SSCN-230
Table of contents
Loading...
SA-VE230/WMS230/
SS-CN230/V230
US Model
Canadian Model
SERVICE MANUAL
MICRO SATELLITE SYSTEM
Sony Corporation
Home Audio Company
Shinagawa Tec Service Manual Production Group
9-929-074-12
2001D1600-1
© 2001.4
Ver 1.1 2001. 04
• The SA-VE230 system consists of one unit
of SA-WMS230, one unit of SS-CN230 and
four units of SS-V230.
Photo: SA-WMS230 Photo: SS-V230 Photo: SS-CN230
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION :
with 6 Ω loads both channels driven, from 20 - 150 Hz; rated
50 W per channel minimum RMS power, with no more than
0.8% total harmonic distortion from 250 mW to rated output.
SS-V230 Front and rear speakers
Speaker system Full range, magnetically shielded
Speaker units 5
× 9 cm (2 × 3
5
/8 in.), cone type
Enclosure type Bass reflex
Rated impedance 8 Ω
Power handling capacity
Maximum input power: 100 W
Sensitivity level 86 dB (1W, 1m)
Frequency range 90 Hz - 20,000 Hz
Dimensions (w/h/d) Approx. 70 × 151 × 126 mm
(2
7
/8 × 6 × 5 in.), including front
grille
Mass Approx. 550 g (1 lb 3 oz) each
SS-CN230 Center speaker
Speaker system Full range × 2, magnetically
shielded
Speaker units 5
× 9 cm (2 × 3
5
/8 in.), cone type
Enclosure type Bass reflex
Rated impedance 8 Ω
Power handling capacity
Maximum input power: 120 W
Sensitivity level 88 dB (1W, 1m)
Frequency range 90 Hz - 20,000 Hz
Dimensions (w/h/d) Approx. 301 × 70 × 126 mm
(11
7
/8 × 2
7
/8 × 5 in.), including front
grille
Mass Approx. 1.1 kg
(2 lb 7 oz)
SA-WMS230 Subwoofer
System
Speaker system Active subwoofer, magnetically
shielded
Speaker unit Woofer : 16 cm (6
3
/8 in.),
cone type
Enclosure type Advanded SAW type
Continuous RMS power output
(8 Ω, 20 - 150 Hz, 0.8 % THD)
50 W
Reproduction frequency range
28 Hz - 200 Hz
High frequency cut-off frequency
200 Hz
Input
LINE IN (input pin jack)
General
Power requirements 120 V AC, 60 Hz
Power consumptions 45 W
Dimensions (w/h/d) Approx. 205 × 385 × 385 mm
(8
1
/8 × 15
1
/4 × 15
1
/4 in.), including
front grille
Mass Approx. 10.5 kg
(23 lb 2 oz)
Supplied accessories
Foot pads (20)
Audio connecting cords (2 phono to 2 phono) (3)
Monaural connecting cord (1 phono to 1 phono) (1)
Speaker connecting cords, 10 m (32 ft
9
3
/4 in.) (2)
Speaker connecting cords, 2.5 m (8 ft
2
1
/2 in.) (3)
Design and specifications are subject to change
without notice
2
SA-VE230/WMS230/SS-CN230/V230
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS P AR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMA TIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for A C leakage. Check leakage as
described below.
LEAKAGE
The AC leaka ge from any exposed metal part to earth g round and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT -540A. Follo w the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated A C voltmeter . The “limit” indication
is 0.75 V, so analog meters must have an accurate lo w-v oltage
scale. The Simpson 250 and Sanwa SH-63Trd are e xamples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
SAFETY CHECK-OUT
T o Exposed Metal
Parts on Set
0.15 µF
1.5 kΩ
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an A C v oltmeter to check A C leakage.
3
SA-VE230/WMS230/SS-CN230/V230
SECTION 1
DIAGRAMS
1-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• b : Pattern from the side which enables seeing.
• Indication of transistor.
B
These are omitted.
CE
Q
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and
1
/
4
W or less unless otherwise
specified.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
• A : B+ Line.
• B : B– Line.
• Voltages are dc with respect to ground under no-signal
conditions.
• Voltages are taken with a VOM (input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Signal path.
F : AUDIO
• Circuit Boards Location
SA-WMS230
Note:
The components identi-
fied by mark 0 or dotted
line with mark 0 are criti-
cal for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
POWER board
POWER SWITCH board
LED board
CONTROL board
MAIN boar
d
4
SA-VE230/WMS230/SS-CN230/V230
• IC Block Diagrams
IC302 uPC1237H
1 2 3 4 5 6 7 8
OVER LOAD DET
F/F
OFFSET DET
LATCH/
AUTORESET
V
CC
ON
MUTE
AC OFF
DET
V
CC
55
SA-VE230/WMS230/SS-CN230/V230
1-2. PRINTED WIRING BOARD (SA-WMS230)
• See page 3 for Circuit Boards Location.
There are a few cases that the part printed on
this diagram isn’t mounted in this model.
1-676-565-
IC101
IC102
LED BOARD
LEVEL
MODE
ON : MUSIC
OFF: MOVIE
(POWER)
SP1
(SPEAKER)
11
(13)
11
(13)
11
(13)
12
(13)
MAIN BOARD
POWER
T501
POWER
TRANSFORMER
AC
IN
11
(13)
CONTROL BOARD
POWER SWITCH
BOARD
POWER BOARD
LINE
12
A
B
C
D
E
F
G
H
34567891011
IC103
IC302
IC401
IC201
Ref. No. Location
D301 F-8
D302 F-8
D303 F-5
D304 D-9
D501 G-5
D502 G-7
D503 H-7
D801 B-7
IC101 G-11
IC102 G-9
IC103 E-11
IC201 B-3
IC302 E-9
IC401 B-10
Q101 G-9
Q102 G-8
Q103 E-10
Q303 D-9
• Semiconductor
Location
Loading...