PURE DAP-601ES, SAT 4 Owner's Manual
Owner’s manual..........
Besitzerhandbuch ......
Manuel d'utilisation ...
Safety instructions
Keep the unit away from heat sources.
Do not use the unit near water.
Avoid objects or liquids getting into the unit.
Unplug the power lead if the unit will not be
used for a long period.
Sicherheitsvorschriften
Halten Sie der DAP-601ES von Wärmequellen
fern.
Betreiben Sie der DAP-601ES nicht in
unmittelbarer Wassernähe.
Verhindern Sie jegliches Eindringen von
Flüssigkeit in das Innere der DAP-601ES.
Unterbrechen Sie die Stromzufuhr zum
DAP-601ES, wenn sie es für längere Zeit nicht
nutzen.
Consignes de Sécurité
Ne pas placer l'unité à proximité d’une source
de chaleur.
Protéger l'unité contre la pluie et l’humidité.
Veiller à ce qu’aucun objet ou liquide ne
pénètre dans l'unité.
Débrancher le câble d’alimentation en cas de
non utilisation prolongée de DAP-601ES.
Mains safety
The unit uses a 230V AC 50 Hz power supply.
When replacing the fuse in the
supplied moulded mains plug,
always refit the integral fuse
holder/cover. Always fit a 3
amp fuse either in the plug or adapter, or at
the distribution board.
Do not attempt to remove any screws or open
the unit. No user serviceable parts are inside.
For your safety, always obey the warning:
CAUTION - RISK OF ELECTRIC SHOCK - DO
NOT OPEN COVER
Sicherheit im Umgang
mit Netzstrom
DAP-601ES benötigt eine Betriebsspannung
von 230 Volt Wechselstrom mit 50 Hz.
Versuchen Sie keinesfalls der
DAP-601ES zu öffnen. Es
befinden sich keine Teile
innerhalb des Gehäuses, die
vom Benutzer gewartet werden können.
Für Ihre Sicherheit beachten Sie folgendes:
ACHTUNG - GEHÄUSE NICHT ÖFFNEN -
LEBENSGEFÄHRLICHE SPANNUNG.
Sécurité électrique
L'unité doit être branché sur une tension secteur
de 230 V CA 50 Hz.
Ne pas tenter d’ouvrir l'unité.
Aucune des pièces se trouvant à
l’intérieur ne peut être réparée
par l’utilisateur.
Respecter la consigne de sécurité suivante:
ATTENTION – RISQUE DE CHOC ÉLECTRIQUE – NE
PAS OUVRIR LE BOÎTIER.
Copyright
Copyright 2002 by Imagination Technologies Limited. All rights reserved.
No part of this publication may be copied or distributed, transmitted,
transcribed, stored in a retrieval system, or translated into any human or
computer language, in any form or by any means, electronic, mechanical,
magnetic, manual or otherwise, or disclosed to third parties without the
express written permission of Imagination Technologies Limited.
Copyright
Copyright 2002 Imagination Technologies Limited. Alle Rechte
vorbehalten. Kopien, auch auszugsweise, von diesem Dokument, egal in
welcher Form, bedürfen der schriftlichen Genehmigung von Imagination
Technologies Limited.
Copyright
Copyright 2002 par Imagination Technologies Limited. Tout droits
réservés. Il est interdit de copier, distribuer, transmettre, transcrire,
traduire et archiver tout ou partie de ce document, sous quelque forme
que ce soit et par tout procédé que se soit, sans l’autorisation écrite
préalable de Imagination Technologies Limited.
Disclaimer
Imagination Technologies Limited makes no representation or warranties with
respect to the content of this document and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. Further,
Imagination Technologies Limited reserves the right to revise this publication
and to make changes in it from time to time without obligation of Imagination
Technologies Limited to notify any person or organization of such revisions or
changes.
Trademarks
PURE, the PURE logo, VideoLogic, the VideoLogic Logo, Imagination
Technologies, and the Imagination Technologies logo are trademarks or
registered trademarks of Imagination Technologies Limited. All other product
names are trademarks of their respective companies.
