Sony SLV-SE610K, SLV-SX710N, SLV-SE710K, SLV-SE710N, SLV-SX710K User Manual

...
Page 1
3-065-678-11 (1) GB
Video Cassette Recorder
Operating Instructions
PAL
SLV-SE610N/K SLV-SE710N/K SLV-SX710N/K SLV-SE810N/K
© 2001 Sony Corporation
Page 2

WARNING

To prev e nt fire or shock hazard, do no t expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
Mains lead must only be changed at a qualified service shop.
Precautions
Safety
• This unit operates on 220 – 240 V AC, 50 Hz. Check that the unit’s operating voltage is identical with your local power supply.
• If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
• The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.
• Unplug the unit from the wall outlet if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
Installing
• Allow adequate air circulation to prevent internal heat buildup.
• Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
• Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
• Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
• Keep the unit and cassettes a w ay from eq uipment with strong magnets, such as microwav e o ve ns o r large loudspeakers.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to a warm location, moisture may condense inside the VCR and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about three hours before operating the unit.
Caution
Te le visi on prog rammes , f il ms, vid eo tapes a nd ot her materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.
Compatible colour systems
This VCR is designed to record using the PAL (B/G or D/K) or MESECAM (B/G or D/K) colour system and play back using the PAL (B/G or D/K) or MESECAM (B/G or D/K) colour systems. Recording of video sources based on other colour systems cannot be guaranteed.
HOWVIEW
S Development Corporation. The S is manufactured under license from Gemstar Development Corporation.
is a registered trademark of Gemstar
HOWVIEW
system
2
Page 3
Table of contents
Getting Started
Getting Started
Index to parts and controls
4
10
Step 1 : Unpacking
11
Step 2 : Setting up the remote commander
15
Step 3 : Connecting the VCR
19
Step 4 : Tuning your TV to the VCR
22
Step 5 : Setting up the VCR with the Auto Set Up function
25
Step 6 : Setting the clock
Selecting a language
29
Presetting channels
30
Changing/disabling programme
34
positions Setting the Canal Plus deco der
39
(not available on SLV-SE610N/K)
Basic Operations
Playing a tape
44
Recording TV programmes
46
Recording TV programmes using
50
the Dial Timer
(SLV-SE810N/K only)
Recording TV programmes using
55
the ShowView system
(not available on SLV-SE610N/K)
Recording TV programmes using
59
the timer
Additional Operations
Playing/searching at various speeds
63
Setting the recording duration time
65
Synchronized Recording
66
(not available on SLV-SE610N/K)
Checking/changing/cancelling
68
timer settings Recording stereo and bilingual
70
programmes Searching using the Smart Search
73
function Storing, searching and deleting
75
programme information (Smart Search Plus)
Searching using the index function
80
Adjusting the picture
81
Reducing the VCR’s power
83
consumption Changing menu options
84
Editing
Connecting to a VCR or stereo
87
system Basic editing
89
Audio dubbing
90
(SLV-SE810N/K only)
Additional Information
Troubleshooting
91
Specifications
96
Index
98 Back Cover
Quick Start Guide
Table of contents
3
Page 4
Getting Started

Index to parts and controls

Refer to the pages indicated in parentheses ( ) for details.

Front panel

SLV-SE810N/K
(on/standby) switch (19)
A ?/1
Tape compartment
B
Remote se nsor (11)
C
(eject) button (44)
D A
Shuttle ring (63)
E F H
G H z
(play) button (44) (63)
JOG button (64)
REC (record) button (46) (65)
(89)
(pause) button (44) (89)
I X
(stop) button (44) (89)
J x K M L m
(fast-forward) button (44) (63) (rewind) button ( 4 4) (63)
DIAL TIMER (50)
M
PROGRAM +/– buttons (22) (64)
N
(81) AUDIO DUB button (90)
O
AUTO SET UP/
P
RF (Radio Frequency) CHANNEL button (19) (2 2)
SYNCHRO REC (Synchronized
Q
Recording) button (67)
LINE-2 L (left) o R (right)
R t
jacks (covered) (87) (88)
How to open the jack cover
1 Press the bottom of the cover. 2 Hook your finger on the top edge of the
cover and pull it open.
Index to parts and controls
4
Page 5
SLV-SE610N/K, SE710N/K, SX710N/K
Getting Started
(on/standby) switch (19)
A ?/1
Tape compartment
B
Remote se nsor (11)
C
(eject) button (44)
D A
(play) button (44) (63)
E H
REC (record) button (46) (65)
F z
(89)
(pause) button (44) (89)
G X
(stop) button (44) (89)
H x
* not available on SLV-SE610N/K
I M J m
K
(fast-forward) button (44) (63) (rewind) button (44) (63)
PROGRAM +/– buttons (22) (64) (81)
AUTO SET UP/
L
RF (Radio Frequency) CHANNEL button (19) (22)
SYNCHRO REC (Synchronized
M
Recording) button* (67)
continued
Index to parts and controls
5
Page 6

Display window

STEREO NICAM SYNCHRO
Timer indicator (52) (57) (60)
A
1
2
(70)
(67)
1
(17)
SYNCHRO indicator*
B
STEREO indicator (70)
C
NICAM indicator*
D
(smartlink) indicator*
E
VIDEO indicator (16) (47)
F
VPS (Video Programme System)/
G
PDC (Programme Delivery Control)
1
indicator* Tape speed indicators (46)
H
(57)
RR
SPLP OPCVIDEO VPS
PDC EP TV
OPC (Optimum Picture Control)
I
indicator (82)
1
TV indicator*
J
Audio dubbing indicator*
K
Tracking indicator (81)
L
Time counter/clock/line/programme
M
(48)
3
(90)
position indicator (44) (46) (89) Remaining time indicator (47)
N
RR (Reality Regenerator) indicator
O
(81) Tape/recording indicator (46)
P
*1not available on SLV-SE610N/K
2
*
SLV-SE610N, SE710N, SX71 0N, and SE810N only
3
*
SLV-SE810N/K only
Index to parts and controls
6
Page 7

Rear panel

Getting Started
Mains lead (15) (16)
A
DECODER/t LINE-2 IN
B
DECODEUR/t ENTREE LIGNE-
1
2 connector*
(18) (39) (66) (88)
DECODER/t LINE-3 IN DECODEUR/t ENTREE LIGNE­3 connector*
AERIAL IN
C
2
(18) (39) (66) (88)
ANTENNE ENTREE connector (15) (16)
*1SLV-SE710N/K and SX710N/K only
2
*
SLV-SE810N/K only
3
not available on SLV-SE610N/K
*
AERIAL OUT
D
ANTENNE SORTI E connector (15 ) (16)
E i
LINE-1 (TV) LIGNE-1 (TV) connector (16)
i
(39)
(audio out) R/D (right) L/G (left)
F
jacks*
3
(18)
continued
Index to parts and controls
7
Page 8

Remote commander

EJECT button (44)
A Z
123 456 789
0
WIDE button (
B
AUDIO MONITOR button (70)
C
×2 button* (63)
D
SLOW button* (63)
E y
SP (Standard Play)/LP (Long Play)
F
for TV
) (13)
button (46)
DISPLAY button (47)
G
(ten’s digit) button (12) (47)
H -
(volume) +/– buttons (
I 2
for TV
(13)
REC (record) button (46) (65)
J z
MENU button (25) (68)
K
PAUSE/M button (25) (4 4)
L X
STOP/m button (25) (44)
x
REW (rewind)/< button (44)
m
(63)
FF (fast-forward)/, button
M
(44) (63)
PLAY/OK button (25) (44)
H
)
Index to parts and controls
8
* FASTEXT buttons (
SE810N/K only)
for TV
) (SLV-
Page 9
M [TV]
(11)
/
[VIDEO]
remote control switch
Getting Started
123 456 789
0
N ?/1
O
P a
Q ./>
R
S t
T
U
(on/standby) switch (12) (57)
COUNTER/REMAIN button (47)
2
(Teletext) button*
/
(
for TV
TV power on/TV mode select
button*
2
(
for TV
) (12)
INDEX SEARCH
buttons*
1
(80)
CLEAR button (44) (56) (68)
TV/VIDEO button (12) (16) (47) Programme number b uttons (12) (4 7) INPUT SELECT button (47) (60)
(89) PROG (program me) +/– b uttons (12 )
V
(31) (46)
T eletext page access buttons*
c/C
(
) (13)
for TV
TIMER button (55) (59)
W
SMART SEARCH button (73)
X
*1FASTEXT buttons (
SE810N/K only)
2
*
SLV-SE810N/K only
for TV
) (SLV-
) (13)
2
Index to parts and controls
9
Page 10

Step 1 : Unpacking

Check that you have received the following items with the VCR:
• Remote commander • Aerial cable
• R6 (size AA) batteries

Check your model name

The instructions in this manual are for the 8 models: SLV-SE610N, SE610K, SE710N, SE710K, SX710N, SX710K, SE810N, and SE810K. Check your model number by looking at the rear panel of your VCR. SLV-SE810N is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-SE710N only.”
10
Unpacking
Page 11

Step 2 : Setting up the remote commander

123 456 789
0

Inserting the batteries

Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.
Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.

Using the remote commander

You can use this remote commander to operate this VCR and a Sony TV. Buttons on the remote commander marked with a dot (•) can be used to operate your Sony TV. If the TV does not have the symbol near the remote sensor, this remo te commander will not operate the TV.
Remote sensor
Getting Started
To operate Set
the VCR a Sony TV
/
[TV]
[VIDEO]
and point at the remote sensor at the VCR
[TV]
and point at the remote senso r at the TV
[VIDEO]
to
[TV]
/
[VIDEO]
continued
Setting up the remote commander
11
Page 12
WIDE
AUDIO MONITOR
FASTEXT buttons
DISPLAY
-
123 456 789
0
????/1111
/
a
tttt
TV/VIDEO
Programme number buttons
PROG +/–/
c/C
+/–
2222
TV control buttons
To Press
Set the TV to standby mode Select an input source: aerial in or line in Select the TV’s programme positio n Programme number buttons,
Setting up the remote commander
12
?/1
TV/VIDEO
t
, PROG +/–
-
Page 13
To Press
Adjust the volume of the TV Switch to TV (Teletext off)* Switch to Teletext* Select the sound AUDIO MONITOR Use FASTEXT* FASTEXT buttons Call up the on-screen display
Change the Teletext page* Switch to/from wide mode of a Sony wide TV (For
other manufactures’ wide T V s, see “Controlling other TVs with the remote commander (SLV­SE810N/K only)” below.)
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
• Do not use a new battery together with an old one.
• Do not use different types of batteries together.
• Some buttons may not work with certain Sony TVs.
* SLV-SE81 0N /K on ly
2
+/–
(TV)
a
(Teletext)
/
DISPLAY
c/C
WIDE

Controlling other TVs with the remote commander (SLV-SE810N/K only)

The remote commander is preprogrammed to co ntrol non-Son y TVs. If yo ur TV is listed in the following table, set the appropriate manufacturer’s code number.
Getting Started
Set
1
Hold down ?/1, and enter your TV’s code number using the programme
2
number buttons. Then release ?/1.
[TV]
/
[VIDEO]
at the top of the remote commander to
[TV]
.
Now you can use the following TV control buttons to control your TV:
?/1, t
TV/VIDEO, programme number buttons, - (ten’s digit), PROG +/–, 2 +/–, a (TV), / (Teletext), FASTEXT buttons, WIDE*, MENU*,
* These buttons may not work with all TVs.
M/m/</,
*, and OK*.
continued
Setting up the remote commander
13
Page 14
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
To switch to wide mode, see the foo t notes b elow this table for the applicable code numbers.
Manufacturer Code number
Sony
01*1, 02 Akai 68 Ferguson 52 Grundig
10*1, 11*
1
Hitachi 24 JVC 33 Loewe 45 Mivar 09, 70 NEC 66 Nokia
15, 16, 69*
3
Manufacturer Code number
Panasonic Philips
17*1, 49
06*1, 07*1, 08* Saba 12, 13 Samsung 22, 23 Sanyo 25 Sharp 29 Telefunken 36 Thomson
43*
2
Toshiba 38
1
*1Press WIDE to switch the wide picture mode on or off.
2
Press WIDE, then press 2 +/– to select the wide picture mode you want.
*
3
Press WIDE. The menu appears on the TV screen. Then, press M/m/</, to
*
select the wide picture you want an d press OK.
Tip
• When you set your TV’s code number correctly while the TV is turned on, the TV turns off automatically.
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote c ommander, the code number may change. Set the appropriate code number every time you replace the batteries.
Setting up the remote commander
14
Page 15

Step 3 : Connecting the VCR

AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
IN
ENTREE
OUT
SORTIE
AERIAL
ANTENNE
If your TV has a Scart (EURO-AV) connector, see page 16.

If your TV does not have a Scart (EURO-AV) connector

AERIAL IN
AERIAL OUT
Mains lead
to mains
Aerial cable (supplie d)
: Signal flow
Getting Started
AERIAL IN
1
2
3
Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR.
Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable.
Connect the mains lead to the mains.
Note
• When you connect the VCR and your TV only with an aerial cable, you have to tune your TV to the VCR (see page 19).
continued
Connecting the VCR
15
Page 16

If your TV has a Scart (EURO-AV) connector

AERIAL
ANTENNE IN
ENTREE
OUT
SORTIE
IN
ENTREE
OUT
SORTIE
AERIAL
ANTENNE
AERIAL IN
i
Mains lead
to mains
LINE-1
(TV)
: Signal flow
Scart cable (not supplied)
AERIAL OUT
Aerial cable (supplied)
AERIAL IN
Scart (EURO-AV)
1
2
3
4
Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the VCR.
Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable.
Connect LINE-1 (TV) on th e VCR and the Scart (EURO-AV) connector on the TV with the optional Scart cable.
This connection improves picture and sound quality. Whenever you want to watch the VCR picture, press tTV/VIDEO to display the VIDEO indicator in the display win dow.
Connect the mains lead to the mains.
Connecting the VCR
16
Note
• If the TV is connected to the LINE-1 (TV) connector, setting the RF channel to
OFF is recommended. In the OFF position, only the signal from the aerial is output through the AERI AL OUT connector (see page 21).
Page 17

About the SMARTLINK features (not available on SLV-SE610N/K)

