4-205-029-12
R
Trinitron Colour
Television
Instruction Manual |
GB |
|
|
Styrfunktioner |
SE |
|
|
|
|
Bruksanvisning |
NO |
|
|
|
|
Betjeningsvejledning |
DK |
|
|
Kayttöohje |
FI |
|
|
O‰ËÁ›Â˜ Xp‹Û˘ |
GR |
|
|
Bedienungsanleitung |
DE |
KV-28FC60/28FC60/Z KV-32FC60/32FC60/Z
©1999 by Sony Corporation Printed in UK
NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM
A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.
Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS 1362 (i.e. marked with 2or @) must be used.
When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please contact your nearest Sony service station.
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace the fuse.
•IMPORTANT
If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and
an appropriate plug fitted in accordance with the following instructions:
The wires in this mains lead are coloured in accordance with the following code:
Blue |
Neutral |
Brown |
Live |
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. Do not connect either wire to the
earth terminal in the plug which is marked by the letter E or by the safety earth symbol |
|
|
|
|
|
or |
|
|
|
|
|
||
coloured green or green and yellow. |
|
|
|
|
||
|
|
|
|
WARNING
•To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket outlet. This plug cannot be used and should be destroyed.
•To prevent fire or shock hazard, do not expose the unit to rain or moisture.
•Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to qualified personnel only.
GB
1
Safety First
TV sets operate on extremely high voltages. To prevent fire or an electric shock, please follow the safety information below:
For General Safety
ϖThis TV set is designed to receive and reproduce audio and video signals. Any other use of the TV set is not permitted.
ϖNever open the rear cabinet.
ϖRefer servicing to qualified personnel only!
ϖDo not expose the TV set to rain or moisture.
For Safe Installation
ϖDo not block or cover the ventilation openings. For ventilation leave a space of at least 5 cm around the set.
ϖDo not install the TV set in hot, humid or excessively dusty places.
ϖDo not install the TV set where it may be exposed to mechanical vibrations.
ϖPlace the TV set only on a stable stand designed for the weight and dimensions of the TV.
For Safe Operation
ϖOperate the TV set only on a 220240 V. AC, 50 Hz supply.
ϖUnplug the TV set if any liquid or solid object falls in through the ventilation openings. Have it checked immediately!
ϖWhen not in use, do not leave the TV set in standby mode. Disconnect the TV set if you are not going to use it for a longer period.
ϖDisconnect the TV set only by pulling on the mains plug. Do not pull on the power cord itself.
ϖIn the event of a thunderstorm, you should not touch the aerial, mains plug or television. It could possibly cause an electric shock.
For Maintenance
ϖWhen the TV is switched off, clean the screen with a soft dampened cloth. Do not use any abrasive cleaners.
ϖDust and nicotine deposits may cause heat accumulation inside the TV set.
In the long term this could be a safety risk and may shorten the lifetime of your TV set. Therefore have your set serviced about every five years.
2
Table of Contents
Installation |
|
4 |
1. |
Checking the accessories supplied |
4 |
2. |
Inserting batteries into the remote control |
4 |
3. |
Connecting the TV |
5 |
4. |
Switching on the TV |
6 |
5. |
Using your joystick |
6 |
6. |
Tuning your TV |
7 |
7. |
Finding your video channel |
7 |
Operation |
8 |
Overview of the TV set buttons |
8 |
Overview of the remote control buttons |
9 |
NexTView |
10 |
Teletext |
12 |
Using the TV menu system |
14 |
Adjusting picture and sound |
14 |
Using the Features menu |
16 |
Changing the screen mode |
17 |
Sorting TV channels |
18 |
Manually tuning in channels |
18 |
Naming a channel |
19 |
Skipping programme positions |
19 |
Using the Further Programme Preset function |
20 |
Adjusting the picture geometry for an RGB source |
20 |
Adjusting the picture rotation |
21 |
Changing the speaker configuration for external loudspeakers |
21 |
Inputting your Personal ID |
22 |
Presetting and labelling of input sources |
22 |
Optional Equipment |
23 |
Selecting an input signal |
23 |
Smartlink |
24 |
Remote control of other Sony equipment |
24 |
Additional Information |
25 |
Specifications |
25 |
Troubleshooting |
26 |
Channel Guide |
26 |
3
Installation
Follow steps 1-7 to install the TV and view TV programmes.
1. Checking the accessories supplied
2 x batteries (AA size)
1 x remote control
2. Inserting batteries into the remote control
Always remember to dispose of used batteries in an environmentally friendly way.
4
Installation
3. Connecting the TV
Connecting an aerial to your TV
1 |
1 |
2 S 2 |
3 |
3 |
L/G
S/I
R/D
D/D
R/D/D/D L/G/S/I
If you are not connecting your TV to a VCR, please connect the aerial lead (as shown left) and proceed to section ‘4.Switching on the TV‘.
If you are connecting your TV to a VCR please refer to the section below.
1 Connect your existing aerial lead to the socket marked ˘on the rear of the TV set.
Connecting an aerial and VCR to your TV
11 2 S 2 3 S 3
L/G |
S/I |
R/D
D/D
R/D/D/D L/G/S/I
The scart lead is optional. If it can be used however, this
additional connection can improve picture and sound quality when in play mode.
(existing aerial lead)
(scart lead - not supplied)
IN
AC IN |
OUT |
1Connect your existing aerial lead to your VCR as shown.
2Connect the VCR aerial lead from the RF OUT socket on the back of the VCR to the aerial socket on the back of the TV as shown.
3Connect the VCR set to the mains and switch on.
4Insert a pre-recorded tape into the VCR and press the ‘PLAY‘ button.
5
Installation
4. Switching on the TV
1 Connect the TV plug to the mains socket (220-240 V. AC, 50 Hz).
2 Push in the on/off button Uon the front of the TV.
If the standby mode indicator uon the front of the TV is lit, press the TV button on the remote control to switch on the TV set. Please be patient as the picture may take a few moments to appear on the TV screen.
5. Using your joystick
Moving the |
Pressing the |
joystick |
joystick |
|
|
To move around the menus press |
To select an item in a menu press the |
the relevant arrow button. |
joystick down in the middle. |
6
Installation
6. Tuning your TV
Before you tune your TV, you will be asked to set your language and country.
1The Language/Country menu appears on the TV screen with the word ‘English‘ highlighted.
2Push the joystick to $or 4 to select your chosen language then press the OK button to confirm. The country menu appears on screen with the word ‘OFF‘ highlighted. Select ‘OFF‘ if you do not want your channels stored in a given channel sequence starting from programme position 1.
3Push the joystick to $or 4 to select the country in which you wish to operate the TV.