Credits
This manual was written by Bruce Murray and illustrated by Nick Noble. It is a
product of VideoLogic Systems, Imagination Technologies Ltd., Home Park
Estate, Kings Langley, Hertfordshire WD4 8LZ, UK.
Edition 1 May 2002
Haftungsausschluß
Imagination Technologies Limited übernimmt keine Haftung, bzw.
Gewährleistung,, die über den Inhalt dieses Dokuments hinausgehen und
schließt alle implimierten Gewährleistungsansprüche aus. Desweiteren behält
sich Imagination Technologies Limited das Recht vor, ohne vorherige
Ankündigung oder Benachrichtigung einzelner Personen, bei Bedarf Änderungen
und Ergänzungen an diesem Dokument vorzunehmen.
Warenzeichen
PURE, das PURE logo, VideoLogic, das VideoLogic logo, Imagination
Technologies, und das Imagination Technologies logo sind Warenzeichen, bzw.
eingetragene Warenzeichen von Imagination Technologies Limited. Alle
anderen gennanten Warenzeichen und Markennamen gehören Ihren
jeweiligen Besitzern.
Impressum
Dieses Manual wurde von Bruce Murray erstellt unt Ilustrationen von Nick
Noble. Dies ist ein Produkt von VideoLogic Systems, Imagination Technologies
Limited, Home Park Estate, Kings Langley, Hertfordshire WD4 8 LZ, Groß
Britannien.
Erstausgabe Mai 2002
Limitation de responsabilité
Cette publication n’implique aucun engagement contractuel de
Imagination Technologies Limited concernant la présentation ou les
garanties. En particulier, Imagination Technologies Limited refute toute
garantie implicite d’usage ou de valeur marchande, pour quelque but que
ce soit. En outre, Imagination Technologies limited se réserve le droit de
modifier cette publication et d’y opérer des changements ponctuels, sans
avoir l’obligation d’en informer quelque personne ou organisation que ce
soit.
Marques déposées
PURE, le logo PURE, VideoLogic, le logo VideoLogic, Imagination
Technologies et le logo Imagination Technologies sont des marques et des
marques déposées de Imagination Technologies Limited. Tous les autres
noms de produits sont des marques de leur compagnie respective.
Crédits
Ce manuel a été écrit par Bruce Murray et illustré par Nick Noble. C’est
un produit de VideoLogic Systems, Imagination Technologies Limited,
Home Park Estate, Kings Langley, Hertfordshire WD4 8LZ, United
Kingdom.
Premier edition Mai 2002
1
Contents
Introduction..........................................................................................2
Unpacking ............................................................................................ 3
Overview diagrams ...............................................................................3
Front Panel ..................................................................................................................................... 3
Rear Panel ...................................................................................................................................... 4
Remote Control .............................................................................................................................. 4
Connecting up.......................................................................................5
Connecting to your source units ..................................................................................................... 5
Connecting to your amplifier .......................................................................................................... 5
Connecting to the power supply...................................................................................................... 5
Using your DAP-601ES ..........................................................................6
Switching on and off ....................................................................................................................... 6
Testing your system ....................................................................................................................... 6
Selecting an input ........................................................................................................................... 6
Adjusting the volume ...................................................................................................................... 6
Adjusting the sound ........................................................................................................................ 7
Saving and loading your favourite settings..................................................................................... 8
Resetting your unit ......................................................................................................................... 8
Troubleshooting ...................................................................................9
Accessories ..........................................................................................9
Technical Support ................................................................................. 9
Warranty information ...........................................................................9
Technical Specifications ...................................................................... 10
2
Introduction
Thank you for choosing the PURE DAP-601ES Digital Audio Processor.
The DAP-601ES advanced digital audio processor features full support for PCM Stereo, DTS (Digital Theatre Systems), Dolby Digital 5.1 formats
and Dolby Pro Logic II, while providing a full range of EQ and DSP effects. All settings are easily accessible via the remote control and can be
stored as presets, enabling you to choose different listening modes for movies, music or TV at the touch of a button. A full range of bass
steering options is also provided with the visual indicator on the front panel showing the selected mode.
