Rover KneeRover User Manual

KneeRover® Economy

Knee Scooter

User Manual

Congratulations on your purchase of the KneeRover

®

Economy Knee Scooter!

The KneeRover® Economy Knee Scooter provides a more reliable and
comfortable alternative to crutches for patients needing an effective
mobility solution at an affordable price.

Operating Instructions:

This medical device is designed to maximize mobility during your recovery
from foot/ankle surgery or injury.

Place the knee of your injured leg on the knee platform and stand as
straight as possible. Adjust the handlebar to waist height so the arms and
hands are in a comfortable position. Adjust the knee platform so that your
injured leg is supported at a 90 degree angle when standing.

Ensure that the hand brake is fully engaged before mounting the
KneeRover® scooter. To move the scooter, simply push forwards or
backwards with your good foot. Allow the scooter to glide, and as it slows
down, push again.

Safety First:

The KneeRover® scooter is designed for easy steering and stopping and
should be used to carefully move about at slow, controlled speeds. When
turning the scooter you should have the brake applied and be moving at a
slow, safe, controlled speed. It is easy to tip the scooter if you are making a
turn with too much speed. Use caution and balance and operate at your
own risk.

With routine use, nuts and bolts on the steering column and brake
mechanism can and likely will become loose. Periodically check nuts and
bolts after use and re-tighten as appropriate.

Economy Knee Scooter

Set Up Instructions:

Please follow the step by step instructions on the following pages to
properly assemble your KneeRover® scooter. The diagram below
identifies the key components of the scooter to aid with assembly.

Visit kneerover.com for assembly videos.

Setup Instructions:

Step 1: Install Handlebars & Steering Column

Please carefully complete all steps before operating your new KneeRover
scooter. The steering column and handlebars will be separate and in a
folded position when unpacking. Insert the handlebars into the steering
column, making sure not to twist the brake cables. Next, raise the steering
column and push the clamp lever to the left to allow security pin to lock into
place (as shown below). Raise the clamp lever upward and tighten by
turning it clockwise. Finally, push clamp lever down firmly to secure the
steering column (as shown below). Reverse these steps when needing to
lower steering column for transport.

Step 2: Rotate Front Wheels & Set Guide Pin

Pull down the guide pin ring as shown below, and turn the handlebars so
that the front wheels and brake handles are facing forward. The BACK

sticker MUST be facing back toward the rear wheels with the guide

pin between the guide stops. (see photos on top of next page). Be sure

that the brake cables are not twisted. The front of the scooter should look
similar to the picture on the previous page.

Hand Brake Levers

Handlebar Height
Adjustment Knob

Quick Release

Clamp

Steering Column

Brake Cable

Weight Capacity = 300 pounds

Steering Column

Guide Pin

Non-Marking

7.5” Wheels

Adjustable

Knee Platform

Rear Brake
Mechanism

Push Clamp Lever to Left

Clamp Lever

Guide Pin Ring

Pull Ring Down

Step 2: Rotate Front Wheels & Set Guide Pin (cont.)

Step 3: Install Knee Platform & Adjust Height

The knee platform is designed to be used with either the right or left
leg. Insert the knee platform post into the receptacle tube. Next, set
the knee platform at your desired height for use by inserting the
locking pin through the aligned holes. Finally, tighten the clamp lever
to secure the knee platform in place. Once knee platform is locked in
place, install the black knob (as shown below) to set the handlebars at
a comfortable height for operation (typically at waist height).

Step 4: Brake Operation

To engage the brake, squeeze the brake lever on handle bar.

Your KneeRover® scooter comes equipped with a brake lock /
parking brake. Simply squeeze brake handle firmly and press the
button to engage the lock. To release the lock, squeeze the brake
handle again.

Ongoing Maintenance

With routine use, nuts and bolts on the steering column and brake
assembly can become loose. To ensure safe continuous operation of
this KneeRover® scooter, it is important to periodically inspect the
scooter for loose nuts and bolts and re-tighten as appropriate.

Please visit kneerover.com/pages/kneerover-maintenance-

videos for additional support in maintaining your KneeRover® knee

walker..

Locking Pin

Black Knob
for Steering
Height
Adjustment

BACK sticker

MUST face
back toward
rear wheels

Steering
Guide Pin

Steering
Guide Stops

Clamp
Lever

Brake Lock

Your Satisfaction is Our Top Priority:

Thank you for your business – we appreciate having you as a customer!
We are committed to providing innovative and affordable mobility
solutions to get you moving as soon as possible after injury or surgery
and for the duration of your recovery – free to go about your busy,
active life – and have a little fun doing it.

We hope that you are completely satisfied with your purchase. If you
have any issues, please contact us and we will do everything possible
to help you. Reviews have a significant impact on our small business.
If you purchased this product on Amazon or eBay, we would greatly
appreciate a review once you’ve had a chance to use your new
KneeRover® scooter. We hope we’ve earned a 4 or 5 star review – if
not, please give us the opportunity to help you before leaving a review.
Thank you for your support. We appreciate you!

Need Help – Contact Us:

Phone: [phone]
Email: [e-mail]
Web: www.kneerover.com
Assembly Support: kneerover.com/pages/assembly-video

EU AUTHORIZED REPRESENTATIVE

Murray's Medical Equipment Ltd
Airton Park, Airton Road, Tallaght,
Dublin 24 (Eircode D24 DY09), Ireland
T: 00 353 1 855 5696
www.murrays.ie

Limited Lifetime Warranty

This warranty applies only to the original purchaser.

This device was built to exacting standards and carefully inspected
prior to shipment. Your KneeRover® brand product is warranted to
be free of defects in materials and workmanship for a period of one
year from the date of purchase. The side frames and cross braces
are warranted for the lifetime of the KneeRover® scooter.

This warranty does not cover device failure due to owner misuse,
negligence, or normal wear and tear. The warranty does not extend
to non-durable components, which are subject to normal wear and
need periodic replacement. These components include, but are not
limited to tires, grips, brake pads and upholstery.

The warranty shall not apply for damages or defects caused by
unauthorized parts, attachments or repairs, negligence, accident, or
any circumstances beyond the control of KneeRover®, such as
improper operation, maintenance or storage.

If you have any questions regarding your KneeRover® product or
this warranty, please contact our Customer Care Team. We are
available, for your convenience, toll free at 1-877-737-9877,
Monday – Friday from 9 am to 5 pm Eastern.

Need Parts or Accessories?

Add an accessory like a knee pad cover, cup holder or headlight to
enhance your experience on your new KneeRover® scooter. Keep
your scooter operating in top shape with original manufacturer
parts. Visit kneerover.com, to explore our full range of parts and
accessories.

KneeRover® is a registered trademark of Rover Mobility, LLC.