Language/Country |
|
Language |
ˇ |
Cestinaˇ |
|
Country |
Dansk |
Deutsch |
|
|
English |
|
Español |
|
Français |
|
Italiano |
Select language: |
Confirm: OK |
Language/Country |
|
Language |
English |
Country |
Off |
|
Austria |
|
Belgium |
|
Bulgaria |
|
Czech Rep. |
|
Denmark |
|
Finland |
Select Country: |
Confirm: OK |
4Press the OK button to confirm your choice. The ‘Setup‘ menu appears on the TV screen.
5Push the joystick to $or 4 to select ‘Auto Tuning‘ then press the OK button to confirm.
Set Up |
|
|
Auto Tuning |
Start |
|
Programme Sorting |
|
|
AV Preset |
|
|
Installation |
|
|
Select: |
Start Auto Tuning: |
6 Push the joystick to ”and hold for 5 seconds.
ϖ |
Your TV will now start to tune in all available |
1 |
CO2 |
|
channels. This may take a few minutes - please be |
2 |
CO3 |
|
3 |
CO4 |
|
|
patient and do not press any buttons. Once the TV |
4 |
CO7 |
|
5 |
CO8 |
|
|
|
||
|
has tuned all available channels the menu disappears |
|
Searching |
|
|
|
|
|
from the screen and your TV is ready to use. |
|
|
ϖIf you would like to stop the autotune process at any stage, press the OK button. The manual sort menu appears on the TV screen. For manual sorting instructions refer to the ‘Sorting TV channels‘ section of this instruction manual. To remove the sorting menu, press the MENU button on your remote control.
7. Finding your video channel
If you have connected a VCR to your TV, you now need to find your video channel.
1.Press the PROGR+/- buttons on your remote control until your video picture appears on the TV screen.
ϖIf you wish to move your video channel to a different programme position, refer to the ‘Sorting TV channels‘ section of this instruction manual.
7
Operation
Overview of the TV set buttons
You must press the control button to activate and illuminate the control panel before you can use the other buttons on top of the TV set.
Video input button. |
Volume control buttons. |
|
|
Programme Up (+) or |
||||||||||||||||
Press to increase (+)/ |
|
|
|
|||||||||||||||||
|
|
|
Down (-) buttons. |
|||||||||||||||||
Press to select the input signals |
|
|
|
|||||||||||||||||
decrease (-) volume. |
|
|
|
|||||||||||||||||
|
|
|
Press to select TV |
|||||||||||||||||
from VCR etc. |
|
|
|
|||||||||||||||||
|
|
|
|
|
|
|
|
|
||||||||||||
|
|
|
|
|
|
|
|
|
channels. |
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CONTROL button. |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Press to activate and |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
illuminate the control panel. |
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
– |
+ |
|
|
PROGR |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
– |
+ |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CONTROL |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
On/Off switch.
Press to switch TV on and off.
8
Operation
Overview of the remote control buttons
To mute sound.
Press to mute TV sound. Press again to restore the sound.
To return to TV mode.
Press to return to the normal operation from teletext mode, video mode or standby mode.
These buttons have no function.
To select Teletext
Press to select Teletext mode.
To select EPG
Press to display the Electronic Programme Guide. Press again to remove display.
To freeze the picture.
Press to freeze the picture. Press again to cancel freeze.
To select channels.
Press numbered buttons to select channels.
For double digit programme numbers, eg 23, press -/-- first, then the buttons 2 and 3. If you enter an incorrect first digit, this should be corrected by entering another digit (0-9) and then selecting -/-- button again to enter the programme number of your choice.
To display sound menu.
Press repeatedly to select one of the following equaliser modes : Personal, Vocal, Jazz, Rock, Pop or Flat.
To display picture menu.
Press to change the picture settings. Press the ; button to remove the display.
To adjust TV volume.
Press to adjust the volume of the TV.
To reset to factory-set levels.
Open the remote control lid and press to return picture and sound settings to factory-set levels. After the ‘Installation‘ menu has appeared on the TV screen, refer to the ‘Selecting Language and Country‘ section of the instruction manual to change your choice of language and country if desired.
VCR on/off button.
Press to temporarily switch off VCR (if Sony VCR connected). Press again to switch on VCR.
To temporarily switch off TV
Press to temporarily switch off TV. Press again to switch on TV from standby mode.
NOTE: After 15 minutes without a TV signal and without any button being pressed, the TV switches automatically into standby mode.
To reveal channel information.
Press to reveal information on the channel you are currently watching. Press the ;+ button again to remove the display.
To select input signal or freeze teletext
Press to select inputs from the TV sockets (see Using Optional Equipment section). In teletext mode, press to freeze the displayed page. Press once again to cancel.
To return to previous channel
Press to return to the previous channel you were watching. Note: This can be done only after watching the present channel for 5 seconds.
To change screen format.
Press to change the size of the screen.
This button can be used in Teletext mode only. Please see Teletext section of manual for details.
To select menu items
Use this OK button to select options available in the menu system of the TV.
To display the |
|
|
|
|
|
Channel Table |
|
|
|
|
|
Press the OK button to |
|
|
|
|
|
|
|
|
|
|
|
display the channel |
8 |
VIVA |
Soul Music |
||
9 |
RTL |
News |
|||
table. Push to $or 4to |
|
10 |
SAT 1 |
Game Show |
|
|
11 |
S3 |
Animal Report |
||
12 |
VIVA 2 |
Stones in Interviev |
|||
select a channel then |
13 |
PRO 7 Pink Panther |
|||
14 |
ARD |
Afternoon Report |
|||
|
|||||
|
|
|
|
|
push to ”to confirm.
To select channels.
Press to select channels.
To display the menu
Press if you wish to use the TV menu system. Press again to remove the menu from the TV screen.
To display the time.
Open the remote control lid and press to display the time on screen.
To operate video equipment
Open the remote control lid and press these buttons to operate your video equipment (please refer to your VCR manual).
9
Operation
NexTView*
*depending on availability of service
NexTView is an electronic programme guide with up to 1 week* of programme information on those channels included in the selected provider.
*If the data exceeds the memory of NexTView, you will get information on less than 7 days.
When looking for information you can search by theme (sports, art etc.), date or time (e.g. broadcasts between 8 and 9 p.m). When you‘ve found a programme you can go directly to this programme, use the timer to remind you of it or preset your VCR with Smartlink.
The NexTView provider is responsible for the contents of the guide. The TV set is responsible for the presentation, that is the menu structure and the navigation, if there is none from the provider. If there is a navigation from the provider the basic operation with the joystick is the same as described in the Sony navigation.
Displaying NexTView
At first you need to select a channel providing a NexTView Service. In this case the indication “NexTView“ is displayed as soon as all data is available. When you later change the channel you can still select this NexTView service.
1Press to switch NexTView on and off.
2Use the joystick buttons as follows
•moving upor downwards within a column: Use $or 4
•Going to the left columns time and date: Use “
•Going to the right column icons: Use ”
•Confirming a selection: Press OK
awhile in the columns date, time or icon (themes), the programme list changes according to the selection.
bwhile in the programme list, confirming a running broadcast brings you directly to the TV programme or confirming a future programme brings you to the long info menu (See Using the Long Info Menu).