The DAP-601ES is part of the acclaimed LiFE 4/10 home cinema and hi-fi surround system which consists of the following four components:
DAP-601ES Advanced digital audio processor with full support for PCM Stereo, DTS (Digital Theatre Systems), Dolby Digital 5.1 formats and
Dolby Pro Logic II (5.1), while providing a full range of EQ and DSP effects.
MCP-601ES Dedicated slimline amplifier providing five discrete channels of low-noise distortion-free amplification.
SAT 4 Five D'Appolito satellite speakers, each with two custom made 4" Audax high definition aerogel drive units and the latest 20
mm textile dome Audax tweeter with neodymium magnets and ferrofluid cooling.
SUB 10 Powerful subwoofer featuring a 10" ultra long-throw drive unit with high power voice coil, giving full deep bass response
The following sections provide information on setting up and using your DAP-601ES.
3
Overview diagrams
This section provides information on the controls and connectors available on the front and rear panels of your DAP-601ES and the infrared
remote control.
Front Panel
1. Power button. Switches the unit on or returns it to standby. Indicator LED shows when the unit is switched on.
2. Remote sensor. Picks up the infrared signal from the remote.
3. Backlit 16 x 2 LCD display. Provides information regarding the system status and settings.
4. Standby LED. Indicates unit in standby mode with power connected.
5. Channel LEDs. Represent the status of an individual channel. When a particular channel is active, the LED lights up. The colour of the LED
indicates the frequency range of that channel:
– Red This channel has been set to output the full frequency range including lower frequencies below 60, 90 or 120 Hz.
– Green This channel doesn’t contain the lower frequencies below 60, 90 or 120 Hz.
See Adjusting bass distribution on page 8 for details of how to limit the frequency range of a channel.
Unpacking
This section lists the contents of your DAP-601ES package. After unpacking your box, check that you have all of the following items.
Contact us if any items are missing or damaged.
1. DAP-601ES Digital Audio Processor unit
2. Infrared remote control handset
3. Two AA batteries for the remote control handset
4. 6-way, 0.5m gold-plated phono to phono cable for connection to your MCP-601ES or other amplifier
5. Optical S/PDIF Toslink to Toslink cable for connection to your DVD player or other audio source
6. Power cable with moulded UK 3-pin (3A fused) plug or European 2-pin plug
7. Warranty registration card
Input
Power
Mute
Pro Logic II
Acoustics EQ on/off EQ setup
Test
Balance
Delay
Preset 1
Preset 2 Preset 3
Save
Preset 4 Load
Bass Manager
Centre
SL/SR
SUB
DRC
Reset
DelayVolume
Merci d'avoir rempli ce questionnaire.
Enregistrement du LiFE 4/10
Nom......................................................................................................
Adresse ..................................................................................................
........................................................................................................................
Pays.......................................................... Code postal ............................
Téléphone .............................................. Fax ..........................................
E-mail ....................................................................................................
Age
moins de 20 21 à 30 31 à 45 plus de 45
Comment avez-vous eu connaissance du LiFE 4/10 ?
........................................................................................................................
Lieu d'achat ........................................ Date d'achat ..................................
Veuillez préciser le numéro de série de votre ou vos unité(s) ci-après :
DAP-601ES .................................................................................................
MCP-601ES .................................................................................................
SUB 10 .................................................................................................
SAT 4
(
Noir Erable
)
................................. ........................................
............................. .................................. ........................................
Pourquoi avez-vous choisi le LiFE 4/10 ?
.........................................................................................................................
À quoi allez-vous le raccorder ?.........................................................................
Constructeur?..................................Modèle?....................................................
Avez-vous des commentaires concernant le(s) produit(s) ?...............................
..............................................................................................................
Quelle a été l'importance des facteurs suivants dans votre décision d'achat ?
Important Pas important
Articles de presse
1 2 3 4 5 6
Caractéristiques
1 2 3 4 5 6
Design/look
1 2 3 4 5 6
Marque VideoLogic/PURE
1 2 3 4 5 6
Prix
1 2 3 4 5 6
Quels sont vos 5 magazines préférés ?
..................... ..................... ...................... .................... ...................