If the connected TV complies with SMARTLINK, MEGALOGIC* EASYLINK* VIEW LINK*
2
, Q-Link*3, EURO
4
, or T-V LINK*5, this VCR automatically runs the SMARTLINK function after you complete the steps on the previous page (the indicator appears in the VCR’s display window when you turn on the TV). You can enjoy the following SMARTLINK features.
• Preset Download
You can download your TV tuner preset data to this VCR and tune the VCR according to that data in Auto Set Up. This greatly simplifies the Auto Set Up procedure. Be careful not to disconnect the cables o r exit the Auto Set Up function during the procedure. See “Setting up the VCR with the Auto Set Up function” on page 22.
• TV Direct Rec
You can easily record what you are watching on the TV. For details, see “Recording what you are watching on the TV (TV Direct Rec) (not available on SLV-SE610N/K)” on page 48.
• One Touch Play
With One Touch Play, you can start playback automatically without turning on the TV. For details, see “Starting playback automatically with one button (One Touch Play) (not available on SLV-SE610N/K)” on page
45.
• One Touch Menu
You can turn on the VCR and TV, set the TV to the video channel, and display the VCR’s on-screen display automatically by pressing MENU on the remote commander.
• One Touch Timer
You can turn on the VCR and TV, set the TV to the video channel, and display the timer recording menu (the TIMER METHOD menu, the TIMER menu, or the SHOWVIEW menu) automatically by pressing TIMER on the remote commander. You can set which timer recording menu is displayed using TIMER OPTIONS in the OPTIONS-2 menu (see page 85).
• Automatic Power Off
You can have the VCR turn off automatically, if the VCR is not used after you turn off the TV.
*1“MEGALOGIC” is a registered trademark of Grundig Corporat i on.
2
*
“EASYLINK” is a trademark of Philips Corporation.
3
*
“Q-Link” is a tra demark of Panasonic Corpor ation.
4
*
“EURO VIEW LINK” is a trademark of Toshiba Corpora t ion.
5
*
“T-V LINK” is a trademark of JVC Corporation.
1
,
Getting Started
Note
• Not all TVs respond to the functions above.
continued
Connecting the VCR
17
Page 18

Additional connections

To a stereo system (not available on SLV-SE610N/K)
You ca n improve sound quality by connecting a stereo system to the R/D L/G jacks as shown on the right.
To a satellite or digital tuner with Line Through (not available on SLV-SE610N/K)
Using the Line Through function, you can watch programmes from a satellite or digital tuner connected to this VCR on the TV even when the VCR is turned off. When you turn on the satellite or digital tuner, this VCR automatically sends the signal from the satellite or digital tuner to the TV without turning itself on.
Audio cable (not supplied)
: Signal flow
DECODER/
t
LINE-3 IN*
or DECODER/
t
LINE-2 IN*
: Signal flow
R/D L/G
1
2
Scart cable (not supplied)
LINE IN
LINE OUT
Connecting the VCR
18
Connect the satellite or digital tuner to the DECODER/LINE-3 IN*1 (or
1
DECODER/LINE-2 IN* Set DECODER/LINE3*1 (or DECODER/LINE2*2) to LINE3*1 (or
2
LINE2* Set POWER SAVE to OFF or PARTIAL*
3
Turn off the VCR.
4
2
) in the OPTIONS-2 menu.
2
) connector as shown above.
3
in the OPTIONS-2 menu.
To watch a programme, turn on the satellite or digital tuner and the TV.
Note
• You cannot watch programmes on the TV while recording unless you are recording a satellite or digital programme.
1
SLV-SE810N/K only
*
2
*
SLV-SE710N/K and SX710N/K only
3
*
not available on SLV-SE610N/K
Page 19

Step 4 : Tuning your TV to the VCR

If your TV has a Scart (EURO-AV) connector, see page 21.

If your TV does not have a Scart (EURO-AV) connector

Follow the steps below so that your TV will properly receive the video signals from your VCR.
Getting Started
1 2
3
AUTO
SET UP
RF CHANNEL
????/1111
Press ?/1 (on/standby) to turn on the VCR.
Press RF CHANNEL on the VCR lightly. The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV.
Turn on your TV and select a programme position for the VCR picture.
This programme position will now be referred to as the video channel.
RF CHANNEL
PROGRAM +/–
4
AUTO
SET UP
RF CHANNEL
Press RF CHANNEL. The TV system appears in the display window.
continued
Tuning your TV to the VCR
19
Page 20
5
SONY VIDEO CASSETTE RECORDER
PROGRAM
Press PROGRAM +/– (repeatedly) to select the appropriate TV system for your area. Select “G” for the B/G TV system, or “K” for the D/K TV system.
6
7
Tune the TV to the same channel shown in the VCR display window so that the picture on the right appears clearly on the TV screen.
Refer to your TV manual for TV tuning instructions .
If you select the wrong TV system in step 5, the picture on the right may not appear. Select the appropriate TV system and tune the TV again.
If the picture does not appear clearly, see “To obtain a clear picture from the VCR” below.
AUTO
SET UP
Press RF CHANNEL. You have now tuned your TV to the VCR. Whenever you want to
play a tape, set the TV to the video channel.
RF CHANNEL
To check to see if the TV tuning is correct
Set the TV to the video channel and press PROGRAM +/– on the VCR. If the TV screen changes to a different programme each time you press PROGRAM +/–, the TV tuning is correct.
To obtain a clear picture from the VCR
If the screen does not appear clearly in s tep 6 abo ve, go to step 7 to fi nish this procedure once. Then start again from step 2. After pressing RF CHANNEL in step 2, press PROGRAM +/– while the RF channel is displayed, so that another RF channel appear s. Th en tun e the T V to the new RF channel so that a clear picture appears.
Tuning your TV to the VCR
20
Note
• If you set the wrong TV system, you may have no sound or sound may be distorted.
Page 21

If your TV has a Scart (EURO-AV) connector

Getting Started
1 2
3
AUTO
SET UP
RF CHANNEL
PROGRAM
????/1111
RF CHANNEL
PROGRAM +/–
Press ?/1 (on/standby) to turn on the VCR.
Press RF CHANNEL on the VCR lightly. The factory-preset RF channel appears in the display window. The VCR signal is output through this channel to the TV.
Press PROGRAM +/– to set the RF channel to OFF, and press RF CHANNEL again.
AUTO
SET UP
RF CHANNEL
RF channel set up is complete.
Tuning your TV to the VCR
21
Page 22
Step 5 : Setting up the VCR with the Auto
Set Up functi on
Before using the VCR for the first time, set up the VCR using the Auto Set Up function. With this function, you can set the language for the on-screen display, TV channels, guide channels for the ShowView system*, and VCR clock* automatically.
????/1111
AUTO SET UP
PROGRAM +/–
AUTO
1
2
Setting up the VCR with the Auto Set Up function
22
SET UP
RF CHANNEL
PROGRAM
Hold down AUTO SET UP on the VCR for more than three seconds.
The VCR automatically turns on, and the country abbreviation appears in the display window.
Press PROGRAM +/– to select the abbreviation of your country from the table on page 23.
For some countries, there is a selection of languages to choose from. If your country does not appear, select ELSE.
Page 23
3
AUTO
SET UP
Press AUTO SET UP lightly. The VCR starts searching for all of the receivable channels and
presets them according to the TV system you selected in “Tuning
RF CHANNEL
your TV to the VCR” on page 19. If you want to chan ge t he ord er of the channels or disable un wanted
programme positions, see “Changing/disabling programme positions” on page 34.
If you use the SMARTLINK connection (not available on SLV­SE610N/K), the Preset Download function starts and the indicator flashes in the display window during download.
For SLV-SE710N/K, SX710N/K, and SE810N/K: After the search or download is complete, the current time appears in the display window for any stations that transmit a time signal.
For SLV-SE610N/K: When no more receivable channels can be found, presetting stops and “SET UP” disappears from the display window.
The abbreviations of the countries and la ngua ges are as f ollo ws :
Abbreviation Country Language
CZ Czecho Czech HUN Hungary Hungarian PL Poland Polish SK Slovakia Slovak TR Turkey Turkish RUS Russia Russian ELSE Other countries English
Getting Started
To cancel the Auto Set Up function
Press AUTO SET UP.
Tip
• If you want to change the language for the on-screen display from the one preset in the Auto Set Up function, see page 29.
continued
Setting up the VCR with the Auto Set Up function
23
Page 24
Notes
• If you stop the Auto Set Up function during step 3, you must repeat set up from
step 1.
• Whenever you operate the Auto Set Up function, some of the settings
(ShowView*, timer, etc.) will be reset. If this happens, you have to set them again.
* not available on SLV-SE610N/K
Setting up the VCR with the Auto Set Up function
24
Page 25

Step 6 : Setting the clock

SET :
SELECT :
OK
MENUEXIT :
SETTINGS
RETURN
TUNER CLOCK LANGUAGE
SET :
SELECT :
OK
MENUEXIT :
CLOCK
OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
.1 1 . 2001 MON 0: 00
CONFIRM :
SET :
OK
MENUEXIT :
CLOCK
OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
1 . 1.2001 MON 0 : 00
SELECT :
You must set the time and date on the VCR to use the timer features properly. The Auto Clock Set function (not available on SLV -SE610N/K) works only if a station
in your area is broadcasting a time signal. If the Auto Set Up function did not set the clock correctly for your l o cal area, t r y another station for the Aut o Cl ock Se t fun c ti on.

Setting the clock manually

Getting Started
Before you start
• Turn on the VCR and the TV.
• Set the T V to the video channel.
• Refer to “Index to parts and controls” for button locations.
1
2
MENU
PLAY
OK
PLAY
OK
Press MENU, then press M/m to highlight SETTINGS a n d press OK.
Press M/m to highlight CLOCK, then press OK.
For SLV-SE610N/K, only the clock setting menu appears. Skip the next step and go to step 4.
3
PLAY
OK
Press M/m to highlight MANUAL ADJUST, then press OK.
continued
Setting the clock
25
Page 26
4
CONFIRM :
SET :
OK
MENUEXIT :
CLOCK
OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
8 . 1. 2001 SUN 0 : 00
SELECT :
2
CONFIRM :
SET :
OK
MENUEXIT :
CLOCK
OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
8 . 9. 2001 FRI 0 :00
SELECT :
2
CONFIRM :
SET :
OK
MENUEXIT :
CLOCK
OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
8 . FRI 8 :0 0
SELECT :
21.20019
MENUEXIT :
CLOCK
OFFAUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
8 . FRI 8 :0 0
21
SET :
SELECT :
OK
.20019
Press M/m to set the day.
PLAY
OK
5
6
7
8
PLAY
OK
PLAY
OK
PLAY
OK
MENU
Press , to highlight the month and set the month pressing M/m.
Set the year, hour, and minutes in sequence, pressing , to highlig ht the item to be set, and press M/m to select the digits.
The day of the week is set automatically.
Press OK to start the clock.
Press MENU to exit the menu.
Tips
• To chang e the digits while setting, press < to return to the item to be changed, and select the digits by pressing M/m.
• If you want to return to the previous menu, highlight RETURN and press OK.
Setting the clock
26
Note
• The menu disappears automatically if you don’t pro cee d for more than a few minutes.
Page 27
Changing the station for the Auto Clock Set function
SET :
SELECT :
OK
MENUEXIT :
SETTINGS
RETURN
TUNER CLOCK LANGUAGE
SET :
SELECT :
OK
MENUEXIT :
CLOCK
ON
1 AAB
AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
.8 FRI 8 : 00
12 .20019
CONFIRM :
SELECT :
OK
MENUEXIT :
CLOCK
OFF
AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
FRI 8 : 00
8.ON21.20019
SET :
SELECT :
OK
MENUEXIT :
CLOCK
ON
1 AAB
AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
.8 FRI 8 : 00
12 .20019
(not available on SLV-SE610N/K)
Before you start
• Turn on the VCR and the TV.
• Set the T V to the video channel.
• Refer to “Index to parts and controls” for button locations.
Getting Started
1
2
3
4
MENU
PLAY
OK
PLAY
OK
PLAY
OK
PLAY
OK
Press MENU, then press M/m to highlight SETTINGS a n d press OK.
Press M/m to highlight CLOCK, then press OK.
AUTO ADJUST is highlighted.
Press OK.
Press M/m to highlight ON, then press OK.
continued
Setting the clock
27
Page 28
5
CONFIRM :
SELECT :
OK
MENUEXIT :
CLOCK
AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
FRI 8 : 00
8.
1 AAB
21.20019
CONFIRM :
SELECT :
OK
MENUEXIT :
CLOCK
AUTO ADJUST CLOCK PROGRAM MANUAL ADJUST
.2001 FRI 8 : 00
8. 9
2 CDE
21
PLAY
OK
Press m to highlight CLOCK PROGRAM, then press OK.
6
7
Press M/m repeatedly until the
PLAY
OK
programme position of the station that carries a time signal appears.
If the VCR does not receive a time signal from any station, AUTO ADJUST returns to OFF automatically.
MENU
Tips
• If you set AUTO ADJUST to ON, the Auto Clock Set function is activated
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
• The menu disappears automatically if you don’t pro cee d for more than a few
Press MENU to exit the menu.
whenever the VCR is turned off. The time is adjusted automatically by making reference to the time signal from the station whose programme positio n is displayed in the “CLOCK PROGRAM” row. If you do not need the Auto Clock Set, select OFF.
minutes.
Setting the clock
28
Page 29

Selecting a language

SET :
SELECT :
OK
MENUEXIT :
SETTINGS
RETURN
TUNER CLOCK LANGUAGE
SET :
SELECT
OK
MENUEXIT :
LANGUAGE
:
You can change the on-screen display language from the one you selected with the Auto Set Up function.
Before you start
• Turn on the VCR and the TV.
• Set the T V to the video channel.
• Refer to “Index to parts and controls” for button locations.
Getting Started
1
2
3
4
MENU
PLAY
OK
PLAY
OK
PLAY
OK
MENU
Press MENU, then press M/m to highlight SETTINGS a n d press OK.
Press M/m to highlight LANGUAGE, then press OK.
Press M/m to highlight the desired language, then press OK.
Press MENU to exit the me nu.
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
• The menu di sappears automatically if you don’t proceed for more th an a few minutes.
Selecting a language
29
Page 30

Presetting channels

SET :
SELECT :
OK
MENUEXIT :
SETTINGS
RETURN
TUNER CLOCK LANGUAGE
SET :
SELECT :
OK
MENUEXIT :
TUNER
C
AAB12
PROG. 1
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL OFF
ON
RETURN
SYSTEM D / K
MENUEXIT :
TUNER
CATV
PROG.
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL
ON
RETURN
1
CONFIRM :
SELECT :
OK
SYSTEM
SET :
SELECT :
OK
MENUEXIT :
TUNER
C
AAB12
PROG. 1
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL OFF
ON
RETURN
SYSTEM D / K
If some channels could not be preset using the Auto Set Up function, you can preset them manually.
Before you start
• Turn on the VCR and the TV.
• Set the TV to the video channel.
• Refer to “Index to parts and controls” for button locations.
1
2
3
4
MENU
PLAY
OK
PLAY
OK
PLAY
OK
PLAY
OK
Press MENU, then press M/m to highlight SETTINGS and press OK.
Press M/m to highlight TUNER, then press OK.
Press M/m to highlight NORMAL/ CATV, then press OK.
Press M/m to highlight NORMAL, then press OK.
To preset CATV (Cable Television) channels, select CATV.
Presetting channels
30
Page 31
5
SET :
SELECT :
OK
MENUEXIT :
TUNER
C
AAB12
PROG. 4
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL OFF
ON
RETURN
SYSTEM D / K
Selected programme position
MENUEXIT :
TUNER
C
AAB12
PROG.
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
ON
RETURN
4
CONFIRM :
SELECT :
OK
SYSTEM D / K
• PROG
Press PROG +/– to select the programme position.
Getting Started
6
PLAY
Press M/m to highlight CHANNEL SET, then press OK.
OK
continued
Presetting channels
31
Page 32
7
MENUEXIT :
TUNER
C
27
PROG.
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
ON
RETURN
4
CONFIRM :
SELECT :
OK
SYSTEM D / K
B/G TV system D/K TV system Channel
number in the CHANNEL SET field
Receivable Channel
Channel number in the CHANNEL SET field
Receivable Channel
C02 E2 C02 R1 C03 E3 C05 R6 C04 E4 C06 R7 C05 E5 C12 R12 C06 E6 C13 R2 C07 E7 C14 R3 C08 E8 C15 R4 C09 E9 C16 R5 C10 E10 C17 R8 C11 E11 C18 R9 C12 E12 C19 R10 C21–C69 E21–E69 C20 R11 S01–S41 S1–S41 C21–C69 R21–R69 S42–S46 S01–S05
MENUEXIT :
TUNER
PROG.
NORMAL / CATV CHANNEL SET
SYSTEM
AFT FINE TUNING
B / G
D / K
RETURN
4
ON
CONFIRM :
SELECT :
OK
PAY - TV / CANAL+ OFF
PLAY
OK
Press M/m repeatedly until the channel you want is displayed.
123 456 789
0
The channels appear in the follo wing order:
If you know the number of the channel you want, press the programme number buttons. For example, for channel 5, first press “0” and then press “5.”
8
PLAY
OK
If the TV sound is distorte d or noisy, press M/m to highlight SYSTEM and press OK. Then press M/m to select B/G or D/K so that you get better sound.
Presetting channels
32
Page 33
9
To pres et another programme p ositio n, repeat steps 5 through 7.
Getting Started
10
MENU
Press MENU to exit the me nu.

