Supra SW5L70D Use And Care Manual

SUPRA

Contents

Appliance Registration 2

Model and Serial Numbers 2

Safety Instructions 3

Installation Instructions 4N7

Water and Electrical Requirements 8

Operating Guide 9_10

Cycle Selection 11_ 12

Detergent, Detergent Guide 13

WASHER DRYER COMBO

COMBINADA LAVADORA SECADORA

COMBINE LAVE-LINGE/SECHE-LINGE

ELECTRONIC

Model SW5L70D

Care & Cleaning 14

Vacation & Winter Storage 15

Safety Features 16

Fabric Care Symbols 17_19

20_22

Warranty Backcover

Supra Appliances Call Center

1.877.44.SUPRA

SUPRA Appliances

461305725

UL HARMONIZED

Help us Help You...

Before using your Washer Dryer read

this book carefully.

It is intended to help you operate and maintain
your new Washer Dryer properly.

Keep it handy for answers to your questions. If

you don't understand something or need more

help write (include your phone number) :
Technical Service & Support
Supra Appliances

101, 3rd Street,

Kentwood, LA, 70444

Phone: 1.877.44.SUPRA
email: [e-mail]

Write down the model and serial

numbers

You will find them on a label fastened at the rear
of the unit. Before using your washer dryer

please write these numbers here.

Model Number

Serial Number

If you received a

damaged Washer Dryer .....

Immediately contact thed:}veyco :ps_y
dealer or the builder v,*c th_ _ tw_,s

Save Time and Money

Before you request service ....

Check the problem solver (Pages 20 to 22).
It lists causes of minor operating problems
that you can correctyo _;_:i.

Energy - Saving Tips

The power and water consumption of your

Washer Dryer can be minimized if you follow

these suggestions.

• Operate Washer Dryer only in full load,

When you put in a partial cotton load, press the

Super Rinse button. This automates the cycle for

energy needs.

• If you don't need pre-wash avoid using
cycle1.

• Always select cycle 3 for cotton load and

keep temperature at 140.

• Always soak or treat stains before the

wash.

• Always select spin speed 1200 rpm to
reduce moisture content.

If you need Service

To obtain service see the consumer services page

in the back of this book. We' re proud of our service
and want you to be pleased. If for some reason you
are not happy with the service you receive here are

three steps to follow for further help.

FIRST, contact the people who serviced your appli-
ance. Explain why you are not pleased. In most
cases, this will solve the problem.
NEXT,if you are still not pleased write all the details

and call 1.877.44.SUPRA. Explain your problem, a
customer service representative from Supra Appli-
ances Technical service will assist you to get a clo-
sure.

FINALLY, if your problem isstill not resolved, email:
[e-mail]

Supra Appliances Division
Supra Corporation

Tokyo, Japan

Page 2

Page 3

Installation sheet

Tools needed for Installation

Multi wrench
Utility Knife

Channel Lock
Nut driver
Level
Screw driver

- Flat Blade

Parts supplied for installation.

Inlet Water Hose - One Washers - Two

Electrical

Refer to serial plate for specific
electrical requirements

Water

Washer Dryer needs one standard 3/4 inch
water supply faucet with a pressure between

30 to 120 pounds per square inch

Cabinet Dimensions

u

C

_o

.4

rq

-r

Width 23.62 inch

®

Operation Of A Condensing Dryer

The Supra washer dryer combo offers many

improvements in this method of drying, The
condensing chamber (b) is located outside of
the tub assembly reducing the amount of heat

to overcome. This allows for more cooling of
there-circulated air.

The air inside the unit is completely recycled and

never escapes the unit. This eliminates the need
for constantly heating cool outside air as
necessary with traditional flow through (vented)
dryers, resulting in reduced energy consumption.

In a properly designed "ventless" system it is
physically impossible for any air (steam) to escape
the unit because the intake of the fan must equal
the output. The only way air can be forced from
the unit is for additional outside air to be drawn
into the system, creating a positive pressure.