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
07 Tue |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
12:38 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
SWISS |
|
TXT |
|
|
TPS / RINGIER |
|
|
|
|
|
|
7 |
|
|
|
Star Wars |
|
|
|
Tue 07. 04 .98 |
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
Tue |
|
|
|
Super RTL |
10:35 - 12:45 |
|
|
|
|
|
|
|
|||
8 |
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
Vets in Practice |
|
|
|
|
|
|
|
|
|
|
||
Wed |
|
|
|
|
|
|
|
|
|
|
|
|
|
||
9 |
|
|
|
C5 |
10:20 - 12:00 |
|
|
|
|
|
|
|
|||
|
|
|
Flui grüsst den Rest der Welt |
|
|
|
|
|
|
|
|||||
Thu |
|
|
|
|
|
|
|
|
|
|
|||||
10 |
12 |
|
|
Kabel 1 |
10:45 - 10:50 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fri |
|
|
|
Once upon a time in the West |
|
|
|
|
|
|
|
||||
11 |
|
|
|
Euronews |
11:00 - 11:20 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sat |
|
|
|
International News |
|
|
|
|
|
|
|
||||
12 |
|
|
|
RTL Plus |
11:45 - 12:50 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sun |
|
|
|
Documentary series which follows veterinary |
|
|
|
|
|||||||
13 |
|
|
|
graduates as they embark on their careers. |
|
|
|
|
|||||||
|
|
|
Continues on Friday |
|
|
|
|
|
|
|
|||||
Mon |
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Index
|
full list of selection |
|
sports |
|
|||
|
|||
|
personal selection |
|
entertainment |
|
|
||
|
news broadcasts |
|
children |
|
movies |
|
back to last menu |
10
Operation
Using the Individual Setting menu
When you select there will be no personal pre-selection. lets you make your own individual selection of themes, limiting the search to the marked ones.
1 Select using 4or $. Push to ”to enter. The Individual Setting menu is displayed.
2Select the item you wish to mark using 4 or $. Confirm by pressing OK. Repeat step 2 for all items you wish to have in your list.
3When you have finished the list, press ”to select on the menu screen then press OK.
Using the Long Info menu
1 Select a future programme in the column programme list using 4or $. Press OK. The long info menu is displayed.
07 Tue 12:38
First nextTView/EPG-Providers in Europe
SWISS |
TXT |
|
TPS / RINGIER |
nexTView |
|
|
|
Tue 07. 04 .98 |
|
Address Mapping
The position of the addresses in the OSDA is shown in the following diagram. The position values of the DPW are set to '0'.
If other values are set, the complete combination will be scrolled.
Example:
if the DPWC is set to '63', the char-
This channel has been set for a timer
|
|
|
|
|
|
|
VPS/PDC |
On |
|
|
|
|
Speed |
SP |
|
|
|
|
Timer Prog |
|
|
|
|
|
VCR1 |
|
|
|
|
|
|
|
|
|
|
You wish to record the selected programme with your VCR
(only with Smartlink VCRs)
2 Select using “and press OK.
The information is transferred to the VCR connected to your TV set.
Setting up your VCR
3Select VPS/PDC pushing repeatedly to “.
With this setting on, you have the guaranteed recording of the whole broadcast should there be a change in the TV programme. This only works if the selected channel broadcasts a VPS/PDC signal.
•Select On or Off using OK.
4Select Speed using $.
Select between standardplay (SP) or longplay (LP) mode. With longplay you can record twice as much on a videotape. The picture quality, however, may suffer.
•Select SP or LP using OK.
5Select VCR Setup using $.
Select with which of the connected Smartlink-VCRs you wish to programme.
• Select VCR 1 or 2 using OK.
To leave the menu
6 Select using z. Press OK. You are back in the last menu.
|
|
|
|
|
|
|
VPS/PDC |
On |
|
|
|
|
Speed |
|
|
|
|
|
SP |
|
|
|
|
|
|
|
|
|
|
|
VCR Setup |
VCR1 |
|
|
|
|
|
|
|
|
|
11
Operation
Teletext
Most TV channels broadcast information via teletext. The index page of the teletext service (usually page 100) gives you information on how to use the service.
Please use a TV channel with a strong signal, otherwise there may be
Teletext errors.
Switching Teletext on and off
1Select the TV channel which carries the teletext service you want to view.
2a Press the button once on your remote control to switch Teletext on. b Press again for Mix mode.
The TV broadcast and the Teletext display are overlapped.
3 Press ;or press a third time to switch teletext off.
Selecting a Teletext Page
Input the three digits of the page number using the number buttons on your remote control.
If you have made a mistake:
Type in any three digits, then re-enter the correct page number.
Page Catching
1Using the number buttons on the remote control, select a teletext page which has several page numbers on it (e.g. the index page).
2Press the OK button.
Page Catching is displayed.
3 Select the desired page number using 4or $then press the OK button. The requested page is displayed after some seconds.
Selecting the next or the preceding page
• Press (Page +) or (Page -).
Selecting the index page
• |
Press ;+ . |
|
|
Selecting a subpage |
|
||
|
A teletext page may consist of several subpages. In this case an information line |
216-02 |
|
|
|||
|
is displayed, showing the number of subpages. |
||
• |
|||
Select the mode by pushing to 4. Select the subpage by using 4or $. |
|
Freezing a Teletext subpage
1 Press to freeze the Teletext page.
2 |
Press |
to resume normal teletext reception. |
01 |
02 |
03 |
04 |
05 |
06 |
07 |
08 |
|
|
|
|
|
|
|
|
Using Fastext*
*depending on availability of service
Fastext lets you access pages with one button stroke. When Fastext is broadcast, a colour-coded menu appears at the bottom of the screen. The colours of this menu correspond to the red, green, yellow and blue buttons on the remote control.
• Press the coloured button which corresponds to the colour in the colour-coded menu.
12
Operation
Using the Teletext menu
This TV set has a menu-guided teletext system. When teletext is switched on you can use the joystick buttons to operate the teletext menu.
Select the menu functions as follows:
1Press the MENU button on the remote control to display the Teletext menu.
2Select the teletext function using 4or $. Push to ”to enter.
Top/Bottom/Full
For convenient reading of a Teletext page you can enlarge it.
After having selected the function, a sub menu Top 4Bottom $Full OK is displayed.
•Push to 4to enlarge the upper half of the screen, push to $to enlarge the lower
half. Press OK to resume the normal size. Press to resume the normal Teletext operation.
Teletext
Top / Bottom / Full
Text Clear
Reveal
Time Page
Select: |
Enter Menu: |
Top: Bottom: Full: OK
Text Clear
After having selected the function, you can watch a TV channel while waiting for a requested Teletext page. As soon as the page is available, the symbol changes colour.
