tekmar 722 User Manual
- Data Brochure
4-Way Mixing Valve 722
The 4-Way Brass Mixing Valve 722 is used to mix supply water from a heat source with water
returning from a system. It is designed for use in either closed loop or open loop hydronic systems.
It connects to pipe using standard female NPT threads. The valve provides a maximum leak
through rate of 1% to allow for water expansion during temperature changes. The valve position
can be manually set using the handle. An Actuating Motor 741 can be used to automatically
operate the valve.
Sequence of Operation
When the flap is in the fully closed position,
100% of the boiler supply water is returned
to the boiler and 100% of the heating system
return water is supplied to the system. When
the valve flap is in the fully open position,
100% of the boiler supply water enters the
heating system and 100% of the heating
system return water returns to the boiler.
Mixing of the water takes place when the valve
flap is in an intermediate position.
D 722
09/11
Valve 50% position Valve fully openValve in closed position
Installation
Check the contents of the package. If any of the items listed below are missing or damaged, please refer to the Limited Warranty
and Product Return Procedure on the back of this brochure and contact your wholesaler or local tekmar representative.
• One Mixing Valve & One Data Brochure D 722
IMPORTANT: When mounting the valve, leave a minimum of 4” (10 cm) clearance between the bottom cover and surroundings.
This will ensure that all valve components can be easily serviced.
Clockwise to Open Counter Clockwise to Open
Valve
Closed
from
boiler
to system
5
7
3
9
1
10
0
from
system
Valve
Closed
As delivered, no
changes required.
from
system
to system
5
3
7
1
9
10
Remove the “C” clip from the
shaft. Turn over the indicator
0
plate in order to reverse the
from
scale. Re-install the indicator
boiler
plate, “C” clip and handle.
(components shown below)
to boiler
to boiler
Replacement Parts
The Mixing Valve Handle Kit M3047 contains a replacement
manual valve handle, a brass screw, a “C” clip, and a position
indicator plate.
The Replacement O-Ring kit contains a small, a medium and
a large o-ring. Use M3056 kit for valves 3/4” to 1-1/4”.
brass
screw
handle
“C” clip
indicator plate
1 of 2 © 2011 D 722 - 09/11
Technical Data
Normal
Operating
Range
4-Way Mixing Valve 722 Brass
Literature — D 722
Maximum Operating Pressure — 146 psi (10 bar)
Operating Temperature Range
Valve Body and Vane — CW 617N - EN 12165 Brass
Shaft Seal — EPDM Peroxide “O” ring
Main Seal — EPDM Peroxide “O” ring
W
H
— -20 to 248°F (-28 to 120°C)
Type Pipe Size CV Value Dimension H Dimension W Packaged Weight
722 1-1/4” 21 3-1/4” (82 mm) 3-1/4” (82 mm) 2.2 lbs (980 g)
Acceptable Fluid Media — Chilled and hot water with antifreeze
(max. 60%), consisting of ethylene glycol,
propylene glycol, methanol, ethanol, isopropanol, and anticorrosive compounds.
Not for use with fluids that contain mineral
oil or chlorinated pool water.
Valve Performance 722
0369121518
1.5
3
1
2
ft of head
0.5
1
0
0
Normal
Operating
Range
psi
10 20 30 40 50 60 70 80
0
722
US Gal/min
m3/h
1
0.8
0.6
0.4
0.2
0
m of head
Limited Warranty and Product Return Procedure
Limited Warranty The liability of tekmar under this warranty is limited. The
Purchaser, by taking receipt of any tekmar product (“Product”), acknowledges the terms of the Limited Warranty in effect at the time of such Product
sale and acknowledges that it has read and understands same.
The tekmar Limited Warranty to the Purchaser on the Products sold hereunder
is a manufacturer’s pass-through warranty which the Purchaser is authorized
to pass through to its customers. Under the Limited Warranty, each tekmar
Product is warranted against defects in workmanship and materials if the Product is installed and used in compliance with tekmar’s instructions, ordinary
wear and tear excepted. The pass-through warranty period is for a period of
twenty-four (24) months from the production date if the Product is not installed
during that period, or twelve (12) months from the documented date of installation if installed within twenty-four (24) months from the production date.