If the picture is not clear

Normally, the Auto Fine Tuning (AF T) functio n automatically tunes in channels clearly. However, if the picture is not clear, you may also use the manual tuning function.
Press PROG +/– or the programme number buttons to select the
1
programme position for which you cannot obtain a clear picture. Press MENU, then select SETTINGS and press OK.
2
Select TUNER, then press OK.
3
Select FINE TUNING, then press OK.
4
The fine tuning meter appears.
TUNER
SYSTEM D / K NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
RETURN
SET :
Press </, to get a clearer picture, then press MENU to exit the menu.
5
NORMAL C OFF
Note that the AFT (Auto Fine Tuning) setting switches to OFF.
4
PROG.
27
MENUEXIT :
Selected programme position
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Notes
• The menu di sappears automatically if you don’t proceed for more th an a few minutes.
• When adj usting FINE TUNING, the menu may become difficult to read due to interference from the picture being received.
Presetting channels
33
Page 34

Changing/disabling programme positions

RETURN
SET :
SELECT :
OK
MENUEXIT :
LISTS
CHANNEL LIST TIMER LIST
MENUEXIT :
CHANNEL LIST
ERASE PROGRAM
MOVE PROGRAM::
PROG
SELECT :
1 2 3 4 5
AAB CDE
FGH
C C C
C
1 0 5
0
2 3 6
9
NAME
CH
C
27
CLEAR
MENUEXIT :
CHANNEL LIST
PROG
1
2 3 4 5
AAB CDE
FGH
C C C
C
1 0 5
0
2 3 6
9
NAME
CH
C
27
CONFIRM
SET STATION NAME::
SELECT :
OK
After setting the channels, you can change the programme positions as you like. If any programme positions are unused or contain unwanted channels, you can disable them.
You can also change the station names (not available on SLV-SE610N/K). If the station names are not displayed, you can enter them manually.

Changing programme positions

Before you start
• Turn on the VCR and the TV.
• Set the TV to the video channel.
• Refer to “Index to parts and controls” for button locations.
1
2
3
MENU
PLAY
OK
PLAY
OK
PLAY
OK
Press MENU, then press M/m to highlight LISTS and press OK.
Press M/m to highlight CHANNEL LIST, then press OK.
Press M/m to highlight the row which you want to change the programme position, the n press ,.
To display other pages for programme positions 6 to 60, press
repeatedly.
M/m
34
Changing/disabling programme positions
Page 35
4
MENUEXIT :
CHANNEL LIST
CONFIRM
SET STATION NAME::
PROG
SELECT :
1 2
3
4 5
CDE AAB FGH
C C C
C
0 5 1
0
3 6 2
9
NAME
CH
C
27
OK
RETURN
SET :
SELECT :
OK
MENUEXIT :
LISTS
CHANNEL LIST TIMER LIST
PLAY
Press M/m until the selected channel row moves to the desired
OK
programme position.
Getting Started
The selected channel is inserted at the new programme posi tion and t he intermediate channels are displaced to fill the gap.
5
6 7
PLAY
OK
MENU
Press OK to confirm the setting.
To change the programme position of another station, repeat steps 3 through 5.
Press MENU to exit the me nu.
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Note
• The menu di sappears automatically if you don’t proceed for more th an a few minutes.

Disabling unwanted programme positions

After presetting channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons.
Before you start
• Turn on the VCR and the TV.
• Set the T V to the video channel.
• Refer to “Index to parts and controls” for button locations.
1
MENU
Press MENU, then press M/m to highlight LISTS, and press OK.
PLAY
OK
Changing/disabling programme positions
continued
35
Page 36
2
MENUEXIT :
CHANNEL LIST
PROG
1 2 3 4 5
AAB CDE
FGH
C C C
C
1 0 5
0
2 3 6
9
NAME
CH
C
27
ERASE PROGRAM
MOVE PROGRAM::
SELECT :
CLEAR
MENUEXIT :
CHANNEL LIST
PROG
1 2 3 4 5
AAB CDE
FGH
C C C
C
1 0 5
0
2 3 6
9
NAME
CH
C
27
ERASE PROGRAM
MOVE PROGRAM::
SELECT :
CLEAR
MENUEXIT :
CHANNEL LIST
PROG
1 2 3 4 5
AAB CDE
FGH
C C
C
1 0
0
2 3
9
NAME
CH
C
27
ERASE PROGRAM
MOVE PROGRAM::
SELECT :
CLEAR
PLAY
OK
Press M/m to highlight CHANNEL LIST, then press OK.
3
4
5 6
Press M/m to highlight the row
PLAY
OK
CLEAR
which you want to disable.
Press CLEAR. The selected row will be cleared as
shown on the right.
Repeat steps 3 and 4 for any other programme positions you want to disable.
MENU
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Press MENU to exit the menu.
Changing/disabling programme positions
36
Notes
• The menu disappears automatically if you don’t pro cee d for more than a few
minutes.
• Be sure to select the programme position you want to disable correctly. If you
disable a programme position by mistake, you need to reset that channel ma nually.
Page 37

Changing the station names (not available on SLV-SE610N/K)

RETURN
SET :
SELECT :
OK
MENUEXIT :
LISTS
CHANNEL LIST TIMER LIST
MENUEXIT :
CHANNEL LIST
PROG
1 2 3 4 5
AAB CDE
FGH
C C C
C
1 0 5
0
2 3 6
9
NAME
CH
C
27
ERASE PROGRAM
MOVE PROGRAM::
SELECT :
CLEAR
MENUEXIT :
CHANNEL LIST
PROG
1
2 3 4 5
AAB CDE
FGH
C C C
C
1 0 5
0
2 3 6
9
NAME
CH
C
27
CONFIRM
SET STATION NAME::
SELECT :
OK
MENUEXIT :
CHANNEL LIST
CONFIRM OK
NEXT
:
:
PROG
SELECT A CHARACTER :
1
2 3 4 5
AAB CDE
FGH
C C C
C
1 0 5
0
2 3 6
9
NAME
CH
C
27
You can change or enter the station names (up to 5 characters). The VCR must receive channel information (for instance, SMARTLINK information) for station names to appear automatically.
Before you start
• Turn on the VCR and the TV.
• Set the T V to the video channel.
• Refer to “Index to parts and controls” for button locations.
Getting Started
1
2
3
MENU
PLAY
OK
PLAY
OK
PLAY
OK
Press MENU, then press M/m to highlight LISTS and press OK.
Press M/m to highlight CHANNEL LIST, then press OK.
Press M/m to highlight the row which you want to change or enter the station name, then press ,.
To display other pages for programme positions 6 to 60, press
repeatedly.
M/m
4
PLAY
Press ,.
OK
continued
Changing/disabling programme positions
37
Page 38
5
MENUEXIT :
CHANNEL LIST
CONFIRM OK
NEXT
:
:
PROG
SELECT A CHARACTER :
1
2 3 4 5
CAB CDE
FGH
C C C
C
1 0 5
0
2 3 6
9
NAME
CH
C
27
PLAY
OK
Enter the station name.
Press M/m to select a character.
1
Each time you press M, the character changes as shown below.
A
tttt B tttttttt Z tttt a tttt b tttt
tttt z tttt 0 tttt 1 tttt … tttt 9 tttt
(symbols) tttt (blank space) tttt A
2
Press , to set the next character. The next space is highlighted. To correct a character, press </, until the character you want to correct is highlighted, then reset it.
You can set up to 5 characters for the station name.
6
7
Press OK to confirm the new name.
PLAY
OK
MENU
Tip
• If you want to return to the previous menu, highlight RETURN and press OK.
Notes
• The menu disappears automatically if you don’t pro cee d for more than a few
• If you enter a symbol in step 5, it will appear as a blank space in the display
Press MENU to exit the menu.
minutes.
window.
Changing/disabling programme positions
38
Page 39
Setting the Canal Pl us de co de r
(not available on SLV-SE610N/K)
You can watch or record Canal Plus programmes if you connect a decoder (not supplied) to the VCR.

Connecting a decoder

Getting Started
DECODER/t LINE-3 IN* or DECODER/t LINE-2 IN*
i
LINE-1 (TV)
Scart cable (not supplied)
: Signal flow
Scart cable (not supplied)
1
2
Scart (EURO-AV)
AERIAL OUT
Aerial cable (supplied)
Canal Plus decoder
AERIAL IN
Scart (EURO-AV)

Setting Canal Plus channels

To watch or record Canal Plus programmes, set your VCR to receive the channels using the on-screen display.
In order to set the channels correctly, be sure to follow all of the steps below.
Before you start
Turn on the VCR, the TV, and the decoder.
Set the TV to the video channel.
Refer to Index to parts and controls for button locations.
continued

Setting the Canal Plus decoder (not available on SLV-SE610N/K)

39
Page 40
1
RETURN
SET :
SELECT :
OK
MENUEXIT :
OPTIONS
OPTIONS - 1 OPTIONS - 2
SET :
SELECT :
OK
MENUEXIT :
OPTIONS - 2
TIMER OPTIONS
DECODER / LINE3 POWER SAVE
VARIABLE
DECODER OFF
TV DIRECT REC ON
NORMALRR
RETURN
MENUEXIT :
OPTIONS - 2
TIMER OPTIONS
DECODER / LINE3 POWER SAVE
TV DIRECT REC
LINE3
DECODER
ON NORMALRR
RETURN
CONFIRM :
SELECT :
OK
SET :
SELECT :
OK
MENUEXIT :
OPTIONS - 2
TIMER OPTIONS
DECODER / LINE3 POWER SAVE
VARIABLE
DECODER OFF
TV DIRECT REC ON
NORMALRR
RETURN
MENU
PLAY
OK
Press MENU, then press M/m to highlight OPTIONS and press OK.
2
3
4
5
PLAY
OK
PLAY
OK
PLAY
OK
MENU
Press M/m to highlight OPTIONS-2, then press OK.
Press M/m to highlight DECODER/ LINE3*
1
(or DECODER/LINE2*2),
then press OK.
Press M/m to highlight DECODER, then press OK.
Press MENU to exit the menu. The menu disappears from the TV screen.
Setting the Canal Plus decoder (not available on SLV-SE610N/K)
40
Page 41
6
SET :
SELECT :
OK
MENUEXIT :
SETTINGS
RETURN
TUNER CLOCK LANGUAGE
SET :
SELECT :
OK
MENUEXIT :
TUNER
C
AAB12
PROG. 1
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL OFF
ON
RETURN
SYSTEM D / K
MENUEXIT :
TUNER
CATV
PROG.
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL
ON
RETURN
1
CONFIRM :
SELECT :
OK
SYSTEM
SET :
SELECT :
OK
MENUEXIT :
TUNER
C
AAB
12
PROG. 1
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL OFF
ON
RETURN
SYSTEM D / K
SET :
SELECT :
OK
MENUEXIT :
TUNER
C
AAB
12
PROG.
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL OFF
ON
RETURN
51
SYSTEM D / K
Selected programme position
MENU
PLAY
OK
Press MENU again. Then press M/
m
to highlight SETTINGS an d press
OK.
Getting Started
7
8
9
10
PLAY
OK
PLAY
OK
PLAY
OK
PROG
Press M/m to highlight TUNER, then press OK.
Press M/m to highlight NORMAL/ CATV, then press OK.
Press M/m to highlight NORMAL, then press OK.
To preset CATV (Cable Television) channels, select CATV.
Press PROG +/– to select the desired programme position.
continued
Setting the Canal Plus decoder (not available on SLV-SE610N/K)
41
Page 42
11
MENUEXIT :
TUNER
C
AAB12
PROG.
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
ON
RETURN
51
CONFIRM :
SELECT :
OK
SYSTEM D / K
SET :
SELECT :
OK
MENUEXIT :
TUNER
C
LMN
02
PROG. 5
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL OFF
ON
RETURN
1
SYSTEM D / K
MENUEXIT :
TUNER
PROG. 5
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL ON
OFF
RETURN
1
CONFIRM :
SELECT :
OK
SYSTEM D / K
SET :
SELECT :
OK
MENUEXIT :
TUNER
C
LMN
02
PROG. 5
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
NORMAL ON
ON
RETURN
1
SYSTEM D / K
MENUEXIT :
TUNER
PROG. 5
NORMAL / CATV CHANNEL SET PAY - TV / CANAL+ AFT FINE TUNING
B / G ON
ON
RETURN
1
CONFIRM :
SELECT :
OK
SYSTEM D / K
PLAY
OK
Press M/m to highlight CHANNEL SET, then press OK.
12
13
14
15
PLAY
OK
PLAY
OK
PLAY
OK
PLAY
OK
Press M/m to select the Canal Plus channels, then press OK.
Press M/m to highlight PAY-TV/ CANAL+, then press OK.
Press M/m to highlight ON, then press OK.
If the TV sound is distorte d or noisy, press M/m to highlight SYSTEM and press OK. Then press M/m to select B/G or D/K so that you get better sound.
Setting the Canal Plus decoder (not available on SLV-SE610N/K)
42
Page 43
16
MENU
Tip
If you want to return to the previous menu, highlight RETURN and press OK.
Notes
The menu disappears automatically if you dont proceed for more than a few
To superimpose subtitles while watching Canal Plus programmes, make both
When yo u wat ch Canal Plus progr a mmes through the RFU input of the TV, press
If POWER SAVE is set to FULL, yo u cannot watch or re cord Canal Plus
*1SLV-S E 81 0N / K on ly
2
*
Press MENU to exit the me nu.
minutes.
decoder-VCR and VCR-TV connections using 2 1-pi n Scart cables that are compatible with the RGB signals. You cannot record subtitles on the VCR.
t
TV/VIDEO so that the VIDEO indicator appears in the display window.
programmes during standby mode. Set POWER SAV E i n the OPTIONS-2 menu to OFF or PARTIAL.
SLV-SE710N/K and SX710N/K only
Getting Started
Setting the Canal Plus decoder (not available on SLV-SE610N/K)
43
Page 44
Basic Operations

Playing a tape

Before you start...
Refer to Index to parts and cont r ols for button locations.
1 2
3
Turn on your TV and set it to the video channel.
Insert a tape. The VCR turns on and starts playing
automatically if you insert a tape with its safety tab removed.
Press H PLAY.
PLAY
OK
When the tape reaches the end, it will rewind automatically.
Additional tasks
To Press
Stop play Pause play Resume play after pause Fast-forward the tape Rewind the tape Eject the tape
x
STOP
X
PAUSE
X
PAUSE or HPLAY
M
FF during stop
m
REW during stop
Z
EJECT
To set the colour system
If the playback picture has no colour, or streaks appear during playback, set COLOUR SYSTEM in the OPTIONS-1 menu to conform to the system that the tape was recorded in (see page 85). (Normally set the option to AUTO.)
Playing a tape
44
To use the time counter
Press CLEAR at the point on the tape that you want to find later. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter.
SP OPCVIDEO
To display the counter on the TV screen, press DISPLAY.
Page 45
Notes
The counter resets to 0:00:00 whenever a tape is reinserted.
The coun ter stops counting when it comes to a portion with no recording.
The time counter does not appear on the TV screen when using an NTSC-recorded
tape.
Depending on your TV, the following may occ ur while playing an NT SC- recorded
tape:
The pict ure becomes black and white.The picture shakes.No picture appears on the TV screen.Black streaks appear horizontally on the TV screen.The colour density increases or decreases.
If you play back a tape in LP or EP mode with the NTSC system, th e sound
becomes monaural.
The pictures colour may be affected when playing a MESECAM-recorded tape in
the LP mode.
While setting the menu on the TV screen, buttons for playback on the remote
commander do not function.