Autres produits Votre PC
Déjà acheté Achat prévu dans Processeur
Lecteur portable MP3 1 mois 3 mois 6 mois Intel Cyrix
Lecteur de DVD 1 mois 3 mois 6 mois AMD
Radio numérique 1 mois 3 mois 6 mois Autre..............
Ecran plasma 1 mois 3 mois 6 moisDébit (MHz)
Système de HP sans fil 1 mois 3 mois 6 mois <750MHz 750-1.2
Réseau domestique 1 mois 3 mois 6 mois 1.3-2.0 >2.0
Veuillez m'envoyer davantage d'informations sur : Les produits VideoLogic
les produits PURE
De temps à autre, nous mettons nos listes d'adresses à la disposition de partenaires triés sur le volet.
Si vous préférez ne PAS rendre ces informations disponibles pour d'autres, cochez ici
Nous aimerions savoir ce que vous pensez de nos produits et demandons l'autorisation de vous citer
dans du matériel promotionnel le cas échéant. Si vous ne souhaitez PAS que votre avis soit publié,
cochez ici
Vielen Dank für Ihre Zeit.
LiFE 4/10 Registrierungsdaten
Andere Produkte Über Ihren PC
Bereits gekauft Plane zu kaufen in Prozessortyp
Portabler MP3-Player 1 Mt 3 Mte 6 Mte Intel Cyrix
DVD-Player 1 Mt 3 Mte 6 Mte AMD
DAB Digital Radio 1 Mt 3 Mte 6 Mte Anderer....................
Plasma-Bildschirm 1 Mt 3 Mte 6 Mte Takt ( GHz )
Drahtlose Lautsprecher 1 Mt 3 Mte 6 Mte <750MHz 750-1.2
Netzwerk 1 Mt 3 Mte 6 Mte 1.3-2.0 >2.0
Bitte senden Sie mir mehr Informationen über: VideoLogic-Produkte
PURE-Produkte
Gelegentlich stellen wir unser Adressenverzeichnis sorgfältig ausgewählten Partnern zur Verfügung. Falls Sie
es vorziehen, diese Informationen NICHT verfügbar zu machen, kreuzen Sie bitte dieses Kästchen an
Wir begrüßen Ihre Ansichten zu unseren Produkten und möchten Sie um Erlaubnis bitten, diese wo
zutreffend in unserem Werbematerial zitieren zu dürfen. Falls Sie NICHT wünschen, dass Ihre Aussagen
benutzt werden, kreuzen Sie bitte dieses Kästchen an
Name .....................................................................................................
Adresse ..................................................................................................
........................................................................................................................
Land........................................................ Postleitzahl ..............................
Telefon ....................................................Fax .........................................
E-mail ..................................................................................................
Alter
bis 20 21 bis 30 31 bis 45 über 45
Wie haben Sie sich über das LiFE 4/10-System informiert?
........................................................................................................................
Gekauft bei ........................................ Kaufdatum .....................................
Bitte tragen Sie unten die Seriennummern Ihrer Geräte ein:
DAP-601ES .................................................................................................
MCP-601ES .................................................................................................
SUB 10 .................................................................................................
SAT 4
(
Schwarz Ahorn
)
................................. ........................................
............................. .................................. ........................................
Warum haben Sie sich für LiFE 4/10 entschieden?
.........................................................................................................................
Was werden Sie anschließen?...........................................................................
Hersteller?..................................Model?..........................................................
Haben Sie Anmerkungen zu den Produkten? ..................................................
..............................................................................................................
Wie wichtig waren bei Ihrer Kaufentscheidung die folgenden Punkte?
Wichtig Nicht wichtig
Presseberichte
1 2 3 4 5 6
Features
1 2 3 4 5 6
Design/Aussehen
1 2 3 4 5 6
Der Name VideoLogic/PURE
1 2 3 4 5 6
Preis
1 2 3 4 5 6
Welche sind Ihre 5 beliebtesten Magazine?
..................... ..................... ...................... .................... ...................
Thank you for your time.
LiFE 4/10 Registration Details
Other products About your PC
Already bought Planning to buy in Processor type
Portable MP3 player 1 mth 3 mths 6 mths Intel Cyrix
DVD player 1 mth 3 mths 6 mths AMD
DAB Digital Radio 1 mth 3 mths 6 mths Other ...............................