• Press |
to view the page. |
Reveal
Some teletext pages contain hidden information (e.g., for a quiz), which you can reveal.
After having selected the function, the hidden information appears.
• Press to resume the normal Teletext operation.
Time Page*
*depending on availability of service
You can call up a time-coded page - such as an alarm page - at a time specified by you.
After having selected the function a sub menu is displayed.
1Select On using 4or $. Push to ”to enter.
2Enter the three digits of the desired page using the number buttons.
3Enter the four digits of the desired time using the number buttons.
4Press OK to store.
The time is displayed in the top left-hand corner of the screen.
At the requested time the page is displayed.
Time Page |
|
PAGE |
TIME |
– – – |
- - : - - |
Select: Enter:
13
Operation
Using the TV menu system
The TV consists of a menu system which is based on a series of user friendly on-screen displays and menus. These displays will help you get the most from your TV, helping you to change picture and sound settings, to alter the size of the TV picture and to rearrange the TV channels etc.
Adjusting the picture and sound
Picture and sound are adjusted at the factory. You can however, adjust them individually.
1 Press MENU.
Select the symbol for Picture or for Sound using 4or $. Push to ”to enter.
The menu Picture or Sound Control is displayed.
2Select the desired item using 4or $. Push to ”to enter.
3Adjust the selected item using 4, $, ”and “. Press OK to store.
Refer to the tables on this and the following page for more information.
4Repeat steps 2 and 3 to adjust other items.
5Press MENU to return to the normal TV screen.
Picture Control
Item |
Effect/Operation |
|||
Picture Mode |
$ |
Live |
|
(for live broadcasts) |
|
|
Personal (for individual settings) |
||
|
4 |
Movie |
(for movie broadcasts) |
|
|
|
|
|
|
Contrast |
Less |
|
“ |
” More |
Brightness* |
Darker |
“ |
” Brighter |
|
Colour* |
Less |
|
“ |
” More |
Hue** |
Reddish |
“ |
” Greenish |
|
Sharpness* |
Softer |
“ |
” Sharper |
|
Reset |
Resets picture to the factory preset levels |
|||
AI |
4 |
Off: normal |
||
(Artificial Intelligence) |
$ On: Automatic optimization of contrast level |
|||
|
|
according to the TV signal |
||
Noise Reduction |
4 |
Off: Normal |
||
|
$ On: Reduces picture noise in case of a weak |
|||
|
|
broadcasting signal |
||
Digital Mode |
$ |
Normal: 100 Hz. |
||
|
|
Digital+: 100 Hz plus line flicker reduction |
4Advanced: Digital+ plus smoothing of motions
*Only if Personal is selected in Picture Mode
**Only available for NTSC colour signal (e.g. US video tapes)
|
Picture Adjustment |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
Picture Mode |
Personal |
|
||||||
|
Contrast |
|
|
|
|
|
|
|
|
|
Brightness |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
Colour |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
Sharpness |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
Reset |
|
|
|
|
|
|
||
|
AI |
|
|
|
|
On |
|
|
|
|
Noise Reduction |
|
|
|
|
On |
|
|
|
|
Digital Mode |
|
|
Normal |
|
Select Mode: Enter:
|
|
Live |
|
|
|
Personal |
|
|
Picture Mode |
|
|
|
Movie |
|
|
|
|
|
|
Contrast
|
|
On |
|
|
AI |
Off |
|
|
|
|
|
|
|
|
|
|
Noise Reduction |
On |
|
|
Off |
|
|
|
|
|
|
|
|
Normal |
|
|
Digital Mode |
Digital + |
|
|
Advanced |
|
|
|
|
|
|
14
Operation (TV menu system):
Sound Control
Item |
Effect/Operation |
|
Equaliser mode |
Select between the following sound settings |
|
|
$ |
Personal |
|
|
Vocal |
|
|
Jazz |
|
|
Rock |
|
|
Pop |
|
4 |
Flat (fixed setting, cannot be adjusted) |
Equaliser adjustment |
|
You can adjust the mode selected in Equaliser |
|
|
mode by cutting and boosting of 5 selected |
|
|
|
|
|
frequency bands. |
|
|
Only the changes made in Personal can be stored, |
|
|
|
|
|
the others return to factory setting. |
|
|
•Select the desired bar using ”or “, adjust using 4 and $.
Press OK to store.
Balance |
” |
More right |
||
|
“ |
More left |
|
|
Loudness |
$ |
Off: Normal |
||
|
4 |
On: For music broadcasts |
||
Space |
$ |
Off: Normal |
||
|
4 |
On: Special accoustic effect |
||
Auto Volume Control |
4 |
On: volume level of the channels will stay the same |
||
|
|
|
independent of the broadcast signal |
|
|
|
|
(e.g. in case of advertisements) |
|
|
$ Off: volume level changes according to the |
|||
|
|
|
broadcast signal |
|
Dual Sound |
|
|
For a bilingual broadcast: |
|
|
$ A for channel 1 |
|||
|
4 |
B for channel 2 |
||
|
|
|
For a stereo broadcast: |
|
|
$ |
Mono |
|
|
|
4 |
Stereo |
|
|
|
|
|
In case of a NICAM stereo broadcast the indication |
|
|
|
|
||
|
|
|
NICAM appears briefly on the screen. |
|
|
|
|
||
Headphones |
|
|
|
|
2Volume |
|
|
Less “ |
”More |
2Dual Sound |
|
|
For a bilingual broadcast: |
|
|
$ A for channel 1 |
|||
|
4 |
B for channel 2 |
||
|
|
|
|
|
|
|
|
|
|
|
Personal |
|
|||
|
|
|
|
|
|
|
|
Vocal |
|
|
|
|
|
|
|
|
|
|
Jazz |
|
|
|
|
|
Audio Adjustment |
|
|
|
|
Rock |
|
|
|
|
|
|
|
|
|
|
Pop |
|
|
|
|
|
Equaliser Mode |
|
|
|
|
Flat |
|
|
|
|
|
Personal |
|
||||||
|
|
|
Equaliser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
|
Adjustment |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
|
Balance |
|
|
|
|
|
|
|
|
|
|
Loudness |
|
|
|
|
On |
|
|
|
|
|
Space |
|
|
|
|
Off |
|
|
|
|
|
Auto Vol. Control |
|
|
|
|
Off |
|
|
|
|
|
Dual Sound |
|
|
|
|
Mono |
|
|
|
|
|
Volume |
|
|
|
|
|
|
|
|
|
|
Dual Sound |
|
|
|
|
|
|
|
|
|
|
|
|
|
Mono |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Select Mode: Confirm: OK
Equaliser Adjustment
Personal |
|
|
|
|
+ |
|
|
|
|
0 |
|
|
|
|
– |
|
|
|
|
120 |
150 |
1,5K |
5 K |
10 K |
Sel: Adjust: Confirm:OK
Balance
|
|
Off |
|
|
Loudness |
On |
|
|
|
|
|
|
|
|
|
|
|
Off |
|
|
Space |
On |
|
|
|
|
|
|
|
|
|
|
|
Off |
|
|
Auto Vol. Control |
On |
|
|
|
|
|
Mono
Dual Sound |
Stereo |
Volume
|
|
A |
|
|
Dual Sound |
B |
|
|
|
|
|
15
Operation (TV menu system):
Using the Features menu
1Press the MENU button on the remote control. Select the symbol using $. Push to zto enter.