Starting playback automatically with one button (One Touch Play) (not available on SLV-SE610N/K)

If you use the SMARTLINK connection, you can turn on the VCR and the TV, set the TV to the video channel, and start playback automatically with one button.
Insert a tape.
1
The VCR automatically turns on. If you insert a tape with its safety tab removed, the TV turns on and
switches to the video channel. Playback starts automatically. Press H PLAY.
2
The TV turns on and switches to the video channel automatically. Playback starts.
Basic Operations
Tip
When there already is a tape in the VCR, the VCR and the TV turn on, the TV is
set to the video channel, and playback starts automatically in one sequence when you press HPLAY.
Note
When you use the One Touch Play function, leave the TV on or in the standby
mode.
Playing a tape
45
Page 46

Recording TV programmes

Before you start...
Refer to Index to parts and cont r ols for button locations.
1 2
3
4
5
PROG
SP / LP
REC
Turn on your TV and set it to the video channel. To record from a decoder, turn it on.
Insert a tape with its safety tab in place.
Press PROG +/– to select the programme position or station name* you want to record.
SP OPCVIDEO
Press SP/LP to select the tape speed, SP or LP. LP (Long Play) provides recording time twice as long as SP.
However, SP (Standard Play) produces better picture and audio quality.
LP OPCVIDEO
Press z REC to start recording. The recording indicator lights up red in the display window.
Recording indicator
LP OPCVIDEO
To stop recording
Press x STOP.
Recording TV programmes
46
Page 47
To check the remaining time
61:4
Safety tab
Press DISPLAY. With the display on, press COUNTER/REMAIN to check the remaining time. Each time you press COUNTER/REMAIN, the time counter and the remaining time appear alternately. The indicator indicates the remaining time.
SP 20:00:2
Remaining timeTime counter
In order to get an accurate remaining time indication, be sure TAPE LENGTH in the OPTIONS-1 menu is set according to the tape type you use (see page 85).
To watch another TV programme while recording
Press tTV/VIDEO to turn off the VIDEO indicator in the display
1
window. Select another programme position on the TV.
2
To save a recording
To prevent accidental erasure, break off the safety tab as illustrated. To record on the same tape again, cover the tab hole with adhesive tape.
Tips
To sele ct a progr amme p osition, yo u can u se the prog ramme numbe r butt ons on th e remote commander. For two-digit numbers, press the - (tens digit) button followed by the programme number buttons.
If you conne ct additional equipment to a LINE connector or jack, you can select the input signal using the INPUT SELECT or PROG +/– buttons.
The DISPLAY information appears on the TV screen indicating information about the tape, but the information won’t be recorded on the tape.
If you dont want to watch TV while rec ording, you can turn off the TV. When using a decoder, make sure to leave it on.
Basic Operations
continued
Recording TV programmes
47
Page 48
Notes
The DISPLAY information does not appear during still (pause) mode or slow-
motion playback.
The DISPLAY information will not appear while playing an NTSC-recorded
tape.
If a tape has portions recorded in both PAL (MESECAM) and NTSC systems, the
time counter reading will not be correct. This discrepancy is due to the difference between the counting cycles o f the two video systems.
You cannot watch a Canal Plus programme whil e recording another C anal Plus
programme.*
When you insert a non-standard commercially available tape, the remai ni ng time
may not be correct.
The remaining time is intended for rough measurement only.
About 30 seconds after the tape begins playback, the tape remaining time will be
displayed.
The station name* may not appear if the VCR does not receive station name
information signals.
* not available on SLV-SE610N/K

Recording what y ou are watching on the TV (TV Direct Rec) (not avail a ble on SLV-SE610N/K)

If you use the SMARTLINK connection, you can easily record what you are watching on the TV (other than tapes being played on the VCR).
Insert a tape with its safety tab in place.
1
Press z REC while you are watching a TV programme or external
2
source. The VCR automatically turns on, then the TV indicator lights up and the
VCR starts recording what you are watching on the TV.
Tips
The TV indicator appears in the display window after you press zREC in some
situations such as:
when you ar e watching a source connected to the TVs line input, orwhen the TV tuner preset data for the programme position is different from the
If there is a tape with its safety tab in place in the VCR, the VCR automatically
turns on and starts recor ding what you are watching on the TV when you press
z
You can turn the TV Direct Rec function ON and OFF i n the OPTIONS-2 menu
(see page 86).
Recording TV programmes
48
data in the VCR tuner preset.
REC.
Page 49
Notes
You cannot recor d what you are watching using this method when the VCR is in the following modes; pause , timer sta ndb y, tuner preset, Auto Set Up, and recording.
When the TV indicator is lit in the display window, do not turn off the TV nor change the TV programme position. When the TV indicator is not lit, the VCR continues recording the programme even if you change the TV programme position on the TV.
Basic Operations
Recording TV programmes
49
Page 50
Recording TV programmes using the Dial Timer
(SLV-SE810N/K only)
The Dial Timer function allows you to
????/1111
DIAL TIMER
x
make timer recordings of programmes without turning on your TV. Set the recording timer to record up to eight programmes, including settings made with other timer methods, that will be broadcast within the next month. The recording start time and recording stop
PROGRAM +/–
X
time can be set at one minute intervals.
Before you start...
Insert a tape with its safety tab in place. Make su re the ta pe is lon g er tha n the total recording time.
To record from a decoder, turn it on.
Refer to Index to parts and cont r ols for button locations.
1
DIAL TIMER
Press DIAL TIMER. DA TE and TODA Y appear alternately in the display window. If the date and time are not set, “DA Y” will appear . See step 2 in the
following section, To set th e clock to set the date and time.
SP OPCVIDEO
DIAL TIMER
2

Recording TV programmes using the Dial Timer (SLV-SE810N/K only)

50
Turn DIAL TIMER to set the recording date.
SP OPCVIDEO
SP OPCVIDEO
Page 51
3
DIAL TIMER
Press DIAL TIMER. START and the current time appear alternately in the display
window.
SP OPCVIDEO
SP OPCVIDEO
Basic Operations
4
5
6
DIAL TIMER
PROGRAM
DIAL TIMER
DIAL TIMER
PROGRAM
Turn DIAL TIMER to set the recording start time. You can set the recording start time in 15 minute intervals or adjust
the time in one minute intervals by pressing the PROGRAM +/– buttons.
SP OPCVIDEO
Press DIAL TIMER. STOP and the recording stop time appear alternately in the display
window.
SP OPCVIDEO
SP OPCVIDEO
Turn DIAL TIMER to set the recording stop time. You can set the recording stop time in 15 minute intervals or adjust
the time in one minute intervals by pressing the PROGRAM +/– buttons.
SP OPCVIDEO
continued
Recording TV programmes using the Dial Timer (SLV-SE810N/K only)
51
Page 52
7
DIAL TIMER
Press DIAL TIMER. The programme position or station name appears in the display
window.
SP OPCVIDEO
8
9
DIAL TIMER
Turn DIAL TIMER to set the programme position. To record from a decoder or other source connected to one or more
of the LINE inputs, turn
DIAL TIMER or press INPUT SELECT
to display the connected line in the display window.
INPUT SELECT
DIAL TIMER
Press DIAL TIMER to complete the setting.
SP OPCVIDEO
OK appears in the display window for about five seconds. The indicator appears in the display wind o w and the VCR stands
by for recording. To record from a decoder or other source, leave the connected
equipment switched on.
To return to the previous step
To return to the previous step, press the PROGRAM + and – buttons on the VCR at the same time during any of the Dial Timer settings.
To stop recording
To stop the VCR while recording, press x STOP.
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The indicator turns off and the VCR switches on. Remember to press ?/1 to reset the VCR to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
Reset the counter (page 44).
Display tape information on the TV screen (page 47).
Check the timer settings (page 68).
Watch another TV programme (page 47).
Recording TV programmes using the Dial Timer (SLV-SE810N/K only)
52
Page 53
To set the clock
Turn DIAL TIMER so that “CLOCK” appears in the display window.
1
Press DIAL TIMER.
2
DA Y appears in the display window. Turn DIAL TIMER to set the day.
3
Press DIAL TIMER.
4
MONTH appears in the display window. Turn and press DIAL TIMER to set the month, and then the year.
5
After you set the year, “CLOCK” appears in the display window again. Turn and press DIAL TIMER to set the hour and minute.
6
When you have finished setting the time, press DIAL TIMER to start
7
the clock.
Tips
To cancel a Dial T ime r setting, press x (stop) on the VCR the setting.
The programme is recorded in the current tape speed mode. To change the tape speed, press SP/LP before you complete the setting in step 9.
When you ar e recording a programme in the SP mode and the remaining tape becomes shorter than the recording time, the tape speed is automatically changed to the LP mode. Note that some interference will appear on the picture at the po int the tape speed is changed. If you want to keep the same tape speed, set AUTO LONG PLAY to OFF in the OPTIONS-1 menu (page 85).
To check, change, or cancel th e pr ogramme setting, see Checking/changing/ cancelling timer settings” (page 68).
while you are making
Basic Operations
Notes
If eight prog rammes have already been set using the ShowView system or the TIMER menu, “FULL” appears in the display window for about five seconds.
The indicator flashes in the display window when you complete the setting in step 9 with no tape inserted.
If you set the clock using the Auto Clock Set func tion and AUTO ADJUST is set to ON, the clock will adjust itself to the incoming time signal regardless of adjustments made with the Dial Timer. Be sure you have set the Auto Clock Set correctly.
The stati on name may not appear if t he VCR does not receive station name information signals.
continued
Recording TV programmes using the Dial Timer (SLV-SE810N/K only)
53
Page 54

About the Demonstration Mode

The Dial Timer function has a Demonstration Mode that allows the user, such as a salesperson, to enter more than eight examples of timer settings when demonstrating the use of the Dial Timer. It cancels the FULL notice which appears if eight programmes have already been set. Do not use the Demonstration Mode for making timer recordings. Doing so may cause the settings to be inaccurate.
To activate the Demonstration Mode
Press X (pause) on the VCR appears in the display window for a few seconds.
To cancel the Demonstration Mode
Turn the power off and unplug the mains lead. Although the Demonstration Mode is cancelled, the timer settings entered while using the Demonstration Mode will remain. Be sure to manually cancel the timer settings before you use the Dial Timer or any other timer method after reconnecting the mains lead (see page 68).
while turning the DIAL TIMER. “DEMO”
Recording TV programmes using the Dial Timer (SLV-SE810N/K only)
54
Page 55
Recording TV programmes using the
SET :
SELECT :
OK
MENUEXIT :
TIMER METHOD
STANDARD SHOWVIEW
MENUEXIT :
SHOWVIEW
SET :
0–9
SHOWVIEW NO.
––––––– –
FRI28 .9
ShowView system
(not available on SLV-SE610N/K)
The ShowView system is the feature that simplifies programming the VCR to make timer recordings. Just enter the ShowV ie w number listed in the TV programme guide. The date, times, and programme position of that programme are set automatically. You can preset a total of eight programmes, including settings made with other timer methods.
Basic Operations
Before you start
Check that the VCR clock is set to the correct time and date.
Insert a tape with its safety tab in place. Mak e sure the tape is longer than the to tal re c ordin g
time.
To record from a decoder, turn it on.
Turn on your TV and set it to the video channel.
Set TIMER OPTIONS to SHOWVIEW or VARIABLE in the OPTIONS-2 menu (see page
85).
Refer to Index to parts and controls for button locations.
TIMER
1
Press TIMER.
When you set TIMER OPTIONS to VARIABLE: The TIMER METHOD menu
PLAY
OK
appears on the TV screen. Press
M/m
to select SHOWVIEW, then
press OK.
When you set TIMER OPTIONS to SHOWVIEW: The SHOWVIEW menu appears on the TV screen.
continued

Recording TV programmes using the ShowView system (not available on SLV-SE610N/K)

