SA-VE215/WMS215/ SS-MS215
SERVICE MANUAL
AEP Model
UK Model
E Model
Australian Model
Chinese Model
• |
This set is the Speaker section in HT-K170/ |
|
|
|
K215. |
|
|
• |
The SA-VE215 system consists of one unit |
|
|
|
of SA-WMS215 and five units of SS-MS215. |
Photo: SA-WMS215 |
Photo: SS-MS215 |
|
|
|
|
SPECIFICATIONS
SS-MS215 Front, center and rear speakers
Speaker system |
Full range, magnetically |
|
shielded |
Speaker units |
5 cm cone type |
Enclosure type |
Bass reflex |
Rated impedance |
8 ohms |
Power handling |
60 watts |
capacity |
|
(Maximum input |
|
power) |
|
Sensitivity level |
84 dB (1W, 1m) |
Frequency range |
150 Hz - 20,000 Hz |
Dimensions (w/h/d) |
Approx. 76 × 100 × 86 mm |
|
including front grille |
Mass |
Approx. 425 g |
SA-WMS215 Subwoofer
System |
Active subwoofer, |
Speaker system |
magnetically shielded |
Speaker unit |
Woofer : 16 cm cone type |
Enclosure type |
Acoustically Loaded Bass Reflex |
Continuous RMS |
50 W |
power output |
|
(8 ohms, 20 - 250 Hz) |
|
Reproduction |
32 Hz - 250 Hz |
frequency range |
|
High frequency |
250 Hz |
cut-off frequency |
|
Input
LINE IN (input pin jack)
General
Power requirements |
220 - 230 V AC, 50/60 Hz |
Power consumptions |
45 W |
Dimensions (w/h/d) |
Approx. 240 × 285 × 355 mm |
|
including front panel |
Mass |
Approx. 8 kg |
Design and specifications are subject to change without notice
SPEAKER SYSTEM
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Flexible Circuit Board Repairing
•Keep the temperature of soldering iron around 270˚C during repairing.
•Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering or unsoldering.
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be damaged by heat.
2
SECTION 1
1-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Printed Wiring Board:
•X: parts extracted from the component side.
•b: Pattern from the side which enables seeing.
•Indication of transistor.
Q
B C E
These are omitted.
Note on Schematic Diagram:
•All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
•All resistors are in Ω and 1/4 W or less unless otherwise specified.
•2: nonflammable resistor.
•C: panel designation.
Note :
The components identified by mark 0or dotted line with mark 0are critical for safety.
Replace only with part number specified.
•U : B+ Line.
•V : B– Line.
•Voltages are dc with respect to ground under no-signal conditions.
•Voltages are taken with a VOM (input impedance 10 MΩ ). Voltage variations may be noted due to normal production tolerances.
•Signal path. F : AUDIO
•Circuit Boards Location SA-WMS215
|
POWER SUPPLY board |
LED board |
POWER IC board |
|
POWER SWITCH board
MAIN board
CONTROL board
• IC Block Diagram
IC302 uPC1237HA
OVER LOAD DET |
|
|
F/F |
VCC ON |
|
MUTE |
||
OFFSET DET |
||
|
||
LATCH/ |
|
|
AUTORESET |
|
|
AC OFF |
|
|
DET |
|
VCC
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
3 3