Plasma screen 1 mth 3 mths 6 mths Speed (GHz)
Wireless speaker system 1 mth 3 mths 6 mths <750MHz 750-1.2
Home networking 1 mth 3 mths 6 mths 1.3-2.0 >2.0
Please send me more information about: VideoLogic products
PURE products
Occasionally we make our mailing lists available to carefully selected partners. If you would prefer NOT
to make this information available to others please tick here
We appreciate any views you have on our products and would like your permission to quote them in
promotional material if appropriate. If you would prefer your views were NOT used, please tick here
Name ..............................................................................................................
Address ..........................................................................................................
........................................................................................................................
Country ....................................................... Postcode ...................................
Telephone .................................................... Fax ...........................................
E-mail .............................................................................................................
Age
up to 20 21 to 30 31 to 45 over 45
Where did you hear about the LiFE 4/10 system?
........................................................................................................................
Purchased from ...............................................Date .......................................
Please enter serial numbers of your unit(s) below:
DAP-601ES .................................................................................................
MCP-601ES .................................................................................................
SUB 10 .................................................................................................
SAT 4
(
Black Maple
)
................................. ........................................
............................. .................................. ........................................
Why did you choose LiFE 4/10? .......................................................................
.........................................................................................................................
What will you connect it to?..............................................................................
Manufacturer?..................................Model?.....................................................
Do you have any comments about the product(s)? ...........................................
.........................................................................................................................
How important to your buying descision were the following ?
Important Not important
Press reviews
1 2 3 4 5 6
Features
1 2 3 4 5 6
Design/appearance
1 2 3 4 5 6
VideoLogic/PURE name
1 2 3 4 5 6
Price
1 2 3 4 5 6
What are your 5 favourite magazines?
...................... ....................... ........................ ...................... ......................
UK only
Europe
4
Input
Power
Mute
Pro Logic II
Acoustics EQ on/off EQ setup
Test
Balance
Delay
Preset 1
Preset 2 Preset 3
Save
Preset 4 Load
Bass Manager
Centre
SL/SR
SUB
DRC
Reset
DelayVolume
Rear Panel
OUTPUT INPUT
AUX VCR TV
S/PDIF
LC
R
RLRLR
L
Made in the UK
SL
SR SW
PURE DAP-601ES
by VideoLogic
1. The six main outputs — Front Left (L), Front Right (R), Surround Left (SL), Surround Right (SR), Centre (C) and Sub (SW) feed audio signals
to the matching inputs on your MCP-601ES multi-channel power amplifier.
2. AUX, VCR and TV inputs accept signals from stereo analog sources.
3. S/PDIF inputs. Optical (Toslink) and coaxial digital inputs. Connect the digital outputs of your DVD player or other sound source to these
inputs.
4. Power socket and fuse holder with spare fuse.
Remote Control
Input Selects from the 5 different source inputs
Power Turns the unit on or returns it to standby mode
Mute Mutes all channels (toggle on/off)
Test Outputs a test signal for left, right, centre and surround channels
Balance Sets the volume level for each of the 6 channels
Delay Enables time delay adjustment for your surround and centre speakers
Pro Logic II Selects from 4 different surround settings
Acoustics Selects from 6 different sound fields
EQ on/off Enables/disables EQ settings
EQ setup Enables adjustment of the 5 EQ band settings
Preset (1-4) Selects from 4 presets
Save Stores your settings to a selected preset
Load Applies the settings stored in selected preset
Bass Manager Switches between four bass configurations
Centre Activates/deactivates the centre channel speaker
SL/SR Activates/deactivates the surround speakers
SUB Activates/deactivates the subwoofer
DRC Select from 3 dynamic range compression ratios
Volume +/– Increases/decreases the output volume
Delay +/- Increases/decreases the delay time
Reset Resets the unit to the factory default settings
5
Connecting up
This section provides information on connecting your DAP-601ES to your source units, your amplifier and your power supply. Before connecting
devices to your DAP-601ES we recommend switching both devices off.
