SS-AZ5DRS/AZ7D/AZ7DMRS/
CT7D/RS7D/WG7D
SERVICE MANUAL |
E Model |
Ver. 1.0 2005.06 |
Australian Model |
|
Photo: SS-AZ7D |
Photo: SS-WG7D Photo: SS-CT7D Photo: SS-RS7D |
|
|
•SS-AZ7D is the front speaker in DHC-AZ2D, AZ5D, AZ3DM, AZ7DM.
•SS-CT7D is the center speaker in DHC-AZ5D, AZ7DM.
•SS-RS7D is the surround speaker in DHC-AZ5D, AZ7DM.
•SS-WG7D is subwoofer in DHC-AZ5D, AZ7DM.
COMPONENT MODEL NAME (SS-AZ5DRS/AZ7DMRS)
|
SS-AZ5DRS |
SS-AZ7DMRS |
|
|
|
Surround Speaker |
SS-RS7D |
|
|
|
|
Center Speaker |
SS-CT7D |
|
|
|
|
Sub Woofer |
SS-WG7D |
|
|
|
|
SPECIFICATIONS
Front speaker SS-AZ7D
Speaker system |
2-way, 3-unit, bass-reflex |
|
type, magnetically |
|
shielded type |
Speaker units |
|
Woofer: |
13 cm, cone type |
Tweeter: |
5 cm, cone type |
Nominal impedance |
4 ohms |
Dimensions (w/h/d) |
Approx. 190 × 381 × |
|
251 mm |
Mass |
Approx. 4.6 kg net per |
|
speaker |
Surround speaker SS-RS7D |
|
Speaker system |
1-way, 1-unit, bass-reflex |
|
type |
Speaker units |
|
Full-range: |
8 cm, cone type |
Nominal impedance |
8 ohms |
Dimensions (w/h/d) |
Approx. 175 × 95 × |
|
101 mm |
Mass |
Approx. 0.6 kg net per |
|
speaker |
Center speaker SS-CT7D
Speaker system |
1-way, 1-unit, bass-reflex |
|
type, magnetically |
|
shielded type |
Speaker units |
|
Full-range: |
8 cm, cone type |
Nominal impedance |
8 ohms |
Dimensions (w/h/d) |
Approx. 175 × 95 × |
|
101 mm |
Mass |
Approx. 0.8 kg |
Subwoofer speaker SS-WG7D |
|
Speaker system |
1-way, 1-unit, bass-reflex, |
|
magnetically shielded type |
Speaker unit |
18 cm, cone type |
Nominal impedance |
2 ohms |
Dimensions (w/h/d) |
Approx. 215 × 537 × |
|
215 mm |
Mass |
Approx. 6.4 kg net per |
|
speaker |
Design and specifications are subject to change without notice
•JIG
When disassembling the set, use the following jig (for speaker removal).
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
SPEAKER SYSTEM
9-879-720-01 |
Sony Corporation |
|
2005F05-1 |
Audio Group |
© 2005.06 |
Published by Sony Engineering Corporation |
SS-AZ5DRS/AZ7D/AZ7DMRS/CT7D/RS7D/WG7D
SECTION 1
DISASSEMBLY
DISASSEMBLY OF SS-WG7D
Note: Follow the disassembly procedure in the numerical order given.
2 dish panel |
1 four bosses |
3 four screws (4 × 25)
4 dish
5 three bosses
6 top panel
5 three bosses
qs wire kit
qd loudspeaker (18cm)
0 base
qa two screws (4 × 25)
9 bottom dish
8 four screws |
four slits |
||
(4 × |
25) |
||
|
7 bottom panel
2