2Select the desired menu item using $. Push to zto enter.
3Select the desired setting using 4 or $.
4Store by pressing OK.
5Press MENU to return to the normal TV screen.
Features
Item |
Effect/Operation |
||
Auto Format* |
4 |
Off: |
Size of picture does not automatically adjust. |
*only for aerial signal |
|
Normal: Size of picture automatically adjusts |
|
|
|
|
according to information from broadcaster. |
|
$ |
Full: |
The TV can automatically adjust the picture |
|
|
|
size to eliminate any dark areas on the TV |
|
|
|
picture (as shown below): |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Format Correction* |
4 |
On: |
Smart mode is selected automatically for |
|||||||||
*only if Auto Format is |
|
|
|
|
4:3/14:9 broadcasts |
|||||||
set to ‘Normal‘ or ‘Full‘ |
$ |
Off: |
4:3/14:9 is selected |
|||||||||
Sleep Timer |
|
|
You can select a time period after which the TV |
|||||||||
|
|
|||||||||||
|
|
|
switches itself into standby mode |
|||||||||
|
4 |
|||||||||||
|
Off |
|
|
|
|
|
|
|
|
|||
|
|
|
10 min. |
|||||||||
|
|
|
20 min. |
|||||||||
|
|
|
. |
|
|
|
|
|
|
|
|
|
|
|
|
. |
|
|
|
|
|
|
|
|
|
|
|
|
. |
|
|
|
|
|
|
|
|
|
|
$ |
90 min. |
||||||||||
Parental Lock |
4 |
Off: Normal mode |
||||||||||
|
$ On: TV can only be switched on out of |
|||||||||||
|
|
|
standby-mode using the Remote Commander, |
|||||||||
|
|
|
the buttons on the TV do not work. |
|||||||||
AV2 Source |
|
|
You can select the source to be output from the |
|||||||||
|
|
|||||||||||
|
|
|
Scart connector Y2/j2. In this way you can |
|||||||||
|
|
|
||||||||||
|
|
|
record from this socket while watching another |
|||||||||
|
|
|
source. |
|||||||||
|
4 |
TV |
audio/video signal from the aerial ˘ |
|||||||||
|
|
|
AV1 audio/video signal from Scart 1 |
|||||||||
|
|
|
AV2 audio/video signal from Scart 2 |
$ AV3 audio/video signal from connectors on top or bottom of rear of TV.
|
|
Features |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Auto Format |
Off |
|
||
|
|
Format Correction |
Normal |
|
||
|
|
Sleep Timer |
Full |
|
||
|
|
Off |
|
|
||
|
|
Parental Lock |
Off |
|
|
|
|
|
|||||
|
|
AV 2 Source |
TV |
|
||
|
|
|
|
|
|
|
|
|
Select: |
Enter: |
|
|
|
Auto Format Off
Normal
Full
|
|
|
|
|
Format Correction |
Off |
|
|
|
On |
|
|
|
|
|
Sleep Timer |
10 min |
|
|
|
|
|
|
|
|
|
|
Parental Look |
|
Off |
|
|
|
|
|
|
On |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
AV 2 Source |
|
TV |
|
|
|
|
|
|
AV 1 |
|
|
|
|
|
|
AV 2 |
|
|
|
|
|
|
AV 3 |
|
|
|
|
|
|
|
|
|
|
16
Operation (TV menu system):
Changing the screen mode
When Auto Format in the Features menu is preset to ”Normal“ or “Full“, the TV set automatically selects the detected screen format. Screen mode, however, lets you select the screen format of your choice.
• Press the |
button on the remote control repeatedly to get one of the |
|
following formats: |
Smart |
|
|
|
|
Smart |
imitation of wide screen effect for 4:3 broadcasts, parts of the top and |
|
|
bottom of the picture are cut off |
|
4:3 |
conventional 4:3 aspect ratio, full picture information |
|
14:9 |
compromise between 4:3 and 16:9 aspect ratios |
Zoom |
Zoom |
imitation of wide screen effect for letterboxed movies |
|
Wide |
for 16:9 broadcasts |
|
In Zoom, Smart and 14:9 modes parts of the top and the bottom of the screen |
|
|
are cut off. Using 4and $you can adjust the position of the image onscreen to |
|
|
e.g. read subtitles. Press OK to confirm. |
Wide |
|
|
|
17
Operation (TV menu system):
Sorting TV channels
After tuning in TV channels, you may wish to rearrange the order of the channels.
1Press the MENU button on your remote control. Select the symbol using $. Push to ”to enter.
2Select Programme Sorting using $. Push to ”to enter.
3Select the programme position of the channel you wish to sort using 4or $. Push to ”to enter.
4Move the channel to the new programme position using 4or $. Store by pressing OK.
The channel is now at the new position. The other programme positions move accordingly.
5To sort other programme positions repeat steps 3 to 4.
6Press MENU to return to the normal TV screen.
Programme Sorting |
||
PROG |
CH |
LABEL |
1 |
C03 |
TV 5 |
2 |
C05 |
PRO 7 |
3 |
C07 |
EU-SP |
4 |
C08 |
SWF |
5 |
C09 |
RTL |
6 |
C11 |
SAT |
7 |
C12 |
MDR |
8 |
C13 |
DDI |
9 |
C14 |
DSF |
10 |
C15 |
RTL 2 |
11 |
C16 |
KAB 1 |
Select Prog: |
Confirm: |
Programme Sorting |
|
|
||
PROG |
CH |
LABEL |
|
|
1 |
C03 |
TV 5 |
C03 |
TV 5 |
2 |
C05 |
PRO 7 |
|
|
3 |
C07 |
EU-SP |
|
|
4 |
C08 |
SWF |
|
|
5 |
C09 |
RTL |
|
|
6 |
C11 |
SAT |
|
|
7 |
C12 |
MDR |
|
|
8 |
C13 |
DDI |
|
|
9 |
C14 |
DSF |
|
|
10 |
C15 |
RTL 2 |
|
|
11 |
C16 |
KAB 1 |
|
|
Select Position: |
Move: OK |
Manually tuning-in channels
Use this function to preset channels or a video input source one by one to programme positions of your choice.
1Press the MENU button on the remote control. Select the symbol using $. Push to ”to enter.
2Select Installation using $. Push to ”to enter.
Select Manual Programme Preset using $. Push to ”to enter.
3Select the programme position by pushing to 4 or $. Push twice to ”. The column SYS is highlighted.