Connecting to your source units
The following line level input connectors on the rear of your DAP-601ES enable you to connect up to five source units:
AUX, VCR and TV Gold plated coaxial analogue stereo inputs, connect to a CD player, radio tuner, VCR or other stereo source using dual phono
to dual phono cables. Connect red to red and white to white (or black).
S/PDIF optical Optical digital input, connect to the digital output of your DVD player or other multi-channel source using the supplied optical
cable. Remove the plastic plug to gain access to the socket.
S/PDIF coaxial Coaxial digital input, an alternative digital connection if your source does not have an optical connector or for connecting to a
second digital source. Connect using a suitable coaxial cable.
Once connected, you can then choose between source units using the Input button on the remote control, see Selecting an input on page 6.
Connecting to your amplifier
To get sound from your DAP-601ES you need to connect it to your speakers via a multi-channel amplifier such as the PURE MCP-601ES.
Connect the Left (L), Right (R), Surround Left (SL), Surround Right (SR), Centre (C) and Subwoofer (SW) output connectors to the
corresponding input connectors on your amplifier using the supplied 6-way phono cable. If you have an amplifier with no subwoofer input, the
subwoofer output can be connected directly to an active subwoofer.
Connecting to the power supply
Once all audio connections are complete, as described above, connect the power cable to the power socket on the rear panel of your DAP601ES and the other end to a wall power outlet.
6
Using your DAP-601ES
This section provides information on the operation of your DAP-601ES. The DAP-601ES is simple to operate with all functions available from the
remote control. Insert the batteries in the remote control and aim at the remote sensor on the front panel. Remove the protective film over the
display panel before using the unit.
Input
Switching on and off
Before switching on for the first time, check all audio connections.
Ensure that the power cable is connected and the power is on at the wall.
The DAP-601ES enters a standby mode when you connect it to the power, this is indicated by the red standby LED to the right
of the display.
Push and release the Power button on the front of your DAP-601ES or on the remote control to switch the unit on or return to
standby mode. The blue power on LED and display will light up when the unit is switched on.
Testing your system
After connecting your source, amplifier and speakers, press and release the Test button to test your system. You can also use
the test mode to test the location of the speakers. When the Test button is pressed, white noise is generated in turn through
all satellite speakers in the order Front Left, Centre, Front Right, Surround Left, and Surround Right channels for 2 seconds
each. The display simultaneously indicates which channel is being tested. If you press the Test button during playback the
sound will be interrupted for the period of the test and return to your source when finished.
Selecting an input
The DAP-601ES surround sound processor is capable of processing the digital and analog audio signals from many different
audio sources. The DAP-601ES automatically detects and decodes the digital signal and shows the signal type on the display.
The DAP-601ES can be connected to up to five audio sources using the connectors on the rear panel. Select the input source
you want by repeatedly pressing the Input button until the desired source is selected. The input selected will be shown on the
top line of the display.
AUX Coaxial analogue input labelled AUX on the rear panel
VCR Coaxial analogue input labelled VCR on the rear panel
TV Coaxial analogue input labelled TV on the rear panel
COAXIAL (CO) Coaxial digital input labelled S/PDIF on the rear panel
OPTICAL (OP) Optical digital input labelled S/PDIF on the rear panel
Adjusting the volume
You can adjust both the overall volume and the volume levels of individual channels to suit your listening environment and
source material.
Adjusting the overall volume
You adjust the overall volume level using the Volume +/- and Mute controls.
Mute Pressing Mute mutes all channel outputs. To disable the mute function, press Mute again. The bottom line of the
display shows MUTE when mute is in operation.
Volume To increase or decrease the master output volume of your DAP-601ES, press Volume + /-. The bottom row of the
display shows the value and this remains on the display after adjusting. The default setting is -30 dB and the
range is from -60 to 0 dB. For information on setting the volume of individual channels see below.
Adjusting the volume of individual channels
You can set the volume level of each individual channel. Note the subwoofer channel adjusts the volume of the bass across
all channels where present. An additional LFE (Low Frequency Effect) MIX channel is also provided. The LFE channel is an
optional band-limited bass channel which may be included on some Dolby Digital recordings to enhance the bass at
particular points.
