4-075-499-22
Trinitron® Color TV
Operating Instructions
KV-27FS12
KV-27FS16
KV-27FV16
KV-32FS12
KV-32FS16
© 2000 by Sony Corporation
WARNING
To reduce the risk of fire or electric shock, do not expose the TV to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE DE CHOC ELECTRIQUE,
NE PAS OUVRIR
PRECAUCION
RIESGO DE CHOQUE ELECTRICO
NO ABRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Note to the CATV Installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.
SAFETY PRECAUTIONS
Operate the TV only on 120 V AC.
One blade of the power plug is wider than the other for safety purposes and will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer.
If any liquid or solid object falls into the TV, unplug it and have it checked by qualified personnel before operating it further.
CAUTION
When using TV games, computers, and similar products with your TV, keep the brightness and contrast functions at low settings. If a fixed (non-moving) pattern is left on the screen for long periods of time at a high brightness or contrast setting, the image can be permanently imprinted onto the screen. Continuously watching the same channel can cause the imprint of station logos onto the TV screen. These types of imprints are not covered by your warranty because they are the results of misuse.
To reduce the risk of electric shock, do not use this polarized plug with an extension cord, receptacle, or other outlet unless the blades can be fully inserted to prevent blade exposure.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
NOTIFICATION
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference with radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antennas.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Protecting the TV
To prevent internal heat build-up, do not block the ventilation openings.
Do not install the TV in a hot or humid place, or in a place subject to excessive dust or mechanical vibration.
Note on Caption Vision
This television receiver provides display of television closed captioning in accordance with § 15.119 of the FCC rules.
Use of this television for other than private viewing of programs broadcast on UHF or VHF or transmitted by cable companies for the use of the general public may require authorization from the broadcaster-cable company and/or program owner.
Owner’s Record
The model and serial numbers are located on the front cover of this manual and the rear of your TV.
Trademarks and Copyrights
ENERGY STAR® is a registered mark.
As an ENERGY STAR® Partner, Sony has determined that this product or product models meet the ENERGY STAR® guidelines for energy efficiency.
Licensed by BBE Sound, Inc. under USP 4638258.4482866. BBE and BBE symbol are trademarks of BBE Sound, Inc.
(
)® SRS (SOUND RETRIEVAL SYSTEM) (KV-27FV16 only)
The (
) SRS (SOUND RETRIEVAL SYSTEM) is manufactured by Sony Corporation under license from SRS Labs, Inc. It is covered by U.S. Patent No. 4,748,669. Other U.S. and foreing patents pending.
The word ‘SRS’ and the SRS symbol (
) are registered trademark of SRS Labs, Inc.
Important Safeguards
For your protection, please read these instructions completely, and keep this manual for future reference. Carefully observe and comply with all warnings, cautions and instructions placed on the set, or described in the operating instructions or service manual.
WARNING
To guard against injury, the following basic safety precautions should be observed in the installation, use, and servicing of the set.
Use
Power Sources
This set should be operated only from the type of power source indicated on the serial/model plate. If you are not sure of the type of electrical power supplied to your home, consult your dealer or local power company. For those sets designed to operate from battery power, refer to the operating instructions.
For the set with a polarized AC power cord plug
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the polarized plug by forcing it in.
Grounding or Polarization
This set is equipped with a polarized AC power cord plug (a plug having one blade wider than the other), or with a three-wire grounding type plug (a plug having a third pin for grounding).
Follow the instructions below:
Alternate Warning
For the set with a three-wire grounding type AC plug
This plug will only fit into a groundingtype power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to have a suitable outlet installed. Do not defeat the safety purpose of the grounding plug.
Overloading
Do not overload wall outlets, extension cords or convenience receptacles beyond their capacity, since this can result in fire or electric shock. Always turn the set off when it is not to be used. When the set is left unattended and unused for long periods of time, unplug it from the wall outlet as a precaution against the possibility of an internal malfunction that could create a fire hazard.
Do not disconnect the antenna or the power cord during a heavy storm. Lightning may strike while you are holding the cable or cord, causing serious injury. Turn off your TV and wait for the weather to improve.