4Select the TV system using 4or $. Push to ”to enter.
Available TV systems are I for Ireland or EXT for a video input source (please go to step 5c after selecting EXT).
5Select your method for the channel tuning using 4or $. Push to ”to enter.
You have the choice between C for a terrestrial channel, S for a cable channel or F for direct frequency input.
6a Direct Channel Input
For channel numbers input a two digit number, for the channel frequency a three digit number.
•Select the two or three digits by using the number buttons 0 to 9.
•To start the search and to store the channel, press the OK button.
•To preset other channels repeat steps 3 to 6a.
b Channel search (SEARCH)
Use Search if you do not know the channel number or frequency
•Start the search for the next available channel by pushing to $.
•Store the channel by pressing OK or continue the search by pushing again to $.
•To search for other channels repeat steps 3 to 6b.
c For video input sources (EXT)
•Select the Video Input source using 4or $.
•Store your selection by pressing OK.
•To allocate other sources repeat steps 3 to 5c.
6 Press MENU to return to the normal TV screen.
Installation |
|
|
Language/Country |
|
|
Manual Programme Preset |
||
Further Programme Preset |
||
RGB Set Up |
|
|
Picture Rotation |
O |
|
Speaker Configuration |
Internal |
|
Personal ID |
|
- - - - - - - |
|
|
|
Select: |
Enter: |
|
Manual Programme Preset |
||||
PROG |
SKIP |
SYS |
CH |
LABEL |
1 |
Off |
B/G |
C09 |
BBC1 |
2 |
Off |
B/G |
C10 |
BBC |
3 |
Off |
|
|
|
4 |
Off |
|
|
|
5 |
Off |
|
|
|
6 |
Off |
|
|
|
7 |
Off |
|
|
|
8 |
Off |
|
|
|
9 |
Off |
|
|
|
10 |
Off |
|
|
|
11 |
Off |
|
|
|
Select: |
Enter: |
|
|
PROG |
SKIP |
SYS |
CH |
LABEL |
1 |
Off |
B/G |
|
|
|
|
L |
|
|
|
|
I |
|
|
|
|
D/K |
|
|
|
|
EXT |
|
|
PROG |
SKIP |
SYS |
CH |
LABEL |
1 |
Off |
I |
C |
|
|
|
|
S |
|
|
|
|
F |
|
PROG SKIP SYS CH LABEL
1 |
Off |
I |
03 |
SEARCH
PROG |
SKIP |
SYS |
CH |
LABEL |
0 |
Off |
EXT |
AV1 |
AV1 |
|
|
|
AV2 |
|
|
|
|
AV3 |
|
18
Operation (TV menu system):
Naming a channel
During tuning the channels are usually labelled automatically.
You can, however, individually name a channel or a video input source.
1Press the MENU button on the remote control. Select the symbol using $. Push to ”to enter.
2Select Installation using $. Push to ”to enter.
Select Manual Programme Preset using $. Push to ”to enter.
3Select the programme position of the channel or the video source you wish to label by pushing to $or 4. Push repeatedly to ”until the first element of the position LABEL is highlighted.
4Select a number, a letter, + or a blank using 4or $. Push to ”to confirm. Select the other four characters in the same way.
5Store your selection by pressing OK.
6To label other channels or video sources repeat steps 3 to 5.
7Press MENU to return to the normal TV screen.
Skipping programme positions
In case of 100 programme positions there may be unused positions, which you can skip in the menu »Manual Programme Preset«. When changing channels with the PROGR +/– buttons they then do not appear.
You can, however, still select them using the number buttons.
1Press the MENU button on the remote control. Select the symbol using $. Push to ”to enter.
2Select Installation using $. Push to ”to enter.
Select Manual Programme Preset using $. Push to ”to enter.
3Select the programme position you wish to skip by pushing to 4or $. Push to ”to enter.
The column SKIP is highlighted.
4Select ON using $.
5Store by pressing OK.
6To skip other programme positions repeat steps 3 to 5.
7Press MENU to return to the normal TV screen.
Manual Programme Preset |
||||
PROG |
SKIP |
SYS |
CH |
LABEL |
1 |
Off |
B/G |
C09 |
ARD |
2 |
Off |
B/G |
C10 |
BBC |
3 |
Off |
|
|
|
4 |
Off |
|
|
|
5 |
Off |
|
|
|
6 |
Off |
|
|
|
7 |
Off |
|
|
|
8 |
Off |
|
|
|
9 |
Off |
|
|
|
10 |
Off |
|
|
|
11 |
Off |
|
|
|
Select: |
Enter: |
|
|
PROG |
SKIP |
SYS |
CH |
LABEL |
6 |
Off |
I |
C07 |
T E |
Manual Programme Preset |
||||
PROG |
SKIP |
SYS |
CH |
LABEL |
51 |
Off |
I |
C09 |
BBC1 |
52 |
Off |
I |
C10 |
BBC |
53 |
Off |
|
|
|
54 |
Off |
|
|
|
55 |
Off |
|
|
|
56 |
Off |
|
|
|
57 |
Off |
|
|
|
58 |
Off |
|
|
|
59 |
Off |
|
|
|
60 |
Off |
|
|
|
61 |
Off |
|
|
|
Select: |
Enter: |
|
|
PROG |
SKIP |
SYS |
CH |
LABEL |
53 |
Off |
I |
F189 |
- - - |
|
On |
|
|
|
19
Operation (TV menu system):
Using the Further Programme Preset function
Using the menu Further Programme Preset you can
a)individually adjust the volume level of each channel.
b)improve the quality of a weak channel (picture or sound distortions) with manual fine tuning.
c)preset the AV output for programme positions of those channels with scrambled signals (e.g. from a Pay TV decoder). In this way a connected Smartlink VCR records the unscrambled signal.
1Press MENU. Select the symbol using $. Push to ”to enter.
2Select Installation using $. Push to ”to enter. Select Further Programme Preset using $. Push to ”to enter.
3Select the programme position of the desired channel by pushing to 4or $. Push repeatedly to ”to select:
VOL (Volume Offset), AFT (Automatic Fine Tuning) or DECODER. The selected item changes colour.
4a VOL
Push to 4or $to adjust the volume level (range -7 to +7) of the channel. Store by pressing OK.
Repeat steps 3 and 4a if you wish to adjust the volume level of other channels.
bAFT
Push to 4or $to fine tune the channel (range -15 to +15). Store by pressing OK. Repeat steps 3 and 4b if you wish to fine tune other channels.
cDECODER
Push to 4or $to select AV1 (Euro AV socket 1) or AV2 (Euro AV socket 2) as output for the video source on this programme position. Store by pressing OK. Repeat steps 3 and 4c if you wish to preset the AV output of other video sources.
Should you use Auto Tuning afterwards, this setting will be cancelled.