To adjust the volume of an individual channel, press Balance repeatedly until the desired channel is shown on the bottom
line of the display. Adjust volume on the selected channel by pressing Volume +/-. The default setting for each channel is +0 dB.
Test
Mute
Volume
Balance
Volume
Power
7
Acoustic
s
Volume
Adjusting the sound
Your DAP-601ES enables you to fine tune different aspects of the sound to match your listening environment, the type of
source you are using and your own personal listening preferences.
Setting speaker delay
The Delay function enables you to set a delay for rear and centre speakers to enable you to finely tune your setup to take into
account your speaker positioning and the acoustics of your room.
The recommended listening position is described below and shown opposite.
Ideally the centre channel speaker should be placed the same distance as the left and
right speakers from your listening position.
Rear left and right speakers should be placed behind your listening position and above
ear level.
If, for example, the centre speaker can only be placed nearer to you than the left and
right speakers, sound from the centre speaker will arrive before the sound from the left
and right speakers. The difference in arrival time may affect the sound quality. The delay
function enables you to adjust the speaker delay to compensate for this problem by
increasing the delay time for the centre channel.
To adjust delay, press Delay repeatedly until the required channel is selected then
press Delay +/- until the desired delay is shown on the bottom line of the display. The
delay range for rear speakers is 0 to 15 ms and 0 to 5 ms for centre.
Selecting Pro Logic II modes
Dolby Pro Logic II delivers surround sound from mono, stereo and other types of input signal. Push the Pro Logic II button to
display the current Pro Logic II mode. Push it again and repeat to switch the between the following Pro Logic II modes:
OFF Pro Logic II mode off - Acoustics and Equaliser settings available.
MOVIE Optimised for movies or TV with Dolby surround soundtracks, also good with video games consoles.
MUSIC Creates a rich surround sound from stereo sources such as radio and CDs. In music mode there are three settings
which you can apply:
PAN Panoramic mode - wraps the sound from the front left and right speakers around you.
Push the Pro Logic II button again to select this mode.
C Centre width, enables you to spread the centre channel into the front left and right speakers.
Adjust the value in the range 0-7 using Volume +/-.
D Dimension, enables you to adjust the sound balance from the front to the back to suit your taste.
Adjust the value in the range 0-6 using Delay +/-.
MATRIX Creates surround sound from a mono source.
Applying acoustic effects
Your DAP-601ES is equipped with a sound field processor that provides five different preset acoustic effects designed to alter
the sound to simulate playback in different types of building: Hall, Theatre, Stadium, Club, and Church. Note that these
acoustic effects can only be applied to stereo sources when Pro Logic II is switched off. Push the Acoustics button to display
the current setting. Push it again and repeat to select any of these effects or the Disable setting, which removes any acoustic
effects.
You can also increase or decrease the reverb value from 0-9 by pressing Volume +/- on the remote control whilst you are
selecting the acoustic effect.
Adjusting the frequency equalisation
Your DAP-601ES features a 5-band equalizer which enables you to fine tune the sound of your favourite movie or music.
Note that these frequency settings are only available when Pro Logic II is switched off.
Press EQ setup and repeat to switch between the 5 bands (125 Hz, 370 Hz, 1250 Hz, 3700 Hz and 10500 Hz).
Each band of the equalizer enables you to adjust your desired volume to a maximum of +/-10 dB by pressing Volume +/-.
Press EQ on/off to switch the new EQ settings on or off. The bottom line of the display shows EQ when the EQ settings are on.
Pro Logic II
Delay
Delay
EQ on/off EQ setup
8
Adjusting bass distribution
The six LEDs on the front panel of your DAP-601ES represent the six discrete audio channels (Left, Right, Centre, Surround
Left, Surround Right and Sub). If a particular channel is active, the LED will light up in green. The LED will be red if that
particular channel carries low frequencies below 60, 90 or 120 Hz.
Pressing Bass Manager button enables you to select from four different bass configurations. These selections will distribute
the lower frequencies to different speakers as described below.
Press Volume +/- in any configuration to adjust the frequency threshold between 60, 90 or 120 Hz.
BASS CONFIG. 1 The frequencies below the set level will be passed to the subwoofer and the SW LED will be red.
