel is currently tuned when the item is accessed, the value of the current channel will be displayed.
DTV Scan Type:
This item determines whether a Quick Scan or a Full Scan will be executed.
The Quick Scan is a simplified version of the Full Scan that is designed to complete in less time.
DTV Start Frequency:
This sets the frequency from which the scan will begin.
12
SETTING UP YOUR TV
Auto Tuning
NOTE: As new services are broadcast it will be necessary to retune the television in order to view them.
Auto Tuning will completely re-tune the television and can be used to up date the channel list.
It is recommended that Auto Tuning is run periodically to ensure that all new services are added. All current channels and settings, i.e. favourites and locked channels, will be lost.
a Press MENU and use C or c to select SETUP menu. Use b to highlight Auto Tuning. Press Q.
SETUP
Menu Language |
English |
|
|
Country |
Germany |
|
|
Ant/Cable In |
Antenna |
Auto Tuning
ATV Manual Tuning
DTV Manual Tuning
DTV Settings
AV Connection
b A screen will appear warning that previous programmes and settings will be deleted.
Auto Tuning
Previous settings will be lost!
Press EXIT for no change.
Tuning Mode |
DTV and ATV |
Start Scan
Use C or c to select DTV and ATV, DTV or ATV, if available, then highlight Start Scan and press Qto continue with the Auto Tuning.
NOTE: If you have selected "Others" for the Country field in the SETUP menu, and select the tuning mode other than "DTV" , choose the optimum ATV broadcasting system (B/G, I, D/K or L).
The television will start to search for all available DTV and/or ATV services.
You must allow the television to complete the search.
When the search is complete the Auto Tuning screen will display the services found.
c Use b or B to move through the list to select a channel then press Qto view.
ATV Manual Tuning
Tuning
The television can be tuned-in manually using ATV Manual Tuning. For example: if the television cannot be connected to a media recorder/decoder with a SCART lead or when you want to tune-in a station on another System.
Use C and c to move across the screen and select any of the ATV Manual Tuning options. Then use B or b to adjust the settings.
ATV Manual Tuning
System: I
1 I A C 2 0 V C R
1 2 3 4 5 6 7 8 9
1Position:
The number to be pressed on the remote control to tune the channel.
2System:
Specific to certain areas.
3Colour System:
Factory set to Auto, should only be changed if problems are experienced, i.e. NTSC input from external source.
4Skip:
8 means nothing has been saved or the facility to skip the channel is ON. See page 15.
5Signal Class:
The channel classification.
6Channel:
The channel classification and the channel number on which a station is being broadcast.
7Search:
Search up and down for a signal.
8Manual Fine Tuning:
Only used if interference/weak signal is experienced. See page 43.
9Station:
Station identification. Use the B or b and C or c buttons to enter up to seven characters.
To allocate a position on the television for a decoder and media recorder: turn the decoder on, insert a pre-recorded film in the media recorder and press PLAY, then manually tune.
English
13
English
SETTING UP YOUR TV
a Press MENU and using C or c select the SETUP menu. With b highlight ATV Manual Tuning and press Q to select.
SETUP
Menu Language |
English |
|
|
Country |
Germany |
|
|
Ant/Cable In |
Antenna |
Auto Tuning
ATV Manual Tuning
DTV Manual Tuning
DTV Settings
AV Connection
b Use B or b to highlight the position required e.g. we suggest Pos. 0 for a media recorder.
ATV Manual Tuning |
|
|
Pos. |
Channel |
Station |
1 |
C2 |
|
2S10
3C7
4S40
5C22
6C25
7C28
8 C30
Different Channel numbers may be displayed.
c Press Qto select. If the channel is set to skip, Skip must be removed before storing.
d Press c to select System and use B or b to change if required.
ATV Manual Tuning
System: I
1 I A |
C 2 |
0 |
e Then press c to select Search.
f Press B or b to begin the search. The search symbol will flash.
ATV Manual Tuning
Search:
1 I A |
C 2 |
0 |
g Each signal will show on the television, if it is not your media recorder, press B or b again to restart the search.
h When your media recorder signal is found, press c to move along to Station. With B, b, C and cput in the required characters, e.g. VCR.
ATV Manual Tuning
Station: VCR
1 I A |
C 2 |
0 V C R |
i Press Qto save.
j Repeat for each position you want to tune or, press MENU to return to the list of channels and select the next number to tune.
k Press EXIT when you have finished.
l To name external equipment, e.g. DVD on EXT 2, press o to select o2, then select Manual Settings from the SETUP menu.
m Press c to select Label then using B, b, C and c put in the required characters.
Manual Settings
Label: DVD
EXT 2 A D V D
PLEASE NOTE
This television has direct channel entry if the channel numbers are known.
Select the ATV Manual Tuning screen in Step 3. Enter the Position number, the System, then C for standard (terrestrial) channels or S for cable channels and the Channel number. Press Qto save.
14
SETTING UP YOUR TV
Skip
To prevent certain channels from being viewed, positions can be skipped. The remote control must be removed as the channels will still be available using the number buttons. Channels can then be watched as normal using the controls on the television, but the television will not show the skipped channel positions.
a Select ATV Manual Tuning from the SETUP menu.
b Use B or bto highlight the position to be skipped and press Qto select.
ATV Manual Tuning |
|
|||
|
Pos. |
Channel |
Station |
|
|
|
|
|
|
|
1 |
|
C2 |
|
2S10
3C7
4 |
|
S40 |
ABC1 |
|
|
|
|
5 |
|
C22 |
ABC1 |
6C25
7C28
8C30
c Press c to select Skip.
d Use B or b to turn Skip on. Press Q.
8 on the screen indicates a skipped position.
ATV Manual Tuning
Skip: On
1 I A C 2 0
e Press MENU and repeat from Step 2 or press EXIT.
Each position has to be individually selected. To turn Skip off, repeat the procedure for each position.
Skipped positions cannot be selected by PU and Pu or by the controls on the television, but can still be accessed by the number buttons on the remote control.
Sorting positions
Channels may be moved and saved to the position of your choice.
a Select ATV Manual Tuning from the SETUP menu.
b With the list of channels now showing use B or b to highlight the channel you want to move and press c.
The selected channel will be moved to the right of the screen.
ATV Manual Tuning |
|
|
|||
|
Pos. |
|
Channel |
Station |
|
|
|
|
|
|
|
|
2 |
|
S10 |
|
|
|
|
|
|
|
|
|
3 |
|
C7 |
|
|
|
|
|
|
|
|
|
4 |
|
C40 |
ABC1 |
|
|
|
|
|
|
|
|
5 |
|
C22 |
ABC1 |
|
|
|
|
|
|
|
|
1 |
|
C2 |
|
|
6C25
7C28
8C30
c Use B or b to move through the list to your preferred position. As you do so the other channels will move to make room.
d Press C to save your move.
Repeat as necessary, then press EXIT.
English
15