5 Press MENU to return to the normal TV screen.
Adjusting the picture geometry for an RGB source
When connecting an RGB source such as a Sony playstation you may need to readjust the picture geometry.
1Select the connected RGB source …1 by pressing …repeatedly.
2Press MENU. Select the symbol using $. Push to ”to enter.
3Select Installation using $. Push to ”to enter. Select RGB Set Up using $. Push to ”to enter.
4Select H Centre by pushing to ”. Adjust the centre of the picture (range from -10 to +10) using 4or $. Store by pressing OK.
5Select H Size using $. Push to ”to enter. Adjust the horizontal coordinates (range from -10 to +10) using 4or $. Store by pressing OK.
6Press MENU to return to the normal TV screen.
Installation |
|
|
Language/Country |
|
|
Manual Programme Preset |
||
Further Programme Preset |
||
RGB Set Up |
|
|
Picture Rotation |
O |
|
Speaker Configuration |
Internal |
|
Personal ID |
|
- - - - - - - |
Select: |
Enter: |
|
Further Programme Preset |
|||
PROG |
VOL |
AFT |
DECODER |
1 |
0 |
On |
Off |
2 |
0 |
On |
Off |
3 |
0 |
On |
Off |
4 |
|
|
|
5 |
|
|
|
6 |
|
|
|
7 |
|
|
|
8 |
|
|
|
9 |
|
|
|
10 |
|
|
|
11 |
|
|
|
Select: |
|
Enter: |
|
PROG |
VOL |
AFT |
DECODER |
1 |
0 |
|
|
|
PROG |
VOL |
AFT |
DECODER |
|
1 |
-5 |
|
|
|
On |
|
||
|
|
|
|
|
PROG |
VOL |
AFT |
DECODER |
1 |
-5 |
On |
Off |
|
|
|
AV1 |
|
|
|
AV2 |
RGB Set Up |
|
H Centre |
O |
H Size |
O |
Adjust Position: |
Confirm: OK |
RGB Set Up |
|
H Centre |
O |
H Size |
O |
Adjust Size: |
Confirm: OK |
20
Operation (TV menu system):
Adjusting the picture rotation
Because of the earth‘s magnetism the picture might slant. In this case you can readjust the picture.
1Press MENU. Select the symbol using $. Push to ”to enter.
2Select Installation using $. Push to ”to enter. Select Picture Rotation using $. Push to ”to enter.
3Adjust the Picture Rotation (adjusting range -5 to +5) by pushing to 4or $. Store by pressing OK.
4Press MENU to return to the normal TV picture.
Installation |
|
|
Language/Country |
|
|
Manual Programme Preset |
|
|
Further Programme Preset |
|
|
RGB Set Up |
|
|
Picture Rotation |
O |
|
Speaker Configuration |
|
|
Personal ID |
|
|
Rotate: |
Confirm: OK |
|
Changing the speaker configuration for external loudspeakers
When connecting external loudspeakers to your TV set, you need to set Speaker Configuration to ‘External‘. The subwoofer of the TV set is then witched off and you will get no sound distortions.
1Press MENU. Select the symbol using $. Push to ”to enter.
2Select Installation using $. Push to ”to enter. Select Speaker Configuration using $. Push to ”to enter.
3Select External for external speakers or Internal for the internal TV speakers using 4or $. Store by pressing OK.
4Press MENU to return to the normal TV picture.
Installation |
|
Language/Country |
|
Manual Programme Preset |
|
Further Programme Preset |
|
RGB Set Up |
|
Picture Rotation |
External |
Speaker Configuration |
Internal |
Personal ID |
|
Select: Confirm: OK
21
Operation (TV menu system):
Inputting your personal ID
You can programme your TV with a safety code, so that you can be traced if your TV is stolen and recovered. This code can only be input once!
Make sure to write it down in this Instruction Manual.
1Press MENU. Select the symbol using $. Push to ”to enter.
2Select Installation using $. Push to ”to enter. Select Personal ID using $. Push to ”to enter.
3a Select the first of a total of 11 characters (letter, number, + or a blank) by using 4or $.
b Push to ”to go to the next character. c Repeat a and b for all characters.
4Store by pressing OK.
5Press MENU to return to the normal TV screen.
Installation |
|
Language/Country |
|
Manual Programme Preset |
|
Further Programme Preset |
|
RGB Set Up |
|
Picture Rotation |
|
Speaker Configuration |
|
Personal ID |
- - - - - - |
Select A-Z, 0-9: |
Confirm: OK |
Presetting and labelling of input sources
Using AV Preset you can select the automatic format function and label an input source.
1Press MENU. Select the symbol using $. Push to ”to enter.
2Select AV Preset using $. Push to ”to enter.
3Select the desired AV input (AV 1, 2 or 3) using 4or $. Push to ”enter.
After each step you have the choice between memorizing (press OK) or going to the next item (push to ”).
4For automatic format selection of the AV input:
aPush to ”to select AUTO FORMAT.
bSelect Off, Normal or Full using 4or $.
5 To label the source:
aPush to ”to select Label.
bSelect the first character using 4or $. Push to ”to confirm.
cRepeat step b to select the other 4 characters.
dStore by pressing OK.
6Repeat steps 3 to 5 for the other AV inputs.
7Selecting the AV3 Input Source:
In case of AV3 you have the choice between the top AV3 sockets on the rear of
the TV or the rear Scart 3 connector.
aPush to $to select AV3 Input. Push to ”to enter.
bSelect Top or Bottom using 4or $.
cStore by pressing OK.
8 Press MENU to return to the normal TV screen.
AV Preset |
|
|
INPUT |
AUTO 16:9 |
LABEL |
AV 1 |
On |
VIDEO |
AV 2 |
On |
VIDEO |
AV 3 |
On |
VIDEO |
AV 3 Input |
|
Rear |
Select : |
|
Enter: |
AV Preset |
|
|
|
INPUT |
AUTO 16:9 |
LABEL |
|
AV 1 |
|
On |
VIDEO |
AV 2 |
|
On |
VIDEO |
AV 3 |
|
On |
VIDEO |
AV 3 Input |
|
|
Front |
|
|
Rear |
|
Select Mode: |
Confirm: OK |
22
Optional Equipment
You can connect a wide range of optional equipment to your TV set.
D E F
1 |
1 |
2 |
2 |
3 |
3 |
|
G |
L/G |
|
S/I |
|
|
|
R/D |
R/D/D/D |
L/G/S/I |
D/D |
1 |
2 |
VHS
DVD
Selecting an input signal
In order to get the input signal of a connected equipment onto the TV screen, you need to select the symbol of the connector, to which you have connected the device.
1 Press …repeatedly on the remote control to select one of the following input modes:
Symbol on the screen |
Input signals from Connector |
…1 |
Audio/Video from Scart connector D or* RGB from Scart connector D |
…2 |
Audio/Video from Scart connector E or* S-Video from Scart connector E |
…3 |
Audio/Video from the phono jacks A and B or from Scart connector F or* S-Video from |
|
the 4-pin DIN connector C or from Scart connector F |
* automatic detection of the signal according to the connected equipment
2 Press ;to return to the normal TV screen.
ϖ If the picture or sound is distorted, move the VCR away from the TV set.