BASS CONFIG. 2 The frequencies below the set level will be passed to front left and right speakers and the subwoofer and
the L, R and SW LEDs will be red.
BASS CONFIG. 3 The frequencies below the set level will be sent to front, rear speakers and subwoofer and the L, R, SL,
SR and SW LEDs on the front panel will be red.
BASS CONFIG. OFF The frequencies below the set level will be sent to all the speakers; all six LEDs on front panel will be red.
Applying DRC (Dynamic Range Compression)
Your DAP-601ES features Dynamic Range Compression (DRC), this helps to equalise the volume range, for example, in a
movie soundtrack which has dialogue and explosions happening at the same time, DRC will equalise the range by boosting
the dialogue and reducing the explosions so the dialogue can be heard more easily.
Push the DRC button to display the current mode. Push it again and repeat to switch the between the following three modes:
NO No compression is applied to the original audio signal, this provides the greatest dynamic range.
HALF Partial compression is applied.
FULL Full compression is applied.
Switching channels on and off
You can switch channels on and off using the three channel buttons. If a particular channel is active, the appropriate LED on
the front panel will light up.
Pressing Centre switches the centre channel on and off.
Pressing SL/SR switches the surround channels on and off.
Pressing SUB switches the subwoofer on and off.
Saving and loading your favourite settings
The preset function enables you to store up to 4 setting configurations so you can save and load your favourite settings easily.
For example, you may want a preset for listening to music and one for watching a movie. All settings are stored including
volume level, delay, balance, input selection and Pro Logic II settings.
Saving a Preset
1. Press the Preset button (1, 2, 3 or 4) under which you want to save the current settings.
2. Press the Save button to save all the current decoder settings using that preset.
Loading a Preset
1. Press the required Preset button (1, 2, 3 or 4).
2. Press Load to load that preset. If there is no preset stored under that preset, the display shows a PRESET Empty
message.
Resetting your unit
Your DAP-601ES can be reset to its factory default settings by pressing Reset.
Note that resetting your unit will not remove any presets you have stored.
DRC
Preset 1
Save
Load
Bass Manager
Centre
SL/SR
SUB
Volume
Reset
9
Troubleshooting
I can’t hear any sound or sound is very quiet
z Make sure your DAP-601ES and amplifier are switched on
z Check that you have connected the DAP-601ES to your amplifier and source correctly
z Check that you have selected the correct input, see Selecting an input on page 6
z Check that MUTE is not selected or that your amplifier is not turned down
No sound from a single or pair of speakers
z Check that the relevant speaker channel is switched on by checking that the corresponding LEDs are lit up on the front panel, see Switching
channels on and off on page 8
z Check that the speaker wires are securely connected to your amplifier and speaker
z If there is no sound from your powered subwoofer, check that it is turned on and connected correctly
I can’t apply acoustic effects or adjust equalisation
z Check that Pro Logic II is not switched on, see Selecting Pro Logic II modes on page 7
z Check that you are not processing a multi-channel signal – acoustic effects are not applicable to these sources
Remote control not functioning
z Check that you have inserted the batteries correctly
z Ensure that the remote sensor on the front panel is not obscured
z Move closer to the unit and try again, if it works, this could be sign of weak batteries or that you were too far away from the unit
My remote is lost or broken
If your remote does not function and you have confirmed that it is not due to any of the reasons given above, contact your retailer or VideoLogic
Technical Support to obtain a replacement.
Accessories
VideoLogic supply a range of accessories, including speaker cables, speaker stands and brackets and complementary products including DAB
digital radios and amplifiers.
Visit our website at www.videolologic.com or call us on 01923 277 488 to find out more.
Technical Support
The Troubleshooting section of this manual lists some of the more likely reasons for problems you might encounter with your DAP-601ES.
If you still have a problem with your unit, contact your retailer, visit our website at www.videologic.com or contact us using the details on the
back cover of this manual for the latest support information.
Warranty information
VideoLogic Systems Ltd. (“VideoLogic”) warrants to the end user that this product will be free from defects in materials and workmanship in the
course of normal use for a period of two (2) years from the date of purchase.
Please return the enclosed warranty card to your nearest VideoLogic centre to register your product with us.
Loading...