55
Page 56
2
MENUEXIT :
SHOWVIEW
SET :
0–9
SHOWVIEW NO.
1246––– –
FRI28 .9
CANCEL
CONFIRM::
OK
CLEAR
DATE
CANCEL
SET::
SELECT :
CLEAR
MENUEXIT :
TIMER
SP / LP LIST
TIME PROG.
TODAY 519 :00 20: 00 3
SP VPS / PDC OFF
FRI28 .9
DATE
CANCEL
SET::
SELECT :
CLEAR
MENUEXIT :
TIMER
SP / LP LIST
TIME PROG.
TODAY 519 :00 20: 00 3
SP VPS / PDC ON
FRI28 .9
123 456 789
0
CLEAR
Press the programme number buttons to enter the ShowView number.
If you make a mistake, press CLEAR and re-enter the correct number.
3
4
PLAY
OK
INPUT SELECT
CLEAR
PLAY
OK
Press OK. The date, start and stop times,
programme position or station name, tape speed, and VPS/PDC setting appear on the TV screen.
If “– –” appears in the PROG.
(programme) column (this may happen for local broadcasts), you have to set the appropriate programme position manually. Press M/m to select the desired programme position. To record from a decoder or other source connected to one or more of the LINE inputs, press INPUT SELECT to display the connected line in the “PROG. position. You will only have to do this operation once for the referred channel. The VCR will then store your setting.
If the information is incorrect, press CLEAR to cancel the setting.
If you want to change the date, tape speed, and the VPS/PDC setting:
1
Press </, to highlight the item you want to change.
2
Press M/m to reset it.
To record the same programme
every day or the same day every week, see Daily/weekly recording on page 57.
T o use the VPS/PDC function, set VPS/PDC to ON. For details of
the VPS/PDC function, see Timer recording with VPS/PDC signals on page 57.
5
56
Recording TV programmes using the ShowView system (not available on SLV-SE610N/K)
MENU
Press MENU to exit the menu.
Page 57
6
Press ?/1 to turn off the VCR. The indicator appears in the display window and the VCR stands
by for recording. To record from a decoder or other source, leave the connected
equipment switched on.
To stop recording
To stop the VCR while recording, press x STOP.
Daily/weekly recording
In step 4 above, press m to select the recording pattern. Each time you press
m
, the indication changes as shown below . Press M to change the indication
in reverse order.
TODAY t SUN-SAT (Sunda y to Satur d ay) t MON-SAT (Monday to
Saturday) t MON-FRI (Monday to Frid ay ) t SAT (every Saturday) .....
t MON (every Monday) t SUN (every Sunday) t 1 month later t (dates count down) t TOMORROW t TODAY
Timer recor ding with VPS/PDC signals
Some broadcast systems transmit VPS (Video Programme System) or PDC (Programme Delivery Control) signals with their TV programmes. These signals ensure that your timer recordings are made regardless of broadcast delays, early starts, or broadcast interruptions (when the VPS or PDC indicator in the display window is lit).
T o use the VPS /PDC function, set VPS/PD C to ON in step 4 abo ve. You can also use the VPS/PDC function for a source connected to one or more of the LINE inputs.
To record satellite broadcasts
If you connect a satellite tuner and the VCR, you can record satellite programmes.
Turn on the satellite tuner.
1
On the satellite tuner, select the satellite programme for which you want
2
to make a timer setting. Follow steps 1 through 6 above.
3
Keep the satellite tuner turned on until the VCR finishes recording the
4
satellite programme for which you have made a timer setting.
Basic Operations
continued
Recording TV programmes using the ShowView system (not available on SLV-SE610N/K)
57
Page 58
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The indicator turns off and the VCR switches on. Remember to press ?/1 to reset the VCR to recording standby after using the VCR.
You can also do the following tasks while the VCR is recording:
Reset the counter (page 44).
Display tape information on the TV screen (page 47).
Check the timer settings (page 68).
Watch another TV programme (page 47).
Tips
To set the programme position, you c an also use the PROG +/– or program me number buttons.
To set the programme position wi th a two digit number, press - (tens digit) button followed by the programme number buttons.
To set the line input video source, you can also use the PROG +/ buttons.
To set the tape speed, you can also use the SP/LP button.
When you are reco rding a programme in the SP mode and the remaining tape
becomes shorter than the record ing time, the tape speed is automat ically changed to the LP mode. Note that some interference will appear on the pictu re at the poin t the tape speed is changed. If you want to keep the same tape speed, set AUTO LONG PLAY to OFF in the OPTIONS-1 menu (page 85).
To check, change, or cancel the programme setting, press </, to choose LIST, then press OK in step 4. For details, see step 3 in “Checking/changing/cancelling timer settings (page 68).
Notes
If the VPS/PDC signal is too weak or the broadcasting station failed to transmit VPS/PDC signals, the VCR will start recording at the set time without using the VPS/PDC functio n.
The indicator flashes in the display wind ow when you press ?/1 with no tape inserted.
When you set TIMER OPTIONS to STANDARD in the OPTIONS-2 menu, the SHOWVIEW menu does not appear on the TV screen. Select SHOWVIEW or VAR IA BL E.
The VPS/PDC function is automatically set to OFF for the timer recording of a satellite programme.
The station name may not appear if the VCR does not receive station name information signals.
Recording TV programmes using the ShowView system (not available on SLV-SE610N/K)
58
Page 59

Recor ding TV programmes using the timer

DATE
CANCEL
SET::
SELECT :
CLEAR
MENUEXIT :
TIMER
SP / LP LIST
TIME PROG.
TODAY –– : –– ––: –– –
SP
FRI28 .9
SET :
SELECT :
OK
MENUEXIT :
TIMER METHOD
STANDARD SHOWVIEW
DATE
CANCEL
SET::
SELECT :
CLEAR
MENUEXIT :
TIMER
SP / LP LIST
TIME PROG.
TODAY –– : –– ––: –– –
SP VPS / PDC OFF
FRI28 .9
You can preset a total of eight programmes, including settings made with other timer methods.
Before you start
Check that the VCR clock is set to the correct time and date.
Insert a tape with its safety tab in place. Mak e sure the tape is longer than the to tal re c ordin g
time.
To record from a decoder, turn it on.
Turn on your TV and set it to the video channel.
Set TIMER OPTIONS to STANDARD or VARIABLE in the OPTIONS-2 menu (see page
85).*
Refer to Index to parts and controls for button locations.
TIMER
1
Press TIMER. For SLV-SE610N/K:
The TIMER menu appears on the
PLAY
TV screen.
OK
For SLV-SE710N/K, SX710N/K, and SE810N/K:
When you set TIMER OPTIONS to VARIABLE: The TIMER METHOD menu appears on the TV screen. Press
M/m
to select STANDARD, then
press OK.
Basic Operations
When you set TIMER OPTIONS to STANDARD: The TIMER menu appears on the TV screen.
continued
Recording TV programmes using the timer
59
Page 60
2
DATE
CANCEL
SET::
SELECT :
CLEAR
MENUEXIT :
TIMER
SP / LP LIST
TIME PROG.
TODAY 519 :00 20: 00 3
SP VPS / PDC OFF
FRI28 .9
PLAY
OK
INPUT SELECT
Set the date, start and stop times, programme position or station name*, tape speed, and VPS/PDC function*:
1
Press , to highlight each item in turn.
2
Press M/m to set each item.
To correct a setting, press < to return to that setting and reset.
To record the same programme every day or the same day every
week, see Daily/weekly recording on page 60.
To use the VPS/PDC function*, set VPS/PDC to ON. For details
about the VPS/PDC function, see T imer recording with VPS/ PDC signals on page 57.
To record from a decoder or other source connected to one or
more of the LINE inputs, press INPUT SELECT to display the connected line in the “PROG. position.
3
4
60
Recording TV programmes using the timer
MENU
Press MENU to exit the menu.
Press ?/1 to turn off the VCR. The indicator appears in the display windo w and the VCR stands
by for recording. To record from a decoder or other source, leave the connected
equipment switched on.
To stop recording
To stop the VCR while recording, press x STOP.
Daily/weekly recording
In step 2 above, press m to select the recording pattern. Each time you press
m
, the indication changes as shown below. Press M to change the indication
in reverse order.
TODAY t SUN-SAT (Sunday to Saturday) t MON-SAT (Monday to
Saturday) t MON-FRI (Monday to Friday) t SAT (every Saturday) .....
t MON (every Monday) t SUN (every Sunday) t 1 month later t (dates count down) t TOMORROW t TODAY
Page 61
To record satellite broadcasts
If you connect a satellite tuner and the VCR, you can record satellite programmes.
Turn on the satellite tuner.
1
On the satellite tuner, select the satellite programme for which you want
2
to make a timer setting. Follow steps 1 through 4 above.
3
Keep the satellite tuner turned on until the VCR finishes recording the
4
satellite programme for which you have made a timer setting.
To use the VCR after setting the timer
To use the VCR before a recording begins, just press ?/1. The indicator turns off and the VCR switches on. Remember to press ?/1 to reset the VCR to recording standby after using the VCR.
You can also do the following tasks while the VCR is reco rdin g:
Reset the counter (page 44).
Display tape information on the TV screen (page 47).
Check the timer settings (page 68).
Watch another TV programme (page 47).
Tips
To set the programme position, you can also use the PROG +/– or programme number buttons.
To set the programme position with a two digit number, press - (tens digit) button followed by the programme number buttons.
To set the line input video source, you can also use the PROG +/ buttons.
To set the tape speed, you can also use the SP/LP button.
When you ar e recording a programme in the SP mode and the remaining tape
becomes shorter than the recording time, the tape speed is automatically changed to the LP mode. Note that some interference will appear on the picture at the po int the tape speed is changed. If you want to keep the same tape speed, set AUTO LONG PLAY to OFF in the OPTIONS-1 menu (page 85).
Even if you set TIMER OPTIONS* to SHO WVIEW in t he OPTIONS-2 me nu, you can set the timer manually. Press MENU to select TIMER, then go to step 2.
To check, change, or cancel th e pr ogramme setting, press </, to choose LIST, then press OK in step 2. For details, see step 3 in “Checking/changing/cancelling timer settings (page 68).
Basic Operations
continued
Recording TV programmes using the timer
61
Page 62
Notes
When setting the timer with VPS/PDC signals, enter the start and stop times
exactly as indicated in the TV programme guide. Otherwise, the VPS/PDC function* won’t work.
If the VPS/PDC signal is too weak or the broadcasting station failed to transmit
VPS/PDC signals, the VCR will start recording at the set time without using the VPS/PDC function*.
The indicator flashes in the display wind ow when you press ?/1 with no tape
inserted.
The VPS/PDC function* is automatically set to OFF for the timer recording of a
satellite programme.
The station name* may not appear if the VCR does not receive station name
information signals.
* not available on SLV-SE610N/K
Recording TV programmes using the timer
62
Page 63
Additional Operations

Playing/searching at various speeds

Before you start
Refer to Index to parts and controls for button locations.
Playback optio ns Operation
Vie w the picture during fast-forward or rewind
Play at high speed During playback, press M FF or m REW on the remote
Play at twice the normal speed
Play in slow motion During playback, press ySLOW. Play frame by frame During pause, press M FF or m REW on the remote
Rewind and start play During stop, press H(play) on the VCR while holding down
During fast-forward, hold down M FF/M. During rewind, hold down m REW/m.
commander.
During playback, hold down M FF/M or m REW/m. When you release the button, normal playback resumes.
During playback, press ×2.
commander. Hold down M FF or m REW to play one frame each second.
m
on the VCR.
To resume normal playback
Press H PLAY.

Using the shuttle ring (SLV-SE810N/K only)

Shuttle ring
JOG
With the shuttle ring, you can operate a variety of playback options. There are two ways for using the shuttle ring, normal mode and jog mode.
Additional Operations
continued
Playing/searching at various speeds
63
Page 64
To use the shuttle ring in normal mode
Pause
Slow motion in reverse
Normal speed in reverse
Double speed in reverse
High speed in reverse
Slow motion
Double speed
High speed
Normal speed (Initial speed)
During playback or pause, turn the shuttle ring clockwise or anticlockwise. Each change in the shuttle ring position changes the playback mode in the following way.
To use the shuttle ring in jog mode
Use this mode for frame-by-frame playback. Press JOG to enter the jog mode. The J OG button lights up. If you change to
the jog mode during any playback mode, playback pauses so you can see a still picture. Each change in the shuttle ring position shifts the picture one frame. To shift frames in reverse, turn the shuttle ring anticlockwise. The frame shift speed depends on the speed you turn the shuttle ring.
To resume normal mode, press JOG again. The JOG button turns off.
Tip
Adjust the picture using the PROGRAM +/ buttons on the VCRStreaks appear while playing in slow motion.Bands appear at the top o r bottom while pausing.The pict ure shakes while pausing. To set tracking to the centre position, press both buttons (+/) at the same time.
Notes
The soun d is muted during thes e operations.
In the LP mode, noise may appear or there may be no colour.
If the playback mode mark doesnt appear on the TV screen, press DISPL AY.
Playing/searching at various speeds
64
if:
Page 65

Setting the recording duratio n tim e

After you have started recording in the normal way, you can have the VCR stop recording automatically after a specified duration.
Before you start
Refer to Index to parts and controls for button locations.
1
2
To extend the duration
Press z REC repeatedly to set a new duration time.
To cancel the duration
Press z REC repeatedly until the indicator disappears and the VCR returns to the normal recording mode.
To stop recording
To stop the VCR while recording, press x STOP.
While recording, press z REC. The indicator appears in the display window.
Press z REC repeatedly to set the duration time. Each press advances the time in increments of 30 minutes.
0:30 1:00
The tape counter decreases minute by minute to 0:00, then the VCR stops recording and turns off automatically.
5:30 6:00
SP OPCVIDEO
Additional Operations
Normal recording
Note
You cannot display the current tape time in the display window when setting the recording duration time.
Setting the recording duration time
65
Page 66
Synchronized Recording
(not avail able on SLV-SE610N/K)
You can set the VCR to automatically record programmes from equipment such as a satellite tuner by connecting the equipment to the DECODER/ LINE-3 IN* equipment must have a timer function for this feature to work.
When the connected equipment turns on, the VCR also automatically turns on and starts recording a programme from DECODER/LINE-3 IN* DECODER/LINE-2 IN*

How to connect for Synchronized Recording

Connect the DECODER/LINE-3 IN*1 (or DECODER/LINE-2 IN*2) connector of the VCR to the TV Scart connect the LINE-1 (TV) connector to the TV.
1
(or DECODER/LINE-2 IN*2) connector. The connected
2
).
connector of the satellite tuner. Then
1
(or
DECODER/t LINE-3 IN* or DECODER/t LINE-2 IN*
i
LINE-1 (TV)
: Signal flow
Scart cable (not supplied)
1
2
Scart cable (not supplied)
Satellite tuner, etc.
TV Scart connector
Scart (EURO-AV)

Synchronized Recording (not available on SLV-SE610N/K)

66
Page 67

Recording prog rammes using the Synchronized Recording function

Before you start...
Insert a tape with its safety tab in place. Make sure the tape is longer than the total recording time.
Set DECODER/LINE3* LINE2*2) to LINE3*1 (or LINE2*2) in the OPTIONS-2 menu (see pa ge 85).
Refer to Index to parts and controls for button locations.
Press INPUT SELECT or PROG +/– to display “L3*1 (or L2*2) in the
1
display window. Set the timer on the connected equipment to the time of the programme
2
you want to record, then turn it off. Press SP/LP to select the tape speed.
3
Hold down SYNCHRO REC for more than two seconds.
4
The SYNCHRO indicator appears in the display window and the VCR stands by fo r recording.
The VCR automatically turns on and starts recording when it receives an input signal from the connected equipment.
The VCR automatically stops recording when the tape reaches the end or when the connected equipment stops transmitting an input signal.
1
(or DECODER/
SYNCHRO REC
Additional Operations
To cancel the Synchronized Recording function
Press SYNCHRO REC. The SYNCHRO indicator disappears.
To stop recording
Press x STOP while recording.
Notes
This function may not work with some types of satellite tuners.
Some TVs or other equipment with timer functions will automat ically turn of f if no
operation is performed within a certain amount of time. In this case, the Synchronized Recording also stops automatically.
When the conn ected equipment turns on while the SYNCHRO indicator is appeared, recording starts automatically.
If the settings for timer recording and Synchronized Recording overlap, the programme that starts first has priority and the second programme starts recording only after the first programme has finished.
The Auto Clock Set function does not work while the VCR stands by for Synchronized Recording.
1
*
SLV-S E 81 0N / K on ly
*2SLV-SE710N/K and SX710N/K only
Synchronized Recording (not available on SLV-SE610N/K)
67
Page 68
Checking /changing/cancelling timer
MENUEXIT :
TIMER LIST
CANCEL
SET::
SELECT :
OK
CLEAR
RETURN
20 :00 21: 00
DATE TIME PROG.
AAB LP
2 0:00 1:30
CDE LP
MON
14 :00 15: 00 LP
SUN 6:30 7:00
SP
––: –– – : –– – – . ––
FRI
.10
VPS PDC
VPS PDC
03.9 11
FGH
I
FRI28 . 9
19 :00 20: 00
3SPTODAY 5
JK
DATE
CANCEL
SET::
SELECT :
CLEAR
MENUEXIT :
TIMER
SP / LP LIST
TIME PROG.
2 CDE
LP VPS / PDC ON
FRI28 .9
10 :00 11: 30
.10
settings
Before you start
Turn on your TV and set it to the video channel.
Refer to Index to parts and cont r ols for button locations.
Press ?/1 to turn on the VCR.
1
Press MENU, then press M/m to highlight LISTS and press OK.
2
Press M/m to highlight TIMER LIST,
3
then press OK:
If you want to change or cancel a setting, go on to the next step.
If you do not need to change or cancel the settings, press MENU, then turn off the VCR to return to recording standby.
Press M/m to select the setting you want
4
to change or cancel, then press OK. The selected setting appears in the
TIMER menu.
To change the setting, press </, to highlight the item you want to
5
change, then press M/m to reset it.
To cancel the setting, press CLEAR.
Press MENU to exit the menu.
6
If any settings remain, turn off the VCR to return to recording standby.
68