Do not place any objects, especially heavy objects, on top of the set. The object may fall from the set, causing injury.
Cleaning
Unplug the set from the wall outlet before cleaning or polishing it. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the set.
If a snapping or popping sound from a TV set is continuous or frequent while the TV is operating, unplug the TV and consult your dealer or service technician. It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being turned on or off.
Object and Liquid Entry
Never push objects of any kind into the set through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the set.
Installation
Always use two or more people to lift or move the set. The set is heavy and the bottom surface is flat. Serious injury can result from trying to move the set by yourself alone, or from unsteady handling. Install the set on a stable, level surface.
Attachments
Do not use attachments not recommended by the manufacturer, as they may cause hazards.
Water and Moisture
Do not use power-line operated sets near water — for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc.
Accessories
Do not place the set on an unstable cart, stand, tripod, bracket, table, or shelf. The set may fall, causing serious injury to a child or an adult, and serious damage to the set. Use only a cart or stand recommended by the manufacturer for the specific model of TV any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
Disconnect all cables and cords from the set before attempting to move the set.
Do not allow children or pets to climb up onto, or push against, the set. The set may fall, causing serious injury.
Ventilation
The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of the set, and to protect it from overheating, these slots and openings must never be blocked or covered.
•Never cover the slots and openings with a cloth or other materials.
•Never block the slots and openings by placing the set on a bed, sofa, rug or other similar surface.
•Never place the set in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided.
•Do not place the set near or over a radiator or heat register, or where it is exposed to direct sunlight.
Power-Cord Protection
Do not allow anything to rest on or roll over the power cord, and do not place the set where the power cord is subject to wear or abuse.
Grounding or Polarization
This set may be equipped with a polarized alternating current line plug (a plug having one blade wider than other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact you electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
Antennas
Outdoor Antenna Grounding
If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in USA and Section 54 of the Canadian Electrical Code in Canada provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Antenna Grounding According to the NEC
Refer to section 54-300 of Canadian Electrical Code for Antenna Grounding.
|
ANTENNA |
|
LEAD IN |
|
WIRE |
GROUND |
|
CLAMP |
|
|
ANTENNA |
|
DISCHARGE UNIT |
|
(NEC SECTION 810-20) |
ELECTRIC |
|
SERVICE |
GROUNDING CONDUCTORS |
EQUIPMENT |
(NEC SECTION 810-21) |
|
GROUND CLAMPS |
|
POWER SERVICE GROUNDING |
NEC - NATIONAL ELECTRIC CODE |
ELECTRODE SYSTEM |
(NEC ARTICLE 250, PART H) |
Lightning
For added protection for this television receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the receiver due to lightning and power-line surges.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer servicing to qualified service personnel under the following conditions:
•When the power cord or plug is damaged or frayed.
•If liquid has been spilled into the set.
•If the set has been exposed to rain or water.
•If the set has been subject to excessive shock by being dropped, or the cabinet has been damaged.
•If the set does not operate normally when following the operating instructions. Adjust only those controls that are specified in the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the set to normal operation.
•When the set exhibits a distinct change in performance — this indicates a need for service.
Servicing
Do not attempt to service the set yourself since opening the cabinet may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Replacement Parts
When replacement parts are required, be sure the service technician certifies in writing that he has used replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.
Safety Check
Upon completion of any service or repairs to the set, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the set is in safe operating condition, and to so certify. When the set reaches the end of its useful life, improper disposal could result in a picture tube implosion. Ask a qualified service technician to dispose of the set.