In a ventless system the cool air is passed over
the heater assembly and injected into the drum
creating steam within the unit. The hot, moist
air is then drawn from the drum of the unit and
passed through the condensing chamber where
it is subjected to the cooling effect of the
condensing spray, and the water is collected.
(The effect is similar to having a glass of ice

water sitting on a table and condensation starts
to puddle). The air is then reheated and sent
back into the drum to absorb more moisture.
This cycle is repeated until all moisture is
removed from the air stream.

During the drying cycle water is flowing through
the baffle system of the condenser assembly at
a minimal rate. This cooling water is collected
along with the condensation and pumped out
of the system by the washer pump. Below is a
sketch of the air flow through a ventless system.

Key:
a- Fan motor & heating assembly
b- Condensing chamber
c- Pump
d- Condensation and cooling water discharge
e- Cooling water inlet

To Drain

Page 4

Installation sheet

Installation is extremely important for your Washer Dryer to function correctly. :_: :or: t e

STEP 1

PREPARE WASHER DRYER

1, Carefully remove packaging materials from the outside of the Washer Dryer.
2, The Drain hose pipe and the power cord are tied up, Please unstrap.

3, Unscrew and remove four shipping screws, Remove four spacers, !:_:Je _ ?:_e p_e

4, Loosen two front adjustable Washer Dryer legs and lock nuts, Install Vinyl feet below all

four legs,

STEP 2
INSTALL WASHER DRYER

1, Place the drain hose in the drain facility, Prevent hose from collapsing or becoming damaged,
2, Be sure an air tight connection is not made between the drain hose and stand pipe,
3, For best performance the drain hose should not be restricted in any way,

4, The drain stand pipe should be not be higher than 2,6 ft and not lower than 1,64 ft,

5, Caution must be exercised to avoid collapsing or damaging the drain hose,

6, Strap drain hose to the stand pipe,

7, Thread inlet water hose to cold faucet connection, Tighten by hand until snug, Turn 2/3rd by plyer,
8, Do not OVERTIGHTEN, Repeat step for the machine connections at the back of the unit,
9, Turn cold water supply, Check all connections at the water valve and faucet for leaks,

10, Plug power cord into a grounded 220V, 60Hz approved electrical service protected by a

10 amp fuse or a comparable circuit breaker. The Washer Dryer is grounded through the

third and prong _::V:: t_ _:ie _

11, Slide Washer Dryer into position, Make sure the drain hose remains routed straight

through the clip without collapsing or
12, Level Washer Dryer by turning the leveling legs in or out as necessary,
13, Tighten leg lock nuts,
14, The Washer Dryer must be level on four sides, To properly level use a carpenters level, It is

always a good idea to check for level again after the first few washes and re-level if necessary,

i
i

i|

O

tD
tD

Page 5

Installation Sheet

STEP 3

Final Installation Check List

1, and other te,;::have been removed from thetub.