Checking/changing/cancelling timer settings

Page 69
When the timer settings overlap
The programme that starts f irst has pri orit y and the second programm e starts recording only after the first programme has finished. If the programmes start at the same time, the programme listed first in the menu has priority.
Programme 1 Programme 2
will be cut off
Programme 1 Programme 2
about 20 seconds will be cut off
about 20 seconds
Tip
In step 6 above, you can chec k the TIMER LIST by selecting LIST and pressing OK. Press MENU to exit the TIMER LIST.
Additional Operations
Checking/changing/cancelling timer settings
69
Page 70

Recording stereo and bilingual programmes

In ZWEITON (German stereo) system

This VCR automatically receives and records stereo and bilingual programmes based on the ZWEITON system. When a stereo or bilingual programme is received, the STEREO indicator appears in the display window.
To select bilingual sound while recording
Press AUDIO MONITOR to select the sound you want.
To listen to On-screen display Display window
Main MAIN STEREO Sub SUB STEREO Main and sub MAIN/SUB STEREO

In NICAM system (SLV-SE610N, SE710N, SX710N, and SE810N only)

This VCR receives and records stereo and bilingual programmes based on the NICAM system (The NICAM indicator appears). When a stereo or bilingual programme is received, the STEREO indicator appears in the display window.
To record a NICAM programme, HIFI AUDIO in the OPTIONS-1 menu should be set to NICAM (initial setting). To check the menu setting, see page 85 for details.
To select the sound while recording
Press AUDIO MONITOR to select the sound you want.
Stereo programmes To listen to On-screen display Display window
Stereo STEREO STEREO Standard sound* N o indicator No indicator
* Usually the mixed sound of left and right channels (monaural)
Recording stereo and bilingual programmes
70
Page 71
Bilingual programmes To listen to On-screen display Display window
Main MAIN STEREO Sub SUB STEREO Main and sub MAIN/SUB STEREO Standard sound* No ind icator No indicator
* Usually the main sound (monaural)

Selecting the sound during playback

Press AUDIO MONITOR to select the sound you want.
To listen to On-screen display Display window
Stereo/main and sub (left and right channels)
Left channel/main LCH STEREO Right channel/sub RCH STEREO Standard sound N o indicator No indicator
STEREO STEREO

How sound is recorded on a video tape

The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the main track along with the picture. Monaur al sound is r ecorded o nto the normal audio track along the edge of the tape.
Additional Operations
Normal audio track (monaural)
Hi-fi audio track (main track)
Stereo
Usually mixed left/right channels
Stereo sound (left/right channels)
Bilingual
Usually main sound
Main (left channel) Sub (right channel)
continued
Recording stereo and bilingual programmes
71
Page 72
Notes
To listen to playback sounds in stereo, you must use the Scart or AUDIO OUT
connections.
When yo u play a tape recorded in monaural, the sound is heard in monaural
regardless of the AUDIO MONITOR setting.
If the AUDIO MONITOR button does not function, check that AUDIO MIX*
the OPTIONS-1 menu is set to OFF (see page 84).
1
If HIFI AUDIO*
is set to STANDARD, the standard sound will be recorded on both the hi-fi and normal audio tracks. Pressing AUDIO MONITOR will not change the sound.
1
SLV-SE610N, SE710N, SX 710N, and SE810N only
*
1
in
Recording stereo and bilingual programmes
72
Page 73
Searching using the Smart Search
SMART SEARCHSAVE :
14 :00 15: 00 FGH
0 20 : 00 21:00
AAB
29 .9
.9
6:30 7:00 IJK1.10
3
SET
SELECT
SMART SEARCH
::OK
19 :00 20: 00 328 .9 5
DATE TIME PROG.
30 MIN.BLANK TIME
18 0 MIN.
SMART SEARCH
NOW SEARCHING
18 0 MIN.
function
If you record multiple programmes on a tape, you can use the Smart Search function to see what has been recorded on your tape. You can see information such as date, time, and programme position of the programmes recorded. You can also start playback directly from the selected programme using the SMART SEARCH screen.
All programmes are listed on the screen, regardless of how the programme was recorded.
To store programme information, see Storing the programme information on page
75. If you eject the tape before storing the information, the information will be cleared.
Before you start
Turn on your TV and set it to the video channel.
Refer to Index to parts and controls for button locations.
After recording, press ?/1 to turn on the
1
VCR. Press SMART SEARCH.
2
Press M/m/</, to select the programme
3
you want to start viewing.
Additional Operations
Press OK.
4
The VCR starts searching, and playback starts automatically from the beginning of the selected programme.
To stop searching
Press x STOP.
To exit the SMART SEARCH screen
Press MENU.

Searching using the Smart Search function

continued
73
Page 74
To record in a blank space
SMART SEARCHSAVE :
14 :00 15: 00 FGH
0
29 .9
.93
SET
SELECT
SMART SEARCH
::OK
DATE TIME PROG.
30 MIN.BLANK TIME
20 :00 21: 00
AAB
6:30 7:00
1.10 IJK
18 0 MIN.
Blank space on the tape will appear as a blank row in the SMART SEARCH screen. Select the last blank row in step 3, then pres s OK. The VCR rewinds/fast-forwards the tape to the beginning of the blank space, then stops. Start recording. Note that “BLANK TIME and the remaining time indication only refers to the length of the last blank space.
Tips
You can store inform ation for up to 24 programmes on a single list.
While re cording, you can display the SMART SEARCH screen using the SMART
SEARCH button. If you decide to stop recording, pr ess MENU to make the SMART SEARCH screen disappear first. Then press xSTOP.
You can have the player recall the data of the last cassette u s ed t o record programmes even after you eject the tape (page 78).
Notes
You cannot use thi s function unless the clock is set.
Depending on the tape, the total or remaining time may not appear correctly.
If many short programmes are recorded on a tape, multiple programmes may be
included in a single bl ock. In th is case, only th e late st progra mme in formatio n will appear in the SMART SEARCH screen.
Blank time is measured from the end of the last recorded programme to the end of the tape. However, if you eject the tape and then make a new recording on the same tape, the original recorded programme(s) is displayed as a blank space.
The station name* may not appear if the VCR does not receive station name information signals.
If you star t recording a programme D from t he middle of a previously recorded programme “A and into another previously recorded programme B, the Smart Search information for the second programme “B,” which is recorded over, is deleted.
Originally recorded programmes
AB
C
Searching using the Smart Search function
74
Recording the programme “D” over the programme “A” and “B”
AD C
* not available on SLV-SE610N/K
Page 75
Storing, searching and deleti ng
SMART SEARCHEXIT :
SET
SELECT
SMART SEARCH -RECALL-
::OK
DATE TIME PROG.
RECALL 1 2 3 4
20 :00 21: 00 AAB30 .9
6:30 7:00
1.10
14 :00 15: 00
FGH29 .9
IJK
SMART SEARCHEXIT :
SET
SELECT
SMART SEARCH -RECALL-
::OK
DATE TIME PROG.
RECALL 1 2 3 4
NO DATA
programme information (S mart Search Plus)
You can store programme information, such as the recording date and time, and programme position, for a maximum of four tapes. You can select a programme and start playback, by recalling the information directly from the Smart Search Plus screen.

Storing the programme information

You can store programme information for a maxi mum of four tap es. Befor e recording a programme, select a memory bank number from the list on the SMART SEARCH screen.
The unit will not memorize the memory bank number for each cassette. Note the number you assigned to each cassette.
Before you start...
Turn on your TV and set it to the video channel.
Refer to Index to parts and controls for button locations.
Insert a cassette for recording.
1
The VCR automatically turns on. Press SMART SEARCH.
2
The SMAR T SEARCH -RECALL-screen appears.
RECALL is highlighted and the data for the last cassette used to record programmes appears.
Additional Operations
Press </, to select a memory bank
3
number. Note the memory bank number on the
cassette. To cancel the process, press SMART
SEARCH.
Press OK.
4
Start recording.
5
The information about the recorded programme will be stored on the selected memory number.

Storing, searching and deleting programme information (Smart Search Plus)

continued
75
Page 76
To assign a memory number after recording
SMART SEARCHSAVE :
14 :00 15: 00 FGH
0
29 .9
.93
SET
SELECT
SMART SEARCH
18 0 MIN.
:
:
OK
DATE TIME PROG.
30 MIN.BLANK TIME
20 :00 21: 00
AAB
6:30 7:00
1.10 IJK
SMART SEARCHEXIT :
20 :00 21: 00
AAB30 . 9
6:30 7:00
1.10
14 :00 15: 00
FGH29 .9
SET
SELECT
SMART SEARCH -SAVE-
::OK
DATE TIME PROG.
CANCEL 1 2 3 4
IJK
SMART SEARCHEXIT :
SET
SELECT
SMART SEARCH -SAVE-
::OK
DATE TIME PROG.
CANCEL 1 2 3 4
20 :00 21: 00 AAB30 .9
6:30 7:00
1.10
14 :00 15: 00
FGH29 .9
IJK
After recording a programme, you can store the programme information as a new memory before ejecting the cassette. However, you cannot add the memory on the existed memory bank number. To store the memory as additional, select the memory bank number before.
Press ?/1 to turn on the VCR.
1
Press SMART SEARCH.
2
Press SMART SEARCH again.
3
The SMART SEARCH -SAVE- screen appears.
Press </, to select a memory bank
4
number. Select the memory bank number with no
information or the memory bank number to be deleted.
To cancel the process, select CANCEL.
Storing, searching and deleting programme information (Smart Search Plus)
76
Press OK.
5
To exit the SMART SEARCH screen
Press SMART SEARCH.
Note
If you select a number that is already contains program mes, the old programme information is cleared and the new programme inform ation is stored.
Page 77
Searching f or pr ogramme inf ormation stored on t he memory bank
SMART SEARCHEXIT :
SET
SELECT
SMART SEARCH -RECALL-
::OK
DATE TIME PROG.
RECALL 1 2 3 4
21 :30 23: 004.10
0 18 : 00 19 : 00
CDE2.1
I
J
K
SMART SEARCHEXIT :
SET
SELECT
SMART SEARCH -RECALL-
::OK
DATE TIME PROG.
RECALL 1 2 3 4
20 :00 21: 00 AAB30 .9
6:30 7:00
1.10
14 :00 15: 00
FGH29 .9
IJK
ERASE :
CLEAR
SMART SEARCHEXIT :
14 :00 15: 00 FGH
0
29 .9
.93
SET
SELECT
SMART SEARCH
18 0 MIN.
:
:
OK
2
DATE TIME PROG.
30 MIN.BLANK TIME
20 :00 21: 00
AAB
6:30 7:00
1.10 IJK
number
You can start playback of the recorded programme after call the programme information from the four memory bank numbers.
Before you start...
Turn on your TV and set it to the video channel.
Insert the cassette for which you want to use the memory bank number.
1
The VCR automatically turns on. Press SMART SEARCH.
2
The SMART SEARCH -RECALL­screen appears.
Press </, to select the memory bank
3
number for the inserted cassette. The programme information contained in
the selected memory bank number appears.
When you selected wrong memory bank number, eject the cassette and repeat steps from step 1.
Press OK.
4
The selected memory bank number appears on the SMART SEARCH screen.
Memory bank number
Additional Operations
Press M/m/</, to select the programme you want to start viewing.
5
Press OK.
6
The VCR starts searching, and playback starts automatically from the beginning of the selected programme.
To stop searching
Press x STOP.
Storing, searching and deleting programme information (Smart Search Plus)
continued
77
Page 78
To exit the SMART SEARCH screen
SMART SEARCHEXIT :
SET
SELECT
SMART SEARCH -RECALL-
::OK
DATE TIME PROG.
RECALL 1 2 3 4
21 :30 23: 004.10
0 18 : 00 19 : 00
CDE2.1
I
J
K
SMART SEARCHEXIT :
SET
SELECT
SMART SEARCH -RECALL-
::OK
DATE TIME PROG.
RECALL 1 2 3 4
20 :00 21: 00 AAB30 .9
6:30 7:00
1.10
14 :00 15: 00
29 .9
IJK
ERASE :
CLEAR
FGH
Press SMART SEARCH.
Recalling the most recent programme information
Programme information that is not saved in one of the memory bank numbers is erased when the cassette is ejected. The RECALL memory bank will temporarily memorize the programme information of the last tape used for recording in case that it is accidentally ejected.
If you re-insert the cassette in step 1 that you accidentally ejected and then select RECALL in step 3, the data for the last tape used to record programmes appears. Press OK and the latest information will appear on the SMART SEARCH screen. You can then add new information to this programme list. For an explanation about viewing programme information without using one of the memory banks, see page 73.
If you want to erase the latest information in the RECALL memory bank, press the SMART SEARCH button instead of the OK button in step 3 and then close the SMART SEARCH screen. The new information will replace all of the current information in the RECALL memory bank.
Note
When you insert the cassette whose information does not exist on the memory bank number, you cannot search the recorded programm e.

Deleting the programme information

You can delete the programme information stored in a memory number.
Before you start...
Turn on your TV and the VCR.
Set the TV to the video channel.
Storing, searching and deleting programme information (Smart Search Plus)
78
Press SMART SEARCH.
1
The SMART SEARCH -RECALL­screen appears.
Press </, to select the memory bank
2
number to delete. The programme information on the
selected memory bank number appears. Check the information that you want to delete.
Page 79
Press CLEAR.
SMART SEARCHEXIT :
SET
SELECT
SMART SEARCH -RECALL-
::OK
DATE TIME
NO DATA
PROG.
RECALL 1 2 3 4
3
The programme information is deleted.
Press SMART SEARCH.
4
The SMART SEARCH screen disappears.
Note
You cannot use or return the deleted information.