The liability of tekmar under the Limited Warranty shall be limited to, at tekmar’s
sole discretion: the cost of parts and labor provided by tekmar to repair defects in
materials and/or workmanship of the defective product; or to the exchange of the
defective product for a warranty replacement product; or to the granting of credit
limited to the original cost of the defective product, and such repair, exchange or
credit shall be the sole remedy available from tekmar, and, without limiting the
foregoing in any way, tekmar is not responsible, in contract, tort or strict product liability, for any other losses, costs, expenses, inconveniences, or damages,
whether direct, indirect, special, secondary, incidental or consequential, arising
from ownership or use of the product, or from defects in workmanship or materials,
including any liability for fundamental breach of contract.
The pass-through Limited Warranty applies only to those defective Products
returned to tekmar during the warranty period. This Limited Warranty does not
cover the cost of the parts or labor to remove or transport the defective Product, or
to reinstall the repaired or replacement Product, all such costs and expenses being
subject to Purchaser’s agreement and warranty with its customers.
Any representations or warranties about the Products made by Purchaser to its
customers which are different from or in excess of the tekmar Limited Warranty are
tekmar Control Systems Ltd., Canada, tekmar Control Systems, Inc., U.S.A.
Head Offi ce: 5100 Silver Star Road, Vernon, B.C. Canada V1B 3K4, 250-545-7749, Fax. 250-545-0650 Web Site: www.tekmarcontrols.com
the Purchaser’s sole responsibility and obligation. Purchaser shall indemnify and
hold tekmar harmless from and against any and all claims, liabilities and damages
of any kind or nature which arise out of or are related to any such representations
or warranties by Purchaser to its customers.
The pass-through Limited Warranty does not apply if the returned Product has
been damaged by negligence by persons other than tekmar, accident, fire, Act
of God, abuse or misuse; or has been damaged by modifications, alterations or
attachments made subsequent to purchase which have not been authorized by
tekmar; or if the Product was not installed in compliance with tekmar’s instructions
and/or the local codes and ordinances; or if due to defective installation of the
Product; or if the Product was not used in compliance with tekmar’s instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, WHICH THE GOVERNING LAW ALLOWS PARTIES TO CONTRACTUALLY EXCLUDE, INCLUDING, WITHOUT LIMITATION, IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, DURABILITY OR DESCRIPTION OF THE PRODUCT, ITS NON-INFRINGEMENT OF ANY
RELEVANT PATENTS OR TRADEMARKS, AND ITS COMPLIANCE WITH OR NONVIOLATION OF ANY APPLICABLE ENVIRONMENTAL, HEALTH OR SAFETY LEGISLATION; THE TERM OF ANY OTHER WARRANTY NOT HEREBY CONTRACTUALLY EXCLUDED IS LIMITED SUCH THAT IT SHALL NOT EXTEND BEYOND
TWENTY-FOUR (24) MONTHS FROM THE PRODUCTION DATE, TO THE EXTENT
THAT SUCH LIMITATION IS ALLOWED BY THE GOVERNING LAW.
Product Warranty Return Procedure All Products that are believed to have
defects in workmanship or materials must be returned, together with a written
description of the defect, to the tekmar Representative assigned to the territory in
which such Product is located. If tekmar receives an inquiry from someone other
than a tekmar Representative, including an inquiry from Purchaser (if not a tekmar
Representative) or Purchaser’s customers, regarding a potential warranty claim,
tekmar’s sole obligation shall be to provide the address and other contact information regarding the appropriate Representative.
Product design, software and literature are Copyright © 2011 by:
tekmar Control Systems Ltd. and tekmar Control Systems, Inc.
2 of 2
All specifications are subject to change without notice.
Printed in Canada. D 722 - 09/11.
Loading...