ϖWhen connecting a monaural VCR, connect only the white jack to both the TV set and the VCR.
ϖConnect your DVD-player to Scart 2 Y2/j2 E.
ϖFor information on how to select the output signal of the Scart 2 Y2/j2 E, see page 16.
23
Optional Equipment
Smartlink
Smartlink is a direct link between your TV set and a VCR.
For Smartlink you need:
ϖA VCR which supports Smartlink, NexTView Link, Easy Link or Megalogic.
ϖA fully-wired 21-pin SCART cable to connect your VCR to Scart Y2/j2 connector.
The features of Smartlink are:
ϖTuning information such as the channel overview are downloaded from the TV set to the VCR.
ϖWith NexTView you can programme your VCR easily.
ϖDirect TV recording: While watching TV you just need to press just one button on the VCR to record this programme.
For more information on Smartlink please refer to the Instruction Manual of your VCR.
Remote control of other Sony equipment
Using the buttons underneath the cover of the remote control you can control other Sony equipment.
1Open the cover of the remote control.
2Set the selector VTR 1234 DVD according to the equipment you want to control: VTR 1 Beta VCR
VTR 2 8 mm VCR
VTR 3 VHS VCR
VTR 4 Digital Video (DCR-VX 1000/9000 E, VHR-1000)
DVD Digital Video Disk
3Use the buttons on the remote control to operate the equipment.
ϖIf your video equipment has a COMMAND MODE selector, set this selector to the same position as the VTR 1234 DVD selector on the TV remote control.
ϖIf the equipment does not have a certain function, the corresponding button on the remote control does not work.
24
Additional Information
Specifications
Television B/G/H, D/K, I, L system
Colour PAL, SECAM, NTSC 3.58/4.43 (via Video In) system
Channel See Channel Guide on next page coverage
Picture tube FD Trinitron
KV-28FC60/28FC60-Z Approx. 71 cm (28 inches)
Approx. 66 cm picture measured diagonally 102° deflection
KV-32FC60/32FC60-Z Approx. 82 cm (32 inches)
Approx. 76 cm picture measured diagonally 102° deflection
Sockets Y1/1: 21-pin scart connector (Rear) input of audio/video or RGB signals
output of TV signals Y2/j2:21-pin scart connector
input of audio/video or S-video signals selectable output of audio/video signals
Y3/j3:21-pin scart connector
input of audio/video or S-video signals output of audio/video signals (monitor out)
|L/G/S/I RCA-connectors,
R/D/D/D variable output for audio signals
External speaker terminals:2-pin DIN (2) q3 : 4-pin DIN
input of S-video signals
…3 Phono jack input of video signals
≤ 3 Phono jacks input of audio signals
Sockets 2Headphones jack -stereo minijack
(Front)
Sound output |
Right and left speaker |
||
|
2 |
x |
25W (music power), |
|
2 |
x |
15W (RMS) |
Power |
KV-28FC60/28FC60-Z: 132 W |
||
consumption |
KV-32FC60/32FC60-Z: 130 W |
||
Dimensions |
KV-28FC60/28FC60-Z |
||
|
498(w) x 834(h) x 527(d) mm |
||
|
KV-32FC60/32FC60-Z |
||
|
559(w) x 924(h) x 559(d) mm |
||
Weight |
KV-28FC60/28FC60-Z |
||
|
Approx. 52 kg |
||
|
KV-32FC60/32FC60-Z |
||
|
Approx. 65 kg |
||
Accessories |
1 remote control RM-892 |
||
supplied |
2 batteries |
||
|
1 instruction manual |
||
|
1 rear cover (for KV-28FC60Z/ |
||
|
32FC60Z models only). |
||
Other Features |
Flat display Trinitron tube, digital |
||
|
noise reduction, 100 Hz picture, |
||
|
graphic equaliser, personal ID, |
||
|
sleep timer, NexTView, NICAM |
||
|
stereo, Digital Comb Filter |
25
Additional Information
Troubleshooting
Here are some simple solutions to problems which may affect the picture and sound.
Problem |
Solution |
|
|
No picture (screen is dark), no sound |
• Plug the TV in. |
|
|
|
• Press Uon the TV. (If uindicator is on, press ;, PROGR+/- |
||
|
or one of the numbered buttons on the remote control.) |
||
|
• Check the aerial connection. |
||
|
• Check if the selected video source is on. |
||
|
• Turn the TV off for 3 or 4 seconds and then turn it on again using U. |
||
|
|
|
|
Poor or no picture (screen is dark), |
• Press MENU. Select |
|
and adjust Brightness, Contrast |
but good sound |
and Colour. |
|
|
Good picture, but poor or no sound |
• Press ¸+ . |
|
|
|
• If ¤is displayed on the screen, press ¤button. |
||
No colour for colour programmes |
• Open the cover of the remote control. Press ?button. |
||
Remote control does not function |
• Replace the batteries. |
|
|
Control Panel does not function |
• Make sure Parental lock is Off. |
Note: As with some other electrical appliances under certain circumstances there is potential for small electrostatic discharge to occur.
If you continue to have problems, have your TV serviced by qualified personnel. Never open the casing yourself.
Channel Guide
TV System |
Receivable Channels |
Channel Display |
|
|||||||
B/G/H |
E2 .. |
|
12, 21 .. |
69 |
|
C02 C03 C04 .. |
C12 C21 .. |
C69 |
||
TV Cable (1) |
S1 .. |
|
41 |
|
|
S01 S02 .. |
S41 |
|
|
|
TV Cable (2) |
S01 |
|
.. S05, M1 .. |
M10, U1 .. U10 |
S42 .. |
S46 S01 .. |
S10 S11 .. |
S20 |
||
Italy |
A B C D E F G H H1 H2, 21 .. 69 |
C13 C14 C15 C16 C17 C18 C19 C20 C11 C12, C21-C69 |
||||||||
D/K |
R01 |
.. R12, R21 |
.. R69 |
C01 .. |
C12 C21 .. |
C69 |
|
|||
TV Cable (1) |
|
|
|
|
|
S01 S02 .. |
S41 |
|
|
|
TV Cable (2) |
|
|
|
|
|
S42 S43 .. |
S46 |
|
|
|
TV Cable |
B .. |
Q*, S21 .. |
F41 |
S02, S03 .. |
S17, S21 .. S41 |
|
||||
L |
F2 .. |
|
F10 F21 |
.. F69 |
C01 .. |
C12, C21 |
.. C69 |
|
||
I |
B21 |
.. |
B68 |
|
|
C21 .. |
C68 |
|
|
* If channels B..Q are available, the display S02-S17 will appear on the screen.
26
27
28