About the Demonstration Mode

The Smart Search Plus function has a Demonstration Mode that allows the user, such as a salesperson, to automatically display the Smart Search Plus screens.
To activate the Demonstration Mode
While the VCR is turned on, press and hold the both x (stop) and A (eject) buttons on the VCR four kinds of Smart Search Plus screens will be displayed repeatedly . If you operate the VCR, the Demonstration Mode temporarily stops. After about five minutes, the demonstration will restart.
To cancel the Demonstration Mode
While the VCR is turned off, press and hold the both x (stop) and A (eject) buttons on the VCR Demonstration Mode if you turn the power off and unplug the mains lead.
for a few seconds. The demonstration will start and the
for a few seconds. You can also cancel the
Additional Operations
Storing, searching and deleting programme information (Smart Search Plus)
79
Page 80

Searching using the index function

SEARCH
INDEX
The VCR automatically marks the tape with an index signal at the point where each recording begins. Use these signals as references to find a specific recording.
Insert an indexed tape into the VCR.
1
Press ./> INDEX SEARCH.
2
To search ahead, press > INDEX SEARCH.
To search backwards, press . INDEX SEARCH.
The VCR starts searching, and playback starts automatically from that point.
To stop searching
Press x STOP.
Notes
No index signal will b e added when recording starts from recording pause. However, an index signal will be marked if you change the programme position during recording pause.
When you pr ess . INDEX SEARCH, if there is nothing recorded before the selected index signal, playback may not start exactly at the index signal.
80
Searching using the index function
Page 81

Adjusting the picture

TRACKING
Tracking meter
CONFIRM :
SELECT :
OK
MENUEXIT :
OPTIONS - 2
TIMER OPTIONS
DECODER / LINE3 POWER SAVE
TV DIRECT REC
VARIABLE
DECODER OFF
HIGH OFF
RR
NORMAL
RETURN

Adjusting the tracking

Although the VCR automatically adjusts the tracking when playing a tape (the indicator flashes in the display window, then turns off), distortion may occur if the recording is in poor condition. In this case, manually adjust the tracking.
During playback, press PROGRAM +/– on the VCR to display the tracking meter. The distortion should disap pear as you pres s one of the two button s (the indicator lights up). To resume automatic tracking adjustments, eject the tape and re-insert it.

About the Reality Regenerator (RR) function

The Reality Regenerator function automatically restores the picture to its original quality during playback.
To use the Reality Regenerator function
Press MENU, then select OPTIONS and press OK.
1
Press M/m to highlight OPTIONS-2, then press OK.
2
Press M/m to highlight RR, then press
3
OK.
Additional Operations
4 5
To turn it off, select OFF in step 4. The RR indicator turns off in the display window.
Press M/m to set RR to NORMAL or HIGH, then press OK. The RR indicator lights up in the display window.
Press MENU to return to the original screen.
continued
Adjusting the picture
81
Page 82

About the Optimum Picture Control (OPC) function

SET :
SELECT :
OK
MENUEXIT :
OPTIONS - 1
ON OFF OFF
OFF
NICAM E18 0
OPC EDIT AUDIO MIX HIFI AUDIO AUTO LONG PLAY TAPE LENGTH
RETURN
AUTO
COLOUR SYSTEM
The Optimum Picture Control (OPC) function automatically improves recording and playback quality by adjusting the VCR to the condition of the video heads and tape. To maintain better picture quality, we recommend that you set OPC to ON in the OPTIONS-1 m enu (the OPC indicator light s up in the display window). For details, see page 84.
OPC playback
The OPC function automatically wo rks on all types of tapes, incl uding rental tapes and tapes that were not recorded with OPC.
OPC recording
Whenever you insert a tape and start recording for the first time, the VCR adjusts to the tape using the OPC function (the OPC indicator flashes rapidly). This adjustment is retained until the tape is ejected.
To deactivate the OPC function
Set OPC to OFF in the OPTIONS-1 menu. The OPC indicator in the display window turns off.
Tip
To set tracking to the centre position, press the PROGRAM + and – button s on the VCR at the same time.
82
Notes
You can adjust the tracking for an NTSC-recorded tape but the tracking meter wont be displayed.
With the Auto Long Play function on, the OPC function will work only in SP mode. If the tape speed automatically switches from SP to LP, the OPC function turns off. If, however, the entire programme is recorded in LP mode, the OPC function will work.
There is a delay of about ten seconds before the VCR actually starts recording while the VCR analyses the tape. To a v oid the delay, first set the VCR to recording pause (the OPC indicator flashes slowly) and press zREC to have the VCR analyse the tape ( the OP C indic ator flas hes ra pidl y) a nd retu rn to rec ordin g pau se. After the OPC indicator s to ps f lashing, press XPAUSE to star t recording immediately. If you want to start recording quickly without using the OPC function, first set the VCR to recording pause (the OPC indicator flashes slowly) and press XPAUSE again to start recording.
Adjusting the picture
Page 83

Reducing the VCR’s power consumption

CONFIRM :
SELECT :
OK
MENUEXIT :
OPTIONS - 2
TIMER OPTIONS
DECODER / LINE3 POWER SAVE
DECODER
FULL TV DIRECT REC RR
PARTIAL
OFF
RETURN
You can turn off the indicators in the display window when the VCR is off (standby mode) to reduce the VCR’s power consumption.
Press MENU, then select OPTIONS and press OK.
1
Press M/m to highlight OPTIONS-2, then press OK.
2
Press M/m to select POWER SAVE, then
3
press OK.
Press M/m to highlight the option, then press OK.
4
For SLV-SE710N/K, SX710N/K, and SE810N/K:
FULL to redu ce the power consumption to a minimum.
PARTIAL to reduce the power consumption.
For SLV-SE610N/K:
ON to reduce the power consumption to a minimum. Press MENU to return to the original screen.
5
Additional Operations
To turn on the indicators in the display window
Set POWER SAVE to OFF in step 4.
Notes
When the VCR stands by for recording, the indicators in the display window remain lit even when POWER SAVE is set to FULL, PARTIAL, or ON.
If POWER SAVE is set to FULL*, you cannot watch or record programmes from your Canal Plus decoder, satellite, or digital tuner during standby mode (page 86).
* not available on SLV-SE610N/K
Reducing the VCRs power consumption
83
Page 84

Changing menu options

RETURN
SET :
SELECT :
OK
MENUEXIT :
OPTIONS
OPTIONS - 1 OPTIONS - 2
SET :
SELECT :
OK
MENUEXIT :
OPTIONS - 2
TIMER OPTIONS
DECODER / LINE3 POWER SAVE
TV DIRECT REC
VARIABLE
DECODER OFF
ON
RR
NORMAL
RETURN
Press MENU, then select OPTIONS and
1
press OK.
Press M/m to highlight OPTIONS-1 or OPTIONS-2, then press OK.
2
Press M/m to select the option, then press OK.
3
Press M/m to change the setting, then press OK.
4
Press MENU to return to the original screen.
5
Menu choices
Initial settings are indicated in bold print.
OPTIONS - 1
OPC EDIT AUDIO MIX HIFI AUDIO AUTO LONG PLAY TAPE LENGTH COLOUR SYSTEM
RETURN
SELECT : SET :
OK
ON OFF OFF NICAM OFF E AUTO
180
MENUEXIT :
84
OPTIONS-1
Menu option Set this option to
OPC ON to switch on the OPC (Optimum Picture Control)
EDIT ON to minimize picture deterioration when editing.
AUDIO MIX
Changing menu options
function and improve picture qua lit y.
OFF to switch off OPC.
OFF
to turn off EDIT.
ON to listen to the hi-fi and normal audio tracks at the same time. The AUDIO MONITOR button will not function.
OFF
to listen to the hi-fi and normal audio tracks separately. Select the sound using the AUDIO MONITOR button.
If you press ZEJECT, AUDIO MIX will be reset to OFF . For details, see page 72.
Page 85
Menu option Set this option to
HIFI AUDIO*
1
NICAM
to record NICAM broadcasts on the hi-fi audio
track.
STANDARD to record standard sound on the hi-fi audio track.
For details, see page 70.
AUT O LONG PLAY ON to change the timer recording tape speed
automatically to the LP mode when the remaining tape length becomes shorter than the recording time. Note that for AUTO LONG PLAY to work correctly, the TAPE LENGTH setting must be accurate.
OFF
to keep the set tape speed.
TAPE LENGTH
E180
to use an E-180 or shorter type tape.
E195 to use an E-195 type ta pe.
E240 to use an E-240 type ta pe.
E300 to use an E-300 type ta pe.
COLOUR SYSTEM
AUTO
to set the colour system automatically.
PAL to play back a tape recorded in the PAL colour system.
MESECAM to play back a tape recorded in the MESECAM colour system.
If you press Z EJECT or turn the VCR off, COLOUR SYSTEM will be reset to AUTO.
OPTIONS-2
Menu option Set this option to
DECODER/
2
LINE2*
DECODER/
3
LINE3*
TIMER OPTIONS*
DECODER
to use the DECODER/LINE-2 IN
connector as the Canal Plus decoder connector.
LINE2 to use the DE CODER/LI NE-2 IN connector as the line input connector.
DECODER
to use the DECODER/LINE-3 IN
connector as the Canal Plus decoder connector.
LINE3 to use the DE CODER/LI NE-3 IN connector as the line input connector.
4
VARIABLE
to display the TIMER METHOD menu for
selecting STANDARD or SHOWVIEW when pressing the
TIMER button.
STAND ARD to display the TIMER menu when pressing the TIMER button.
SHOWVIEW to display the SHOWVIEW menu when pressing the TIMER button.
For details, see page 55 and 59.
Additional Operations
continued
Changing menu options
85
Page 86
Menu option Set this option to
4
POWER SAVE*
FULL to turn off the indicators in the display window
during standby mode to r educe the VCRs power consumption t o a minimu m. F or using th e Line Thro ugh function (page 18) or the decoder (page 39), select PARTIAL or OFF.
PARTIAL to turn off the indicators in the display
window to conserve the VCRs power.
OFF
to turn on the indicators in the display window
while the VCR is standing by.
5
POWER SAVE*
ON to turn off the indicators in the display window
during standby mode to r educe the VCRs power consumption to a minimum.
OFF
to turn on the indicators in the display window
while the VCR is standing by.
4
TV DIRECT REC*
•ON to activate the TV Direct Rec function.
OFF to deactivate it.
RR
for normal everyday use.
NORMAL
HIGH for well-used video tapes such as rente d tapes.
Select this option when NORMAL does no t im prove the picture quality.
OFF to switch off the Reality Regenerator function.
Notes
When the VCR stands by for recordin g, the indicators in the display window remain lit even when POWER SAVE is set to FULL, PARTIAL or ON.
With the EDIT option ON, the OPC function does not work.
*1SLV-SE610N, SE710N, SX 710N, and SE810N only
2
*
SLV-SE710N/K and SX710N/K only
3
*
SLV-SE810N/K only
4
*
not available on SLV-SE610N/K
5
*
SLV-SE610N/K only
Changing menu options
86
Page 87
Editing

Connecting to a VCR or stereo system

How to connect to record on this VCR

Connect the line outputs of the other VCR to the LINE IN connector or jacks of this VCR. Refer to the examples A through C and choose the connection that best suits your VCR.
Example A
Example B
Yo ur VC R (Recorder)
i LINE-1 (TV)
VMC-2121HG Scart cable (not supplied)
: Signal flow
Your VCR (Recorder)
tttt LINE-2 L o (open cover to connect)
o R
o o
TV
Editing
Other VCR (Player)
Scart (EURO-AV)
TV
LINE OUT
VMC-820HG audio/video cable (not supplied)
: Signal flow
Other VCR (Player)
continued
Connecting to a VCR or stereo system
87
Page 88
Example C
Your VCR (Recorder)
: Signal flow
DECODER/ t LINE-3 IN* or DECODER/ t LINE-2 IN*
VMC-2121HG Scart cable (not supplied)
1
Other VCR (Player)
2
TV
Scart (EURO-AV)

How to connect to a stereo system (SLV-SE810N/K only)

Connect the t LINE-2 L o R jacks on this VCR to the audio output jacks on the stereo system, using the RK-C510HG audio cable (not supplied).
Notes
Make sure you connect the plugs to jacks of the same col our.*
If the other VCR is a monaural type, leave the red plugs unconnected.
If you connect this VCR to both the LINE IN and LINE OUT jacks of the other
VCR, select the input correctly to prevent a humming noise.
If the other VCR does not have a Scart (EURO-AV) connector, use the VMC­2106HG cable instead and connect the cable to the line out jacks of the other VCR.
When you connect another VCR to the DECODER/LINE-3 IN* LINE-2 IN* LINE3*
1
SLV-SE810N/K only
*
2
*
SLV-SE710N/K and SX710N/K only
2
) connector, set DECODER/LINE3*1 (or DECODER/LINE2*2) to
1
(or LINE2*2) in the OPTIONS-2 menu.
1
1
(or DECODER/
Connecting to a VCR or stereo system
88
Page 89

Basic editing

(when recording on this VCR)

Before you start editing
Turn on your TV and set it to the video channel.
Press INPUT SELECT to display the connected line in the display window.
Press SP/LP to select the tape speed, SP or LP.
On this VCR, set EDIT to ON in the
OPTIONS-1 menu. If the other VCR has a similar function, turn it on as well.
Insert a source tape with its safety tab removed into the other (playback)
1
VCR. Search for the point to start playback and set it to playback pause. Insert a tape with its safety tab in place into this (recording) VCR.
2
Search for the point to start recording and press X (pause). Press z REC on this VCR to set it to recording pause.
3
To start editing, press the X (pause) buttons on both VCRs at the same
4
time.
To stop editing
Press the x (stop) buttons on both VCRs.
Tip
To cut out unwanted scenes while editing, press X (pause) on this VCR when an unwanted scene begins. When it ends, press X (pause) again to resume recording.
Note
If you start editing following the procedure above, the VCR wont start recording with the OPC function. To record a tape with the OPC function, press zREC again during recording pause i n step 3 so the VCR analyses the tape. Then, pre ss
X
(pause) after
(pause) before
the OPC indicator stops flashing to start recording. If you press X
the OPC indicator stops flashing, the OPC function is cancelled.
REC
zzzz
X
Editing
Basic editing
89
Page 90
Audio dubbing
(SLV-SE810N/K only)
This feature lets you record over the normal audio track. The monaural sound previously recorded is replaced while the original hi-fi sound remains unchanged. Use this feature to add commentary to a tape that you have recorded with a camcorder.
Before you start...
Open the t LINE-2 L o R jacks cover on the front panel and connect a playback source.
Turn on the TV and set it to the video channel.
Insert a source tape into your stereo system (or the playback VCR).
1
Search for the point to start playback and set it to playback pause. Insert a prerecorded tape with its safety tab in place into this (recording)
2
VCR. Search for the start of the section to be replaced and press X (pause).
The VCR enters pause mode. Press AUDIO DUB.
3
The programme position changes to “L2,” and the indicator appears in the display window.
To start editing, press the X (pause) buttons on this VCR and the stereo
4
system (or other VCR) at the same time. After you use this feature, the audio in playback mode is automatically
set to monaural.
tttt LINE-2 L oooo R
AUDIO DUB
X
To stop editing
Press x (stop) on this VCR and the stereo system (or other VCR).
To listen to both the hi-fi and normal audio
Set AUDIO MIX to ON in the OPTIONS-1 menu (page 84). Use this feature to listen to dubbed audio over the original hi-fi audio. When AUDIO MIX is set to ON, the AUDIO MONITOR button does not function.
Remember to reset AUDIO MIX to OFF after playing the tape.
Note
If you eject the tape or turn the VCR off, AUDIO MIX is automatically set to OFF.