2, Shipping screws have been removed,

3. Washer Dryer is plugged in to an electric outlet and is properly grounded.

4. Water hose is connected to the faucet with inlet screens and washers.

5. Water is turned on and checked for leaks at faucet and machine end connections.

6. Drain hose is properly located into drain facility and is not collapsed or damaged.

7. Washer Dryer has been properly levelled, all legs firmly on the floor and lock nuts engaged.

8. Water fills properly.

9. Test for proper operation by running the Washer Dryer through a complete cycle.

SW5L70D Test Run

1,Prepare your laundry

2. Select fabric type and Wash cycle Program. Refer to fabric care label for instructions.

3. Load cotton laundry into the drum. Load 6 Ibs. Do not over load. (,o_,::d "t_,:i_i:_o> :_t_ y vs , y

wt

4. Load detergent in dispenser 2 for main wash. Follow detergent guide. Use IowsLds _:detergent.

5. Turn Wash Program knob to select the desired wash cycle.

6. Press the desired buttons.

7. Press dry time button to start drying.

8. Press Start.

9. Verify Washer Dryer is filling with water.

10. Verify Washer Dryer stops filling.

11. Verify drum is turning and the cycle is ON.

12. Verify unit rinses during the rinse cycle.

13. Verify unit spins during spin cycle.

14. Pull on the door to make sure it does not open.

15. Allow the cycle to finish. Release start button to ," oc_ door. (/ ow _ t_o oo_ to "oci'

16. O _ door, take out laundry.

17. Verify laundry is clean and dry. Fold and ut away.
18, Repeat I to 8 for a second cotton load of 6 lbs, Do not overload.

19. Press Antiwrinkle button.

20. Press Start.

21. Check if your clothes _::_ wrinkle free.

Make any corrections necessary to properly complete the installation. If in doubt, call toll-
free 1.877.44.SUPRA for guidance on installation issues.

WARNING

Proper installation is the responsibility of the owner. Service performed as a result of improper setup
adjustment or connection are the responsibility of the installer.

Page 6

Installation sheet

Shipping Screws

Spacers

Spacers

Levelling

Plug and Wall Receptacle

sPa_ers

Plumbing

/

H (7

q

(7J

Page 7

i
i

im

0

(,t}

t_

Water and Electrical Requirements

Electrical

220V, 60Hz 10 Amp fuse or circuit breaker

We recommend an individual branch circuit meant only for the Washer Dryer.
The Washer Dryer is equipped with a power cord and a four prong NEMA 14-30P plug.

Never use an Extension cord

Electrical ground is required on this appliance. This unit is equipped with a four prong grounding plug for
use in a properly installed and grounded outlet.

Warning

Improper connectionof the equipment grounding conductorcan result in a risk of electric shock. Check
with a qualified electrician or servicer if you are in doubt on grounding the appliance. Do not modify the

plug provided with this appliance. Have a qualified electrician install the plug into the wall receptacle if the
plug does not fit the outlet. To prevent risk or fire, electric shock or personal injury all wiring and ground-
ing must be done in accordance with National Electrical Code, local codes and ordinances. The owner of

the appliance is responsible to provide adequate electrical service for this appliance.

Water

Water pressure of 30 to 120 p.s.i, is required to correctlyfill the Washer Dryer. Pressure of less than 30

p.s.i, may cause a failure in the water valve or extended fill time. The inlet valve system may not shut off

correctly. To avoid the possibility of water damage should a hose leak, always have faucets accessible.
Turn off faucet when Washer Dryer is not in use.

Drain Facility

We recommend the height of the standpipe to be not higher than 2.63ft and not lower than 1,64 ft.

Make sure the drain facility is capable of accepting the drain hose pipe in a secure manner.

Flooring

For best performance the unit must be installed on a solidly constructed floor. Wooden floors need
reinforcement to minimize machine vibration. Carpeting and soft tile surfaces are contributing factors in

vibration and may cause the Washer Dryer to move slightly during the spin and dry cycles. Never install
the Washer Dryer on a raised platform or on any weak structure. Proper flooring is the responsibility of
the owner.

Location

We recommend the Washer Dryer not to be installed in areas where water may freeze or boil. The
Washer Dryer maintains some amount of water in its internal components like the valve, pump and in the

hose areas. This can lead to damage to belts, pump, motor, hoses and other components. Make sure the

operating temperature is not above 60 degrees R Your Washer Dryer is a ventless system, therefore it
can be installed in a closet or an in an alcove.

Warning

Your Supra washer Dryer is manufactured for operation on 60Hz AC approved electrical service. This

model is not designed for use on 50 Hz AC electrical service. We do not recommend conversion.

For Technical Assistance or if your Washer Dryer requires service, replacement parts or

accessories contact Supra Appliances Technical Service toll free 1,877,44,SUPRA

Page 8