Contents |
|
|
|
Introduction |
|
|
|
Trinitron® Color TV Features |
............................ |
1 |
|
Batteries for the Remote Control....................... |
2 |
||
About this Manual |
.............................................. |
|
2 |
Connecting Your TV |
|
|
|
Basic Connections................................................ |
|
|
3 |
Cable Box Connections ....................................... |
|
4 |
|
Connecting Additional Equipment .................. |
6 |
||
Using the Remote Control and Basic Functions |
|||
Using the Remote Control................................ |
|
15 |
|
Setting Up the TV Automatically.................... |
17 |
||
Using Picture in Picture (PIP).......................... |
18 |
||
Quick Start to the Menus.................................. |
|
20 |
|
Using the Menus |
|
|
|
Using the Video |
Menu............................... |
|
23 |
Using the Audio |
Menu............................... |
|
24 |
Using the Channel Setup |
Menu ................ |
26 |
|
Parental Control................................................. |
|
|
28 |
Using the Parental Control |
Menu ............ |
31 |
|
Using the Timer |
Menu ................................ |
|
34 |
Using the Setup |
menu ................................ |
|
35 |
Using the Basic |
Menu ................................. |
|
36 |
Other Information |
|
|
|
Programming the Remote Control ................. |
37 |
||
Troubleshooting ................................................ |
|
|
40 |
Specifications...................................................... |
|
|
43 |
Index.......................................................................... |
|
|
45 |
Connecting Additional Equipment
Introduction
Congratulations on your purchase of the Sony Trinitron® Color TV. Before you begin using this manual, please check the model number located on the rear of your TV or on the front cover of this manual.
Trinitron® Color TV Features
Some of the features you will enjoy include:
FLAT CRT — New technologically advanced screen for optimal picture quality.
Parental Control — A tool for parents to help monitor what their children watch on TV by establishing rating limits.
Favorite Channel — Instant access to your favorite channels with the touch of a button.
Picture in Picture (PIP) — Allows you to view two channels simultaneously (KV-27FV16, KV-27FS16, KV-32FS16 only).
Universal Remote Control — Program your remote control to operate your connected cable box, VCR, digital satellite receiver, or DVD player.
Energy Star® — A recognized symbol of energy efficiency.
S VIDEO — A video input that offers enhanced picture quality.
Direct MTS — Allows direct access to changing your Multi-Channel TV Sound: Stereo, Mono, or Auto-SAP (Second Audio Program), with the touch of a button.
Trilingual Menus — Choose between English, French, or Spanish menus.
Front Panel Controls — Allows for access to the on-screen menus without the use of a remote control.
Front A/V inputs — A quick connection for video games, camcorders, or stereo/mono equipment.
1
Operating Instructions
Batteries for the Remote Control
Insert two AA (R6) batteries (supplied) into the remote control using the following illustration as a guide.
Under normal conditions, batteries will last up to six months. If the remote control does not operate properly, the batteries might be worn out.
If you will not be using the remote control for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
Your remote control can be programmed to operate most video equipment, (see page 37).
About this Manual
This manual provides instructions to help you enjoy your new TV. It shows you how to connect to an antenna or cable, cable box, VCR, DVD, satellite receiver, stereo system or camcorder. Once you are connected, follow the instructions and use the remote control to access the on-screen menus.
The TV front and rear panels illustrated in this manual are for KV-27FS12, KV-27FS16, KV-32FS12, and KV-32FS16. The rear panel shown on page 13 is for KV-27FV16. Your front and rear panels may not look exactly like those illustrated.
2
Connecting Your TV
Connecting Your TV
Read this chapter before setting up your TV for the first time. This section covers basic connections in addition to any optional equipment you may be connecting.
Basic Connections
TV with indoor or outdoor antenna, or CATV cable
Depending on the cable available in your home, choose one of the connections below:
If you are connecting to an indoor or outdoor antenna, you may need to adjust the orientation of the antenna for best reception.
3
Operating Instructions
Cable Box Connections
Some cable TV systems use scrambled or encoded signals that require a cable box to view all channels. If you subscribe to that kind of cable service, use this connection. Scrambled signals coming in to the TV through the cable box cannot be viewed in PIP. If some of your channels are scrambled, consider using the Cable Box and Cable connection (see page 5).
Cable Box and TV
Cable Box
1
Rear of TV
From cable
2
1 Connect the coaxial cable from your cable service to the IN jack on your cable box.
2 Connect a coaxial cable (not supplied) from the OUT jack on your cable box to the VHF/UHF jack on your TV.
If you will be controlling all channel selection through your cable box, you should consider using the Channel Fix feature by setting your TV to channel 3 or 4, (see page 27).