Audio dubbing (SLV-SE810N/K only)

90
Page 91
Additional Information

Troubleshooting

If you have any questions or problems not covered below, please consult your nearest Sony service facility.
Symptom Remedy
The ?/1 (on/standby) switch does not function.
The power is turned on but the VCR does not operate.
Power
The VCR is plugged in but the displa y wind ow remains dark.
The clock has stopp ed and “–:– –” appears in the display window.
Clock
The playback picture does not appear on the TV screen.
The picture is not clear. If your TV is connected to the VCR with both Scart and
Playback
The picture has no colour.
Connect the mains lead to the mains securely.
Moisture condensation has occurred. Turn the power off,
unplug the mains lead and leave the VCR to dry for over three hours.
Set POWER SAVE in the OPTIONS-2 menu to OFF (see page 86).
The clock stops if the VCR is disconnected from the mains for more than one hour. Reset the clock (and timer).
Make sure the TV is set to the video channel. If you are using a monitor, set it to video input.
If the VCR is connected to the TV with the Scart cable, make sure the VIDEO indicator is lit in the display window. Use the t TV/VIDEO button on the remote co mmander to ligh t up the VIDEO indicator.
aerial cables, make sure the RF channel is set to OFF (see page 21).
Existing broadcasts may interfere with the VCR. Reset the RF channel output of yo ur VC R .
Adjust the tracking with the PROGRAM +/– buttons on the VCR.
The video head s are di rty (see the last page of Troubleshooting). Clean the video heads using the Sony T-25CLD, E-25CLDR, or T-25CLW video head cleaning cassette. If these cleaning cassettes are not available in your area, have the heads cleaned at your nearest Sony service facility (a standard service charge will be required). Do not use a commercially available liquid type cleaning casset te other than Sonys, as it may damage the video heads.
The video heads may have to be replaced. Consult your local Sony service facility for more information.
The COLOUR SYSTEM option in the OPTIONS-1 menu is set to the wrong position. Set the option to conform to the system that the tape was recorded in.
Additional Information
continued
Troubleshooting
91
Page 92
Symptom Remedy
The picture rolls
Adjust the vertical hold control on the TV or monitor.
vertically during picture search.
The picture has no sound.
The tape is defective.
If you made A/V connections, check the audio cable
connection.
The sound is unstable or has an echo.
Playback
The sound from a tape recorded with the VCR is not in stereo or the STEREO indicator in
When you play a tape with the same sound recorded on both
the hi-fi and normal audio tracks, make sure AUDIO MIX in the OPTIONS-1 menu is set to OFF.
Adjust the tracking.
The video heads are dirty. Clean the video heads using the
Sony T-25CLD, E-25CLDR, or T-25CLW video head cleaning cassette as explained above.
the display window is flashing.
No TV programme appears on the TV screen.
Make sure the TV is set to the video channel. If you are
using a monitor, set it to video input.
If your TV is connected to the VCR with both Scart and
aerial cables, make sure the RF channel is set to OF F (see page 21).
Existing broadcasts may interfere with the VCR. Reset the
RF channel output of your V CR .
Select the correct source with the INPUT SELECT button.
Select a programme position when recording TV programmes; select a line input when recording from other equipment.
TV reception is poor. Make sure the aeria l cable is connected securely.
Adjust the TV aerial.
Recording
Make sure the TV system is correctly set for your TV.
Make sure SYSTEM (B/G or D/K) in the TUNER menu is
set to the same system in your local area .
The tape starts playing as soon as it is inserted.
The tape is ejected when you press
z
REC.
Nothing happens when
The safety tab has been removed. To record on this tape,
cover the tab hole (see page 47).
The safety tab has been removed. To record on this tape,
cover the tab hole (see page 47).
Make sure the tape is not at its end.
you press zREC.
Troubleshooting
92
Page 93
Symptom Remedy
The timer does not operate.
Check that the clock is set.
Make sure a tape has been inserted.
Check that the safety tab has not been removed.
Make sure the tape is not at its end.
Make sure a programme has been set for timer recording.
Make sure your timer settings are past the current time.
Check that the decoder is turned on.
Check that the satellite tuner is turned on.
The clock stops if the VCR is disconnected from the mains
for more than one hour. Reset the clock and timer.
Turn the power off and unplug the mains lead.
The SHOWVIEW menu or the TIMER
Timer recording
menu does not appear. The VPS/PDC function
does not operate properly.
Check that TIMER OPTIONS in the OPTIONS-2 menu is set correctly (see page 85).
Check that the clock and the date are set correctly.
Check that th e VPS/PDC time you set is the correct one
(there might be a mistake in the TV programme guide). If the broadcast you wanted to record did not send the good VPS/PDC information, the VCR will not start recording.
If the reception is poor, the VPS/PDC signal might be altered and the VCR might not start recording.
The SYNCHRO REC button turns off while
The tape has reached its end. Insert a new tape and press SYNCHRO REC again.
recording or does not go back to recording standby mode.
The Synchronized Recording function does not work.
The connect ed equipment was not turned off. Turn off the connected equipment and press SYNCHRO REC again.
There was a power failure. Press SYNCHRO REC again.
The programme recorded with the
Synchronized Recording
Synchronized Recording function is incomplete.
If the settings for timer recordings and Synchronized Recording overlap, the programme that starts first has priority and the second programme starts recording only after the first programme has finished.
There was a power failure. Press SYNCHRO REC again.
Additional Information
continued
Troubleshooting
93
Page 94
Symptom Remedy
You cannot set channels as PAY-TV/
Check that DECODER/LINE3 (or DECODER/LINE2) in
the OPTIONS-2 menu is set to DECODER (see page 85). Canal Plus in the TUNER menu.
You cannot watch Canal Plus pr ogrammes when the VCR is in standby mode.
Check that DECODER/LINE3 (or DECODER/LINE2) in the OPTIONS-2 menu is set to DECODER (see page 85).
Make sure the Canal Plu s Scart cable is plugged securely.
Check that POWER SA VE in the OPTIONS-2 menu is set to
PARTIAL or OFF (see page 86).
A Canal Plus
PAY-TV/Canal Plus
programme is always recorded scrambled.
Make sure the Canal Plu s Scart cable is plugged securely.
Check that DECODER/LINE3 (or DECODER/LINE2) in
the OPTIONS-2 menu is set to DECODER (see page 85).
Check that this channel is set as PAY-TV/Canal Plus in the TUNER menu (see page 39).
A tape cannot be
Check that a tape isnt already in the tape compartment.
inserted. The remote commander
does not function.
Make sure you are pointi ng the remote commander at the remote sensor on the VCR .
Replace all the batteries in the remote commander with new ones if they are weak.
Make sure the correctly.
The selected input line connector number does not appear in the
Check that DECODER/LINE3 (or DECODER/LINE2) in the OPTIONS-2 menu is set to LINE3 (or LINE2) (see page
85).
display window. The SMARTLINK
function does not work.
Check that your TV complies with SMARTLINK, MEGALOGIC, EASYLINK, Q-Link, EURO VIEW LINK, or T-V LINK.
Others
Make sure you use th e Scart cable to connect the VCR and your TV.
Make sure the Scart cabl e is connected securely.
The tracking meter does not appear on the TV screen.
The recording condition of the tape is very poor and tracking cannot be adjusted.
The tracking meter does not appear when playi ng back an NTSC-recorded tape.
You cannot control other TVs.
The display window becomes dim.
The VCR needs to be cleaned.
Set your TVs code number. The code number may change when you replace the batteries of t he remote commander.
The display window automatically becomes dim when the VCR is in standby or timer recording mode.
Clean the cabinet, panel and co ntrols w ith a dry, soft cloth, or a soft cloth slightly moistened with a mild detergent sol ution. Do not use any type of solvent, such as alcohol or benzine.
[TV]
[VIDEO]
/
remote control switch is set
Troubleshooting
94
Page 95
Symptoms caused by contaminated video heads
)
Normal picture Rough picture
Unclear picture • No picture (or
black & white screen appears
initial contamination
terminal
Additional Information
Troubleshooting
95
Page 96

Specifications

System
Channel coverage
PAL (B/G, D/K) VHF E2–E12, R1–R12 UHF E21–E69, R21–R69 CATV S1–S41, S01–S05
RF output signal
UHF channels 21–69
Aerial out
75-ohm asymmetrical aerial socket
Tape speed
SP: PAL/MESECAM
23.39 mm/s (recording/playback) NTSC
33.35 mm/s (playback only)
LP: PAL/MESECAM
11.70 mm/s (recording/playback) NTSC
16.67 mm/s (playback only)
EP: NTSC
11.12 mm/s (playback only)
Maximum recording/ playback time
10 hrs. in LP mode (with E300 tape)
Fast-forward and rewind time
Approx. 1 min. (with E18 0 ta pe)
Inputs and outputs
i
LINE-1 (TV) 21-pin Video input: pin 20 Audio input: pins 2 and 6 Video output: pin 19 Audio output: pins 1 and 3
DECODER/t LINE-2 IN (SLV-SE710N/K, SX710N/K)
21-pin Video input: pin 20 Audio input: pins 2 and 6
DECODER/t LINE-3 IN (SLV-SE810N/K)
21-pin Video input: pin 20 Audio input: pins 2 and 6
t
LINE-2 L o R (SLV-SE810N/K)
VIDEO IN, phono jack (1) Input signal: 1 Vp- p, 75 ohms, unbalanced, sync negative AUDIO IN, phono jack (2) Input level: 327 mVrm s Input impedance: more than 47 kilohms
R/D L/G (SLV-SE710N/K, SX710N/K,
SE810N/K)
Phono jack (2) Rated output level: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms
Specifications
96
Page 97
General
Power requirements
220 – 240 V AC, 50 Hz
Power consumption
20 W
1.2 W (POWER SAVE is set to FULL/ ON, minimum)
Operating temperature
°°°°
C to 40
°°°°
C
5
Storage temperature
–20°C to 60°C
Dimensions includi ng projecting parts and controls
Approx. 430 × 98 × 283 mm (w/h/d) (SLV-SE610N/K, SE710N/K, SX710N/K) Approx. 430 × 98 × 28 9 mm (w/h /d) (SLV-SE810N/K)
Mass
Approx. 4.1 kg
Supplied accessories
Remote commander (1) R6 (size AA) batteries (2) Aerial cable (1)
Additional Information
Design and specifications are subject to change without notice .
Specifications
97
Page 98

Index

A
Adjusting
Aerial hookup AFT (Auto Fine Tuning) Audio dubbing Audio track Auto Clock Set Auto Long Play Auto Set Up
picture tracking
33,
71
81
22
81
15
90
27
85
C
Canal Plus 39 CAT V (Cable Television) 41 Changing the progra m me positions Changing the station nam e s Cleaning the video heads Clock setting Colour system
Connecting
Counter
34
25
compatible colour systems 2 setting
44
the VCR and your TV 16 to a satellit e tuner to a stereo system to a TV with a Scart (EURO-AV) connector
44
18 18
D
Demonstration 54, 79 Dial Timer Disabling the program m e positions Dubbing.
35
See
50
Editing
E
Editing 87 EP mode
45
H
Hi-fi audio track 71
33
30,
91
15,
I
Index search 80
L
Language selecting 29 LP mode
46
M
Monaural 70 Monitoring
during playback during recording
71
70
N
NICAM broadcasts 70 Normal audio track
O
37
OPC (Optimum Picture Control) Optional setting
82
71
84
P
PAY-TV 39 PDC (Programme Delivery
57
16
Control) Picture adjustment. Adjusting Playback
Power save Presetting chann els
44 at various speeds frame-by-frame selecting the sound slow motion
83,
See
63
63
71
63
86
30
R
Reality Re generator 81 Recording
46 bilingual programmes duration time saving stereo programmes timer setting using the Dial Ti mer using the ShowView system
65
47
59
55
70
70
50
what you are watching on
48
the TV while watching another programme
RF channel
19,
21
47
S
Safety tab 47 Scart connect ion Searching
at various speeds using the index func tion using the Smart Search function
ShowView
recording Smart Search SMARTLINK
Automatic Power Off
One Touch Menu
One Touch Play
One Touch Timer
Preset Download
TV Direct Rec SP mode
70
Stereo Synchronized Recording
16
63
73
55
73
17
17,
17
17
17,
46
T
Timer setting 59
cancelling
changing
checking
daily/wee kly recording
60
using the Dial Timer
using the ShowView
system Tracking adjustment. Adjusting
68 68 68
55
See
V
VPS (Video Programme
57
System)
Z
ZWEITON broadcasts 70
48
80
17
45
66
57,
50
98
Index
Page 99
Page 100
Quick Start Guide
T
Connecting the VCR
1
1
AERIAL IN
AERIAL OU
4
23
: Signal flowyLINE-1 (TV)
1
... Conne ct the aerial to AERIAL IN of the VCR.
2
...Connect AERIAL OUT th e a er ia l in p ut of your
TV using the supp l ied aerial cable.
3
...For better picture and sound, connect LINE-1
(TV) to your TV us i ng a Sc art cabl e i f your TV has a Scart (EURO-AV) connector.
4
...C onnect the mains lead to the mains.
Tuning your TV to the VCR
2
I
RF CHANNEL
1
/
6
... Tune the TV to the same channel shown in
the VCR display window so that SONY VIDEO CASSETTE RECORDER appears clearly on the TV screen. Refer to your TV’s instruction manual for tuning instructions.
7
... Press RF CHANNEL.
B
If your TV has a Scart (EURO-AV) connector
1
....Press I/1 (on/standby) to turn on the VCR.
2
... Press RF CHANNEL on the VCR lightly.
3
... Press PROGRAM +/– to set the RF channel
to OFF.
4
... Press RF CHANNEL.
Using the Auto Set Up function
3
AUTO SET UP
PROGRAM +/–
You can set the language for the on-screen display and channels.
1
....Hold down AUTO SET UP on the VCR for more
than three seconds.
2
...Press PROGRAM +/– to select the abbreviation
of your country from the Country abbreviat ion table.
3
... Press AUTO SET UP lightly.
PROGRAM +/–
A
If your TV does not have a Scart (EUR O -A V ) connector
1
....Press I/1 (on/standby) to turn on the VCR.
2
...P ress RF CHANNEL on the VCR lightly.
3
...Turn on your TV and select a programme
position for the VCR picture.
4
...P ress RF CHANNEL.
5
...Press PROGRAM +/– (repeatedly) to select
the appropriat e TV system for y our area (G or K).
Sony Corporation
When all the receiv able cha nnels ar e preset , SET UP disappears from the display window. You can rearrange the programme position to your favourite order (see Changing/disabling programme positions).
Now you can operate your VCR.
Loading...