4
Connecting Your TV
Cable Box and Cable
Use this connection if you subscribe to a cable system that scrambles some channels (pay channels), but not all of them. This set up allows you to use the remote control to:
a)change channels through your cable box when you are receiving a scrambled signal, and
b)change channels through your TV.
This connection also allows you to use the PIP feature when you are viewing unscrambled channels coming directly into your TV from your cable. Scrambled signals coming through the cable box cannot be viewed in PIP. For more information on the PIP feature, see page 18.
Cable Box
Rear of TV
3 
Coaxial Cable
2
75-ohm coaxial cable
1
CATV cable (unscrambled Channels)
1 Connect the coaxial cable from your cable service to the VHF/UHF jack on your TV.
2 Using a coaxial cable (not supplied), connect the IN jack on your cable box to the TO CONVERTER jack on your TV.
3 Using a coaxial cable (not supplied), connect the OUT jack on your cable box to the AUX jack on your TV.
Pressing the 
button on the remote control switches between the cable box and direct cable inputs.
Your Sony remote control can be programmed to operate your cable box, (see page 38).
To use the cable box to change your channels, set your TV to channel 3 or 4. Setting the Channel Fix feature will assure you don’t accidentally switch the channels using your TV, (see page 27).
5
Operating Instructions
Connecting Additional Equipment
TV and VCR
Rear of TV
2
VCR
1
From cable/ antenna
Video (yellow)
Audio L (white)
Audio R (red)
Optional connection
To watch video programs from your VCR, tune your TV to channel 3 or 4 (as set on the rear of your VCR).
1Connect the coaxial cable from your TV antenna or cable service to the IN jack on your VCR.
2Using a coaxial cable (not supplied), connect the OUT jack on your VCR to the VHF/UHF jack on the TV.
Optional connection
If your VCR is equipped with video outputs, you can get better picture quality by connecting Audio/Video cables (not supplied) from AUDIO and VIDEO OUT on your VCR to AUDIO/VIDEO IN on your TV.
For optimum picture quality, use S VIDEO instead of the yellow Audio/ Video cable. S VIDEO does not provide sound; the audio cables must still be connected.
You can use the 
button to switch between the VHF/UHF and VIDEO inputs.
6
Connecting Your TV
TV, VCR, and Cable Box
Use this connection if you subscribe to a cable system that scrambles some channels (pay channels), but not all of them. This set up allows you to use the remote control to:
a)change channels through your cable box or VCR when you are receiving a scrambled signal, and
b)change channels through your TV.
This connection also allows you to use the PIP feature when you are viewing unscrambled channels coming directly into your TV from your cable. Scrambled signals coming through the cable box cannot be viewed in PIP. For more information on the PIP feature, see page 18.
Rear of TV
2b |
VCR |
Video (yellow) |
|
||
|
|
Audio L (white) |
|
|
Audio R (red) |
|
3 |
|
1 Splitter |
Cable Box |
|
|
|
Optional connection
Cable |
2a |
1 Connect the single input jack of the splitter to your incoming cable connection.
2 Using a coaxial cable (not supplied), connect the two output jacks of the splitter to:
a)the IN jack on your cable box, and
b)the VHF/UHF jack on the TV.
3 Using a coaxial cable (not supplied), connect the OUT jack on your cable box to the IN jack on your VCR.
(continued)
7
Operating Instructions
If you will be controlling all channel selections through your cable box, you should consider using the Channel Fix feature by setting your TV to channel 3 or 4, (see page 27).
Optional connection
If your VCR is equipped with video outputs, you can get better picture quality by connecting Audio/Video cables (not supplied) from AUDIO and VIDEO OUT on your VCR to AUDIO/VIDEO IN on your TV.
For optimum picture quality, use S VIDEO instead of the yellow Audio/Video cable. S VIDEO does not provide sound; the audio cables must still be connected.
You can use the 
button to switch between the VHF/UHF and VIDEO inputs.
8
Loading...